Maxim MAX4512CSE, MAX4512CPE, MAX4512C-D, MAX4511MJE, MAX4511ESE Datasheet

...

General Description

The MAX4511/MAX4512/MAX4513 are quad, singlepole/single-throw (SPST), fault-protected analog switches. They are pin-compatible with the industry-standard nonprotected DG201/DG202/DG213. These new switches feature fault-protected inputs and Rail-to-Rail®signal handling capability. The normally open (NO_) and normally closed (NC_) terminals are protected from overvoltage faults up to 36V during power-up or power-down. During a fault condition, the NO_ or NC_ terminal becomes an open circuit and only nanoamperes of leakage current flow from the source, but the switch output (COM_) furnishes up to 10mA of the appropriate polarity supply voltage to the load. This ensures unambiguous rail-to-rail outputs when a fault begins and ends.

On-resistance is 175Ω max and is matched between switches to 10Ω max. The off-leakage current is only

0.5nA at +25°C and 10nA at +85°C. The MAX4511 has four normally closed switches. The

MAX4512 has four normally open switches. The MAX4513 has two normally closed and two normally open switches.

These CMOS switches can operate with dual power supplies ranging from ±4.5V to ±18V or a single supply between +9V and +36V.

All digital inputs have +0.8V and +2.4V logic thresholds, ensuring both TTL- and CMOS-logic compatibility when using ±15V or a single +12V supply.

Applications

ATE Equipment Data Acquisition Industrial and Process-Control Systems Avionics Redundant/Backup Systems

Features

♦ ±40V Fault Protection with Power Off

±36V Fault Protection with ±15V Supplies

♦ All Switches Off with Power Off ♦ Rail-to-Rail Signal Handling ♦ Output Clamped to Appropriate Supply Voltage

During Fault Condition; No Transition Glitch

♦ 175Ω max Signal Paths with ±15V Supplies ♦ No Power-Supply Sequencing Required ♦ ±4.5V to ±18V Dual Supplies

+9V to +36V Single Supply

♦ Low Power Consumption, <2mW ♦ Four Separately Controlled SPST Switches ♦ Pin-Compatible with Industry-Standard

DG411/DG412/DG413, DG201/DG202/DG213

♦ TTL- and CMOS-Compatible Logic Inputs with

Single +9V to +15V or ±15V Supplies

For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 408-737-7600 ext. 3468.

MAX4511/MAX4512/MAX4513

Quad, Rail-to-Rail, Fault-Protected,

SPST Analog Switches

________________________________________________________________

Maxim Integrated Products

TOP VIEW

DIP/SO

MAX4511

LOGIC SWITCH

0 1

OFF

16 15 14 13 12 11 10

1 2 3 4 5 6 7 8

IN2 COM2 NC2

V+

V-

NC1

COM1

IN1

MAX4511

N.C. NC3 COM3 IN3

IN4

COM4

NC4

GND

N.C. = NOT CONNECTED SWITCHES SHOWN FOR LOGIC "0" INPUT. ALL SWITCHES ARE OFF WITH POWER REMOVED.

19-4760; Rev 0; 6/98

Ordering Information continued at end of data sheet.

Contact factory for dice specifications.

Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.

Ordering Information

PART TEMP. RANGE PIN-PACKAGE

MAX4511C/D 0°C to +70°C Dice*

MAX4511CPE

0°C to +70°C 16 Plastic DIP

MAX4511CSE 0°C to +70°C 16 Narrow SO

Continued at end of data sheet.

MAX4511EPE -40°C to +85°C 16 Plastic DIP

MAX4511MJE -55°C to +125°C 16 CERDIP

MAX4511ESE -40°C to +85°C 16 Narrow SO

Pin Configurations/

Functional Diagrams/Truth Tables

MAX4511/MAX4512/MAX4513

Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches

2 _______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL CHARACTERISTICS—Dual Supplies

(

V+ = +15V, V- = -15V, GND = 0V, TA =T

MIN

to T

MAX

, unless otherwise noted. Typical values are at TA= +25°C.)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

Note 1: COM_ and IN_ pins are not fault protected. Signals on COM_ or IN_ exceeding V+ or V- are clamped by internal diodes.

Limit forward diode current to maximum current rating.

Note 2: NC_ and NO_ pins are fault protected. Signals on NC_ or NO_ exceeding -36V to +36V may damage the device. These

limits apply with power applied to V+ or V-, or ±40V with V+ = V- = 0.

(Voltages Referenced to GND)

V+........................................................................-0.3V to +44.0V

V-.........................................................................-44.0V to +0.3V

V+ to V-................................................................-0.3V to +44.0V

COM_, IN_ (Note 1)..............................(V- - 0.3V) to (V+ + 0.3V)

NC_, NO_ (Note 2)..................................(V+ - 36V) to (V- + 36V)

NC_, NO_ to COM_.................................................-36V to +36V

Continuous Current into Any Terminal..............................±30mA

Peak Current into Any Terminal

(pulsed at 1ms, 10% duty cycle)...................................±50mA

Continuous Power Dissipation (T

= +70°C) (Note 2)

Plastic DIP (derate 10.53mW/°C above +70°C) ...........842mW

Narrow SO (derate 8.70mW/°C above +70°C) .............696mW

CERDIP (derate 10.00mW/°C above +70°C)................800mW

Operating Temperature Ranges

MAX451_C_ E......................................................0°C to +70°C

MAX451_E_ E ...................................................-40°C to +85°C

MAX451_MJE .................................................-55°C to +125°C

Storage Temperature Range.............................-65°C to +150°C

Lead Temperature (soldering, 10sec).............................+300°C

Applies with power on or off (Note 2)

COM_

= ±14V;

NO_,VCOM

= 14V

COM_

= ±10V, I

COM_

= 1mA

COM_

= ±10V, I

COM_

= 1mA

CONDITIONS

C, E, M

-20 20

nAI

COM_(OFF)

-0.5 0.01 0.5

V-36 36V

NO_

, V

NC_

Fault-Protected Analog Signal Range

∆R

COM_ -NO_ or COM_ -NC_ On-Resistance Match Between Channels (Note 4)

Ω

250

COM_ -NO_ or COM_ -NC_ On-Resistance

125 160

UNITS

MIN TYP MAX

(Note 3)

SYMBOLPARAMETER

C, E

+25°C

Applies with power on or off (Note 2)

C, E, M VV- V+V

NO_

, V

NC_

Fault-Free Analog Signal Range

Ω

15M

Applies with power on or off (Note 1)

C, E, M VV- - 0.3 V+ + 0.3V

COM_

Non-Protected Analog Signal Range (COM_ Output)

ANALOG SWITCH

200C, E

C, E 10

COM_ Off Leakage Current (Note 5)

COM_

= ±14V;

NO_,VCOM

= 14V

NO_ or NC_ Off Leakage Current (Note 5)

NO_(OFF),

NC_(OFF)

-0.5 0.01 0.5+25°C

-10 10C, E

-200 200M

-10 10C, E

-200 200M

COM_

= ±14V nAI

COM_(ON)

COM_ On Leakage Current (Note 5)

-0.5 0.01 0.5+25°C

-400 400M

MAX4511/MAX4512/MAX4513

Quad, Rail-to-Rail, Fault-Protected,

SPST Analog Switches

_______________________________________________________________________________________ 3

ELECTRICAL CHARACTERISTICS—Dual Supplies (continued)

(

V+ = +15V, V- = -15V, GND = 0V, TA =T

MIN

to T

MAX

, unless otherwise noted. Typical values are at TA= +25°C.)

NO_

or VNC_ = ±33V

NO_

or VNC_ = ±33V

CONDITIONS

+25°C

Turn-On Time 600

kΩR

COM_

COM_ On Output Resistance, Supplies On

1 2.5

-10 10

COM_

COM_ Output Leakage Current, Supplies On

UNITS

MIN TYP MAX

(Note 3)

SYMBOLPARAMETER

+25°C

NO_

or VNC_ = 33V

mAI

COM_

COM_ On Output Current, Supplies On

81113

+25°C

NO_

or VNC_ = ±40V,

V+ = 0, V- = 0

µA-10 10

NO_

, I

NC_

NO_ or NC_ Input Leakage Current, Supplies Off

-200 200

+25°C

M -1 1 µA

1.9 2.4 VV

IN_H

IN_ Input Logic Threshold High C, E, M

900M

COM_

= ±10V, RL_= 2kΩ,

Figure 3

nst

BBM

Break-Before-Make Time Delay (MAX4513 Only)

50 100+25°C

-1 0.03 1

VIN_ = 0.8V or 2.4V µAI

INH

_, I

INL

IN_ Input Current Logic High or Low

+25°C

C, E -200 200

C, E

NO_

or VNC_ = -33V -12 -10 -7

C, E, M

C, E, M -5 5

C, E

350 500

COM_

= ±10V, RL_= 2kΩ,

Figure 2

OFF

Turn-Off Time 500C, E

750M

200 400

COM_

= ±10V, RL_= 2kΩ,

Figure 2

+25°C

NO_

or VNC_ = ±25V,

COM_

= 10V

µA-10 10

NO_

, I

NC_

NO_ or NC_ Off Input Leakage Current, Supplies On

-200 200

+25°C

C, E

-20 20

-20 0.1 20

SWITCH DYNAMIC CHARAC-

CL= 1.0nF, V

NO_

= 0,

RS = 0Ω, Figure 4

pCQCharge Injection (Note 6) 1.5 5+25°C

f = 1MHz, Figure 5 pFC

N_(OFF)

NO_ or NC_ Off-Capacitance 10+25°C

f = 1MHz, Figure 5 pFC

COM_(OFF)

COM_ Off-Capacitance 5+25°C

f = 1MHz, Figure 5 pFC

COM_(ON)

COM_ On-Capacitance 10+25°C

LOGIC INPUT

RL= 50Ω, CL= 15pF, VN_= 1V

RMS

, f = 1MHz, Figure 6

dBVC

ISO

Off Isolation (Note 7) -62+25°C

RL= 50Ω, CL= 15pF, VN_= 1V

RMS

, f = 1MHz, Figure 6

dBV

Channel-to-Channel Crosstalk (Note 9)

-66+25°C

0.8 1.9 VV

IN_L

IN_ Input Logic Threshold Low C, E, M

FAULT (V+ = +15V, V- = -15V, unless otherwise noted.)

LOGIC INPUT

SWITCH DYNAMIC CHARACTERISTICS

All V

IN_

= 0 or 15V

MAX4511/MAX4512/MAX4513

Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches

4 _______________________________________________________________________________________

ELECTRICAL CHARACTERISTICS—Dual Supplies (continued)

(

V+ = +15V, V- = -15V, GND = 0V, T

A = TMIN

to T

MAX

, unless otherwise noted. Typical values are at TA= +25°C.)

CONDITIONS UNITS

MIN TYP MAX

(Note 3)

SYMBOLPARAMETER T

Power-Supply Range V+, V- C,E, M ±4.5 ±18 V V+ Supply Current I+ All V

IN_

= 0 or 5V

+25°C 280 400

µA

V- Supply Current I- All V

IN_

= 0 or 5V

+25°C 90 200

µA

GND Supply Current I

GND

All V

IN_

= 0 or 15V

+25°C -1 0.01 1

µA

600C, E, M

C, E, M 300

C, E, M 10

+25°C 150 250

µA

C, E, M 450

All V

IN_

= 5V

POWER SUPPLY

MAX4511/MAX4512/MAX4513

Quad, Rail-to-Rail, Fault-Protected,

SPST Analog Switches

_______________________________________________________________________________________ 5

ELECTRICAL CHARACTERISTICS—Single +12V Supply

(V+ = +10.8V to +13.2V, V- = 0, TA= T

MIN

to T

MAX

, unless otherwise noted. Typical values are at TA= +25°C.)

Applies with power on or off (Note 2)

C, E, M V

Applies with power on or off (Note 2)

0V+V

NO_

, V

NC_

Fault-Free Analog Signal Range

V+ = 12V; V

COM _

= 0;

NO_

, V

NC_

= 12V

V+ = 12V, V

COM_

= 10V,

COM_

= 1mA

V+ = 12V, V

COM_

= 10V,

COM_

= 1mA

CONDITIONS

C, E, M

Applies with power on or off (Note 1)

C, E, M V-0.3 V+ + 0.3V

COM_

Non-Protected Analog Signal Range (COM_ Output)

V+ = 12V; V

COM_

= 10V;

NO_

, V

= 0 or 12V

Ω

ON_(OFF),

NC_(OFF)

30M

NO_ or NC_ Off Leakage Current (Notes 5, 9)

-0.5 0.01 0.5+25°C

nAI

COM_(OFF)

COM_ Off Leakage Current (Notes 5, 9)

-0.5 0.01 0.5

V-36 36V

NO_

, V

NC_

Fault-Protected Analog Signal Range

∆R

COM_ -NO_ or COM_ -NC_ On-Resistance Match Between Channels (Note 4)

Ω

525

COM_ -NO_ or COM_ -NC_ On-Resistance

UNITS

MIN TYP MAX

(Note 3)

SYMBOLPARAMETER

+25°C

C, E

+25°C

+25°C 410

260 390

450

-10 10C, E

M -200 200

-10 10C, E

-200 200M

V+ = 12V, V

COM_

= 10V or 12V

-20 20C, E nAI

COM_(ON)

COM_ On Leakage Current (Notes 5, 9)

-400 400M

-0.5 0.01 0.5+25°C

NO_

or VNC_ = ±25V,

COM_

= 0, V+ = 12V

-200 200C, E

NO_

, I

NC_

NO_ or NC_ Off Input Leakage Current, Supply On

-10 10M

-20 20+25°C

NO_

or VNC_ = ±40V,

V+ = 0, V- = 0

-200 200C, E

NO_

, I

NC_

NO_ or NC_ Input Leakage Current, Supply Off

-10 10M

-20 0.1 20+25°C

NO_

or VNC_ = 25V,

V+ = 12V

235mAI

COM_

COM_ Output Current, Supply On

+25°C

NO_

or VNC_ = 10V

V+ = 12V

kΩR

COM_

COM_ Output Resistance, Supply On

2.4 5+25°C

µA

NO_

or VNC_ = ±30V,

V+ = 12V

-200 200C, E

COM_

COM_ Output Leakage Current, Supply On

-1 1M

-10 10+25°C

µA

FAULT

ANALOG SWITCH

+ 11 hidden pages