Maxim MAX3093ECPE Datasheet

________________General Description

The MAX3093E/MAX3094E are rugged, low-power,
quad, RS-422/RS-485 receivers featuring electrostatic
discharge (ESD) protection for use in harsh environ­ments. All receiver inputs are protected to ±15kV using
IEC 1000-4-2 Air-Gap Discharge, ±8kV using IEC 1000­4-2 Contact Discharge, and ±15kV using the Human
Body Model. The MAX3093E operates from a +5V sup­ply, while the MAX3094E operates from a +3.3V supply.
Receiver propagation delays are guaranteed to within
±8ns of a predetermined value, thereby ensuring
device-to-device matching across production lots.

The devices feature a 1nA low-power shutdown mode
in which the receiver outputs are high impedance.
When active, these receivers have a fail-safe feature
that guarantees a logic-high output if the input is open
circuit. They also have a quarter-unit-load input imped­ance that allows 128 receivers on a bus.

The MAX3093E/MAX3094E are pin-compatible, low­power upgrades to the industry-standard ’34C86. They
are available in space-saving TSSOP, narrow SO, and
PDIP packages.

________________________Applications

Telecommunications Equipment

Rugged RS-422/RS-485/RS-423 Bus Receiver

Receivers for ESD-Sensitive Applications

Level Translators

____________________________Features

♦ ESD Protection

±15kV—IEC 1000-4-2 Air-Gap Discharge
±8kV—IEC 1000-4-2 Contact Discharge
±15kV—Human Body Model

♦ Guaranteed Propagation-Delay Tolerance

Between All ICs

±8ns (MAX3093E)
±10ns (MAX3094E)

♦ Single +3V Operation (MAX3094E)

Single +5V Operation (MAX3093E)

♦ 16-Pin TSSOP
♦ 10Mbps Data Rate
♦ Allow up to 128 Receivers on the Bus
♦ 1nA Low-Power Shutdown Mode
♦ 2.4mA Operating Supply Current
♦ Pin-Compatible Upgrades to

’

34C86

MAX3093E/MAX3094E

±15kV ESD-Protected, 10Mbps, 3V/5V,

Low-Power Quad RS-422/RS-485 Receivers

________________________________________________________________ Maxim Integrated Products 1

Pin Configuration

YA

YB

YC

YD

A+

A-

B+

B-

C+

C-

D+

D-

MAX3093E
MAX3094E

V

CC

GND

ENBD

ENAC

A

B

C

D

________________Functional Diagram

19-1779; Rev 2; 10/02

PART

MAX3093ECUE

MAX3093ECSE
MAX3093ECPE 0°C to +70°C

0°C to +70°C

0°C to +70°C

TEMP RANGE PIN-PACKAGE

16 TSSOP
16 Narrow SO
16 Plastic DIP

_______________Ordering Information

MAX3093EEUE
MAX3093EESE
MAX3093EEPE -40°C to +85°C

-40°C to +85°C

-40°C to +85°C 16 TSSOP
16 Narrow SO
16 Plastic DIP

MAX3094ECUE
MAX3094ECSE
MAX3094ECPE 0°C to +70°C

0°C to +70°C

0°C to +70°C 16 TSSOP

16 Narrow SO
16 Plastic DIP

MAX3094EEUE
MAX3094EESE
MAX3094EEPE -40°C to +85°C

-40°C to +85°C

-40°C to +85°C 16 TSSOP
16 Narrow SO
16 Plastic DIP

For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.

TOP VIEW

1

A- V

A

A+

2

YA

3

MAX3093E

4

ENAC

YC

C

C+

C-

GND

MAX3094E

5

6

7

8

TSSOP/SO/DIP

16

CC

B-

15

B

B+

14

YB

13

ENBD

12

YD

11

D

D+

10

D-

9

MAX3093E/MAX3094E

±15kV ESD-Protected, 10Mbps, 3V/5V,
Low-Power Quad RS-422/RS-485 Receivers

2 _______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

DC ELECTRICAL CHARACTERISTICS—MAX3093E

(VCC= +5V ±5%, TA= T

MIN

to T

MAX

, unless otherwise noted. Typical values are at VCC= +5.0V, TA= +25°C.) (Note 1)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.

Supply Voltage (VCC).............................................................+7V

Control Input Voltage (ENAC, ENBD).........-0.3V to (V

CC

+ 0.3V)

Receiver Input Voltage (_+, _-)............................................±25V

Receiver Output Voltage (Y_).....................-0.3V to (V

CC

+ 0.3V)

Output Short-Circuit Duration (Y_, one output) ..........Continuous

Continuous Power Dissipation (T

A

= +70°C)

TSSOP (derate 9.4mW/°C above +70°C) ....................755mW

SO (derate 8.7mW/°C above +70°C)...........................696mW

Plastic DIP (derate 10.5mW/°C above +70°C) ............762mW

Operating Temperature Ranges

MAX309_EC_ _ ..................................................0°C to +70°C

MAX309_EE_ _ ...............................................-40°C to +85°C

Junction Temperature......................................................+150°C

Storage Temperature Range .............................-65°C to +160°C

Lead Temperature (soldering, 10s) .................................+300°C

VCM= 0

IE C1000-4-2 Contact Discharge

-7V ≤ VCM≤ 12V

IE C1000-4-2 Air-Gap Discharge

Human Body Model

-7V ≤ VCM≤ 12V

0 ≤ V

OUT

≤ VCC, output enabled

0 ≤ V

OUT

≤ VCC, output disabled

I

OUT

= 4mA, VID= -200mV,

output enabled, Figure 1

Output disabled

I

OUT

= -4mA, VID= 200mV,

output enabled, Figure 1

No load, output enabled

CONDITIONS

±8

±15

kV

±15

ESD Protection
(Note 2)

µA0.001 10

mA2.4 3.5

I

CC

Supply Current

mV45

mV-200 200V

TH

Receiver Differential Input
Threshold

Receiver Input Hysteresis

kΩ48R

IN

Receiver Input Resistance

mA±7 ±75I

OSR

Output Short-Circuit Current

µA±1I

OZR

Three-State Current at Receiver
Output

V0.4V

OL

Receiver Output Low Voltage

µA±1

Enable Input Current
(ENAC/ENBD)

V2.0V

IH

Enable Input High Voltage
(ENAC/ENBD)

V0.8V

IL

Enable Input Low Voltage
(ENAC/ENBD)

VVCC- 1.5V

OH

Receiver Output High Voltage

UNITSMIN TYP MAXSYMBOLPARAMETER

µA

250

I

IN

Receiver Input Current (_+, _-) VCC= 0 or 5.25V

VIN= 12V

-200VIN= -7V

MAX3093E/MAX3094E

±15kV ESD-Protected, 10Mbps, 3V/5V,

Low-Power Quad RS-422/RS-485 Receivers

_______________________________________________________________________________________ 3

DC ELECTRICAL CHARACTERISTICS—MAX3094E

(VCC= +3.0V to +3.6V, TA= T

MIN

to T

MAX

, unless otherwise noted. Typical values are at VCC= +3.3V, TA= +25°C.) (Note 1)

SWITCHING CHARACTERISTICS—MAX3093E

(VCC= +5V ±5%, TA= T

MIN

to T

MAX

, unless otherwise noted. Typical values are at VCC= +5.0V, TA= +25°C.)

VCM= 0

-7V ≤ VCM≤ 12V

I

OUT

= -1.5mA, VID= 200mV,

output enabled, Figure 1

CONDITIONS

mV45

mV-200 200V

TH

Receiver Differential Input
Threshold

Receiver Input Hysteresis

µA±1

Enable Input Current
(ENAC/ENBD)

V2.0V

IH

Enable Input High Voltage
(ENAC/ENBD)

V0.8V

IL

Enable Input Low Voltage
(ENAC/ENBD)

VVCC- 0.4V

OH

Receiver Output High Voltage

UNITSMIN TYP MAXSYMBOLPARAMETER

µA

250

I

IN

Receiver Input Current (_+, _-) VCC= 0 or 3.6V

VIN= 12V

-200VIN= -7V

Figure 2 ns-2 ±10

|VID| = 3V,

Figure 2

t

SK

Propagation-Delay Skew
(t

PLH

- t

PHL

)

VCC= +5V ±5%, TA= T

MIN

to T

MAX

VCC= 5.25V

VCC= 4.75V

Figure 3

Figure 3

|

V

ID

|

= 3V, Figure 2, matched conditions

TA= +85°C

TA= +25°C

TA= -40°C

TA= +85°C

Figure 3

TA= +25°C

Figure 3

CONDITIONS

TA= -40°C

t

PLH

, t

PHL

Input-to-Output Propagation
Delay

ns

TA= +70°C 76 92

TA= +70°C 80 96

Mbps10f

MAX

Maximum Data Rate

ns60 100t

HZ

Output Disable Time from
High Level

ns60 100t

LZ

Output Disable Time from
Low Level

78 86 94

65 98

ns600 800t

ZH

Output Enable Time to
High Level

ns600 800t

ZL

Output Enable Time to
Low Level

ns16

Device-to-Device Propagation­Delay Matching

68 76 84

71 79 87

65 73 81

82 90 98

74 82 90

UNITSMIN TYP MAXSYMBOLPARAMETER

MAX3093E/MAX3094E

±15kV ESD-Protected, 10Mbps, 3V/5V,
Low-Power Quad RS-422/RS-485 Receivers

4 _______________________________________________________________________________________

IEC 1000-4-2 Contact Discharge

IEC 1000-4-2 Air-Gap Discharge

Human Body Model

Outputs disabled

No load, outputs enabled

CONDITIONS

±8

±15

kV

±15

ESD Protection
(Note 2)

µA0.001 10

mA2.4 4.0

I

CC

Supply Current

UNITSMIN TYP MAXSYMBOLPARAMETER

DC ELECTRICAL CHARACTERISTICS—MAX3094E (continued)

(VCC= +3.0V to +3.6V, TA= T

MIN

to T

MAX

, unless otherwise noted. Typical values are at VCC= +3.3V, TA= +25°C.) (Note 1)

VCC= +3.3V ±5%, TA= T

MIN

to T

MAX

Figure 3

Figure 3

|VID| = 3V, Figure 2, matched conditions

Figure 3

Figure 3

CONDITIONS

Mbps10f

MAX

Maximum Data Rate

ns80 180t

HZ

Output Disable Time from
High Level

ns80 180t

LZ

Output Disable Time from
Low Level

88 98 108

69 123

ns600 1000t

ZH

Output Enable Time to
High Level

ns600 1000t

ZL

Output Enable Time to
Low Level

ns20

Device-to-Device Propagation­Delay Matching

82 92 102

78 88 98

69 79 89

103 113 123

91 101 111

UNITSMIN TYP MAXSYMBOLPARAMETER

SWITCHING CHARACTERISTICS—MAX3094E

(VCC= +3.0V to +3.6V, TA= T

MIN

to T

MAX

, unless otherwise noted. Typical values are at VCC= +3.3V, TA= +25°C.)

Note 1: All currents into the device are positive; all currents out of the device are negative. All voltages are referred to device

ground, unless otherwise noted.

Note 2: Receiver inputs (_+, _-).

Figure 2 ns-1 ±10t

SK

Propagation-Delay Skew
(t

PLH

- t

PHL

)

TA= +85°C

TA= +25°C

TA= -40°C

TA= +85°C

TA= +25°C

TA= -40°C

R

IN

Receiver Input Resistance -7V ≤ VCM≤ 12V kΩ48

V

OL

Receiver Output Low Voltage

I

OUT

= 2.5mA, VID= -200mV,

output enabled, Figure 1

V0.4

VCC= 3.60V

VCC= 3.00V

t

PLH

, t

PHL

Input-to-Output Propagation
Delay

ns

TA= +70°C 86 106

TA= +70°C 100 120

|VID| = 3V,

Figure 2

I

OSR

Output Short-Circuit Current 0 ≤ V

OUT

≤ VCC, output enabled mA±4 ±60

I

OZR

Three-State Current at Receiver
Output

0 ≤ V

OUT

≤ VCC, output disabled µA±1