Maxmob Technology BT 01 User Manual

USER MANUAL For BT-01

Page 1

Security Precautions

In order to have a proper and safety use of the headset, please read this user manual in detail and save it.

Be sure to aware the following guidelines when using your headset.

1. Should adjust volume and time reasonably when using the headset

2. Please stop using the headset in potentially hazardous situation to ensure your safety.

3. Please avoid using headset to listen to music, make or receive calls to avoid distraction while driving.

4. Put this product and its accessories somewhere out of the reach of children, to avoid a fatal danger caused by inappropriate
use.

5. Should keep water from entering the headset during grooming, which may cause damage to the sound quality or the headset.

6. Should avoid turning the volume so high that you can’t hear anything around you. If you feel a tinnitus or the volume is too
high, please reduce the volume.

7. Stop using the headset if you feel obvious discomfort, irritation or have other adverse reactions.

8. The headset should not be stored or used at temperatures below -10℃（5 F) or above 55℃（131 F) which may shorten
headset or battery life.

Page 2

BT-01 Bluetooth sports headset in the box:

*BT-01 Bluetooth sports headset 1pc
*User’s manual 1pc
* 1pc cable slider

*Additional L&S silicon gels

Charger and battery

1. Before charging, make sure the headset has been switched off.

2. Plug USB cable into the charging port of headset; plug the other side of USB cable into the USB charger or other charging
device. Charging will start and the red light remains bright on the headset.

3. Charging time of headset takes approximately up to 1.5-2hours, red light switch off after charging completed.

Page3

Warning: Must use original cable to charge for the Bluetooth headset, otherwise it may damage the headset. Thus, voltage of
charger must be 5V, electric current exceed 100mA(5V/100mA).
This headset uses a non-detachable built-in rechargeable battery, in order to prevent damage of the headset, please do not
remove the battery.

Power on ：

Keep pressing the MF button until blue light blinks.

Pairing Mode：

Keep pressing the MF button until blue and red lights blink alternatively

Power off：

Keep pressing the MF button until red light blinks and goes out

Pair your headset with your mobile phone：

1. Keep the distance between the headset and mobile phone (or other devices need to be connected) within 1 meter. The closer,
the better .

2. Keep pressing the MF button until blue and red lights blink alternatively, enter to pairing mode.

3. Initiate Bluetooth function of mobile phone (or other device need to be connected). Then “BT01” will be shown on your
phone.。

4. Select“BT01”（ some mobile phones need you to input PIN “0000” as password） and the headset will automatically connect
with your mobile phone, the blue lights begin to blink.
Attention：Generally, there are 300 seconds at maximum to pair headset with your mobile phone, or the Bluetooth pairing

mode will stop when the lights goes out. Please retry steps 1 to 4 to pair again if your operation doesn’t work.

Page4

* Disconnect the headset with your mobile phone:

Close the Bluetooth function of your mobile phone
Or keep pressing the MF button until the red lights goes out, to switch off the headset
Or take the headset from the mobile phone to more than 10m (30ft）away.

* Reconnect the paired headset with your mobile phone:

1. Keep distance of the headset and mobile phone (or other devices need to be connected) within 1 meter, the closer, the better .

2. Switch on the headset, and the headset enters into reconnection mode when the blue light blinks.

3. Switch on the Bluetooth search function in your mobile phone or other devices need to be connected. Then the headset will
automatically reconnect with the mobile phone which has connected last time.

* Answer incoming call:

When there is an incoming call, the headset will issue a voice phrase, press the NF button once to answer the call, or use your

mobile phone to answer it.

Reject a call ：

When there is an incoming call, keep pressing the MF button for 2 times to reject the call, or use your mobile phone to reject
the call .