Maxim MAX3875E-D Datasheet

General Description
The MAX3875 is a compact, low-power clock recovery and data retiming IC for 2.488Gbps SDH/SONET appli­cations. The fully integrated phase-locked loop recov­ers a synchronous clock signal from the serial NRZ data input, which is retimed by the recovered clock. Differential PECL-compatible outputs are provided for both clock and data signals, and an additional
2.488Gbps serial input is available for system loopback diagnostic testing. The device also includes a TTL­compatible loss-of-lock (LOL) monitor.
The MAX3875 is designed for both section-regenerator and terminal-receiver applications in OC-48/STM-16 transmission systems. Its jitter performance exceeds all of the SONET/SDH specifications.
This device operates from a single +3.3V to +5.0V supply over a -40°C to +85°C temperature range. The typical power consumption is only 400mW with a +3.3V supply. It is available in a 32-pin TQFP package, as well as in die form.
Applications
SDH/SONET Receivers and Regenerators Add/Drop Multiplexers Digital Cross-Connects
2.488Gbps ATM Receiver Digital Video Transmission SDH/SONET Test Equipment
Features
Exceeds ANSI, ITU, and Bellcore SONET/SDH
Regenerator Specifications
400mW Power Dissipation (at +3.3V)Clock Jitter Generation: 0.003UI
RMS
Single +3.3V or +5V Power SupplyFully Integrated Clock Recovery and Data RetimingAdditional High-Speed Input Facilitates System
Loopback Diagnostic Testing
Tolerates >2000 Consecutive Identical DigitsLoss-of-Lock IndicatorDifferential PECL-Compatible Data and Clock
Outputs
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 1-800-835-8769.
MAX3875
2.5Gbps, Low-Power, +3.3V
Clock Recovery and Data Retiming IC
________________________________________________________________
Maxim Integrated Products
1
PRE/POSTAMPLIFIER
PHOTO­DIODE
+3.3V
SDI-
SDI+
SLBI­SLBI+
SDO-
SCLKO+
SCLKO-
SDO+
MAX3875
MAX3866
+3.3V
+3.3V
+3.3V
+3.3V
OUT+
OUT-
TTL
LOP
IN
LOLPHADJ-PHADJ+V
CC
V
CC
SIS FIL+ FIL-
SYSTEM
LOOPBACK
TTL
TTL
1µF
0.01µF
0.01µF
82 82
130130
82 82
130130
1:16
DESERIALIZER
MAX3885
Typical Application Circuit
19-4789; Rev 0; 10/98
PART
MAX3875EHJ -40°C to +85°C
TEMP. RANGE PIN-PACKAGE
32 TQFP
Ordering Information
Pin Configuration appears at end of data sheet.
MAX3875E/D -40°C to +85°C Dice*
*
Dice are designed to operate over this range, but are tested and guaranteed at TA= +25°C only. Contact factory for availability.
MAX3875
2.5Gbps, Low-Power, +3.3V Clock Recovery and Data Retiming IC
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
DC ELECTRICAL CHARACTERISTICS
(VCC= +3.0V to +5.5V, TA= -40°C to +85°C, unless otherwise noted. Typical values are at +3.3V and TA= +25°C.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Supply Voltage, VCC..............................................-0.5V to +7.0V
Input Voltage Levels
(SDI+, SDI-, SLBI+, SLBI-)...........(V
CC
- 0.5V) to (VCC+ 0.5V)
Input Current Levels (SDI+, SDI-, SLBI+, SLBI-)..............±10mA
PECL Output Voltage
(SDO+, SDO-, SCLKO+, SCLKO-).......................(V
CC
+ 0.5V)
PECL Output Current, (SDO+, SDO-, SCLKO+, SCLKO-).....56mA
Voltage at LOL, SIS, PHADJ+, PHADJ-,
FIL+, FIL-.................................................-0.5V to (V
CC
+ 0.5V)
Continuous Power Dissipation (T
A
= +85°C)
TQFP (derate 16.1mW/°C above +85°C)........................1.0W
Operating Temperature Range
MAX3875EHJ..................................................-40°C to +85°C
Operating Junction Temperature (die)..............-55°C to +150°C
Storage Temperature Range.............................-60°C to +160°C
Processing Temperature (die).........................................+400°C
Lead Temperature (soldering, 10sec).............................+300°C
Figure 1
Excluding PECL output termination
TA= 0°C to +85°C
TA= 0°C to +85°C
CONDITIONS
VVCC- 0.4 VCC+ 0.2V
IS
Single-Ended Input Voltage (SDI±, SLBI±)
mVp-p50 800 V
ID
mA122 167I
CC
Supply Current Differential Input Voltage
(SDI±, SLBI±)
V2.4 V
CC
V
OH
TTL Output High Voltage (LOL)
µA-10 +10TTL Input Current (SIS)
V0.8V
IL
TTL Input Low Voltage (SIS)
45R
IN
Input Termination to V
CC
(SDI±, SLBI±)
V
VCC- 1.025 VCC- 0.88
V
OH
PECL Output High Voltage (SDO±, SCLKO±)
V
VCC- 1.81 VCC- 1.62
V
OL
PECL Output Low Voltage (SDO±, SCLKO±)
V2.0V
IH
TTL Input High Voltage (SIS)
UNITSMIN TYP MAXSYMBOLPARAMETER
TTL Output Low Voltage (LOL)
V
OL
0.4 V
VCC- 1.085 VCC- 0.88
VCC- 1.83 VCC- 1.555
TA = -40°C
TA = -40°C
Figure 1. Input Amplitude Figure 2. Output Clock-to-Q Delay
SCLKO+
SDO
t
CK
t
CK-Q
Note 1: Dice are tested at TA= +25°C only.
SDI+
SDI-
(SDI+) -
(SDI-)
V
ID
25mV MIN 400mV MAX
50mVp-p MIN 800mVp-p MAX
MAX3875
2.5Gbps, Low-Power, +3.3V
Clock Recovery and Data Retiming IC
_______________________________________________________________________________________ 3
AC ELECTRICAL CHARACTERISTICS
(VCC= +3.0V to +5.5V, TA= -40°C to +85°C, unless otherwise noted. Typical values are at +3.3V and TA= +25°C.) (Note 2)
Clock Output Edge Speed 20% to 80%
f 2MHz
70 ps
Figure 2
1.76 2.75
0.21 0.45
f = 100kHz
f = 10MHz (Note 3)
f = 70kHz
f = 1MHz
CONDITIONS
dB0.1J
P
Jitter Peaking
ps110 290
Gbps2.488Serial Output Clock Rate
Clock-to-Q Delay
UIp-p0.026 0.056
UI
RMS
0.003 0.006
J
GEN
Jitter Generation
MHz1.1 2.0J
BW
Jitter Transfer Bandwidth
UIp-p
1.91 3.6
Jitter Tolerance
0.41 0.67
UNITSMIN TYP MAXSYMBOLPARAMETER
Data Output Edge Speed 20% to 80% 108 ps Tolerated Consecutive
Identical Digits
2000
Bits
100kHz to 2.5GHz -17
2.5GHz to 4.0GHz -15
Jitter BW = 12kHz to 20MHz
Note 2: AC characteristics are guaranteed by design and characterization. Note 3: See
Typical Operating Characteristics
for worst-case distribution.
Input Return Loss (SDI±, SLBI±)
dB
Typical Operating Characteristics
(VCC= +3.3V, TA = +25°C, unless otherwise noted.)
RECOVERED CLOCK JITTER
MAX3875 toc02
10ps/div
PRBS = 2
15
- 1
RMS = 1.2ps
0.1 10k 10M100k 1M
JITTER TOLERANCE
1
10
MAX3875 toc03
JITTER FREQUENCY (Hz)
INPUT JITTER (UIp-p)
PRBS = 223 - 1 50mVp-p INPUT
BELLCORE MASK
RECOVERED DATA AND CLOCK
(DIFFERENTIAL OUTPUT)
MAX3875 toc01
100ps/div
CLOCK
DATA
2
23
- 1 PATTERN
V
IN
= 20mV
P-P
TA = +85°C
Loading...
+ 5 hidden pages