Maxim MAX6322HPUK50C-T, MAX6322HPUK50D-T, MAX6322HPUK46D-T, MAX6322HPUK47A-T, MAX6322HPUK47B-T Datasheet
...
___________________________________________________________________Selector Guide
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
________________General Description
The MAX6316–MAX6322 family of microprocessor (µP)
supervisory circuits monitors power supplies and
microprocessor activity in digital systems. It offers several combinations of push/pull, open-drain, and bidirectional (such as Motorola 68HC11) reset outputs, along
with watchdog and manual-reset features. The
Selector
Guide
below lists the specific functions available from
each device. These devices are specifically designed
to ignore fast negative transients on VCC. Resets are
guaranteed valid for VCCdown to 1V.
These devices are available in 26 factory-trimmed reset
threshold voltages (from 2.5V to 5V, in 100mV increments), featuring four minimum power-on reset timeout
periods (from 1ms to 1.12sec), and four watchdog timeout periods (from 6.3ms to 25.6sec). Nine standard versions are available with an order increment requirement
of 2500 pieces (see
Standard Versions
table); contact
the factory for availability of other versions, which have
an order increment requirement of 10,000 pieces.
The MAX6316–MAX6322 are offered in a miniature
5-pin SOT23 package.
________________________Applications
Portable Computers
Computers
Controllers
Intelligent Instruments
Portable/Battery-Powered Equipment
Embedded Control Systems
____________________________Features
♦ Small 5-Pin SOT23 Package
♦ Available in 26 Reset Threshold Voltages
2.5V to 5V, in 100mV Increments
♦ Four Reset Timeout Periods
1ms, 20ms, 140ms, or 1.12sec (min)
♦ Four Watchdog Timeout Periods
6.3ms, 102ms, 1.6sec, or 25.6sec (typ)
♦ Four Reset Output Stages
Active-High, Push/Pull
Active-Low, Push/Pull
Active-Low, Open-Drain
Active-Low, Bidirectional
♦ Guaranteed Reset Valid to VCC= 1V
♦ Immune to Short Negative VCCTransients
♦ Low Cost
♦ No External Components
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
________________________________________________________________
Maxim Integrated Products
1
19-0496; Rev 3; 1/99
PART
MAX6316LUK____-T
MAX6316MUK____-T -40°C to +85°C
-40°C to +85°C
TEMP. RANGE PIN-PACKAGE
5 SOT23-5
5 SOT23-5
_______________Ordering Information
Ordering Information continued at end of data sheet.
MAX6317HUK____-T
-40°C to +85°C 5 SOT23-5
MAX6318HUK____-T
-40°C to +85°C 5 SOT23-5
ACTIVE-LOW
OPEN-DRAIN
MAX6316L
MAX6316M
MAX6317H
✔
✔
✔
MAX6321HP
✔
✔
✔
✔
MAX6318LH
✔
—
MAX6318MH**
✔
—
MAX6319LH —
✔
MAX6319MH** —
✔
MAX6320P
✔ ✔
ACTIVE-LOW
PUSH/PULL
✔
—
—
✔
—
✔
—
—
ACTIVE-HIGH
PUSH/PULL
—
—
✔
✔
✔
✔
✔
—
ACTIVE-LOW
BIDIRECTIONAL
—
✔
—
—
✔
—
✔
—
PART
WATCHDOG
INPUT
MANUAL
RESET
INPUT
— —
✔
—
—
✔
MAX6322HP —
✔
—
—
—
—
—
—
✔
RESET OUTPUTS*
—
✔
—
✔
*
The MAX6318/MAX6319/MAX6321/MAX6322 feature two types of reset output on each device.
**
Future product—contact factory for availability.
MAX6318MHUK____-T -40°C to +85°C 5 SOT23-5
Typical Operating Circuit and Pin Configurations appear at
end of data sheet.
ELECTRICAL CHARACTERISTICS
(VCC= 2.5V to 5.5V, TA= -40°C to +85°C, unless otherwise noted. Typical values are at TA= +25°C.) (Note 1)
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Voltage (with respect to GND)
V
CC
......................................................................-0.3V to +6V
RESET (MAX6320/MAX6321/MAX6322 only)...... -0.3V to +6V
All Other Pins.........................................-0.3V to (V
CC
+ 0.3V)
Input/Output Current, All Pins .............................................20mA
Continuous Power Dissipation (T
A
= +70°C)
SOT23-5 (derate 7.1mW/°C above +70°C)...............571mW
Operating Temperature Range............................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range..............................-65°C to +160°C
Lead Temperature (soldering, 10sec)..............................+300°C
VCC- 1.5
0.8 x V
CC
V
OH
0.4
0.3
0.3
V
0.3
V
OL
RESET Output Voltage
µs40t
RD
VCCto RESET Delay
1120 1600 2240
140 200 280
20 28 40
ms
1 1.4 2
t
RP
Reset Active Timeout Period
mV3Reset Threshold Hysteresis
V1 5.5V
CC
Operating Voltage Range
VTH-2.5% VTHVTH+2.5%
V
VTH-1.5% VTHVTH+1.5%
V
RST
Reset Threshold (Note 2)
ppm/°C40
∆VTH/°C
Reset Threshold Temperature
Coefficient
UNITSMIN TYP MAXSYMBOLPARAMETER
VCC≥ 4.5V, I
SOURCE
= 800µA
VCC≥ 2.7V, I
SOURCE
= 500µA
VCC≥ 4.5V, I
SINK
= 3.2mA
VCC≥ 2.7V, I
SINK
= 1.2mA
VCC≥ 1.2V, I
SINK
= 100µA
VCC≥ 1.0V, I
SINK
= 50µA
TA= -40°C to +85°C
VCCfalling at 1mV/µs
MAX63_ _D_-T
TA= -40°C to +85°C
TA= +25°C
MAX63_ _C_-T
MAX63_ _B_-T
MAX63_ _A_-T
CONDITIONS
V
0.3
V
OL
RESET Output Voltage
VCC≥ 2.7V, I
SINK
= 1.2mA
0.4VCC≥ 4.5V, I
SINK
= 3.2mA
0.8 x V
CC
V
OH
VCC≥ 1.8V, I
SOURCE
= 150µA
0.8 x V
CC
VCC≥ 2.7V, I
SOURCE
= 500µA
VCC- 1.5VCC≥ 4.5V, I
SOURCE
= 800µA
Note 1: Over-temperature limits are guaranteed by design, not production tested.
Note 2: A factory-trimmed voltage divider programs the nominal reset threshold (V
TH
). Factory-trimmed reset thresholds are
available in 100mV increments from 2.5V to 5V (see Table 1 at end of data sheet).
MAX6316/MAX6317/MAX6318/
MAX6320/MAX6321:
MR and WDI unconnected
µA
10 20
I
CC
Supply Current
VCC= 5.5V
512VCC= 3.6V
MAX6319/MAX6322:
MR unconnected
512VCC= 5.5V
38VCC= 3.6V
PUSH/PULL RESET OUTPUT (MAX6316L/MAX6317H/MAX6318_H/MAX6319_H/MAX6321HP/MAX6322HP)
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
_______________________________________________________________________________________ 3
Note 3: This is the minimum time RESET must be held low by an external pull-down source to set the active pull-up flip-flop.
Note 4: Measured from RESET V
OL
to (0.8 x VCC), R
LOAD
= ∞.
Note 5: WDI is internally serviced within the watchdog period if WDI is left unconnected.
Note 6: The WDI input current is specified as the average input current when the WDI input is driven high or low. The WDI input is
designed for a three-stated-output device with a 10µA maximum leakage current and capable of driving a maximum capacitive load of 200pF. The three-state device must be able to source and sink at least 200µA when active.
µA1.0I
LKG
Open-Drain Reset Output
Leakage Current
ns400t
S
Transition Flip-Flop Setup Time
333
ns
333
t
R
RESET Output Rise Time
(Note 4)
UNITSMIN TYP MAXSYMBOLPARAMETER
(Note 3)
VCC= 5.0V, CL= 200pF
VCC= 3.0V, CL= 120pF
CONDITIONS
ELECTRICAL CHARACTERISTICS (continued)
(VCC= 2.5V to 5.5V, TA= -40°C to +85°C, unless otherwise noted. Typical values are at TA= +25°C.) (Note 1)
666
666
VCC= 5.0V, CL= 400pF
VCC= 3.0V, CL= 250pF
V0.4 0.65V
PTH
Active Pull-Up Enable Threshold VCC= 5.0V
mA20
RESET Active Pull-Up Current
VCC= 5.0V
kΩ
4.2 4.7 5.2
RESET Pull-Up Resistance
V
0.3
V
OL
RESET Output Voltage
VCC≥ 1.0V, I
SINK
= 50µA
0.3VCC≥ 1.2V, I
SINK
= 100µA
0.3VCC≥ 2.7V, I
SINK
= 1.2mA
0.4VCC≥ 4.5V, I
SINK
= 3.2mA
ms
4.3 6.3 9.3
t
WD
Watchdog Timeout Period
MAX63_ _ _ W-T
71 102 153MAX63_ _ _ X-T
sec
1.12 1.6 2.4MAX63_ _ _ Y-T
17.9 25.6 38.4MAX63_ _ _ Z-T
ns50t
WDI
WDI Pulse Width VIL= 0.3 x VCC, VIH= 0.7 x V
CC
V
0.3 x V
CC
V
IL
WDI Input Threshold (Note 5)
0.7 x V
CC
120 160
I
WDI
WDI Input Current
(Note 6)
WDI = VCC, time average
-20 -15V
WDI
= 0, time average
V
IH
V
0.8V
IL
MR Input Threshold
VTH> 4.0V
2.0V
IH
0.3 x V
CC
V
IL
VTH< 4.0V
0.7 x V
CC
V
IH
µs1
MR Input Pulse Width
ns100
MR Glitch Rejection
kΩ
35 52 75
MR Pull-Up Resistance
ns230
MR to Reset Delay
VCC= 5V
µA
BIDIRECTIONAL RESET OUTPUT (MAX6316M/MAX6318MH/MAX6319MH)
OPEN-DRAIN RESET OUTPUT (MAX6320P/MAX6321HP/MAX6322HP)
WATCHDOG INPUT (MAX6316/MAX6317H/MAX6318_H/MAX6320P/MAX6321HP)
MANUAL-RESET INPUT (MAX6316_/MAX6317H/MAX6319_H/MAX6320P/MAX6322HP)
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
4 _______________________________________________________________________________________
__________________________________________Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
0
2
1
4
3
8
7
6
5
10
9
-40 0 20-20 40 60 80 100
MAX6316/17/18/20/21
SUPPLY CURRENT vs. TEMPERATURE
MAX6316toc01
TEMPERATURE (°C)
SUPPLY CURRENT (µA)
VCC = 5V
VCC = 3V
VCC = 1V
0
30
20
10
50
40
90
80
70
60
100
-40 -20 0 20 40 60 80 100
VCC FALLING TO RESET PROPAGATION
DELAY vs. TEMPERATURE
MAX6316toc03
TEMPERATURE (°C)
RESET PROPAGATION DELAY (µs)
VCC FALLING AT 1mV/µs
V
RST
- VCC = 100mV
140
180
160
240
220
200
300
280
260
320
-40 0 20-20 40 60 80 100
MAX6316/17/19/20/22
MANUAL-RESET TO RESET
PROPAGATION DELAY vs. TEMPERATURE
MAX6316toc04
TEMPERATURE (°C)
PROPAGATION DELAY (ns)
VCC = 5V
0.95
0.98
0.97
0.96
1.00
0.99
1.04
1.03
1.02
1.01
1.05
-40 -20 0 20 40 60 80 100
NORMALIZED RESET TIMEOUT
PERIOD vs. TEMPERATURE
MAX6316toc05
TEMPERATURE (°C)
NORMALIZED RESET TIMEOUT PERIOD
0.95
0.98
0.97
0.96
1.00
0.99
1.04
1.03
1.02
1.01
1.05
-40 -20 0 20 40 60 80 100
MAX6316/17/18/20/21
NORMALIZED WATCHDOG TIMEOUT
PERIOD vs. TEMPERATURE
MAX6316toc06
TEMPERATURE (°C)
NORMALIZED WATCHDOG TIMEOUT PERIOD
80
0
10 100 1000
MAXIMUM VCC TRANSIENT DURATION
vs. RESET THRESHOLD OVERDRIVE
20
10
MAX6316toc08
RESET THRESHOLD OVERDRIVE (mV) V
RST
- V
CC
TRANSIENT DURATION (µs)
30
50
60
40
70
V
RST
= 3.3V
V
RST
= 4.63V
V
RST
= 2.63V
RESET OCCURS ABOVE LINES
PASSIVE
4.7kΩ
PULL-UP
2V/div
RESET, ACTIVE
PULL-UP
2V/div
RESET
INPUT
5V/div
200ns/div
MAX6316M/6318MH/6319MH
BIDIRECTIONAL
PULL-UP CHARACTERISTICS
MAX6316toc09
100pF
4.7k
+5V
74HC05
74HC05
V
CC
GND
MR
100pF
INPUT
INPUT
+5V
RESET
MAX6316–MAX6322
5-Pin µP Supervisory Circuits with
Watchdog and Manual Reset
_______________________________________________________________________________________ 5
______________________________________________________________Pin Description
11—
MAX6316M/MAX6318MH/MAX6319MH:
Bidirectional, Active-Low, Reset Output.
Intended to interface directly to microprocessors
with bidirectional resets such as the Motorola
68HC11.
MAX6320P/MAX6321HP/MAX6322HP:
Open-Drain, Active-Low, Reset Output. NMOS output (sinks current only). Connect a pull-up resistor
from RESET to any supply voltage up to 6V.
MAX6316L/MAX6318LH/MAX6319LH:
Active-Low, Reset Output. CMOS push/pull
output (sources and sinks current).
RESET
1
4
—
5
3
2
MAX6319LH
MAX6319MH
MAX6322HP
PIN
—
4
5
3
2
MAX6318LH
MAX6318MH
MAX6321HP
3
4
5
1
2
MAX6317H
Active-Low, Manual Reset Input. Pull low to force a
reset. Reset remains asserted for the duration of
the Reset Timeout Period after MR transitions from
low to high. Leave unconnected or connected to
V
CC
if not used.
MR
3
Watchdog Input. Triggers a reset if it remains
either high or low for the duration of the watchdog
timeout period. The internal watchdog timer clears
whenever a reset asserts or whenever WDI sees a
rising or falling edge. To disable the watchdog feature, leave WDI unconnected or three-state the driver connected to WDI.
WDI4
Supply Voltage. Reset is asserted when V
CC
drops below the Reset Threshold Voltage (V
RST
).
Reset remains asserted until VCCrises above
V
RST
and for the duration of the Reset Timeout
Period (tRP) once VCCrises above V
RST
.
V
CC
5
Active-High, Reset Output. CMOS push/pull output
(sources and sinks current). Inverse of RESET.
RESET—
GroundGND2
MAX6316L
MAX6316M
MAX6320P
FUNCTIONNAME
Loading...