Maxim RRFP1A-T User Manual

TM
FOOD PROCESSOR
OWNER'S MANUAL
Model RRFP1A/T
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed, including the following:
1. Read all instructions.
2. To protect against risk of electrical shock, do not put cord, plug, or appliance in water or other liquid.
3. Close supervision is necessary when any appliance is used by or near children.
4. Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning.
5. Avoid contacting moving parts.
6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Contact Consumer Service for examination, repair or electrical or mechanical adjustment.
7. The use of attachments not recommended or sold by the manufactur­er may cause fire, electric shock or injury.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter.
10. Do not let cord contact hot surface, including the stove.
11. Keep hands and utensils away from moving blades or discs while pro­cessing food to reduce the risk of severe injury to persons or damage to the Food Processor. A scraper may be used, but must be used only when the Food Processor is not running.
12. Blades are sharp. Handle carefully.
13. To reduce the risk of injury, never place cutting blade or discs on base without first putting bowl properly in place.
14. Be certain Cover is securely locked in place before operating appli­ance.
15. Never feed food by hand. Always use food pusher.
16. Do not attempt to defeat the cover interlock mechanism.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY.
2 23
Additional Important Safeguards
1. All users of this appliance must read and understand this Owner's Manual before operating or cleaning this appliance.
2. The cord to this appliance should be plugged into a 120V AC electri­cal outlet only.
3. Do not leave this appliance unattended during use.
4. If this appliance begins to malfunction during use, immediately turn the unit OFF and unplug the cord. Do not use or attempt to repair the malfunctioning appliance.
5. If this appliance falls or accidentally becomes immersed in water, unplug it immediately. Do not reach into the water! Do not use this appliance after it has fallen into or becomes immersed in water.
6. To reduce the risk of injury to persons or property, never use this appli­ance in an unstable position.
7. Do not use this appliance for other than its intended use.
Polarized Plug
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.
Electric Power
If the electrical circuit is overloaded with other appliances, your appliance may not operate. It should be operated on a separate electrical circuit from other appliances.
Plasticizer Warning
CAUTION: To prevent Plasticizers from migrating from the finish of the
countertop or tabletop or other furniture, place NON-PLASTIC coasters or placemats between the appliance and the finish of the countertop or tabletop.
Failure to do so may cause the finish to darken, permanent blem­ishes may occur or stains can appear.
322
Getting to Know Your Rachael Ray
RRFP1A/T Food Processor
1. Food Processor Power Base
2. Interlock Mechanism, Lower
3. Handle
4. Interlock Mechanism, Upper
6
5
4
5. Locking Extension
6. Food Pusher (P/N 71163)
7. Cover with Feed Chute (P/N 71162)
8. Rubber Seal Ring (P/N 71201)
9. Processing Bowl (P/N 71161)
10. Drive Shaft
11. Speed Control Dial
12. Cord
13. Cord Storage (not shown)
14. Spatula (P/N 71164)
7
3
2
1
13
4 21
10
8
9
14
11
12
Getting to Know Your
P
0FF
1
2
RRFP1A/T Attachments
1. Chopping Blade
1
2
4
3
5
6
7
8
CONTROL DIAL
with Indicator
Light
(P/N 71165) Stainless steel blade designed for cutting and kneading.
2. COARSE Shredding Blade 'C' (P/N 71167)
Stainless steel shredding blade.
3. Cheese Grating Blade 'CHEESE' (P/N 71198)
Stainless steel blade designed to finely grate fresh cheese.
4. THIN Slicing Blade 'F'
(P/N 71168) Stainless steel slicing blade.
5. THICK Slicing Blade 'C'
(P/N 71169) Stainless steel slicing blade.
6. Blade Holder
(P/N 71170) Designed to hold a Shredding or Slicing or Cheese Blade, with finger holes.
7. Blade Holder Stem (P/N
71183) Fits over Drive Shaft to support Blade Holder.
8. Storage Tray
(P/N 71199) (Shown with attachments in place) Holds 4 unused Blades and Blade Holder Stem.
P - Pulse
OFF 1 - Low Speed 2 - High Speed
5
Before First Use
WARNING: Blade Attachments are very sharp. Use extreme care when handling Blades. Failure to do so can result in personal injury.
1. Carefully unpack the Food Processor. The Storage Tray is packed with 4 Blades and the Blade Holder Stem. Wash the Processing Bowl, Cover with Feed Chute, Food Pusher, Spatula and all Attachments in warm soapy water. Rinse and dry thoroughly.
2. Wipe the Food Processor Power Base with a soft, moistened cloth. Never
immerse the Food Processor Power Base in water or any other liquid.
3. Store spare Blades and Blade Holder Stem in Storage Stand (see illustration) and keep nearby for easy accessibility.
Assembly Instructions
1. Before assembling the Food Processor ensure that the Cord is unplugged.
2. Place the Food Processor Power Base facing you on a dry, level surface.
3. Make sure the Rubber Seal Ring is in position, flat and not twisted, in the upper groove along the top of the Processing Bowl.
4. Place the Processing Bowl onto the Power Base. The Bowl will only sit cor­rectly when the handle is positioned to the left at the ten o'clock position.
5. Turn the Processing Bowl counter clockwise to engage the locking tabs and the Power Base Interlock Mechanism.
6. Determine which processing blade is to be used; Chopping, Shredding, Slicing. or Grating. If shredding, slicing or grat­ing, insert the appropriate blade into the top side of the Blade Holder, mak­ing sure it snaps in place. See illustra­tion.
Rubber
Seal Ring
6 19
Assembly Instructions (Cont.)
Note: If the Processing Bowl and the Cover are not correct­ly assembled, the Upper and Lower Safety Interlock Mechanism will not be closed and the Food Processor will not function.
7. To chop foods, fit the Chopping Blade over the Drive Shaft. To slice, shred or grate cheese, use the Blade Holder Assembly (with the proper Blade Attachment). To use the Blade Holder, first slip the Blade Holder Stem over the Drive Shaft. Using the finger holes, attach the Blade Holder (sharp cutting edge up) to the Blade Holder Stem. .
8. Place the Cover on the Processing Bowl with the lock­ing extension at approximately the nine o'clock position. Rotate the Cover counter clockwise to engage the locking tabs and the Upper Interlock Mechanism in the Processing Bowl handle.
Note: If the Lid is difficult to assemble, make sure the Rubber Seal Ring fits flat and not twist­ed, in the upper groove along the top of the Processing Bowl. Remove Ring and reattach if necessary.
Locking Extension
9. Insert the Food Pusher in the Feed Tube on the Cover.
10. Make sure the Speed Control knob is in the OFF position, then plug the Cord into a 120V AC power outlet.
11. The Food Processor is now ready to begin use.
7
Instructions for Use
Slicing, Shredding and Grating
CAUTION: Always unplug Food Processor from outlet before installing or removing attachments.
CAUTION: Use extreme care when handling the Slicing, Shredding or Grating Blades. Do not touch the cutting edges with your fingers. The cutting edges are very sharp and can cause injury if touched.
1. Make sure the unit is unplugged. Remove Storage Tray from the Processing Bowl as outlined in the BEFORE FIRST USE section of this Owner's Manual. Keep the Storage Tray out of the way, where it cannot be tipped over and make sure the Tray and all Blades are out of the reach of children. Attach the Processing Bowl to the Power Base. See ASSEMBLY INSTRUCTIONS for details.
2. Insert a Slicing, Shredding or Grating Blade into the Blade Holder. See Assembly Instructions for specific details.
3. Insert the Blade Holder and Stem in the Processing Bowl over the Drive Shaft.
4. Place the Cover on the Processing Bowl with the locking extension at approximately the nine o'clock position. Turn the Cover counter clock­wise to engage the locking tabs and the Upper Interlock Mechanism in the Processing Bowl handle.
Note: If the Lid is difficult to assemble, make sure the Rubber Seal Ring fits flat and not twisted, in the upper groove along the top of the Processing Bowl. Remove Ring and reattach if necessary.
Note: If the Processing Bowl and the Cover are not correctly assembled, the Upper and Lower Safety Interlock Mechanism will not be closed and the Food Processor will not function.
5. Make sure unit is in the OFF position; then plug the Food Processor into a 120V AC electrical outlet.
6. Remove the Food Pusher and insert the food to be processed into the Feed Chute (see Food Processing Hints for food preparation details). Turn the Speed Control Dial to desired speed; the Indicator Light will come on. Use even, constant pressure on the Food Pusher to feed food into the Feed Chute. If processing slows or seems labored, increase the Speed Control Dial from 1 to 2 or turn to OFF and select the Pulse setting. Note: Do not use excessive force or you will damage the Food Processor.
Caution: Never use fingers or other utensils to push food down the Feed Chute. Always use the Food Pusher.
8 17
Slicing, Shredding and Grating Continued
7. When finished processing, move the Speed Control Dial to OFF, the Indicator Light will go off, and unplug the unit.
Note: This Food Processor is equipped with an automatic brake that will stop the rotation of the Blade within seconds. Although this automatic brake provides an additional measure of safety, make sure that the Blade has completely stopped before you remove the Cover or unplug the unit.
8. Turn the Cover clockwise to disengage the locking tabs and lift the Cover from the Processing Bowl.
9. Carefully lift the Blade Holder Assembly from the Processing Bowl using the finger holes. Remove the Blade Holder Stem.
10. Turn the Processing Bowl handle clockwise to disengage the locking tabs and lift the bowl from the Power Base.
11. Remove contents from the Processing Bowl and the Blade Holder Assembly with the Spatula.
Chopping
CAUTION: Always unplug Food Processor from outlet before installing or removing attachments.
CAUTION: Use extreme care when handling the Chopping Blade. Do not touch the cutting edges with your fingers. The cutting edges are very sharp and can cause injury if touched.
1. Make sure the unit is unplugged. Attach the Processing Bowl to the Power Base. See Assembly Instructions for details.
2. Insert the Chopping Blade in the Processing Bowl over the Drive Shaft.
3. Place up to 7 1/2 cups of the food to be chopped into the Processing Bowl (see Food Processing Hints for food preparation details).
4. Place the Cover on the Processing Bowl with the locking extension at approximately the nine o'clock position. Turn the Cover counter clock­wise to engage the locking tabs and the Upper Interlock Mechanism in the Processing Bowl handle.
Note: If the Lid is difficult to assemble, make sure the Rubber Seal Ring fits flat and not twisted, in the upper groove along the top of the Processing Bowl. Remove Ring and reattach if necessary.
Note: If the Processing Bowl and the Cover are not correctly assembled, the Upper and Lower Safety Interlock Mechanism will not be closed and the Food Processor will not function.
916
Instructions for Use (Cont)
Chopping Continued
5. Make sure unit is in the OFF position; then plug the Food Processor into a 120V AC electrical outlet.
6. Turn the Speed Control Dial to the desired speed setting.The Indicator Light will come on. If processing slows or seems labored, increase the Speed Control Dial from 1 to 2 or turn to OFF and select the Pulse setting. Additional ingredients may be added through the Feed Chute while processing.
Caution: Never use fingers or other utensils to push food down the Feed Chute. Always use the Food Pusher.
7. When finished processing, move the Speed Control Dial to OFF, the Indicator Light will go off, and unplug the unit.
Note: This Food Processor is equipped with an automatic brake that will stop the rotation of the Blade within seconds. Although this automatic brake provides an additional measure of safety, make sure that the Blade has completely stopped before you remove the Cover or unplug the unit.
8. Turn the Cover clockwise to disengage the locking tabs and lift the Cover from the Processing Bowl.
9. Carefully lift the Chopping Blade from the Processing Bowl.
10. Turn the Processing Bowl handle clockwise to disengage the locking tabs and lift the bowl from the Power Base.
11. Remove contents from the Processing Bowl and the Chopping Blade with the Spatula.
10
Slicing, Shredding and Chopping Guide
SLICING BLADE - Cut food to fit Chute, use Speed 1
FOOD BLADE
Apple Thick Cabbage/Lettuce Thick Carrots Thick or Thin Celery Thick or Thin Cucumber Thick or Thin Mushrooms Thick or Thin Onions Thick or Thin Peppers Thick or Thin Potatoes Thick or Thin Summer Squash Thick or Thin
SHREDDING/GRATING BLADES - Cut food to fit Chute, use Speed 1
FOOD BLADE
Apple Coarse Carrots Coarse Cheese, hard
Parmesan, Romano Grating Cheese, soft or semi-soft
Cheddar, mozzarella, Swiss Coarse Summer Squash Coarse
CHOPPING BLADE - Push food from sides of bowl with spatula when necessary
FOOD
Apple Pulse Bread 1 or 2 Cabbage 1 or 2 Carrots 1 or 2 Celery Pulse Crackers 1 or 2 Eggs, hard boiled Pulse Garlic Pulse Mushrooms Pulse Onions Pulse Parsley or other Herbs 1 or 2 Peppers Pulse Potatoes Pulse Walnuts Pulse
SPEED
11
Food Processing Hints
Chopping - For best results, cut or tear food into pieces approxi-
mately equal in size before processing. The finished results will be more uniform. Consistent processing results are achieved if the con­tainer has 2 to 7 1/2 cups of fruits or vegetables.
Mincing - Pre-cooked meat into cubes approximately 1-inch square.
Fruits and Vegetables - Before processing fruits and vegetables,
clean and cut into 1-inch pieces.
Mixing - Quantities that can be processed within the Processing Bowl
will vary depending upon the density of the ingredients being used.
Adding Ingredients - Liquid ingredients may be added while the
processor is operating by pouring through the Feed Tube in the Cover.
Using the Feed Tube - The most important factor for successful slic-
ing and shredding is the way in which the food is packed into the Feed Tube. The Feed Tube should always be packed firmly to allow each piece of food to support the others. There will always be a small portion of food left unprocessed between the Food Pusher and the Blade.
Caution: Never use fingers or other utensils to push food down the Feed Chute. Always use the Food Pusher.
Slicing, Shredding and Grating - Cut all ingredients to a size that
fits comfortably into the Feed Tube. Pack the Feed Tube and, while holding food steady and upright with the Food Pusher, press down evenly until all ingredients are sliced or shredded. Do not use exces­sive force or you may damage the Food Processor.
Long Slices: Pack food items horizontally in Feed Tube.
Short Slices: Pack food items vertically in Feed Tube.
Grating: For best results remember that softer foods such as cheese
(Cheddar, mozzarella or Swiss) should be well chilled before process­ing. Harder foods such as Parmesan or Romano cheese should be at room temperature before processing. Note: When grating Parmesan cheese do not apply excessive pressure to the Food Pusher.
12
User Maintenance Instructions
This appliance requires little maintenance. It contains no user-serviceable parts. Any servicing requiring disassembly must be performed by a quali­fied appliance repair technician.
Cleaning Instructions
CAUTION: The Blades are sharp! Handle with care! Use extreme care when handling the Blades. Do not touch the Blades with your fingers. The Blades are very sharp and can cause injury if touched.
CAUTION: Never place Processor Power Base in water or any other liquid.
1. Always unplug the unit before cleaning. Make sure the Chopping
Blade or Blade Holder Assembly has completely stopped before any disassembly.
2. Remove all attachments.
3. Wash the Processor Bowl with Rubber Seal Ring, Lid with Feed
Chute, Food Pusher, Blade Holder, Blade Holder Stem, Slicing/Shredding/Grating Blades, Chopping Blade and Spatula in warm soapy water. Removable parts may also be cleaned in the dish­washer. Load parts on the top rack away from the dishwasher heating coil.
4. Never immerse the Processor Power Base in water or any
other liquid. If necessary, wipe exterior surface with a soft, damp cloth or sponge and dry thoroughly.
Storage Instructions
1. Pack the Storage Tray. Fit the Blade
Holder Stem down into the recessed area of the Tray. The unused Blades fit easily into any of the 4 storage areas (see illustration).
2. Make sure the Rubber Seal Ring fits
flat and not twisted, in the upper groove along the top of the Processing Bowl. Place the Processing Bowl in position on the Power Base. Grasping the Storage Trays cen­ter hub, lower the packed Storage Tray into the Bowl. Replace the Lid and lock before storing.
3. Push the cord into the Cord Storage area located on the underside of
the appliance. Never wrap the cord around the appliance. The appli­ance should be stored in a clean, dry place.
13
Storage Tray with Attachments
Recipes (Cont.)
This recipe has been specially
TM
created by Rachael Ray for this appliance.
BASIL-TARRAGON PESTO
For 2 pounds of pasta, such as fettuccine
2 bunches, about 2 cups, fresh basil leaves 1/2 cup tarragon leaves stripped from stems, about 5 - 6 sprigs 4 small cloves of garlic, popped from skins 6 tablespoons pine nuts, a handful 1/4 pound, about 1 cup, grated Parmigiano Reggiano cheese, a couple
handfuls
The zest of 2 lemons 2 splashes of water, about 2 tablespoons 1/2 cup EVOO - extra virgin olive oil, eyeball it Coarse salt and fresh black pepper, to your taste
Place the basil, tarragon, garlic, pine nuts, cheese and lemon juice in processor and pulse grind to a fine chop. Add a couple splashes of water and turn processor on. Stream the EVOO into the processor to form a thick sauce. Season sauce with salt and pepper to taste and scrape into a large shallow serving bowl.
Cook the pasta in salted boiling water. Drain pasta and add hot pasta to sauce. Toss to coat evenly and adjust seasoning. Serve immediately.
Yield: 8 servings or 1 1/4 cups
14
This recipe has been specially
TM
created by Rachael Ray for this appliance.
CLASSIC BASIL, PARSLEY AND SPINACH-WALNUT PESTOS
Each pesto recipe will provide enough sauce for 2 pounds of pasta, or freeze some and have it next week.
Method for each recipe:
•Toast pine nuts (pignoli), walnuts or sesame seeds until golden brown
before using them. (Buy nuts a handful at a time from the bulk bins.)
•Heat oil and garlic in small pan on low heat or in microwave, 30 sec-
onds on high, before using.
• Pulse all ingredients in processor until paste forms.
• Serve over hot pasta, but never heat the pestos themselves. Pestos
should be used at room temperature.
CLASSIC BASIL PESTO
1 cup EVOO - extra virgin olive oil 4 cloves garlic, popped from skin and cut in half 1/2 pound, about 2 3/4 cups, grated Parmigiano Reggiano cheese,
a couple of handfuls 6 ounces pine nuts (a handful) 2 bunches basil, about 80 to 100 leaves or 2 cups
PARSLEY PESTO
1 cup EVOO - extra virgin olive oil 4 cloves garlic, popped from skin and cut in half 1/2 pound, about 2 3/4 cups, grated Parmigiano Reggiano or Romano
cheese, a couple of handfuls 6 ounces walnut pieces (a handful) 2 bunches fresh flat-leaf parsley, tops ripped away from stems
SPINACH-WALNUT PESTO
1 cup EVOO - extra virgin olive oil 4 cloves garlic, popped from skin and cut in half 2 cups fresh spinach leaves, packed down, or 1 cup drained, defrosted
frozen chopped spinach 6 ounces walnut pieces (a handful) 4 pinches ground nutmeg 1/2 pound, about 2 3/4 cups, grated Parmigiano Reggiano or Romano
cheese, a couple of handfuls
15
Recipes (Cont.)
This recipe has been specially
TM
created by Rachael Ray for this appliance.
TEX-MEX WHITE BEAN DIP
3 cans (14 ounces) white kidney or cannelloni beans, drained 3 cloves garlic, popped away from skin 6-9 tablespoons fresh cilantro, a couple of handfuls of leaves 4 1/2 teaspoons ground cumin, a palm full 2 tablespoons hot sauce, such as Tabasco®, eyeball it 3 splashes of water, about 3 tablespoons Coarse salt and fresh black pepper, to your taste Corn tortilla chips, yellow or blue, any variety and salsa of your choice
Place the beans, garlic, cilantro, cumin, and Tabasco®in processor. Process the beans until smooth on speed 2. If dip is too thick, add water a splash at a time and reprocess. Season the dip with salt and pepper to taste. Serve with chips and salsa.
Yield: 3 1/2 cups
MUFFALETTA SANDWICH RELISH
Spread this on your favorite sub or Italian sandwich - WOW!
20 large pitted green olives with pimientos, drained about 1 cup 1 (16 ounce) jar, Giardiniera, Italian pickled vegetable salad, drained
(Giardiniera is a pickled veggie mixture of cauliflower, carrots, celery and
hot peppers)
A handful of flat-leaf parsley leaves A handful of fresh basil leaves The zest of 1 lemon and juice of 1/2 lemon
Place all the ingredients in processor and Pulse to form a finely chopped relish. Transfer to a small container and keep on hand for spreading on your favorite sandwiches.
Yield: 2 cups
This recipe has been specially
TM
created by Rachael Ray for this appliance.
ITALIAN ROASTED RED PEPPER HUMMUS
2 (14 ounces) cans chick peas (garbanzo beans), drained 4 roasted red peppers, or 1 (15 ounce) jar roasted bell peppers, drain and
pat dry 2 sprigs fresh rosemary leaves stripped from stems 2 cloves garlic, cracked away from skin 4 pinches of crushed red pepper flakes 2 splashes of water, about 2 tablespoons 4-6 tablespoons EVOO - extra virgin olive oil, eyeball it Salt and pepper, to taste Specialty potato chips, sesame melba rounds, or toasted bread rounds
for dipping
Place chick peas, red peppers, rosemary, garlic, and red pepper flakes in processor and grind on Speed 2 into a thick paste. Add water a splash at a time and reprocess. While processor is on, stream in EVOO to form a smooth dip. Season the dip with salt and pepper, to your taste. Transfer dip to a small bowl and serve with dippers of choice.
Yield: 4 cups
Recipes (Cont.)
This recipe has been specially
TM
created by Rachael Ray for this appliance.
GREEN WRAPS WITH WHITE BEAN HUMMUS
2 (15 ounce) cans cannelloni beans, drained and rinsed 4 stems fresh rosemary, leaves stripped from stem 2 cloves garlic, popped from skin 3-4 tablespoons EVOO - extra virgin olive oil, eyeball it Black pepper, to your taste
4 firm vine-ripened tomatoes, thinly sliced 1/2 seedless cucumber, thinly sliced 1/2 red onion, thinly sliced A couple handfuls pitted Kalamata olives A couple of handfuls chopped fresh flat-leaf parsley 1/2 pound mixed greens 2 lemons EVOO - extra virgin olive oil Coarse salt, to taste 1/2 pound feta cheese, crumbled
8 large pita breads, or flour tortilla wraps, or flavored wraps
Combine beans, rosemary, garlic, EVOO, and black pepper in processor. Pulse until mixture is smooth.
Combine tomatoes, cucumber, onion, olives, parsley, greens, and the juice of lemons in a bowl. Drizzle with olive oil, and sprinkle with salt. Combine well.
Warm pitas or wraps in microwave oven or on a griddle pan. Spread with a generous dose of white bean hummus. Top with a layer of Greek salad mixture. Sprinkle with Feta cheese crumbles and roll. Wrap lower half of wraps with foil or waxed paper to keep it together while you eat your way down. Keep a paper towel in your hand as you eat to catch any drips. Batches of white bean spread are also a terrific dip for specialty chips, celery, or bread sticks.
Yield: 8 wraps
18
SPINACH DIP
1 (10 ounce) package, defrosted frozen chopped spinach 1 (8-ounce) can sliced water chestnuts, drained 2 cloves garlic 1 cup plain yogurt 2 bunches green onions, cut in 1-inch pieces 1 cup sour cream 2 teaspoons salt 1 teaspoon dried tarragon leaves 1/2 teaspoon dry mustard 1/2 teaspoon pepper
Place all of the ingredients into the Food Processor with the Chopping Blade. Chop on Speed 2 until blended. Remove from the Bowl, cover and refrigerate for 2 hours to enhance flavor.
Yield: 4 cups
CRAB DIP
1 (8 ounce) container lump crab meat 1 medium cucumber peeled, cut in half and seeded, cut in 1-inch pieces 11 ounces cream cheese, softened 1/3 cup mayonnaise 2 teaspoons chili sauce 2 teaspoons Worcestershire sauce 1/8 teaspoon sugar 3/4 teaspoon Old Bay seasoning Salt and pepper to taste
Add all ingredients to the Food Processor with the Chopping Blade. Pulse until ingredients are chopped and mixed. Remove from the Bowl, cover and refrigerate for 2 hours to enhance flavor.
Yield: 4 cups
PIMENTO CHEESE SPREAD
1 (16 ounces) block Cheddar cheese 1 (4 ounce) jar pimentos, drained 2 cups salad dressing
Use the Coarse Shredding Blade to shred the cheese then remove from the bowl. Place the Chopping Blade into the Bowl and add the pimentos, salad dressing and cheese. Process the mixture on Speed 1 until blend­ed. Remove from the Bowl, cover and refrigerate for 2 hours.
Yield: 4 cups
Recipes (Cont.)
P
0FF
1
2
FRESH SALSA
10 Roma tomatoes, quartered and seeds removed 1 medium jalapeno pepper, halved and seeds removed 1 large onion, cut into 1-inch cubes 1/2 cup packed fresh cilantro leaves stripped from the stems 1 teaspoon cider vinegar 1 teaspoon salt 1/2 teaspoon black pepper
Place all of the ingredients into the Food Processor with the Chopping Blade. Pulse until coarsely chopped. Remove from the Bowl, cover and refrigerate for 2 hours.
Yield: 3 cups
PEANUT BUTTER
12 ounces cocktail party peanuts 3 tablespoons honey 1/2 teaspoon cinnamon
Place all of the ingredients into the Food Processor with the Chopping Blade. Chop on Speed 2 until smooth. Remove from the Bowl and serve. Store in the refrigerator to keep fresh.
Yield: 1 1/2 cups
20
BRUSCHETTA
Topping:
8 Roma tomatoes, quartered and seeds removed 1/4 cup packed fresh basil leaves, about 15 1/2 medium onion, cut into 1 inch cubes 3 cloves garlic 2 tablespoons olive oil 1 teaspoon red wine vinegar 1/2 teaspoon salt 1/4 teaspoon black pepper
Bread:
1 loaf French Baguette or crusty Italian bread cut diagonally in 1/2 inch
slices 2 teaspoons garlic salt 3/4 cup olive oil
Place all of the topping ingredients into the Food Processor with the Chopping Blade. Pulse until coarsely chopped. Remove from the Bowl to serve on warm grilled bread.
Mix together olive oil and garlic salt. Brush both sides of the sliced bread with the oil mixture. Lightly brown both sides of the bread. Top warm bread with Bruschetta and serve.
Yield: 3 cups bruschetta
Recipes (Cont.)
MEATBALLS
1 pound tenderized stew meat 1 slice bread, tear in 1-inch pieces 1 small onion, cut in 1-inch pieces 1 clove garlic 1 egg 1/2 teaspoon dried thyme Salt and pepper to taste 1/2 cup all-purpose flour
Place all of the ingredients, except flour, into the Food Processor with the Chopping Blade. Chop on Speed 2 until meat is ground and ingredients are mixed together. DO NOT over process.
Shape into 2-inch meatballs and coat with flour. Heat oil in skillet and cook meatballs until done.
Yield: 12 meatballs
MACARONI SALAD
3 cups uncooked elbow macaroni 1 tablespoon vegetable oil 1/2 onion, cut in 1-inch cubes 2 stalks celery, cut in 1-inch pieces 1 carrot, cut in 1-inch pieces 1/2 green pepper, cut in 1-inch pieces 3 hard-boiled eggs, cut in half
DRESSING:
1 1/3 cups sugar 1/2 cup vinegar 2 eggs 1 1/2 teaspoons salt 1 cup salad dressing 1 1/2 teaspoons prepared mustard 1 (5 1/3-ounce) can evaporated milk
Cook macaroni, drain and stir in oil. Place the onion, celery, carrot, green pepper and hard-boiled eggs into the Food Processor with the Chopping Blade. Pulse the food until coarsely chopped, stir into the cooked maca­roni.
To make dressing, combine sugar, vinegar, eggs and salt. Bring to a boil over medium heat, stirring frequently. Cool and stir in rest of dressing ingredients. Pour over macaroni mixture, refrigerate several hours.
Yield: 12 servings
LIMITED ONE-YEAR WARRANTY
Warranty Coverage: This product is warranted to be free from defects in materials
or workmanship for a period of one (1) year from the original purchase date. This product warranty is extended only to the original consumer purchaser of the prod­uct and is not transferable. For a period of one (1) year from the date of original purchase of the product, our Repair Center will, at its option, either (1) repair the product or (2) replace the product with a reconditioned comparable model. These remedies are the purchaser's exclusive remedies under this warranty.
Warranty Service: To obtain warranty service, you must call our warranty service number at 1-800-233-9054 for return instructions on how to deliver the product, in either the original packaging or packaging affording an equal degree of protection to the Repair Center specified below. You must enclose a copy of your sales receipt or other proof of purchase to demonstrate eligibility for warranty cover­age.
To return the appliance, ship to: To contact us, please write to, call, or email:
ATTN: Repair Center Consumer Relations Department 708 South Missouri Street PO Box 7366 Macon, MO 63552 USA Columbia MO 65205-7366 USA
1-800-233-9054 E-mail: consumer_relations@toastmaster.com
What Is Not Covered: This warranty does not cover damage resulting from mis­use, accident, commercial use, improper service or any other damage caused by anything other than defects in material or workmanship during ordinary consumer use. This warranty is invalid if the serial number has been altered or removed from the product. This warranty is valid only in the United States and Canada.
LIMITATION ON DAMAGES: THERE SHALL BE NO LIABILITY FOR ANY INCIDEN­TAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY OR CONDITION ON THIS PRODUCT.
DURATION OF IMPLIED WARRANTIES: EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES AND CONDITIONS, INCLUDING, WITHOUT LIMITATION, IMPLIED WARRANTIES AND CONDITIONS OF MER­CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE OR USE ON THIS PRODUCT ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
Some jurisdictions do not allow the exclusion or limitation of incidental or conse­quential damages, or allow limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights under the laws of your jurisdic­tion.
For more information on our products, visit our website: www.maxim-toastmaster.com
Hope you love using this and the other kitchen appliances in my line. I love to cook – as long as it's fast, fun and simple! These cool kitchen helpers will make it easy to cook a great meal – from start to finish – in 30 minutes. And they'll look awesome on your counter!
Rachael Ray
All recipes (so indicated) Copyright © 2006, by Rachael Ray. All Rights Reserved. Used by Permission.
Printed in China 5/06 © 2006 Maxim®/Toastmaster®Inc. P/N 61721A
Loading...