Maxon SP-200 Instructions Manual

SP-200 Series

Synthesized Scanning Radio

Operating Instructions

Table of Contents

About Your SP-200 Series Radio About Maxon / Topaz3 Safety Information Unpacking Information SP-200 Series Features Description of Radio Components Antenna Installation Installing and Removing the Battery Pack Attaching and Removing the Belt Clip Battery Charging and Care SP-200 Series Operation

Power On - Volume - Power Off Channel Select /Channel Group Scan

To Transmit Status Indicators and Audible Alert Tones Scan Modes

Normal Channel Scan Priority Channel Scan

Other Scanning Features

Look Back Scan Channel Delete CTCSS/DCS Scanning Normal Scan TX Priority Scan TX Priority Only TX Receive Only Scan

Scan List Edit

Channel Group Edit

Priority Channel Edit FCC Licensing Service Recycling / Disposal of Batteries Software Copyrights Maintenance Product Warranty

...................................................................................1

...................................................................................................1

.........................................................................................................1

..................................................................................................2

...................................................................................................3

.................................................................................3

........................................................................................................4

......................................................................4

...........................................................................4

............................................................................................4

................................................................................................5

...............................................................................5

........................................................................5

................................................................................................................5

......................................................................6

....................................................................................................................7

............................................................................................7

............................................................................................8

...............................................................................................8

..............................................................................................................8

.............................................................................................8

...........................................................................................9

.....................................................................................................9

................................................................................................9

.................................................................................................................9

..............................................................................................9

...........................................................................................10

..............................................................................................................11

........................................................................................................................11

..................................................................................11

....................................................................................................12

................................................................................................................12

.........................................................................................................13

Contenido

Acerca de su radio Serie SP-200 Acerca de Maxon Información sobre seguridad Información para desempacar Funciones de la Serie SP-200 Descripción de los componentes del radio Instalación de la antena Cómo instalar y retirar el paquete de las pilas Asegurar y quitar el clip de cinturón Cómo cargar y mantener la pila Funcionamiento de Serie SP-200

Encendido - volumen - apagado Selección de canales / Búsqueda del grupo de canales

Para transmitir Indicadores de estado y tonos audibles de alerta Modos de búsqueda

Búsqueda normal de canales

Buscar canal prioritario Otras funciones de búsqueda

Mirar atrás

Cómo borrar un canal de la lista de búsqueda

Búsqueda CTCSS / DCS

Búsqueda TX normal

Búsqueda TX prioritaria

TX prioritaria solamente

Búsqueda para recibir solamente Editar la lista de búsqueda

Editar el grupo de canales

Editar canal prioritario Licencia de la FCC Servicio Reciclado / eliminación de las pilas Derechos de autor del software Mantenimiento Declaración de garantía

.................................................................................14

.........................................................................................................14

........................................................................................14

.......................................................................................15

.......................................................................................16

..................................................................16

................................................................................................17

...............................................................17

............................................................................17

...................................................................................17

..................................................................................18

...............................................................................18

............................................18

...........................................................................................................18

.........................................................19

.....................................................................................................20

....................................................................................20

..............................................................................................21

.......................................................................................21

................................................................................................................21

...........................................................22

.............................................................................................22

................................................................................................22

............................................................................................22

...........................................................................................22

.............................................................................22

............................................................................................22

........................................................................................22

.............................................................................................23

........................................................................................................24

........................................................................................................................24

..............................................................................24

...................................................................................25

................................................................................................................25

...............................................................................................26

Table des matières

Au sujet de votre poste de radio de la Série SP-200 Au sujet de Maxon Informations sur la sécurité Déballage Caractéristiques des appareils de la série SP-200 Description des composants de la radio Montage de l'antenne Installation et retrait de la batterie Fixation et retrait de l'attache du poste sur la ceinture Charge et entretien de la batterie Utilisation des radios de la série SP-200

Marche - Volume - Arrêt Sélection des canaux / Balayage d'un groupe de canaux

Transmission Indicateurs de statut et tonalités d'avertissement audibles Modes de balayage

Balayage de canaux normal

Balayage d'un canal prioritaire Autres caractéristiques du balayage

Retour en arrière

Effacement des canaux balayés

Balayage CTCSS / DCS

Transmission (TX) avec balayage normal

Transmission (TX) avec balayage prioritaire

Transmission (TX) prioritaire seulement

Balayage sur le mode réception seulement Édition de la liste de balayage

Édition d'un groupe de canaux

Édition d'un canal prioritaire Licence par le FCC Service Recyclage / élimination des batteries Droits de reproduction du logiciel Entretien Garantie de produit

.....................................................27

.......................................................................................................27

............................................................................................27

......................................................................................................................28

..........................................................29

..............................................................................29

..................................................................................................30

................................................................................30

................................................30

.................................................................................30

.......................................................................31

..........................................................................................31

.........................................31

..............................................................................................................31

............................................32

......................................................................................................33

......................................................................................33

................................................................................34

.............................................................................34

......................................................................................................34

.................................................................................35

..............................................................................................35

..................................................................35

.............................................................35

....................................................................35

............................................................35

......................................................................................35

.................................................................................36

.....................................................................................36

.......................................................................................................37

.........................................................................................................................37

...........................................................................37

...............................................................................38

......................................................................................................................38

.....................................................................................................39

Indice analítico

Informações sobre o seu rádio Série SP-200 Sobre a Maxon Informação de Segurança Para desempacotar Características da Série SP-200 Descrição dos componentes do rádio Instalação da antena Instalação e remoção da pilha Para prender e retirar o grampo de cinturão Recarregamento e cuidado da pilha Funcionamento da Série SP-200

Ligado - Volume - Desligado Seletor de canal / sintonização automática de grupo de canais

Para transmitir Indicadores de condição e sinais audíveis de alerta Modos de sintonização automática

Modo normal de sintonização

Sintonização do canal de prioridade Outras características de sintonização

Memória

Apagar canal de sintonização

Sintonização CTCSS / DCS

Sintonização normal TX

Sintonização de prioridade TX

Somente prioridade TX

Somente sintonização de recepção Editar a lista de sintonização

Editar grupo de canais

Editar o canal de prioridade Licenciamento do FCC Serviço Reciclagem / troca da pilha Direitos autorais de software Manutenção Declaração de garantia

................................................................40

...............................................................................................................40

.............................................................................................40

........................................................................................................41

....................................................................................42

...........................................................................42

.....................................................................................................43

......................................................................................43

...............................................................43

..............................................................................43

..................................................................................44

...................................................................................44

..................................44

...............................................................................................................44

.....................................................45

...............................................................................46

..................................................................................46

........................................................................47

...............................................................................47

..................................................................................................................47

...................................................................................48

.....................................................................................48

............................................................................................48

.................................................................................48

............................................................................................48

..........................................................................48

.........................................................................................48

..............................................................................................48

.....................................................................................49

.................................................................................................50

.........................................................................................................................50

.........................................................................................50

........................................................................................51

................................................................................................................51

................................................................................................52

About Your SP-200 Series Radio

Maxon's SP-200 Series synthesized radios feature up to 13 scan groups with up to 16 channels per group for a total capacity of 199 channels.

To assure satisfaction from the radio, we urge you to thoroughly read the operation and function information in this manual before operating your SP-200 Series.

Application of some of the functions described in this manual are determined by the system you use. Your Maxon Dealer will program your radio so that you have the greatest number of functions possible relative to your needs.

Should you have questions regarding the operation of the radio, please consult your Maxon Dealer.

About Maxon / Topaz3

Maxon is a world-respected name in professional FM two-way radio equipment operating in the UHF, VHF and 800 MHz frequencies; personal two-way communication devices, including the popular FRS (Family Radio Service) and GMRS radios; and a variety of wireless communication products (two-way voice messaging handsets, Wireless Local Loop terminals, etc.).

Topaz3 is the exclusive supplier of Maxon products to North America.

For more specific product information: Or visit our website: www.topaz3.com

Safety Information

The Federal Communications Commission (FCC), with its action in General Docket 93-62, November 7, 1997, has adopted a safety standard for human exposure to Radio Frequency (RF) electromagnetic energy emitted by FCC regulated equipment. We subscribe to the same safety standard for the use of this product. Proper operation of this radio will result in user exposure far below the Occupational Safety and Health Act (OSHA) and Federal Communications Commission limits.

Safety Information, Continued

WARNING - DO NOT hold the radio in such a manner that the antenna is next

to, or touching, exposed parts of the body, especially the face or eyes, while transmitting.

WARNING - DO NOT allow children to operate transmitter - equipped radio

equipment.

CAUTION - DO NOT operate the radio near unshielded electrical blasting

caps or in an explosive atmosphere unless it is a type especially designed and qualified for such use.

CAUTION - DO NOT press and hold the transmit switch (P-T-T) when not

actually wishing to transmit.

NOTE: This radio operates in FCC regulated frequency bands. All radios must be licensed by the FCC before use. Because this radio contains a transmitter, Federal law prohibits unauthorized use or adjustments of this radio.

Unpacking Information

Remove and carefully inspect the contents of your package(s) for the following items:

Radio Battery Pack Battery Charger Battery Charger Power Supply Antenna Belt Clip Operating Instructions

If any items are missing, please contact the Maxon Dealer from which you purchased the radios, or contact Maxon.

SP-200 Series Features

• Synthesized operation with 199 channel capability

• 1 or 5 W programmable output power

• Programmable 12.5 /25 kHz channel spacing

• Channel scan

• Priority channel scan

• Look back channel

• CTCSS /DCS Tone signaling

• Busy channel lockout

• Time-out timer

• Scan list edit

• Priority channel edit

Description of Radio Components

Front view:

1) On/Off - Volume Control

2) LCD Channel Display

3) Busy/ TX Indicator

4) Antenna Receptacle

5) Speaker

6) Accessory Connector

7) Channel Selector Buttons

8) Monitor Button

9) Scan Button

10) Microphone

11) Push-To-Talk (P-T-T) Bar

Not shown:

Battery Battery Latch Battery Charge Contacts Belt Clip

11 10

Antenna Installation

Fasten the antenna to the radio by turning the antenna clockwise into the receptacle on top of the radio.

Installing and Removing the Battery Pack

To attach the battery pack, hold the radio face down in your hand and

position the guides of the battery in line with the radio guide rails. Slide the battery upward until a click is heard. To remove the battery pack, hold the radio face down in your hand and push the battery latch button located in the upper right hand corner of the battery pack. Hold the battery latch button down, and slide the radio battery in a downward direction. Gently lift the battery pack away from the base of radio when it is free from the radio guide rails.

Attaching and Removing the Belt Clip

To attach the clip, hold the radio face down in your hand. Locate the slot in

the belt clip and align with holder on upper left hand corner of the radio back. Push upward on belt clip until a click is heard. To remove the clip, push and hold the release button located at the top of the belt clip. Slide the clip away from the belt clip holder.

Battery Charging and Care

Before initial operation, use the provided charger to completely charge the radio battery pack. Remove the charger base and power supply from the packaging, and plug in the power supply's DC connector into a jack on the back of the charging base. Plug the AC power cord into any standard 110V AC outlet.

To charge a battery while attached to a radio, simply place the radio into the front charging well. The charger will identify the battery condition, and then automatically initiate a charge mode - rapid or top-off / trickle.

To charge a battery removed from the radio, place the battery into the rear charging well. Again, the charger will identify the battery condition, and automatically rapid charge or top-off / trickle charge the battery pack. Note the color of the LED charge indicators: red for rapid charge cycle, green for the top-off / trickle charge cycle.

Battery Charging and Care, Continued

When using both charging wells, only one can rapid charge at a time. The front charging well always has priority for rapid charging. After the front well cycles from rapid to top-off / trickle charge, the back well will initiate its rapid charge mode. Again, note the color of the charging well's LED to define the current charging cycle.

Note: To ensure peak performance from your radio, periodically discharge the battery completely and recharge fully. This action will prevent the battery from developing a "memory" of short-term use, and will permit a good service life.

SP-200 Series Operation

Power On - Volume - Power Off

Turn the radio on by rotating the off / on - volume control clockwise. You will hear a click and (if enabled via Dealer programming), the radio's self-test alert tones. Increase the radio volume by continuing the clockwise rotation. To turn the radio off when you have finished transmitting, receiving, etc., rotate the control counter-clockwise to detent.

Channel Select / Channel Group Scan

To change radio channels, simply press and release the ! or " button until the desired channel is reached. Or, to scroll through your programmed channels more quickly, press and hold the ! or " button. The channel numbers will appear in the radio's LCD (located at top of unit).

If your radio has been programmed for channel group scan, you must enter the scan mode by pressing the scan button (first button below the P-T-T bar). The current channel group will display on the radio's LCD. If you wish to change that selection, use the ! or " button, until the LCD displays the channel group you wish to scan.

To Transmit NOTE: The Federal Communications Commission Rules and Regulations

require that you monitor a channel for activity before transmitting, to avoid interrupting another user.

Press the monitor button (second button below the P-T-T bar) and check the color of the radio's top-panel LED. It will glow orange if RF activity is present;

To Transmit, Continued

it will not be illuminated if the radio indicates a "clear" channel. When the channel is "clear", hold the radio microphone area approximately 2-3 inches from your mouth, keeping the antenna vertical and away from face or eyes. Press and hold the P-T-T bar on the side of the radio, and begin speaking in a clear, normal tone. Release the P-T-T bar when you have finished speaking.

CAUTION: Operation of the transmitter without a proper antenna installed may result in permanent damage to the radio.

NOTE: The radio's LED will glow red continuously when you have the P-T-T bar pressed and are transmitting. If the red LED starts "flashing", the battery needs to be recharged and transmission will cease. Recharge the battery fully before attempting more than one transmission.

Status Indicators and Audible Alert Tones

Your SP-200 Series radio has a sophisticated microprocessor control which provides a series of audible alert tones. Upon each power-up, a quick melody* indicates that the self-test of the microprocessor functions has been completed. A series of tones may be sounded with any of the following conditions:

• Attempt to transmit on a channel set for receive only

• Attempt to transmit on a channel that is already in use when busy channel

lockout has been programmed into the radio*

• Transmitting time has exceeded time-out timer programmed length*

• Low battery condition

• Selecting a channel with no programmed frequency

* Indicates a function that is initially programmed into the radio by your Maxon Dealer.

See the Status Indicators and Audible Alert Tones chart on next page for full detail.

STATUS DESCRIPTION LED COLOR LCD INDICATION AUDIBLE TONE Normal Power On - Ready N/A 188 Melody

Call Received Orange Channel Number N/A Correct Call Green Channel Number N/ A Busy Channel Orange Channel Number N/A Transmit Red Channel Number N/A Transmit Not Allowed Red Flashing Alternating UL/ Two Beeps Repeated

Channel Number

Scanning Normal Scan Mode Green Flashing Group Number N/A

Priority Scan Mode Green Flashing N/A N/A Priority Look Back Green Flashing PS/Channel N/A

Scan Mode number Scan Edit Edit Scan List Red Single Flash SE N/A Priority Edit Priority Channel Red Two Flashes PE N/A

Edit Warning Low Battery Red Flashing LC 3 Beeps Repeated

Busy Channel Lockout Orange bL Single Beep Repeated

TX Inhibit N/A _h/rO Two Beeps

Time-Out-Timer N/A Pt Single Beep / 3 Beeps

Repeated

Error EEPROM N/A E r Single Beep Repeated

Unlock N/A UL Two Beeps Repeated

NOTE: All audible tones can be programmed "off" for silent operation.

Status Indicators and Audible Alert Tones

Scan Modes

Scanning is a Dealer programmable feature that allows you to monitor a number of channels or channels within a Group. Your Dealer will help you define a scanning mode and your channel "scan list" .

Normal Channel Scan

Once the scan list has been established, initiate scan by pressing and releasing the scan button, (first button below the P-T-T bar).

If a conversation is detected on any of the channels in the scan list, the radio will stop on that channel and you will be able to hear the conversation. If programmed for normal scan TX, you will be able to transmit on that active channel during the programmable scan delay time. (The scan delay time

Normal Channel Scan, Continued

is the amount of time the radio will stay on that channel once activity has ceased. Dealer programmable, 4 -7 seconds is typical). The radio will resume scanning once the scan delay time has expired, and will continue to scan until the channel is changed. The LED will flash green.

Priority Channel Scan

A single channel may be programmed as the "Priority" channel. The radio will constantly monitor this channel while scanning and when the radio has stopped on an active channel. If a call is detected on the priority channel, the radio will automatically move to, and remain on, the priority channel for as long as the priority conversation takes place. Priority channel activity takes precedence over all other conversations. To activate the Priority scan mode, press and release the scan button (second button below the P-T-T bar). The LED will flash green.

Other Scanning Features

Look Back

This feature is ideal for those who do not need scan as defined above, but want to make sure that they never miss a call on the "Priority" channel if another channel has been selected. Once a channel has been selected, the radio will periodically "look back" at the priority channel. If activity is detected on the priority channel, the radio will move to that channel for as long as it remains active. To enter the "look back" mode, press and hold the scan button (first button below the P-T-T bar). PS / Channel number will be shown in the display, the LED will flash green.

NOTE: Look back requires that the radio leave the current channel for a fraction of a second (at regular intervals) to check the priority channel for activity. Depending upon how the radio is programmed (scan speed, etc.) this may or may not be noticeable as "breaks" on the current channel for that same fraction of a second. A transmission will be made on the active channel at all times.

Scan Channel Delete

To temporarily delete a channel from the scan list, simply press the monitor button (second button below the P-T-T bar) while scanning and stopped on the channel to be deleted. This will remove that channel from the scan list

Scan Channel Delete, Continued

until the channel is changed or the radio's power is reset. When power is restored or the scan list channel position is selected again, the originally programmed scan list will be activated.

CTCSS / DCS Scanning

To help block out unwanted calls to your radio, the SP-200 Series can be programmed by your Dealer to scan for tones.

Normal Scan TX

Allows a transmission only after a call is received, depending on the programmed scan delay time. After scan resumes, and a transmission is made, the radio will sound two beeps, display _h and will not allow a transmission.

Priority Scan TX

Allows a transmission after a call is received depending on programmed scan delay time. The transmission will be made on the channel that the call was received. After the scan resumes, if a transmission is made, the radio will transmit on the programmed priority channel.

Priority Only TX

Allows a transmission on the priority channel when scanning and not stopped on an active channel. It will always transmit on the priority channel if scanning or stopped on an active channel.

Receive Only Scan

This allows only reception, not transmission. If a transmission is made at any time, the radio will sound two beeps, display r0 and will not allow the transmission.

Scan List Edit

You can edit your radio's original scan list and priority scan channel at any time. Please note, if your radio has been programmed for channel-only scan, you will not be able to edit your scan list, only your priority channel.

Channel Group Edit

To edit the group scan list in a radio programmed for channel group scan, turn the radio off, press and hold scan button, (first button below the P-T-T bar). While holding scan button, turn the radio on, and observe a single red flash of the LED. The display will read SE. Release the scan button.

Channel Group Edit, Continued

The first group number will be displayed. If you do not wish to edit the group you have selected press the ! or " button to select the desired channel groups you wish to edit. After channel group selection has been made, press and release the scan button, (first button below the P-T-T bar). The channel number within your selected channel group may now be edited.

If the channel number is flashing, that channel is already included in the scan list of the selected channel group. If the channel number is solid, the channel can be added or deleted from the scan list. Press and release the monitor button, (second button below the P-T-T bar), the selected channel will flash if it was added to the scan list or be solid if it was deleted from the scan list.

To edit other channels, press the ! or " buttons to select the desired channel within the channel group. To add or delete the newly selected channel from the channel group scan list, repeat the process detailed above. Upon completion of editing channels on your channel group scan list, press and release the scan button, (first button below the P-T-T bar). Your new channel group scan list should be entered at this time.

Priority Channel Edit

Only one priority channel can be programmed into the radio. To edit a priority channel, turn the radio off, press and hold scan button, (first button below the P-T-T bar). While holding the scan button, turn radio on, and release the scan button after the second red flash of the LED. PE will be shown in the display. Release the scan button. The first channel number will be displayed. If displayed channel is not your priority channel, press and release the ! or " button to select the desired priority channel.

After you have selected the channel, a flashing channel number indicates that the channel is already selected as priority. If channel number is solid, the channel is not selected as priority. To add or delete the selected channel as the priority channel, press and release the monitor button, (second button below the P-T-T bar). The selected channel will flash if it was added as a priority channel or will be solid if deleted as the priority.

Upon completion of adding or deleting the priority channel, press and release the scan button. Your new priority channel should be entered at this time.

FCC Licensing

The Federal Communications Commission requires the operator of this radio be properly licensed under the applicable Part and /or Parts of the FCC Rules and Regulations.

Consult with your Maxon Dealer, or contact the nearest FCC field office for information about obtaining a license.

Service

Do not tamper with internal adjustments. Damage to the equipment and/or improper operation may result. There are no serviceable items inside the radio. It is recommended that you return your radio to a qualified Maxon Dealer for any service or repairs.

Recycling/ Disposal of Batteries

The U.S. Environmental Protection Agency (EPA) classifies used Ni-Cd batteries as hazardous waste, unless certain exemptions apply.

The battery should be recycled at the end of its useful life. Under various state and local laws, such batteries must be recycled or disposed of properly and cannot be dumped in landfills or incinerators.

A national program to collect and recycle used Ni-Cd batteries has been implemented by the Rechargeable Battery Recycling Corporation (RBRC

). The following is a partial list of facilities where the batteries can be shipped to be recycled. Contact these facilities for proper packaging and shipping guidelines.

INMETCO Kinsbursky Brothers Inc.

245 Portersville Road 1314 N. Lemon Street Ellwood City, PA 16117 Anaheim, CA 92801 TEL: (724) 758-2800 TEL: (714) 738-8516 FAX: (724) 758-2845 (800) 548-8797

FAX: (714) 441-0857

Software Copyrights

The Maxon product(s) described in these operating instructions may include copyrighted Maxon software programs stored in semi-conductor memories or other media. Laws in the United States and other countries preserve for Maxon certain exclusive rights for copyrighted software programs, including the exclusive right to copy or reproduce in any form the copyrighted software program. Accordingly, the copyrighted Maxon software programs contained in the Maxon products described in this operating manual may not be copied or reproduced without the express written permission of Maxon. Furthermore, the purchase of Maxon products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Maxon, except for normal non-exclusive royalty free license to use that arises by operation of law in the sale of a product.

Maintenance

Your SP-200 Series radio is designed to be maintenance free. To keep your radio in good working condition, follow these cleaning instructions:

• Clean external surfaces with a clean cloth dampened in a solution of mild

dishwater detergent diluted in water. Apply the solution sparingly to avoid any moisture leaking into cracks and crevices. DO NOT submerge the radio. Use only a non-metallic brush to dislodge particles, if necessary. Dry the surface thoroughly with a soft, lint-free cloth.

• DO NOT use solvents or spirits for cleaning - they may permanently damage

the housing.

• Clean the battery and accessory port contacts with a lint-free cloth to remove

dirt, grease or foreign materials that may impede good electrical contact.

Product Warranty

Topaz3 warrants that the Products and included accessories sold herein will be free from defects in workmanship or materials under normal use and service for a period of two (2) years from the date of purchase by the original end user, provided that the buyer has complied with the requirements stated herein. This warranty is offered to the initial end user and is not assignable or transferable. Topaz3 is not responsible for any ancillary equipment which is attached to or used in conjunction with Maxon products.

If the Product fails to function under normal use because of manufacturing defect(s) or workmanship during the two (2) years period following the date of purchase, it will be replaced or repaired at Topaz3's option at no charge when returned to the place of purchase. The defective unit must be accompanied by proof of the date of purchase in the form of a sales receipt.

The sole obligation of Topaz3 hereunder shall be to replace or repair the Product covered in this Warranty. Replacement, at Topaz3's option, may include a similar or higher-featured product. Repair may include the replacement of parts or boards with functionally equivalent reconditioned or new parts or boards. Replaced parts, accessories, batteries, or boards are warranted for the balance of the original time period. All replaced parts, accessories, batteries or boards become the property of Topaz3.

Topaz3 shall have no obligation to make repairs or to cause replacement required through normal wear and tear or necessitated in whole or in part by catastrophe, fault or negligence of the user, improper or unauthorized alterations or repairs to the Product, use of the Product in a manner for which it was not designed, or by causes external to the Product. This warranty is void if the serial number is altered, defaced or removed.

The user is responsible for the payment of any charges or expenses incurred for the removal of the defective product from the vehicle or site of its use, for the transportation of the product to the place of repair, for the return of the repaired / replaced product to the site of its use and for the reinstallation of the product.

THE EXPRESS WARRANTIES CONTAINED HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES, EITHER EXPRESSED OR IMPLIED OR STATUTORY, INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

FOR ANY PRODUCT WHICH DOES NOT COMPLY WITH THE WARRANTY SPECIFIED, THE SOLE REMEDY WILL BE REPAIR OR REPLACEMENT. IN NO EVENT WILL TOPAZ3 BE LIABLE TO THE BUYER OR ITS CUSTOMERS FOR ANY DAMAGES, INCLUDING ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES, OR FOR THE LOSS OF PROFIT, REVENUE OR DATA ARISING OUT OF THE USE OF OR THE INABILITY TO USE THE PRODUCT.

This warranty is void for sales and deliveries outside of the U. S. A.

+ 40 hidden pages

Maxon SP-200 Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual