General Description
The MAX6469–MAX6484 are low-dropout linear regulators with a fully integrated microprocessor reset circuit.
Each is available with preset output voltages from +1.5V
to +3.3V in 100mV increments and delivers up to 300mA
of load current. These devices consume only 82µA of
supply current. The low supply current, low dropout voltage, and integrated reset functionality make these
devices ideal for battery-powered portable equipment.
The MAX6469–MAX6484 include a reset output that indicates when the regulator output drops below standard
microprocessor supply tolerances (-7.5% or -12.5% of
nominal output voltage). This eliminates the need for an
external microprocessor supervisor, while ensuring that
supply voltages and clock oscillators have stabilized
before processor activity is enabled. Push-pull and opendrain active-low reset outputs are available, with reset
timeout periods of 2.5ms, 20ms, 150ms, or 1200ms (min).
The MAX6469/MAX6470/MAX6473–MAX6478/MAX6481–
MAX6484 also have a shutdown feature that reduces the
supply current to 0.1µA (typ). The MAX6471–MAX6474/
MAX6479–MAX6482 offer a manual reset input to assert a
microprocessor reset while the regulator output is within
specification. The MAX6475/MAX6476/MAX6483/
MAX6484 feature a remote feedback sense pin for use
with an external NPN transistor for higher-current applications. The MAX6469–MAX6476 are available in 6-pin
SOT23 and 8-pin thin QFN packages. The MAX6477–
MAX6484 are available in a 3 × 3 chip-scale package
(UCSP™). All devices are specified for operation from
-40°C to +85°C.
Applications
Hand-Held Instruments (PDAs, Palmtops)
PCMCIA Cards/USB Devices
Cellular/Cordless Telephones
CD/DVD Drives
Notebook Computers
Digital Cameras
Bluetooth Modules/Wireless LAN
Features
♦ 3 ✕ 3 UCSP, 6-Pin SOT23, and 8-Pin QFN Packages
♦ Preset +1.5V to +3.3V Output (100mV Increments)
♦ SET Pin for Adjustable Output Voltage
♦ 75µV
RMS
LDO Output Voltage Noise
(MAX6477–MAX6484)
♦ ±2.0% Accuracy Over Temperature
♦ Guaranteed 300mA Output Current
♦ Low Dropout Voltage
55mV at 150mA
114mV at 300mA
♦ 82µA Supply Current, 0.1µA Shutdown Current
♦ Input Reverse Current, Thermal and Short-Circuit
Protection
♦ Microprocessor Reset with Four Timeout Options
♦ Push-Pull or Open-Drain RESET
♦ Manual Reset Input
♦ Remote Feedback Sense
MAX6469–MAX6484
300mA LDO Linear Regulators with
Internal Microprocessor Reset Circuit
________________________________________________________________ Maxim Integrated Products 1
Ordering Information
19-2532; Rev 2; 6/03
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Note: The first “_ _”are placeholders for the output voltage levels
of the devices. Desired output voltages are set by the suffix found
in the Output Voltage Suffix Guide (Table 1). The third “_” is a
placeholder for the reset threshold accuracy. Desired reset
threshold accuracy is set by the suffix found in the Reset
Threshold Accuracy Guide (Table 2). The “_” following the D is a
placeholder for the reset timeout delay time. Desired reset timeout
delay time is set by the suffix found in the Reset Timeout Delay
Guide (Table 3). For example, the MAX6481BL30BD4-T has a
3.0V output voltage, 12.5% reset threshold tolerance, and a
1200ms (min) reset timeout delay. Sample stock is generally available on standard versions only (Table 4). Standard versions
require a minimum order increment of 2.5k units. Nonstandard
versions must be ordered in 10k-unit increments. Contact factory
for availability.
Ordering Information continued at end of data sheet.
Pin Configurations appear at end of data sheet.
Typical Operating Circuits appear at end of data sheet.
UCSP is a trademark of Maxim Integrated Products, Inc.
*Future product—contact factory for availability.
EVALUATION KIT
AVAILABLE
MAX6469UT_ _ _D_-T -40°C to +85°C 6 SOT23-6
MAX6469TA_ _ _D_* -40°C to +85°C 8 Thin QFN
MAX6470UT_ _ _D_-T -40°C to +85°C 6 SOT23-6
MAX6470TA_ _ _D_* -40°C to +85°C 8 Thin QFN
PART TEMP RANGE
PINPACKAGE
MAX6469–MAX6484
300mA LDO Linear Regulators with Internal
Microprocessor Reset Circuit
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
(All voltages referenced to GND, unless otherwise noted.)
IN, SHDN, OUT, FB ..................................................-0.3V to +7V
MR, SET .......................................................-0.3V to (V
IN
+ 0.3V)
RESET (push-pull) ...................................-0.3V to (V
OUT
+ 0.3V)
RESET (open drain)..................................................-0.3V to +7V
OUT Short Circuit .......................................................Continuous
Input/Output Current (all pins except IN and OUT) ............20mA
Continuous Power Dissipation (T
A
= +70°C)
3 x 3 UCSP (derate 10.5mW/°C above +70°C) ............840mW
6-Pin SOT23 (derate 9.1mW/°C above +70°C).............727mW
8-Pin Thin QFN
(derate 24.4mW/°C above +70°C)..............................1951mW
Operating Temperature Range ..........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
ELECTRICAL CHARACTERISTICS
(VIN= (V
OUT
+ 0.5V) or +2.5V, whichever is greater, C
OUT
= 3.3µF, TA= -40°C to +85°C. Typical specifications are at TA= +25°C,
unless otherwise noted.) (Note 2)
Dual Mode is a trademark of Maxim Integrated Products, Inc.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Note 1: The MAX6477–MAX6484 are constructed using a unique set of packaging techniques that impose a limit on the thermal pro-
file the devices can be exposed to during board-level solder attach and rework. This limit permits only the use of the solder
profiles recommended in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and
Convection reflow. Pre-heating is required. Hand or wave soldering is not allowed.
Input Voltage Range V
Input Undervoltage Lockout V
Supply Current (Ground Current) I
Shutdown Supply Current I
REGULATOR CIRCUIT
Output Current 300 mA
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6469–MAX6476
Output Voltage Accuracy (Fixed
Output Voltage Operation,
Table 1) MAX6477–MAX6484
Adjustable Output Voltage Range V
SET Reference Voltage V
SET Dual ModeTM Threshold 185 mV
SET Input Leakage Current I
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
IN
UVLO
Q
SHDN
SET
SET
VIN falling 2.25 2.47 V
I
= 0 82 136
OUT
I
= 300mA 96
OUT
TA = +25°C 0.1 1 µA
1mA ≤ I
OUT
1mA ≤ I
OUT
1mA ≤ I
OUT
2mA ≤ I
OUT
2mA ≤ I
OUT
2mA ≤ I
OUT
(Note 3)
V
= 0, +1.2V (Note 3) ±20 ±100 nA
SET
≤ 150mA, TA = +25°C -1.3 +1.3
≤ 150mA, TA = -40°C to +85°C -2.3 +2.3
≤ 300mA, TA = -40°C to +85°C -2.7 +2.7
≤ 100mA, TA = +25°C -1.1 +1.1
≤ 100mA, TA = -40°C to +85°C -2.0 +2.0
≤ 300mA, TA = -40°C to +85°C
2.5 5.5 V
-2.5 +2.5
SET
1.200 1.229 1.258 V
5.0 V
µA
%
%
MAX6469–MAX6484
300mA LDO Linear Regulators with Internal
Microprocessor Reset Circuit
_______________________________________________________________________________________ 3
ELECTRICAL CHARACTERISTICS (continued)
(VIN= (V
OUT
+ 0.5V) or +2.5V, whichever is greater, C
OUT
= 3.3µF, TA= -40°C to +85°C. Typical specifications are at TA= +25°C,
unless otherwise noted.) (Note 2)
Dropout Voltage
(Notes 3, 4)
Output Current Limit VIN ≥ 2.5V (Note 3) 450 mA
Input Reverse Leakage Current
(OUT to IN Leakage Current)
Startup Time Response
SHDN Input Low Voltage V
SHDN Input High Voltage V
SHDN Input Current SHDN = VIN or GND -1 0.1 +1 µA
Thermal-Shutdown Temperature T
Thermal-Shutdown Hysteresis ∆T
Line Regulation
Load Regulation
Output Voltage Noise
RESET CIRCUIT
V
OUT
(V
FB
MAX6483/MAX6484) (Note 5)
V
OUT
(V
FB
MAX6483/MAX6484)
Reset Timeout Period
(Note 6)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
I
= 50mA 23 32
OUT
I
= 150mA 55 90
OUT
I
= 300mA 114 180
OUT
I
= 50mA 25 40
OUT
I
= 150mA 61 100
OUT
I
= 300mA 114 190
OUT
I
= 50mA 26 50
OUT
I
= 150mA 65 110
OUT
I
= 300mA 137 210
OUT
I
= 50mA 30 60
OUT
I
= 150mA 75 150
OUT
I
= 300mA 158 250
OUT
OUT
20 µs
0.7 × V
IN
180 °C
20 °C
0.09 %/V
≤
OUT
0.2 %
MAX6469–MAX6476 150
MAX6477–MAX6484 75
0.3 × V
Reset Threshold
for MAX6475/MAX6476/
∆V
SHDN
SHDN
V
THOUT
V
= +3.3V
OUT
(fixed output operation)
V
= +3.0V
OUT
(fixed output operation)
DO
V
= +2.8V
OUT
(fixed output operation)
V
= +2.5V
OUT
(fixed output operation)
= 4V, V
V
IN
Rising edge of V
= 5.5V, SHDN deasserted 0.01 1.5 µA
OUT
or SHDN to V
IN
within specification, RL = 68Ω, SET = GND,
= 10mA
I
OUT
IL
IH
V
= 1.5V, 2.5V ≤ VIN ≤ 5.5V,
OUT
= 10mA
I
OUT
V
= 1.5V, VIN = 2.5V, 1mA ≤ I
OUT
150mA
10Hz to 100kHz,
C
= 0.1µF,
IN
= 100mA,
I
OUT
V
= 1.5V
OUT
MAX64_ _ _ _ _ _ A 90 92.5 95
MAX64_ _ _ _ _ _ B 85 87.5 90
to Reset Delay
for MAX6475/MAX6476/
35 µs
D1 2.5 3.75 5.0
t
RP
D2 20 30 40
D3 150 225 300
D4 1200 1800 2400
IN
µV
%V
mV
V
V
RMS
OUT
ms
MAX6469–MAX6484
300mA LDO Linear Regulators with Internal
Microprocessor Reset Circuit
4 _______________________________________________________________________________________
Note 2: All devices are 100% production tested at +25°C and are guaranteed by correlation for TA= T
MIN
to T
MAX
.
Note 3: Guaranteed by design.
Note 4: Dropout voltage is defined as (V
IN
- V
OUT
) when V
OUT
is 2% below the value of V
OUT
for VIN= V
OUT(NOM)
+ 1V.
Note 5: MAX6473/MAX6474/MAX6481/MAX6482 are guaranteed by design for V
OUT
< 2.5V.
Note 6: Select the reset timeout period using the Reset Timeout Delay Guide (Table 3). Insert the appropriate suffix in the part number
when ordering.
ELECTRICAL CHARACTERISTICS (continued)
(VIN= (V
OUT
+ 0.5V) or +2.5V, whichever is greater, C
OUT
= 3.3µF, TA= -40°C to +85°C. Typical specifications are at TA= +25°C,
unless otherwise noted.) (Note 2)
Typical Operating Characteristics
(VIN= 5V, V
OUT
= 3.3V, C
OUT
= 3.3µF, TA= +25°C, unless otherwise noted.)
MR Input Low Voltage V
MR Input High Voltage V
MR Minimum Input Pulse 1µs
MR Glitch Rejection 120 ns
MR to Reset Delay 200 ns
MR Pullup Resistance MR to OUT 25 40 70 kΩ
RESET Output Voltage
(Open Drain)
Open-Drain Reset Output
Leakage Current
RESET Output Voltage Push-Pull
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
0.3 ×
V
OUT
1µA
V
I
LKG
V
V
IL
IH
OL
OL
OH
(Note 3)
V
≥ 1.0V, I
OUT
V
≥ 1.5V , I
OU T
(Note 3)
V
≥ 1.0V, I
OUT
V
≥ 1.5V , I
OU T
V
≥ 2.0V, I
OUT
deasserted
0.7 ×
V
OUT
= 50µA, RESET asserted 0.3
SINK
= 3.2m A, RES ET asser ted 0.4
S IN K
= 50µA, RESET asserted 0.3
SINK
= 3.2m A, RES ET asser ted 0.4
S IN K
SOURCE
= 500µA, RESET
0.8 ×
V
OUT
V
V
V
V
GROUND CURRENT vs. INPUT VOLTAGE
120
100
80
60
40
GROUND CURRENT (µA)
20
0
06
INPUT VOLTAGE (V)
(NO LOAD)
+85°C
+25°C
-40°C
GROUND CURRENT vs. INPUT VOLTAGE
(300mA LOAD)
120
100
MAX6469 toc01
80
60
40
GROUND CURRENT (µA)
20
54321
0
+85°C
+25°C
-40°C
INPUT VOLTAGE (V)
MAXIMUM TRANSIENT DURATION
vs. RESET THRESHOLD OVERDRIVE
150
125
MAX6469 toc02
PULSE DURATION (µs)
5432106
RESET ASSERTS ABOVE
THIS LINE
100
75
50
25
0
1 100
RESET THRESHOLD OVERDRIVE (mV)
10
MAX6469 toc03
MAX6469–MAX6484
300mA LDO Linear Regulators with Internal
Microprocessor Reset Circuit
_______________________________________________________________________________________ 5
Typical Operating Characteristics (continued)
(VIN= 5V, V
OUT
= 3.3V, C
OUT
= 3.3µF, TA= +25°C, unless otherwise noted.)
DROPOUT VOLTAGE vs. LOAD CURRENT
125
V
= 3.3V
OUT
= 3.3µF
C
OUT
100
75
50
DROPOUT VOLTAGE (mV)
25
0
0 300
LOAD CURRENT (mA)
OUTPUT NOISE
VIN = 4.5V
= 3.3V
V
OUT
= 100mA
I
LOAD
PSRR vs. FREQUENCY
V
= 3.3V
OUT
= 3.3µF
C
OUT
= 30mA
I
LOAD
OUTPUT NOISE vs. FREQUENCY
VIN = 2.5V
= 1.5V
V
OUT
= 100mA
I
OUT
25020015010050
MAX6469 toc07
MAX6469 toc04
100µV/div
0
-10
-20
-30
PSRR (dB)
-40
-50
-60
0.01 1000
100
80
60
(µV)
RMS
V
40
20
FREQUENCY (kHz)
REGION OF STABLE C
vs. LOAD CURRENT
5
MAX6469 toc05
4
3
ESR (Ω)
OUT
2
C
1
0
1001010.1
0300
C
C
OUT
STABLE REGION
LOAD CURRENT (mA)
OUT
= 4.7µF
= 3.3µF
SHUTDOWN RESPONSE
MAX6469 toc08
I
= 50mA
LOAD
OUT
ESR
25020015010050
MAX6469 toc09
MAX6469 toc06
V
SHDN
5V/div
V
OUT
2V/div
500µs/div
0
10 100 10k 100k
1k
FREQUENCY (Hz)
20ms/div
LOAD-TRANSIENT RESPONSE
STARTUP RESPONSE
10µs/div
MAX6469 toc10
V
IN
2V/div
V
OUT
2V/div
LOAD-TRANSIENT RESPONSE
100µs/div
MAX6469 toc11
V
OUT
20mV/div
NEAR DROPOUT
10µs/div
V
IN
V
OUT
I
LOAD
MAX6469 toc12
= 5V
= 3.3V
= 100mA
V
OUT
5mV/div
MAX6469–MAX6484
300mA LDO Linear Regulators with Internal
Microprocessor Reset Circuit
6 _______________________________________________________________________________________
Typical Operating Characteristics (continued)
(VIN= 5V, V
OUT
= 3.3V, C
OUT
= 3.3µF, TA= +25°C, unless otherwise noted.)
V
OUT
I
LOAD
LINE TRANSIENT RESPONSE
= 3.3V
= 10mA
100µs/div
MAX6469 toc13
5V
V
IN
500mV/div
4.5V
V
OUT
20mV/div
AC-COUPLED
RESET DELAY RESPONSE
200ms/div
MAX6469 toc14
V
IN
1V TO 4V
2V/div
RESET
2V/div
RESET RESPONSE TO MR
200ns/div
MAX6469 toc15
MR
2V/div
RESET
2V/div
RESET RESPONSE TO VIN RISING
200ms/div
MAX6469 toc16
RESET
2V/div
V
OUT
2V/div
V
IN
5V/div
NORMALIZED OUTPUT VOLTAGE
vs. TEMPERATURE
1.012
NORMALIZED TO +25°C
1.006
I
= 10mA
LOAD
1.000
I
= 300mA
I
= 150mA
LOAD
0.994
NORMALIZED OUTPUT VOLTAGE
0.988
-40 85
LOAD
TEMPERATURE (°C)
MAX6469 toc17
603510-15