General Description
The MAX4030E/MAX4031E unity-gain stable op amps
combine high-speed performance, rail-to-rail outputs,
and ±15kV ESD protection. Targeted for applications
where an input or an output is exposed to the outside
world, such as video and communications, these
devices are compliant with International ESD
Standards: ±15kV IEC 1000-4-2 Air-Gap Discharge,
±8kV IEC 1000-4-2 Contact Discharge, and the ±15kV
Human Body Model.
The MAX4030E/MAX4031E operate from a single 5V
supply and consume only 12mA of quiescent supply
current per amplifier while achieving a 144MHz -3dB
bandwidth, 20MHz 0.1dB gain flatness, and a 115V/µs
slew rate. The MAX4031E provides individual shutdown
control for each of the amplifiers.
The dual MAX4030E is available in 8-pin µMAX®and SO
packages, and the triple MAX4031E is available in 14-pin
TSSOP and SO packages. All devices are specified over
the -40°C to +85°C extended temperature range.
Applications
Features
♦ ESD-Protected Video Inputs and Outputs
±15kV – Human Body Model
±8kV – IEC 1000-4-2 Contact Discharge
±15kV – IEC 1000-4-2 Air-Gap Discharge
♦ 5V Single-Supply Operation
♦ 0.1µA Low-Power Shutdown Mode (MAX4031E)
♦ Input Common-Mode Range Extends to Ground
♦ 2V
P-P
Large-Signal -3dB BW > 50MHz
♦ Directly Drives 150Ω Loads
♦ Low Differential Gain/Phase: 0.2%/0.2°
♦ -40°C to +85°C Extended Temperature Range
♦ Compact 8-Pin µMAX and 14-Pin TSSOP
Packages
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
________________________________________________________________ Maxim Integrated Products 1
19-3570; Rev 1; 6/05
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Ordering Information
PART
PIN-PACKAGE
MAX4030EEUA
8 µMAX
MAX4030EESA
8 SO
MAX4031EEUD
14 TSSOP
MAX4031EESD
14 SO
INB-
INB+GND
1
2
87V
CC
OUTBINA-
INA+
OUTA
µMAX/SO
3
4
6
5
MAX4030E
14
13
12
11
10
9
8
1
2
3
4
5
6
7
OUTC
INC-
INC+
GNDV
CC
TOP VIEW
MAX4031E
INB+
INB-
OUTBOUTA
INA-
INA+
TSSOP/SO
SHDNA
SHDNC
SHDNB
Pin Configurations
200Ω
75Ω
200Ω
75Ω
75Ω
OUT
VIDEO LINE DRIVER
Z
o
= 75Ω
MAX4030E
MAX4031E
5V
0.1µF
IN_+
Typical Operating Circuit
Set-Top Boxes
Standard Definition
Television (SDTV)
Enhanced Television
(ETV)
High-Definition
Television (HDTV)
Notebooks
Projectors
Security Video Systems
Camcorders
Digital Still Cameras
Portable DVD Players
µMAX is a registered trademark of Maxim Integrated Products, Inc.
TEMP RANGE
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
(All voltages referenced to GND, unless otherwise noted.)
V
CC
...........................................................................-0.3V to +6V
IN_-, IN_+, OUT_,
SHDN_ ..........................-0.3V to (VCC+ 0.3V)
Current into IN_-, IN_+, SHDN..........................................±20mA
Output Short-Circuit Duration to V
CC
or GND............Continuous
Continuous Power Dissipation (T
A
= +70°C)
8-Pin µMAX (derate 4.5mW/°C above +70°C) .............362mW
8-Pin SO (derate 5.9mW/°C above +70°C)..................471mW
14-Pin TSSOP (derate 9.1mW/°C above +70°C) .........727mW
14-Pin SO (derate 8.3mW/°C above +70°C)................667mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature .....................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
DC ELECTRICAL CHARACTERISTICS
(VCC= 5V, VCM= 0V, V
OUT_
= VCC/2, SHDN_ = VCC, RL= ∞ to VCC/2, TA = T
MIN
to T
MAX
, unless otherwise noted. Typical values are
at T
A
= +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Operating Supply Voltage Range
V
CC
Guaranteed by PSRR
V
Quiescent Current (per Amplifier)
I
CC
12 22 mA
Shutdown Current (per Amplifier) I
SHDN
SHDN_ = GND (MAX4031E)
10 µA
Input Common-Mode Voltage V
CM
Guaranteed by CMRR 0
V
CC
V
TA = +25°C 5 13
Input Offset Voltage V
OS
TA = -40°C to +85°C 26
mV
Input Offset Voltage Matching ∆V
OS
mV
Input Offset Voltage Tempco
31
Input Bias Current I
B
1µA
Input Offset Current I
OS
µA
Input Resistance R
IN
1GΩ
Common-Mode Rejection Ratio
GND ≤ VCM ≤ VCC - 2.25V 50 70 dB
Power-Supply Rejection Ratio PSRR 4.5V ≤ VCC ≤ 5.5V 40 60 dB
0.5V ≤ V
OUT_
≤ 4.5V, RL = 2kΩ to VCC/2 80
0.6V ≤ V
OUT_
≤ 4.4V, RL = 150Ω to VCC/2 50 70Open-Loop Gain A
VOL
0.4V ≤ V
OUT_
≤ 3.5V, RL = 150Ω to GND 50 70
dB
VCC - V
OH
RL = 2kΩ to VCC/2
V
OL
- GND
VCC - V
OH
VOL - GND
VCC - V
OH
Output Voltage Swing V
OUT_
RL = 150Ω to GND
V
OL
- GND
V
Output Short-Circuit Current I
SC
Sinking or sourcing
mA
V
IL
MAX4031E
SHDN_ Logic Threshold
V
IH
MAX4031E
V
I
IL
SHDN_ = GND (MAX4031E)
10
SHDN_ Logic Input Current
I
IH
SHDN_ = V
CC
(MAX4031E)
10
µA
4.5 5.5
TC
VOS
CMRR
RL = 150Ω to VCC/2
2.0
0.1
2.6
0.01
0.01
0.05
0.05
0.15 0.4
0.15 0.4
0.3 0.8
0.01 0.05
±100
0.10
0.10
2.25
µV/°C
0.8
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
_______________________________________________________________________________________ 3
AC ELECTRICAL CHARACTERISTICS
(VCC= 5V, VCM= 1.5V, RL= 150Ω to GND, SHDN_ = VCC, A
VCL_
= +2V/V, TA= +25°C, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
V
OUT_
= 100mV
P-P
, A
VCL
= +1V/V
Small-Signal -3dB Bandwidth BW
SS
V
OUT_
= 100mV
P-P
, A
VCL
= +2V/V 53
MHz
V
OUT_
= 2V
P-P
, A
VCL
= +1V/V 52
Large-Signal -3dB Bandwidth BW
LS
V
OUT_
= 2V
P-P
, A
VCL
= +2V/V 40
MHz
V
OUT_
= 100mV
P-P
, A
VCL
= +1V/V 20
Small-Signal 0.1dB Gain Flatness
V
OUT_
= 100mV
P-P
, A
VCL
= +2V/V 10
MHz
V
OUT_
= 2V
P-P
, A
VCL
= +1V/V 20
Large-Signal 0.1dB Gain Flatness
V
OUT_
= 2V
P-P
, A
VCL
= +2V/V 9
MHz
Slew Rate SR V
OUT_
= 2V step
V/µs
Settling Time to 0.1% t
S
V
OUT_
= 2V step 40 ns
Channel-to-Channel Isolation CH
ISO
f = 4.43MHz 65 dB
Differential Phase Error DP NTSC, RL = 150Ω to GND, A
VCL
= +2V/V
Degrees
Differential Gain Error DG NTSC, RL = 150Ω to GND, A
VCL
= +2V/V
%
Input Capacitance C
IN
8pF
Capacitive-Load Stability No sustained oscillations
pF
Output Impedance Z
OUT
f = 4.43MHz 2 Ω
Enable Time t
ON
V
IN_
= 1V (MAX4031E) 2 µs
Disable Time t
OFF
V
IN_
= 1V (MAX4031E)
µs
DC ELECTRICAL CHARACTERISTICS (continued)
(VCC= 5V, VCM= 0V, V
OUT_
= VCC/2, SHDN_ = VCC, RL= ∞ to VCC/2, TA = T
MIN
to T
MAX
, unless otherwise noted. Typical values are
at T
A
= +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Disabled Output Leakage Current
SHDN_ = GND (MAX4031E)
10 µA
Human Body Model
IEC 1000-4-2 Contact Discharge ±8ESD Protection Voltage (Note 2)
IEC 1000-4-2 Air-Gap Discharge
kV
Note 1: All devices are 100% production tested at TA= +25°C. Specifications over temperature limits are guaranteed by design.
Note 2: ESD protection is specified for test point A and test point B only (Figure 7).
I
OUT_SH
BW
0.1dBSS
BW
0.1dBLS
0.1
±15
±15
144
115
0.2
0.2
200
0.15
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
4 _______________________________________________________________________________________
Typical Operating Characteristics
(VCC= 5V, VCM= 1.5V, A
VCL
= +2V/V, RL= 150Ω to VCC/2, TA= +25°C, unless otherwise noted.)
SMALL-SIGNAL GAIN vs. FREQUENCY
MAX4030 toc01
FREQUENCY (MHz)
GAIN (dB)
101
-4
-3
-2
-1
0
1
2
3
4
5
-5
0.1 100
V
OUT
= 100mV
P-P
LARGE-SIGNAL GAIN vs. FREQUENCY
MAX4030 toc02
FREQUENCY (MHz)
GAIN (dB)
100101
-5
-4
-3
-2
-1
0
1
2
3
4
-6
0.1 1000
V
OUT
= 2V
P-P
SMALL-SIGNAL GAIN FLATNESS
vs. FREQUENCY
MAX4030 toc03
FREQUENCY (MHz)
NORMALIZED GAIN (dB)
101
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
0.5
-0.5
0.1 100
V
OUT
= 100mV
P-P
LARGE-SIGNAL GAIN FLATNESS
vs. FREQUENCY
MAX4030 toc04
FREQUENCY (MHz)
GAIN (dB)
100101
-0.4
-0.3
-0.2
-0.1
0
0.1
0.2
0.3
0.4
0.5
-0.5
0.1 1000
V
OUT
= 2V
P-P
OUTPUT IMPEDANCE vs. FREQUENCY
MAX4030 toc05
FREQUENCY (MHz)
OUTPUT IMPEDANCE (Ω)
101
0.1
1
10
100
1000
0.01
0.1 100
DISTORTION vs. FREQUENCY
MAX4030 toc06
FREQUENCY (MHz)
DISTORTION (dBc)
101
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
-100
0.1 100
V
OUT
= 2V
P-P
A
VCL
= 2V/V
2ND HARMONIC
3RD HARMONIC
DIFFERENTIAL GAIN
MAX4030 toc07
DIFFERENTIAL GAIN (%)
6th5th4th3rd2nd
-0.1
0.1
-0.2
0
0.2
1st
DIFFERENTIAL PHASE
DIFFERENTIAL PHASE (°)
6th5th4th3rd2nd
-0.1
0.1
-0.2
0
0.2
1st
COMMON-MODE REJECTION
vs. FREQUENCY
MAX4030 toc08
FREQUENCY (MHz)
CMR (dB)
1010.1
-80
-60
-40
-20
0
-100
0.01 100
POWER-SUPPLY REJECTION
vs. FREQUENCY
MAX4030 toc09
FREQUENCY (MHz)
PSR (dB)
101
-80
-60
-40
-20
0
-100
0.1 100
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
_______________________________________________________________________________________ 5
OUTPUT VOLTAGE SWING
vs. RESISTIVE LOAD
MAX4030 toc10
RESISTIVE LOAD (Ω)
VOLTAGE (V)
350300200 250100 15050
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
0
0 400
V
OL
VCC - V
OH
SMALL-SIGNAL PULSE RESPONSE
MAX4030 toc11
V
OUT
50mV/div
V
IN
20mV/div
20ns/div
LARGE-SIGNAL PULSE RESPONSE
MAX4030 toc12
V
OUT
1V/div
V
IN
500mV/div
20ns/div
ISOLATION RESISTANCE
vs. CAPACITIVE LOAD
MAX4030 toc13
CAPACITIVE LOAD (pF)
R
ISO
(Ω)
400300200100
2
4
6
8
10
12
14
16
18
20
0
0 500
CROSSTALK vs. FREQUENCY
MAX4030 toc14
FREQUENCY (MHz)
CROSSTALK (dB)
101
-80
-60
-40
-20
0
-100
0.1 100
Typical Operating Characteristics (continued)
(VCC= 5V, VCM= 1.5V, A
VCL
= +2V/V, RL= 150Ω to VCC/2, TA= +25°C, unless otherwise noted.)
MAX4030E/MAX4031E
Detailed Description
The MAX4030E/MAX4031E dual/triple, 5V operational
amplifiers achieve 115V/µs slew rates and 144MHz
bandwidths. High ±15kV ESD protection at video inputs
and outputs guards against unexpected discharge.
Excellent harmonic distortion and differential gain/
phase performance make these amplifiers an ideal
choice for a wide variety of video and RF signal-processing applications.
Ground-Sensing Inputs
The MAX4030E/MAX4031E input stage can sense common-mode voltages from ground to within 2.25V of the
positive supply.
Rail-to-Rail Outputs
The MAX4030E/MAX4031E rail-to-rail outputs can
swing to within 100mV of each supply because local
feedback around the output stage ensures low openloop output impedance, reducing gain sensitivity to
load variations.
Shutdown (MAX4031E Only)
The MAX4031E offers individual shutdown control for
each amplifier. Drive SHDN_ low to shut down the
amplifier. In shutdown, the amplifier output impedance
is high impedance.
Applications Information
Choosing Resistor Values
Unity-Gain Configuration
The MAX4030E/MAX4031E are internally compensated
for unity gain. When configured for unity gain, a 24Ω
resistor (R
F
) in series with the feedback path optimizes
AC performance. This resistor improves AC response by
reducing the Q of the parallel LC circuit formed by the
parasitic feedback capacitance and lead inductance.
Video Line Driver
The MAX4030E/MAX4031E are low-power, voltagefeedback amplifiers featuring bandwidths up to 40MHz
and 0.1dB gain flatness to 9MHz. They are designed to
minimize differential-gain error and differential-phase
error to 0.2% and 0.2°, respectively. They have a 40ns
settling time to 0.1%, 110V/µs slew rates, and outputcurrent-drive capability of up to 50mA, making them
ideal for driving video loads.
Inverting and Noninverting Configurations
Select the feedback (RF) and input (RG) resistor values
to fit the gain requirements of the application. Large
resistor values increase voltage noise and interact with
the amplifier’s input and PC board capacitance. This
can generate undesirable poles and zeros and
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
6 _______________________________________________________________________________________
PIN
NAME FUNCTION
17OUTA Amplifier A Output
26INA- Amplifier A Inverting Input
35INA+ Amplifier A Noninverting Input
411GND Ground
510INB+ Amplifier B Noninverting Input
69INB- Amplifier B Inverting Input
78OUTB Amplifier B Output
84VCCPositive Power Supply. Bypass VCC to GND with a 0.1µF capacitor.
—1SHDNA Amplifier A Shutdown Input. Connect SHDNA high to enable amplifier A.
—2SHDNC Amplifier C Shutdown Input. Connect SHDNC high to enable amplifier C.
—3SHDNB Amplifier B Shutdown Input. Connect SHDNB high to enable amplifier B.
—12INC+ Amplifier C Noninverting Input
—13INC- Amplifier C Inverting Input
—14OUTC Amplifier C Output
Pin Description
MAX4030E MAX4031E
decrease bandwidth or cause oscillations. For example, a noninverting gain-of-two configuration (RF= RG)
using 2kΩ resistors, combined with 4pF of amplifier
input capacitance and 1pF of PC board capacitance,
cause a pole at 79.6MHz. Since this pole is within the
amplifier bandwidth, it jeopardizes stability. Reducing
the 2kΩ resistors to 100Ω extends the pole frequency
to 1.59GHz, but could limit output swing by adding
200Ω in parallel with the amplifier’s load resistor
(Figures 1 and 2).
Layout and Power-Supply Bypassing
These amplifiers operate from a single 5V power supply. Bypass VCCto ground with a 0.1µF capacitor as
close to VCCas possible. Maxim recommends using
microstrip and stripline techniques to obtain full bandwidth. To ensure that the PC board does not degrade
the amplifier’s performance, design it for a frequency
greater than 1GHz. Pay careful attention to inputs and
outputs to avoid large parasitic capacitance. Under all
conditions observe the following design guidelines:
• Do not use wire-wrap boards. Wire-wrap boards are
too inductive.
• Do not use IC sockets. Sockets increase parasitic
capacitance and inductance.
• Use surface mount instead of through-hole components for better high-frequency performance.
• Use a PC board with at least two layers. The PC
board should be as free from voids as possible.
• Keep signal lines as short and as straight as possible. Do not make 90° turns; round all corners.
Output Capacitive Loading and Stability
The MAX4030E/MAX4031E are optimized for AC performance and do not drive highly reactive loads, which
decreases phase margin and can produce excessive
ringing and oscillation. Figure 3 shows a circuit modification that uses an isolation resistor (R
ISO
) to eliminate
this problem. Figure 4 shows a graph of the Optimal
Isolation Resistor (R
ISO
) vs. Capacitive Load. Figure 5
shows how a capacitive load causes excessive peaking of the amplifier’s frequency response if the capacitor is not isolated from the amplifier by a resistor. A
small isolation resistor (usually 10Ω to 15Ω) placed
before the reactive load prevents ringing and oscillation. At higher capacitive loads, the interaction of the
load capacitance and the isolation resistor controls the
AC performance. Figure 6 shows the effect of a 10Ω
isolation resistor on closed-loop response.
ESD Protection
As with all Maxim devices, ESD protection structures
are incorporated on all pins to protect against ESD
encountered during handling and assembly. Input and
output pins of the MAX4030E/MAX4031E have extra
protection against static electricity. Maxim’s engineers
have developed state-of-the-art structures enabling
these pins to withstand ESD up to ±15kV without damage when placed in the test circuit (Figure 7). The
MAX4030E/MAX4031E are characterized for protection
to the following limits:
•±15kV using the Human Body Model
•±8kV using the Contact Discharge method speci-
fied in IEC 1000-4-2
•±15kV using the Air-Gap Discharge method speci-
fied in IEC 1000-4-2
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
_______________________________________________________________________________________ 7
IN
R
G
V
OUT
= -(RF / RG) V
IN
R
F
V
OUT_
MAX403_E
R
L
150Ω
Figure 2. Inverting Gain Configuration
IN_+
R
G
V
OUT
= [1+ (RF / RG)] V
IN_+
R
F
V
OUT_
MAX403_E
R
L
150Ω
Figure 1. Noninverting Gain Configuration
Figure 3. Driving a Capacitive Load Through an Isolation Resistor
R
F
24Ω
R
ISO
C
L
V
OUT_
V
IN_+
MAX403_E
MAX4030E/MAX4031E
Human Body Model
Figure 8 shows the Human Body Model and Figure 9
shows the current waveform it generates when discharged into low impedance. This model consists of a
150pF capacitor charged to the ESD voltage of interest,
and then discharged into the test device through a
1.5kΩ resistor.
IEC 1000-4-2
The IEC 1000-4-2 standard covers ESD testing and performance of finished equipment; it does not specifically
refer to ICs. The MAX4030E/MAX4031E enable the
design of equipment that meets the highest level (level
4) of IEC 1000-4-2 without the need for additional ESD
protection components. The major difference between
tests done using the Human Body Model and IEC 10004-2 is higher peak current in IEC 1000-4-2. Because
series resistance is lower in the IEC 1000-4-2 model, the
ESD-withstand voltage measured to this standard is generally lower than that measured using the Human Body.
Figure 10 shows the IEC 1000-4-2 model and Figure 11
shows the current waveform for the ±8kV IEC 1000-4-2
level 4 ESD Contact Discharge test. The Air-Gap test
involves approaching the device with a charged probe.
The Contact Discharge method connects the probe to
the device before the probe is energized.
Chip Information
MAX4030E TRANSISTOR COUNT: 271
MAX4031E TRANSISTOR COUNT: 387
PROCESS: BiCMOS
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
8 _______________________________________________________________________________________
ISOLATION RESISTANCE
vs. CAPACITIVE LOAD
CAPACITIVE LOAD (pF)
R
ISO
(Ω)
400300200100
2
4
6
8
10
12
14
16
18
20
0
0 500
Figure 4. Isolation Resistance vs. Capacitive Load
SMALL-SIGNAL GAIN vs. FREQUENCY WITH LOAD
CAPACITANCE AND NO ISOLATION RESISTOR
FREQUENCY (MHz)
GAIN (dB)
100101
-3
-4
-5
-2
-1
0
1
2
3
4
5
6
-6
0.1 1000
CL = 20pF
CL = 10pF
CL = 5pF
Figure 5. Small-Signal Gain vs. Frequency with Load
Capacitance and No Isolation Resistor
SMALL-SIGNAL GAIN vs. FREQUENCY WITH LOAD
CAPACITANCE AND 10Ω ISOLATION RESISTOR
FREQUENCY (MHz)
GAIN (dB)
100101
-3
-4
-5
-2
-1
0
1
2
3
4
5
6
-6
0.1 1000
CL = 20pF
CL = 10pF
CL = 5pF
Figure 6. Small-Signal Gain vs. Frequency with Load
Capacitance and 10Ω Isolation Resistor
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
_______________________________________________________________________________________ 9
HIGH-
VOLTAGE
DC
SOURCE
CHARGE CURRENT
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
RD = 1.5kΩ
R
C
= 1MΩ
C
S
= 150pF
DEVICE
UNDER
TEST
Figure 8. Human Body ESD Model
IP 100%
90%
36.8%
t
RL
TIME
t
DL
CURRENT WAVEFORM
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
I
r
10%
0
0
AMPERES
Figure 9. Human Body Current Waveform
tr = 0.7ns TO 1ns
30ns
60ns
t
100%
90%
10%
I
PEAK
I
Figure 11. IEC 1000-4-2 ESD Generator Current Waveform
CHARGE CURRENT
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
C
S
150pF
R
C
50MΩ TO
100M
Ω
R
D
330
Ω
HIGH-
VOLTAGE
DC
SOURCE
DEVICE
UNDER
TEST
Figure 10. IEC 1000-4-2 ESD Test Model
200Ω
200Ω
75Ω
MAX403_E
5V
C
BYPASS
0.1µF
75Ω
TEST
POINT B
TEST
POINT A
V
EE
Figure 7. ESD Test Circuit
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
10 ______________________________________________________________________________________
8LUMAXD.EPS
PACKAGE OUTLINE, 8L uMAX/uSOP
1
1
21-0036
J
REV.DOCUMENT CONTROL NO.APPROVAL
PROPRIETARY INFORMATION
TITLE:
MAX
0.043
0.006
0.014
0.120
0.120
0.198
0.026
0.007
0.037
0.0207 BSC
0.0256 BSC
A2
A1
c
e
b
A
L
FRONT VIEW
SIDE VIEW
E H
0.6±0.1
0.6±0.1
Ø0.50±0.1
1
TOP VIEW
D
8
A2
0.030
BOTTOM VIEW
1
6∞
S
b
L
H
E
D
e
c
0∞
0.010
0.116
0.116
0.188
0.016
0.005
8
4X S
INCHES
-
A1
A
MIN
0.002
0.950.75
0.5250 BSC
0.25 0.36
2.95 3.05
2.95 3.05
4.78
0.41
0.65 BSC
5.03
0.66
6∞0∞
0.13 0.18
MAX
MIN
MILLIMETERS
- 1.10
0.05 0.15
α
α
DIM
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages
.)
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
______________________________________________________________________________________ 11
TSSOP4.40mm.EPS
PACKAGE OUTLINE, TSSOP 4.40mm BODY
21-0066
1
1
G
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages
.)
MAX4030E/MAX4031E
Low-Cost, 144MHz, Dual/Triple Op Amps
with ±15kV ESD Protection
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2005 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc.
SOICN .EPS
PACKAGE OUTLINE, .150" SOIC
1
1
21-0041
B
REV.DOCUMENT CONTROL NO.APPROVAL
PROPRIETARY INFORMATION
TITLE:
TOP VIEW
FRONT VIEW
MAX
0.010
0.069
0.019
0.157
0.010
INCHES
0.150
0.007
E
C
DIM
0.014
0.004
B
A1
MIN
0.053A
0.19
3.80 4.00
0.25
MILLIMETERS
0.10
0.35
1.35
MIN
0.49
0.25
MAX
1.75
0.050
0.016L
0.40 1.27
0.3940.386D
D
MINDIM
D
INCHES
MAX
9.80 10.00
MILLIMETERS
MIN
MAX
16
AC
0.337 0.344 AB8.758.55 14
0.189 0.197 AA5.004.80 8
N MS012
N
SIDE VIEW
H0.2440.228 5.80 6.20
e0.050 BSC 1.27 BSC
C
HE
e
B
A1
A
D
0∞-8∞
L
1
VARIATIONS:
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages
.)
Loading...