MAXREFDES36#
IO-Link 16-Channel Digital Input Hub
Quick Start Guide
Rev 0; 5/14
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit
patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
© 2014 Maxim Integrated Products, Inc. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
Table of Contents
1. Required Equipment ................................................................................................. 3
2. Overview ................................................................................................................... 3
3. Included Files ........................................................................................................... 5
4. Procedure ................................................................................................................. 6
5. Appendix A: Project Structure and Key Filenames ................................................. 26
6. Trademarks ............................................................................................................ 26
7. Revision History ...................................................................................................... 27
2
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
1. Required Equipment
• PC with Windows® 7 (Verify with Balluff that your version of Windows is
supported before purchasing their software.)
• MAXREFDES36# board
• One Balluff USB IO-Link® master (silver box) with corresponding USB and power
cables (This must be purchased separately.)
• Balluff IO-Link Device Tool (tested with version 2.11.1 and comes with the Balluff
USB IO-Link master)
• One IO-Link cable (yellow) (This must be purchased separately.)
• RD36_RL78_V01_XX.ZIP (Maxim-SanFrancisco-20140127-IODD1.0.1.xml),
where XX = minor version
2. Overview
Below is a high-level overview of the steps r equired to quick ly get the MAXREFDE S36#
design running by connecting it to the Balluff USB IO-Link master and Bal luff software.
Detailed instructions for each step are provided in the following pages.
1) Connect the A-to-B Type USB cable from the PC and yellow IO-Link cable to the
Balluff USB IO-Link master (silver box with part number BNI USB-901-000-A501)
as shown in Figure 1.
2) Connect the MAXREFDES36# board to the other side of the yellow IO-Link cable.
Make sure the green LED is lit as shown in Figure 2. The red and yellow LEDs do
not need to be lit.
3) Download the latest “all design files” RD36V01_XX.ZIP file located at the
MAXREFDES36# reference design page.
4) Extract the RD36V01_XX.ZIP file to a directory on your PC.
5) Install the Balluff IO-Link Device Tool.
6) Add the MAXREFDES36# digital input hub as a device into the Balluff IO -Link
Device Tool.
7) Connect to the MAXREFDES36# by pressing the online connection button.
3
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
Figure 1. MAXREFDES36# Board Connected to
a Balluff USB IO-Link Master
Figure 2. Green LED Is Lit
4
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
3. Included Files
The RD36_RL78_V01_XX.ZIP contains the corresponding IO-Link Device Descriptor
(IODD) files. The IODD contains information on communication properties, device
parameters, identification, process, and diagnostic data. It includes an XML file, an
image of the device, an icon image, and the manufacturer’s logo. The IODD st ructure is
the same for all devices of all manufacturers, and is always represented in the same
way by the IODD interpreter tools.
Figure 3. Block Diagram of System
5
4. Procedure
1. Connect the A-to-B Type USB cable from the PC and yellow IO-Link cable to
the Balluff USB IO-Link master (silver box wi th part number BNI USB-901-000A501) as shown in Figure 1.
2. Connect the MAXREFDES36# proximity sensor board to the other side of the
yellow IO-Link cable. Make sure the green LED is lit as shown in Figure 2. The
red and yellow LEDs do not need to be lit.
3. Download the latest “all design files” RD36V01_XX.ZIP file at
www.maximintegrated.com/AN5879. All files available for download are
available at the bottom of the page.
4. Extract the RD36V01_XX.ZIP file to a directory on your PC. The location is
arbitrary but the maximum path length limitation in Windows (260 character s)
should not be exceeded.
5. Install the Balluff IO-Link Device Tool. This tool comes with the pu r c hase of the
Balluff USB IO-Link master (silver box with part number BNI USB-901-000A501). Run the setup.exe file using the Run as administrator mode.
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
6
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
6. Choose the default installation folder and press the Next button.
7
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
7. Pr es s the Next button.
8
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
8. Change the language to English if applicable.
9. Close t he program by clicking the X in the top right corner.
9
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
10. Press the Close button to complete the installation.
10
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
11. Verify the version of the IO-Link Device Tool. In this case, version 2.1.11 was
used.
11
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
12. The User Login should be in Specialist mode. Password is special.
12
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
13. Import the IODD xml file for the Maxim device. In this case, the file is
Maxim-SanFrancisco-20140127-IODD1.0.1.xml and can be located in the
RD36_RL78_V01_00.ZIP file.
13
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
14. In this case, this is the IODD file shown below, but may be a different .xml file
if a different Maxim device is used.
14
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
15. See the Maxim device show up in the IO-Link devices in the Catalog window.
15
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
16. Select File | Properties.
16
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
17. After Properties is selected, the screen looks like the below screenshot.
18. Verify that the USB cable is plugged into the silver USB IO-Link Master box.
17
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
19. Drag the Balluff USB IO-Link Master to the Topology window.
18
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
20. Drag the Maxim sensor to the Name field in the Common window.
19
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
21. Verify a picture of the device shows up with the name Maxim San Francisco
Demo.
20
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
22. Press the Connect button on the Balluff IO-Link Device Tool software.
21
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
23. If your device has a problem or is unconnected, you will see the below figure.
Please check that your device is connected to the IO-Link master.
22
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
24. If you see the green Online indication on the software, the device has
connected. Click on the Maxim device icon to make t he tabs show up. Click on
the Process Data tab.
23
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
25. Connect a wire from the 24V terminal block to the INPUT terminal block (digital
input 1) as shown in the figure below.
24
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
26. Verify that the Process Data for Digital Input 1 changes to true.
25
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
5. Appendix A: Project Structure and Key Filenames
6. Trademarks
IO-Link is a registered trademark of ifm electronic GmbH.
Windows is a registered trademark and registered service mark of Microsoft Corp.
26
7. Revision History
REVISION
NUMBER
REVISION
DATE
PAGES
CHANGED
0 5/14 Initial release —
MAXREFDES36# IO-Link 16-Channel Digital Input Hub Quick Start Guide
DESCRIPTION
27
Loading...