MAXIM DS1631, DS1631A, DS1731 User Manual

Download

SDA

www.maxim-ic.com

FEATURES

 DS1631 and DS1631A Provide ±0.5°C

Accuracy over a 0°C to +70°C Range

 DS1731 Provides ±1°C Accuracy over a

-10°C to +85°C Range

 DS1631A Automatically Begins Taking

Temperature Measurements at Power-Up

 Operating Temperature Range: -55°C to

+125°C (-67°F to +257°F)

 Temperature Measurements Require No

External Components

 Output Resolution is User-Selectable to 9,

10, 11, or 12 Bits

 Wide Power-Supply Range (+2.7V to +5.5V)  Converts Temperature-to-Digital Word in

750ms (max)

 Multidrop Capability Simplifies Distributed

Temperature-Sensing Applications

 Thermostatic Settings are User-Definable

and Nonvolatile (NV)

 Data is Read/Written Through 2-Wire Serial

Interface (SDA and SCL Pins)

 All Three Devices are Available in 8-Pin

μSOP Packages and the DS1631 is Also Available in a 150mil SO package—see Table 1 for Ordering Information

DESCRIPTION

DS1631/DS1631A/DS1731

High-Precision Digital

Thermometer and Thermostat

PIN CONFIGURATIONS

OUT

GND

(DS1631U+, DS1631AU+,

OUT

GND

SO (150mil and 208mil)

(DS1631Z+, DS1631S+)

See Table 2 for Pin Descriptions

APPLICATIONS

 Network Routers and Switches  Cellular Base Stations  Portable Products  Any Space-Constrained Thermally Sensitive

Product

DS1731U+)

SOP

VDD A

The DS1631, DS1631A, and DS1731 digital thermometers provide 9, 10, 11, or 12-bit temperature readings over a -55°C to +125°C range. The DS1631 and DS1631A thermometer accuracy is ±0.5°C from 0°C to +70°C with 3.0V ≤ V

3.0V ≤ V points (T

≤ 5.5V. The thermostat on all three devices provides custom hysteresis with user-defined trip

and TL). The TH and TL registers and thermometer configuration settings are stored in NV

≤ 5.5V, and the DS1731 accuracy is ±1°C from -10°C to +85°C with

EEPROM so they can be programmed prior to installation. In addition, the DS1631A automatically begins taking temperature measurements at power-up, which allows it to function as a stand-alone thermostat. Communication with the DS1631/DS1631A/DS1731 is achieved through a 2-wire serial interface, and three address pins allow up to eight devices to be multidropped on the same 2-wire bus.

Pin descriptions for the DS1631/DS1631A/DS1731 are provided in Table 2 and user-accessible registers are summarized in Table 3. A functional diagram is shown in Figure 1.

1 of 15 102307

Table 1. ORDERING INFORMATION

DS1631/DS1631A/DS1731

ORDERING

NUMBER

DS1631U+ D1631 (See Note) DS1631U+T&R D1631 (See Note)

PACKAGE MARKING

DESCRIPTION

DS1631 in Lead-Free 8-Pin μSOP DS1631 in Lead-Free 8-Pin μSOP, 3000 Piece Tape-and-

Reel

DS1631Z+ DS1631Z (See Note) DS1631 in Lead-Free 150 mil 8-Pin SO DS1631Z+T&R DS1631Z (See Note) DS1631AU+ 1631A (See Note) DS1631AU+T&R 1631A (See Note)

DS1631 in Lead-Free 150 mil 8-Pin SO, 2500 Piece Tapeand-Reel

DS1631A in Lead-Free 8-Pin μSOP DS1631A in Lead-Free 8-Pin μSOP, 3000 Piece Tape-and-

Reel

DS1631S+ DS1631S (See Note) DS1631 in Lead-Free 208 mil 8-Pin SO DS1631S+T&R DS1631S (See Note)

DS1631 in Lead-Free 208 mil 8-Pin SO, 2000 Piece Tape-

and-Reel DS1631+ DS1631 (See Note) DS1631 in Lead-Free 300 mil 8-Pin DIP DS1731U+ D1731 (See Note)

DS1731U+T&R D1731 (See Note) DS1631U D1631

DS1631U/T&R D1631

DS1731 in Lead-Free 8-Pin μSOP

DS1731 in Lead-Free 8-Pin μSOP, 3000 Piece Tape-and-

Reel

DS1631 in 8-Pin μSOP

DS1631 in 8-Pin μSOP, 3000-Piece Tape-and-Reel DS1631Z DS1631Z DS1631 in 150mil 8-Pin SO DS1631Z/T&R DS1631Z DS1631 in 150mil 8-Pin SO, 2500-Piece Tape-and-Reel DS1631AU 1631A DS1631AU/T&R 1631A

DS1631A in 8-Pin μSOP

DS1631A in 8-Pin μSOP, 3000-Piece Tape-and-Reel DS1631S DS1631S DS1631 in 208 mil 8-Pin SO

DS1631S/T&R DS1631S

DS1631 in Lead-Free 208 mil 8-Pin SO, 2000 Piece Tape-

and-Reel DS1631 DS1631 DS1631 in 300 mil 8-Pin DIP DS1731U D1731 DS1731U/T&R D1731

DS1731 in 8-Pin μSOP

DS1731 in 8-Pin μSOP, 3000-Piece Tape-and-Reel

Note: A "+" symbol will also be marked on the package near the Pin 1 indicator

Table 2. DETAILED PIN DESCRIPTION

PIN SYMBOL DESCRIPTION

1 SDA Data Input/Output Pin for 2-Wire Serial Communication Port. Open-Drain. 2 SCL Clock Input Pin for 2-Wire Serial Communication Port. 3 T

Thermostat Output Pin. Push-Pull.

OUT

4 GND Ground Pin 5 A2 Address Input Pin 6 A1 Address Input Pin 7 A0 Address Input Pin 8 VDD Supply Voltage Pin. +2.7V to +5.5V Power-Supply Pin.

2 of 15

DS1631/DS1631A/DS1731

Figure 1. FUNCTIONAL DIAGRAM

VDD

CONFIGURATION REGISTER

ND CONTROL LOGIC

SCL

GND

1 2

ADDRESS

AND

I/O CONTROL

TEMPERATURE SENSOR

and ΔΣ ADC

TEMPERATURE REGISTER

TL REGISTER

DIGITAL

COMPARATOR/LOGIC

ABSOLUTE MAXIMUM RATINGS*

Voltage on any Pin Relative to Ground -0.5V to +6.0V Operating Temperature Range -55°C to +125°C Storage Temperature Range -55°C to +125°C Solder Dip Temperature (10s) See IPC/JEDEC J-STD-020A Specification Reflow Oven Temperature +220°C

* These are stress ratings only and functional operation of the device at these or any other conditions

above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability.

3 of 15

DS1631/DS1631A/DS1731

DC ELECTRICAL CHARACTERISTICS

= 2.7V to 5.5V; TA = -55°C to +125°C.)

PARAMETER SYMBOL CONDITION MIN MAX UNITS NOTES

Supply Voltage VDD 2.7 5.5 V 1

DS1631, DS1631A Thermometer Error

ERR

0°C to +70°C,

3.0V ≤ V 0°C to +70°C,

2.7V ≤ V

≤ 5.5V

< 3.0V

±0.5

±1

°C 2

-55°C to +125°C ±2

DS1731 Thermometer Error

ERR

-10°C to +85°C,

3.0V ≤ V

-10°C to +85°C,

2.7V ≤ V

≤ 5.5V

< 3.0V

±1

±1.5

°C 2

-55°C to +125°C ±2

Low-Level Input Voltage High-Level Input Voltage

Output Voltage Input Current Each

I/O Pin

VIL -0.5 0.3 x VDD V

VIH

3mA sink current 0 0.4 SDA Low-Level

OL1

6mA sink current 0 0.6

OL2

0.4 < V

< 0.9VDD -10 +10 µA

I/O

0.7 x VDD

VDD + 0.3 V

Temperature

Active Supply Current

IDD

conversion

-55°C to +85°C Temperature conversion

1.25

+85°C to +125°C

Standby Supply Current

Output Logic

OUT

Voltage

E2 write 400 Communication only 110

0°C to +70°C 800 nA 4

STBY

VOH 1mA source current 2.4 V 1 T

4mA sink current 0.4 V 1

µA

4 of 15

DS1631/DS1631A/DS1731

AC ELECTRICAL CHARACTERISTICS

= 2.7V to 5.5V; TA = -55°C to +125°C.)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS NOTES

9-bit resolution 93.75

Temperature Conversion Time

SCL Frequency f

10-bit resolution

tTC

11-bit resolution 12-bit resolution

0 400 kHz

SCL

187.5

375

750

Bus Free Time Between a STOP and

1.3 µs 5

BUF

START Condition START and Repeated START Hold Time

HD:STA

0.6 µs 5, 6 from Falling SCL Low Period of SCL t High Period of SCL t

1.3 µs 5

LOW

0.6 µs 5

HIGH

Repeated START Condition Setup Time

SU:STA

0.6 µs 5 to Rising SCL Data-Out Hold Time from Falling SCL Data-In Setup Time to Rising SCL

HD:DAT

SU:DAT

Rise Time of SDA and SCL Fall Time of SDA and SCL STOP Setup Time to Rising SCL

SU:STO

Capacitive Load for Each Bus Line I/O Capacitance C

100 ns 5

tR 20 + 0.1CB 1000 ns 5, 7

tF 20 + 0.1CB 300 ns 5, 7

0.6 µs 5

400 pF

I/O

10 pF

0.9 µs 5

Input Capacitance CI 5 pF Spike Pulse Width that can be Suppressed by

tSP 0 50 ns

Input Filter

NOTES:

1) All voltages are referenced to GND.

2) See Figure 2 for Typical Operating Curves.

3) Specified with T

4) Specified with temperature conversions stopped; T

= 0V or VDD.

5) See Timing Diagram in Figure 3. All timing is referenced to 0.9 x V

6) After this period the first clock pulse is generated.

7) For example, if C

pin open; A0, A1, A2 = 0V or VDD; and f

OUT

= 300pF, then tR[min] = tF[min] = 50ns.

≥ 2Hz.

SCL

pin open; SDA = VDD; SCL = VDD; and A0, A1,

and 0.1 x VDD.

5 of 15

DS1631/DS1631A/DS1731

EEPROM AC ELECTRICAL CHARACTERISTICS

= 2.7V to 5.5V; TA = -55°C to +125°C.)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS

EEPROM Write Cycle Time twr 4 10 ms EEPROM Writes N EEPROM Data Retention t

-55°C to +55°C 50k Writes

EEWR

-55°C to +55°C 10 Years

EEDR

Figure 2. TYPICAL OPERATING CURVES

0.8

0.6

0.4

0.2 0

-0.2

ERROR (°C)

-0.4

-0.6

-0.8 0 10 20 30 40 50 60 70

REFERENCE TEMPERATURE (°C)

DS1631/DS1631A

Mean

-3

0.8

0.6

0.4

0.2 0

-0.2

ERROR (°C)

-0.4

-0.6

-0.8

-3

-10 0 10 20

DS1731

Mean

30 40 50 60 70 80

REFERENCE TEMPERATURE (°C)

Figure 3. TIMING DIAGRAM

All timing is referenced to 0.9 x VDD and 0.1 x VDD.

6 of 15

Table 3. REGISTER SUMMARY

DS1631/DS1631A/DS1731

(USER ACCESS)

Temperature (Read Only)

(Read/Write)

Configuration (Various bits are Read/Write and Read Only—See Table 5)

SIZE

(BYTES)

MEMORY

TYPE

2 SRAM

2 EEPROM

SRAM,

EEPROM

AND POWER-UP STATE

Measured temperature in two’s complement format. Power-up state: -60ºC (1100 0100 0000 0000) Upper alarm trip point in two’s complement format. Factory state: 15ºC (0000 1111 0000 0000) Lower alarm trip point in two’s complement format. Factory state: 10ºC (0000 1010 0000 0000) Configuration and status information. Unsigned data. 6 MSbs = SRAM 2 LSbs (POL and 1SHOT bits) = EEPROM Power-up state: 100011XX (XX = user defined)

OPERATION—MEASURING TEMPERATURE

The DS1631, DS1631A, and DS1731 measure temperature using bandgap-based temperature sensors. A delta-sigma analog-to-digital converter (ADC) converts the measured temperature to a 9-, 10-, 11-, or 12bit (user-selectable) digital value that is calibrated in °C; for °F applications a lookup table or conversion routine must be used. Throughout this data sheet, the term “conversion” is used to refer to the entire temperature measurement and ADC sequence.

The DS1631 and DS1731 always power-up in a low-power idle state, and the Start Convert T command must be used to initiate conversions. The DS1631A begins conversions automatically at power-up in the mode determined by the configuration register’s 1SHOT bit.

The DS1631, DS1631A, and DS1731 can be programmed to perform continuous consecutive conversions (continuous-conversion mode) or to perform single conversions on command (one-shot mode). The conversion mode is programmed through the 1SHOT bit in the configuration register as explained in the CONFIGURATION REGISTER section of this data sheet. In continuous-conversion mode, the DS1631A begins performing continuous conversions immediately at power-up, and the DS1631 and DS1731 begin continuous conversions after a Start Convert T command is issued. For all three devices, consecutive conversions continue to be performed until a Stop Convert T command is issued, at which time the device goes into a low-power idle state. Continuous conversions can be restarted at any time using the Start Convert T command.

In one-shot mode the DS1631A performs a single conversion at power-up, and the DS1631 and DS1731 perform a single temperature conversion when a Start Convert T command is issued. For all three devices, when the conversion is complete the device enters a low-power idle state and remains in that state until a single temperature conversion is again initiated by a Start Convert T command.

The resolution of the output digital temperature data is user-configurable to 9, 10, 11, or 12 bits, corresponding to temperature increments of 0.5°C, 0.25°C, 0.125°C, and 0.0625°C, respectively. The default resolution at power-up is 12 bits, and it can be changed through the R0 and R1 bits in the configuration register. Note that the conversion time doubles for each additional bit of resolution.

After each conversion, the digital temperature is stored as a 16-bit two’s complement number in the twobyte temperature register as shown in Figure 4. The sign bit (S) indicates if the temperature is positive or negative: for positive numbers S = 0 and for negative numbers S = 1. The Read Temperature command

7 of 15

DS1631/DS1631A/DS1731

provides user access to the temperature register. Bits 3 through 0 of the temperature register are hardwired to 0. When the device is configured for 12-bit resolution, the 12 MSbs (bits 15 through 4) of the temperature register contain temperature data. For 11-bit resolution, the 11 MSbs (bits 15 through 5) of the temperature register contain data, and bit 4 is 0. Likewise, for 10-bit resolution, the 10 MSbs (bits 15 through 6) contain data, and for 9-bit the 9 MSbs (bits 15 through 7) contain data, and all unused LSbs contain 0s. Table 4 gives examples of 12-bit resolution output data and the corresponding temperatures.

Figure 4. TEMPERATURE, TH, AND TL REGISTER FORMAT

MS Byte

LS Byte

bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8

S 2

bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0

-1

-2

-3

-4

0 0 0 0

Table 4. 12-BIT RESOLUTION TEMPERATURE/DATA RELATIONSHIP

TEMPERATURE

(°C)

+125 0111 1101 0000 0000 7D00h

+25.0625 0001 1001 0001 0000 1910h

+10.125 0000 1010 0010 0000 0A20h

+0.5 0000 0000 1000 0000 0080h

0 0000 0000 0000 0000 0000h

-0.5 1111 1111 1000 0000 FF80h

-10.125 1111 0101 1110 0000 F5E0h

-25.0625 1110 0110 1111 0000 E6F0h

DIGITAL OUTPUT

(BINARY)

DIGITAL OUTPUT

(HEX)

-55 1100 1001 0000 0000 C900h

OPERATION—THERMOSTAT FUNCTION

The thermostat output (T between the measured digital temperature and user-defined upper and lower thermostat trip points. T remains at the updated value until the next conversion completes. When the measured temperature meets or exceeds the value stored in the upper trip-point register (T until the measured temperature falls below the value stored in the lower trip-point reg ister (TL) (see Figure 5). This allows the user to program any amount of hysteresis into the output response. The active state of T

is user-programmable through the polarity bit (POL) in the configuration register.

OUT

The user-defined values in the TH and TL registers (see Figure 4) must be in two’s complement format with the MSb (bit 15) containing the sign bit (S). The T R1 bits in the configuration register (see Table 6), so the TH and TL resolution matches the output temperature resolution. For example, for 10-bit resolution bits 5 through 0 of the T out as 0 (even if 1s are written to these bits), and the converted temperature is compared to the 10 MSbs of TH and TL.

The T

and TL registers are stored in EEPROM; therefore, they are NV and can be programmed prior to

device installation. Writing to and reading from the TH and TL registers is achieved using the Access TH

8 of 15

) is updated after every temperature conversion, based on a comparison

OUT

), T

and TL resolution is determined by the R0 and

becomes active and remains active

OUT

and TL registers read

OUT

DS1631/DS1631A/DS1731

and Access TL commands. When making changes to the TH and TL registers, conversions should first be stopped using the Stop Convert T command if the device is in continuous conversion mode. Note that if the thermostat function is not used, the TH and TL registers can be used as general-purpose NV memory.

Another thermostat feature is the temperature high and low flags (THF and TLF) in the configuration register. These bits provide a record of whether the temperature has been greater than T

or less than TL

at anytime since the device was powered up. These bits power up as 0s, and if the temperature ever exceeds the T

the TLF bit is set to 1. Once THF and/or TLF has been set, it remains set until overwritten with a 0 by the user or until the power is cycled.

DS1631A STAND-ALONE THERMOSTAT OPERATION

Since the DS1631A automatically begins taking temperature measurements at power-up, it can function as a standalone thermostat (i.e., it can provide thermostatic operation without microcontroller communication). For standalone operation, the NV TH and TL registers and the POL and 1SHOT bits in the configuration register should be programmed to the desired values prior to installation. Since the default conversion resolution at power-up is 12 bits (R1 = 1 and R0 = 1 in the configuration register), the conversion resolution is always 12 bits during standalone thermostat operation.

Figure 5. THERMOSTAT OUTPUT OPERATION

POL = 1 (T

IS ACTIVE HIGH)

OUT

LOGIC 1

OUT

LOGIC 0

TEMP

CONFIGURATION REGISTER

The configuration register allows the user to program various DS1631 options such as conversion resolution, T

polarity, and operating mode. It also provides information to the user about conversion

OUT

status, EEPROM activity, and thermostat activity. The configuration register is arranged as shown in Figure 6 and detailed descriptions of each bit are provided in Table 5. This register can be read from and written to using the Access Config command. When writing to the configuration register, conversions should first be stopped using the Stop Convert T command if the device is in continuous conversion mode. Note that the POL and 1SHOT bits are stored in EEPROM so they can be programmed prior to installation is desired. All other configuration register bits are SRAM and power up in the state shown in Table 5.

Figure 6. CONFIGURATION REGISTER

MSb

it 6

it 5

it 4

it 3

it 2

it 1 LSb

DONE THF TLF NVB R1 R0 POL* 1SHOT*

*NV (EEPROM)

9 of 15

Table 5. CONFIGURATION REGISTER BIT DESCRIPTIONS

BIT NAME

(USER ACCESS)

DONE—Temperature

Conversion Done

(Read Only)

THF—Temperature High Flag (Read/Write)

TLF—Temperature Low Flag (Read/Write)

NVB—NV Memory Busy (Read Only)

R1—Resolution Bit 1 (Read/Write) R0—Resolution Bit 0 (Read/Write)

POL*—T

Polarity

OUT

(Read/Write)

1SHOT*—Conversion Mode (Read/Write)

*Stored in EEPROM

Power-up state = 1. DONE = 0. Temperature conversion is in progress. DONE = 1. Temperature conversion is complete. Power-up state = 0. THF = 0. The measured temperature has not exceeded the value stored in the TH register since power-up. THF = 1. At some point since power-up the measured temperature has been higher than the value stored in the TH register. THF remains a 1 until it is overwritten with a 0 by the user, the power is cycled, or a Software POR command is issued. Power-up state = 0. TLF = 0. The measured temperature has not been lower than the value stored in the T TLF = 1. At some point since power-up the measured temperature has been lower than the value stored in the T 1 until it is overwritten with a 0 by the user, the power is cycled, or a Software POR command is issued. Power-up state = 0. NVB = 1. A write to EEPROM memory is in progress. NVB = 0. NV memory is not busy. Power-up state = 1. Sets conversion, TH, and TL resolution (see Table 6). Power-up state = 1. Sets conversion, TH, and TL resolution (see Table 6). Power-up state = last value written to this bit. Factory setting = 0. POL = 1. T POL = 0. T Power-up state = last value written to this bit. Factory setting = 0. 1SHOT = 1. One-Shot Mode. The Start Convert T command initiates a single temperature conversion and then the device goes into a lowpower standby state. 1SHOT = 0. Continuous Conversion Mode. The Start Convert T command initiates continuous temperature conversions.

FUNCTIONAL DESCRIPTION

is active high.

OUT

is active low.

OUT

DS1631/DS1631A/DS1731

Table 6. RESOLUTION CONFIGURATION

R1 R0

RESOLUTION

(BIT)

0 0 9 93.75ms 0 1 10 187.5ms 1 0 11 375ms 1 1 12 750ms

10 of 15

CONVERSION TIME

(MAX)

DS1631/DS1631A/DS1731

2-WIRE SERIAL DATA BUS

The DS1631, DS1631A, and DS1731 communicate over a bidirectional 2-wire serial data bus that consists of a serial clock (SCL) signal and serial data (SDA) signal. The DS1631, DS1631A, and DS1731 interface to the bus through their SCL input pins and open-drain SDA I/O pins.

The following terminology is used to describe 2-wire communication: Master Device: Microprocessor/microcontroller that controls the slave devices on the bus. The master

device generates the SCL signal and START and STOP conditions. Slave: All devices on the bus other than the master. The DS1631, DS1631A, and DS1731 always

function as slaves. Bus Idle or Not Busy: Both SDA and SCL remain high. SDA is held high by a pullup resistor when the

bus is idle, and SCL must either be forced high by the master (if the SCL output is push-pull) or pulled high by a pullup resistor (if the SCL output is open-drain).

Transmitter: A device (master or slave) that is sending data on the bus. Receiver: A device (master or slave) that is receiving data from the bus. START Condition: Signal generated by the master to indicate the beginning of a data transfer on the

bus. The master generates a START condition by pulling SDA from high to low while SCL is high (see Figure 8). A “repeated” START is sometimes used at the end of a data transfer (instead of a STOP) to indicate that the master will perform another operation.

STOP Condition: Signal generated by the master to indicate the end of a data transfer on the bus. The master generates a STOP condition by transitioning SDA from low to high while SCL is high (see Figure

8). After the STOP is issued, the master releases the bus to its idle state. Acknowledge (ACK): When a device is acting as a receiver, it must generate an acknowledge (ACK) on

the SDA line after receiving every byte of data. The receiving device performs an ACK by pulling the SDA line low for an entire SCL period (see Figure 8). During the ACK clock cycle, the transmitting device must release SDA. A variation on the ACK signal is the “not acknowledge” (NACK). When the master device is acting as a receiver, it uses a NACK instead of an ACK after the last data byte to indicate that it is finished receiving data. The master indicates a NACK by leaving the SDA line high during the ACK clock cycle.

Slave Address: Every slave device on the bus has a unique 7-bit address that allows the master to access that device. The 7-bit bus address is 1 0 0 1 A2 A1 A0, where A2, A1, and A0 are user-selectable through the corresponding input pins. The three address pins allow up to eight DS1631s, DS1631As, or DS1731s to be multidropped on the same bus.

Control Byte: The control byte is transmitted by the master and consists of the 7-bit slave address plus a read/write (R/

W¯¯) bit (see Figure 7). If the master is going to read data from the slave device then R/W¯¯ =

1, and if the master is going to write data to the slave device then R/W¯¯ = 0.

Command Byte: The command byte can be any of the command protocols described in the COMMAND SET section of this data sheet.

Figure 7. CONTROL BYTE

bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0

1 0 0 1 A

11 of 15

A1 A0

W¯¯

Figure 8. START, STOP, AND ACK SIGNALS

SDA

SCL

DS1631/DS1631A/DS1731

START

Condition

ACK (or NACK)

From Receiver

STOP

Condition

GENERAL 2-WIRE INFORMATION

 All data is transmitted MSb first over the 2-wire bus.  One bit of data is transmitted on the 2-wire bus each SCL period.  A pullup resistor is required on the SDA line and, when the bus is idle, both SDA and SCL must remain

in a logic-high state.

 All bus communication must be initiated with a START condition and terminated with a STOP

condition. During a START or STOP is the only time SDA is allowed to change states while SCL is high. At all other times, changes on the SDA line can only occur when SCL is low: SDA must remain stable when SCL is high.

 After every 8-bit (1-byte) transfer, the receiving device must answer with an ACK (or NACK), which

takes one SCL period. Therefore, nine clocks are required for every one-byte data transfer.

INITIATING 2-WIRE COMMUNICATION

To initiate 2-wire communication, the master generates a START followed by a control byte containing the DS1631, DS1631A, or DS1731 slave address. The R/W¯¯ bit of the control byte must be a 0 (“write”) since the master next writes a command byte. The DS1631/DS1631A/DS1731 responds with an ACK

after receiving the control byte. This must be followed by a command byte from the master, which indicates what type of operation is to be performed. The DS1631/DS1631A/DS1731 again respond with an ACK after receiving the command byte.

If the command byte is a Start Convert T or Stop Convert T command (see Figure 9a), the transaction is finished, and the master must issue a STOP to signal the end of the communication sequence. If the command byte indicates a write or read operation, additional actions must occur as explained in the following sections.

2-WIRE WRITES

The master can write data to the DS1631/DS1631A/DS1731 by issuing an Access Config, Access TH, or Access TL command following the control byte (see Figures 9b and 9d). Since the R/W¯¯ bit in the control byte was a 0 (“write”), the DS1631/DS1631A/DS1731 are already prepared to receive data. Therefore,

after receiving an ACK in response to the command byte, the master device can immediately begin transmitting data. When writing to the configuration register, the master must send one byte of data, and when writing to the T byte, the DS1631/DS1631A/DS1731 respond with an ACK, and the transaction is finished with a STOP from the master.

12 of 15

or TL registers the master must send two bytes of data. After receiving each data

DS1631/DS1631A/DS1731

2-WIRE READS

The master can read data from the DS1631/DS1631A/DS1731 by issuing an Access Config, Access TH, Access TL, or Read Temperature command following the control byte (see Figures 9c and 9e). After receiving an ACK in response to the command, the master must generate a repeated START followed by

a control byte with the same slave address as the first control byte. However, this time the R/

W¯¯ bit must

be a 1, which tells the DS1631/DS1631A/DS1731 that a “read” is being performed. After the DS1631/DS1631A/DS1731 send an ACK in response to this control byte, it begins transmitting the requested data on the next clock cycle. One byte of data will be transmitted when reading from the configuration register after which the master must respond with a NACK followed by a STOP. For twobyte reads (i.e., from the Temperature, T

, or TL register), the master must respond to the first data byte

with an ACK and to the second byte with a NACK followed by a STOP. If only the most significant byte of data is needed, the master can issue a NACK followed by a STOP after reading the first data byte.

COMMAND SET

The DS1631/DS1631A/DS1731 command set is detailed below:

Start Convert T [ 51h ]

Initiates temperature conversions. If the part is in one-shot mode (1SHOT = 1), only one conversion is performed. In continuous mode (1SHOT = 0), continuous temperature conversions are performed until a Stop Convert T command is issued.

Stop Convert T [ 22h ]

Stops temperature conversions when the device is in continuous conversion mode (1SHOT = 0).

Read Temperature [ AAh ]

Reads last converted temperature value from the 2-byte temperature register.

Access TH [ A1h ]

Reads or writes the 2-byte TH register.

Access TL [ A2h ]

Reads or writes the 2-byte TL register.

Access Config [ ACh ]

Reads or writes the 1-byte configuration register.

Software POR [ 54h ]

Initiates a software power-on-reset (POR), which stops temperature conversions and resets all registers and logic to their power-up states. The software POR allows the user to simulate cycling the power without actually powering down the device.

13 of 15

Figure 9 (a, b, c, d, e). 2-WIRE INTERFACE TIMING

THERM = DS1631, DS1631A, or DS1731

AD2D6 D5 D4

D1 D0A0

STOP

ACK

(THERM)

Data Byte

(from Master)

NA1S1 1

D2 D1 D0 D3 D4

D6 D5 D7 A

A2 A1 A0 1

STOP

NACK

Data Byte

ACK

Control Byte

(Master)

(from THERM)

(THERM)

D1 D2 D0D7D6 D5 D4 D3 D4

D6 D5

D2 D1 D0 D3

STOP

ACK

(THERM)

LS Data Byte

(from Master)

ACK

(THERM)

(from Master)

MS Data Byte

DS1631/DS1631A/DS1731

…

D7 AD2D1D0D6 D5 D4

A2 A1 A0

ACK

(Master)

(from THERM)

ACK

(THERM)

Control Byte MS Data Byte

…

D2 D1 D0 P D3

D5 D6 D4

…

STOP

NACK

(Master)

LS Data Byte

(from THERM)

a) Issue a "Start Convert T” or “Stop Convert T” Command

STOP

ACK

(THERM)

C1 C0 C2 C3

Command Byte

AC7C6C5C4 A

ACK

A2 A1 A0

00 11

SCL

SDA

(THERM)

Control Byte

START

Repeat

START

100AD7A2 1

AA1 1 0 1 0 W

ACK

Command Byte

ACK

(THERM)

100 1

010 A

ACK

(THERM)

Command Byte

ACK

(THERM)

A2 A1 A0

or T

SDA

Control Byte

START

d) Write to the T

Control ByteSTART

S1 100

SCL

b) Write to the Configuration Register

SDA

SCL

c) Read From the Configuration Register

D7 A

(THERM)

C1 C0

Command Byte ACK

C7 C6 C5 C4 A

ACK

A2 A1 A0 C2 1

SCL

Control Byte

0W 0

S 1

START

SDA

, or T

(THERM)

e) Read From the Temperature, T

S 11 AC4

C2 C1C7 C6 C5A2 A1 A0 C3

S 11

SCL

SDA

Repeat

START

ACK

(THERM)

Command Byte

ACK

(THERM)

Control Byte

START

14 of 15

DS1631/DS1631A/DS1731

OPERATION EXAMPLE

In this example, the master configures the DS1631/DS1631A/DS1731 (A1A2A3 = 000) for continuous conversions and thermostatic function.

MASTER

MODE

TX RX START START condition from MASTER. TX RX 90h

RX TX ACK Acknowledge bit from THERMOMETER. TX RX ACh MASTER sends Access Config command. RX TX ACK Acknowledge bit from THERMOMETER.

TX RX 02h

RX TX ACK Acknowledge bit from THERMOMETER. TX RX STOP STOP condition from MASTER. TX RX START START condition from MASTER. TX RX 90h

RX TX ACK Acknowledge bit from THERMOMETER. TX RX A1h MASTER sends Access TH command. RX TX ACK Acknowledge bit from THERMOMETER. TX RX 28h MASTER sends most significant data byte for TH = +40°C. RX TX ACK Acknowledge bit from THERMOMETER. TX RX 00h MASTER sends least significant data byte for TH = +40°C. RX TX ACK Acknowledge bit from THERMOMETER. TX RX STOP STOP condition from MASTER. TX RX START START condition from MASTER. TX RX 90h

RX TX ACK Acknowledge bit from THERMOMETER. TX RX A2h MASTER sends Access TL command. RX TX ACK Acknowledge bit from THERMOMETER. TX RX 0Ah MASTER sends most significant data byte for TL = +10°C. RX TX ACK Acknowledge bit from THERMOMETER. TX RX 00h MASTER sends least significant data byte for TL = +10°C. RX TX ACK Acknowledge bit from THERMOMETER. TX RX STOP STOP condition from MASTER. TX RX START START condition from MASTER. TX RX 90h

RX TX ACK Acknowledge bit from THERMOMETER. TX RX 51h MASTER sends Start Convert T command. RX TX ACK Acknowledge bit from THERMOMETER. TX RX STOP STOP condition from MASTER.

THERMETER*

MODE

DATA

(MSb first)

COMMENTS

MASTER sends control byte with R/W¯¯ = 0.

MASTER writes a data byte to the configuration register to put the THERMOMETER in continuous conversion mode and set the T

polarity to active high.

OUT

MASTER sends control byte with R/W¯¯ = 0.

MASTER sends control byte with R/

W¯¯ = 0.

*THERMOMETER = DS1631, DS1631A, or DS1731

15 of 15

MAXIM DS1631, DS1631A, DS1731 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual