MaxiiCopper Vi2400W Installation Manual

Vi2400W Ethernet Extender over UTP Installation Manual

Vi2400W Powers a PoE Camera:

The MaxiiCopper Model Vi2400W is a transmission device with IP67
weather proof packaging that extends full-duplex high-speed Ethernet and
PoE over existing Coax infrastructures. It extends 10BaseT signals up to
3,000 feet (914m) and 100BaseT up to 1,500 feet (457m). It employs
MaxiiCopper innovative and unique Ethernet extension technology that is
designed to take full advantage of high-bandwidth networking cables and
maintain a full-duplex of 10 or 100 Mb/s Ethernet connection up to the
maximum range with minimum transmission error and latency.

Pass Through PoE (PTP™) eliminates the need for additional remote site
power while allowing a single PoE source, such as a PoE network switch, to
provide power to both transceivers and the camera. This feature eliminates
the need for local and remote site power supplies. The Vi2400W is type
tested under NEMA-TS2 environmental standards for extended temperature
operations between -40C° to +75C°, the Vi2400W is the perfect solution for
extended distance data and power transmission for warehouses, parking
lots, campuses, casinos, and many more.

Installation cost savings, proven performance, and major camera brand
compatibility all go into making Vigitron’s MaxiiCopper™ Vi2400W your best
choice for extended distance data and power transmission.

Important Safety Warning

- Read and keep these instructions.

- Heed all warnings.

- Follow all instructions.

- Do not use this apparatus near water.

- Clean only with a dry cloth.

- Install in accordance with the manufacturer’s instructions.

- This installation should be made by a qualified service person and should conform to all local
codes.

- DO NOT bundle UTP or Coax signals in the same conduit as high-voltage wiring.

- To reduce the risk of fire or electrical shock, do not expose these products to rain, moisture,
dripping or splashing.

- No objects filled with liquids, such as vases, shall be placed on Vigitron equipment.

- DO NOT install the unit in a place where the operating ambient temperature exceeds 75°C or
is below - 40°C.

- Make sure that the external power supply output voltage is in the recommended range.

- Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus that produce heat.

- Protect the power cord from being walked on or pinched particularly at power source,
convenience receptacles, and the point where they exit from the apparatus.

- Only use attachments/accessories specified by the manufacturer.

- Unplug this apparatus during lightning storms or when unused for long periods of time.

- Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as when a power supply cord or plug is damaged, liquid
has been spilled, objects have fallen inside the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.

- The main plug is used as the disconnect device and shall remain readily operable.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,

DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

PoE Switch

Vi2616 Midspan

Data

Network Switch

Data + PoE

Cat5/6

Vi2401A

Data + PoE

Cat5/6

IP Camera-end Installation

Standard Ethernet Connection:

The Vi2400W need to be powered by PoE from the control room side.

- Connect the IP camera RJ45 connector to the “Standard Ethernet” port
of Vi2400W using a standard Cat5/6 cable of maximum 100m in length.

- Connect one end of the UTP cable to the “Standard Ethernet”
waterproof RJ45 connector of Vi2400W.

In order to connect wires to the weatherproff connectors:
a- Unscrew the gasket and insert the UTP cable checking to confirm there is
no spacing between the wire and the insertion hole.
b- Connect the RJ45 cable and insert it into the RJ45 female connector on
the Vi2400W's body making certain the connection is tight.
c- Reconnect the gasket by screwing into the Vi2400W body making certain
to limit any wire slack.

Extended Ethernet Connection:

- Connect one end of the long Coax to waterproof BNC connector of the
“extended Ethernet” port on Vi2400W.

In order to connect wires to the weatherproff connectors:
a- Unscrew the gasket and insert the Coax cable checking to confirm there is
no spacing between the wire and the insertion hole.
b- Connect the BNC connector and insert it into the Coax female connector
on the Vi2400W's body making certain the connection is tight.
c- Reconnect the gasket by screwing into the Vi2400W body making certain
to limit any wire slack. limit any wire slack.

Application Drawing

Data + PoE

Cat5/6

Vi2400W

Ethernet Extenders

Vi2400W

Data + PoE

Cat5/6

Data + PoE

Cat5/6

PoE Camera

PoE Camera

WARNING! - To reduce the risk of fire or electric shock, do not expose this apparatus to
rain or moisture. This apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, such as vases shall be placed on the apparatus.

WARNING! - This apparatus is a Class I product. This product must be connected to a
mains socket outlet thru an AC to DC Power supply.

WARNING! - The mains plug is used as the disconnect device and shall remain readily
operable.

The Smart Choice for Transmission Solutions www.vigitron.com

Ethernet Switch/Midspan-end Installation

The other end of long Coax cable can be connected to several different
Vigitron Extenders. Please follow the installation guide for the selected
device.

UMVi2400W_1017

Technical Specifications

1

Drawings

Electrical

Ethernet Interface Standard 10/100BaseT

Data Rate Auto select 10/100 Mb/s
Full speed / full duplex at maximum rated distance

Coax 1,500 feet (454 m) at 100BaseT with PoE

Power 1.8 W w/POE af/at, 1.5 W
Consumption

Connectors RJ45 x 1
BNC x 1

Surge Protection 6Kv

RFC 2544 TCP/IP Packet Transmission

PoE Compatibility IEEE 802.3af, IEEE 802.3at

RFC 768 UDP, 2068 HTTP, 793 TCP
791 IP, 1783 TFTP, 894 IP over Ethernet

Jumbo Frame Support Yes

Regulatory

FCC Part 15, Subpart , Class B 2010

Emissions EN 5502:2006+A1:2007,
EN 61000-3-2:2006+A1:2009+A2:2009

EN 61000-3-3:2008, EN 55024:1998+A1:2001+A2:2003

Safety CE

Environmental RoHS

6.83" (17.35cm)

3.27" (8.31cm)

Top View

Vi2400W

Weatherproof
Coax Ethernet &
PoE Extender

Made in U.S.A

Front View

1.58"

4.01cm

1.81"

4.59cm

Environmental

Humidity 0 to 95%, non-condensing

Temperature Operating: -40°C to +75°C per NEMA-TS2 testing**
Storage: -40°C to +85°C

Environment IEC60068-252 Salt Laden

Mechanical

Dimensions 1.81x3.27x1.58 in., 4.59x8.31x4.01 cm (HxWxL)

Weight 0.56lb (254g)

Material Extruded Aluminum

**Vigitron "W" are designed as self contained to comply with specific environmental standard. Operating in
conditions other than free air with proper ventilation will affect performance and may void warranty.

Data and PoE Distance

Data Rate

10BaseT

100BaseT

1. Specifications subject to change without notice.

2. Distance figures are obtained using in house testing mirroring installations. Factors

such as cabling, connections, use of power and environmental conditions may affect
actual distances and should be taken into consideration.

3. Specifications reflect operating using Pass Through PoE (PTP™) providing power for
both transceivers and camera from a single source. Distances may increase if
transceivers are locally powered.

4. System can be powered for 802.3af /at using PTP™ reference used is Class 2.

RoHS

Distance

(with POE)

3,000 ft. (914m)

1,500 ft. (457m)

3

2,4

Left Side View

Right Side View

Ordering Information

PART No.

Vi2400W 1-port IP67 Coax Ethernet Extender

Vi2401A 1-port Coax Ethernet Extender

Vi2404A 4-port Coax Ethernet Extender

Vi2408A 8-port Coax Ethernet Extender, 19”, 1U

Vi2416A 16-port Coax Ethernet Extender,19”, 1U

Description

Limited Lifetime Warranty

Vigitron, Inc. warrants that all Vigitron products (“Product”), if used in accordance
with these instructions, will be free of defects in material and workmanship for
lifetime defined as the duration period of time until product end of life is announce­ment. After which Vigitron will continue to provide warranty services for a period of 3
years. Period covering valid warranty will be determined by proof of purchase in the
form of an invoice from an authorized Vigitron dealer.

Warranty will only be provided for as long as the original end user purchaser owns
the product. Warranty is not transferrable. At Vigitron's option, defective product will
be repaired, replaced or substituted with a product of equal value. This warranty
does not apply if, in the judgment of Vigitron, Inc., the Product fails due to damage
from shipment, handling, storage, accident, abuse or misuse, or if it has been used
or maintained not conforming to Product manual instructions, has been modified, or
serial number removed or defaced. Repair by anyone other than Vigitron, Inc. or an
approved agent will void this warranty. Vigitron, Inc. shall not under any circum­stances be liable to any person for any incidental, indirect or consequential
damages, including damages resulting from use or malfunction of the product, loss
of profits or revenues or costs of replacement goods. The maximum liability of
Vigitron, Inc. under this warranty is limited to the original purchase price of the
Product only.

TEL (+1) 858 - 484 - 5209 • FAX (+1) 858 - 484 - 1205

7810 Trade Street, Suite 100, San Diego, CA 92121, USA • [e-mail] • www.vigitron.com

© Copyright 2017 Vigitron, Inc.