Maxell MC-WU5505, MC-WX5501, MC-WU5501, MC-WX5505, MC-X5555 Operating Manual

LCD Projector

MC-WU5505/MC-WU5501/MC-WX5505
MC-WX5501/MC-X5555/MC-X5551

User's Manual (detailed)
Operating Guide – Technical

Supported signals for COMPUTER IN

Resolution (H x V) Signal mode H. frequency

(kHz)
720 x 400 TEXT 37.9 85 VESA
640 x 480 VGA (60Hz) 31.5 59.9 VESA

VGA (72Hz) 37.9 72.8 VESA
VGA (75Hz) 37.5 75 VESA
VGA (85Hz) 43.3 85 VESA

800 x 600 SVGA (56Hz) 35.2 56.3 VESA

SVGA (60Hz) 37.9 60.3 VESA
SVGA (72Hz) 48.1 72.2 VESA
SVGA (75Hz) 46.9 75 VESA
SVGA (85Hz) 53.7 85.1 VESA

832 x 624 Mac 16” mode 49.7 74.5

1024 x 768 XGA (60Hz) 48.4 60 VESA

XGA (70Hz) 56.5 70.1 VESA
XGA (75Hz) 60 75 VESA

XGA (85Hz) 68.7 85 VESA
1152 x 864 1152 x 864 (75Hz) 67.5 75 VESA
1280 x 768 W-XGA (60Hz) 47.7 60 VESA
1280 x 800 1280 x 800 (60Hz) 49.7 60 VESA

1280 x 1024 SXGA (60Hz) 64 60 VESA

SXGA (75Hz) 80 75 VESA

SXGA (85Hz) 91.1 85 VESA

*1) 1366 x 768 WXGA (60Hz) 47.7 59.8 VESA

1440 x 900 WXGA+ (60Hz) 55.9 59.9 VESA
1600 x 900 WXGA++ (60Hz) 60 60 VESA

*2) 1400 x 1050 SXGA+ (60Hz) 65.2 60 VESA
*3) 1680 x 1050 WSXGA+ (60Hz) 65.3 60 VESA

1600 x 1200 UXGA (60Hz) 75 60 VESA
1920 x 1080 Full HD (60Hz) 67.5 60 VESA

*4) 1920 x 1200 W-UXGA (60Hz)

Reduced Blanking

74 60 VESA

V. frequency

(Hz)

Rating

*1) Supported except for [WUXGA Model] *2) Only for [XGA Model]
*3) Only for [WXGA Model], [WUXGA Model] *4) Only for [WUXGA Model]

(continued on next page)

1

QM00112-1

Supported signals

Supported signals for HDMI / HDBaseT

Resolution (H x V) Signal mode H. frequency

(kHz)

V. frequency

(Hz)

Rating

720 x 400 TEXT 37.9 85 VESA
640 x 480 VGA (60Hz) 31.5 59.9 VESA

VGA (72Hz) 37.9 72.8 VESA

VGA (75Hz) 37.5 75 VESA

VGA (85Hz) 43.3 85 VESA
800 x 600 SVGA (56Hz) 35.2 56.3 VESA

SVGA (60Hz) 37.9 60.3 VESA

SVGA (72Hz) 48.1 72.2 VESA

SVGA (75Hz) 46.9 75 VESA

SVGA (85Hz) 53.7 85.1 VESA
832 x 624 Mac 16” mode 49.7 74.5

1024 x 768 XGA (60Hz) 48.4 60 VESA

XGA (70Hz) 56.5 70.1 VESA

XGA (75Hz) 60 75 VESA

XGA (85Hz) 68.7 85 VESA

1152 x 864 1152 x 864 (75Hz) 67.5 75 VESA
1280 x 768 W-XGA (60Hz) 47.7 60 VESA
1280 x 800 1280 x 800 (60Hz) 49.7 60 VESA

1280 x 1024 SXGA (60Hz) 64 60 VESA

SXGA (75Hz) 80 75 VESA

SXGA (85Hz) 91.1 85 VESA

1366 x 768 WXGA (60Hz) 47.7 59.8 VESA
1440 x 900 WXGA+ (60Hz) 55.9 59.9 VESA

1600 x 900 WXGA++ (60Hz) 60 60 VESA
1400 x 1050 SXGA+ (60Hz) 65.2 60 VESA
1680 x 1050 WSXGA+ (60Hz) 65.3 60 VESA
1600 x 1200 UXGA (60Hz) 75 60 VESA

*1) 1920 x 1200 W-UXGA (60Hz)

74 60 VESA

Reduced Blanking

*1) Only for [WUXGA Model]

(continued on next page)

2

QM00112-1

Supported signals

Resolution (H x V) Signal mode H. frequency

(kHz)

V. frequency

(Hz)

Rating

720(1440) x 480i 480i 15.7 60 CEA
720(1440) x 576i 576i 15.6 50 CEA

720 x 480p 480p 31.5 60 CEA

720 x 576p 576p 31.3 50 CEA
1280 x 720p 720p (50Hz) 37.5 50 CEA

720p (60Hz) 45 60 CEA

1920 x 1080i 1080i (50Hz) 28.1 50 CEA

1080i (60Hz) 33.8 60 CEA

1920 x 1080p 1080p (50Hz) 56.3 50 CEA

1080p (60Hz) 67.5 60 CEA

(continued on next page)

3

QM00112-1

Supported signals

Supported signals for MHL

Resolution (H x V) Signal mode H. frequency

(kHz)

V. frequency

(Hz)

Rating

640 x 480 VGA (60Hz) 31.5 59.9 VESA
720(1440) x 480i 480i 15.7 60 CEA
720(1440) x 576i 576i 15.6 50 CEA

720 x 480p 480p 31.5 60 CEA
720 x 576p 576p 31.3 50 CEA

1280 x 720p 720p (50Hz) 37.5 50 CEA

720p (60Hz) 45 60 CEA

1920 x 1080i 1080i (50Hz) 28.1 50 CEA

1080i (60Hz) 33.8 60 CEA

1920 x 1080p 1080p (25Hz) 28.13 25 CEA

1080p (30Hz) 33.75 30 CEA

NOTE • Be sure to check jack type, signal level, timing and resolution

before connecting this projector to a PC.

• Some PCs may have multiple display screen modes. Use of some of these
modes will not be possible with this projector.

• Depending on the input signal, full-size display may not be possible in some
cases. Refer to the number of display pixels above.

• The signal will be converted to the projector’s panel resolution before being
displayed. The best display performance will be achieved if the resolutions of
the input signal and projector panel are identical.

• Automatic adjustment may not function correctly with some input signals.

• The image may not be displayed correctly when the input sync signal is a
composite sync or a sync on G.

• The illustrations in this manual are for illustrative purposes. They may differ
slightly from your projector.

4

QM00112-1

Connection to the ports

Connection to the ports

NOTICE

Ź8VHWKHFDEOHVZLWKVWUDLJKWSOXJVQRW/VKDSHGRQHVDVWKH

input ports of the projector are recessed.

Ź2QO\WKHVLJQDOWKDWLVLQSXWIURPWKHCOMPUTER IN can be output from the
MONITOR OUT port.

MC-WU5505/MC-WX5505/
MC-X5555

A

MC-WU5501/MC-WX5501/
MC-X5551

A

B

B

A

COMPUTER IN, BMONITOR OUT

D-sub 15pin mini shrink jack

⑪⑮⑭⑬⑫

⑥⑩⑨⑧⑦

①⑤④③②

<Computer signal>

9LGHRVLJQDO5*%VHSDUDWH$QDORJ9SSȍWHUPLQDWHGSRVLWLYH

• H/V. sync. signal: TTL level (positive/negative)

• Composite sync. signal: TTL level

<Component video signal>

9LGHRVLJQDO<ZLWKFRPSRVLWHV\QF$QDORJ9SSȍWHUPLQDWHG

&E3E$QDORJ9SSȍWHUPLQDWHG
&U3U$QDORJ9SSȍWHUPLQDWHG

• System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60, 1080p@50/60

Pin Signal Pin Signal

1 Video Red, Cr/Pr 9 (No connection)

2 Video Green, Y 10 Ground

3 Video Blue, Cb/Pb 11 (No connection)

4 (No connection) 12

A

: SDA (DDC data)

B

: (No connection)

5 Ground 13 H. sync / Composite sync.

6 Ground Red, Ground Cr/Pr 14 V. sync.

7 Ground Green, Ground Y

15

A

: SCL (DDC clock)

B

8 Ground Blue, Ground Cb/Pb

5

: (No connection)

QM00112-1

Connection to the ports (continued)

MC-WU5505/MC-WX5505/
MC-X5555

C

MC-WU5501/MC-WX5501/
MC-X5551

F

D

E

C

HDBaseT

RJ-45 jack

F

D

E

④

②⑥⑧

①⑤

③

Pin Signal Pin Signal Pin Signal

1 HDBaseT0+ 4 HDBaseT2+ 7 HDBaseT3+

2 HDBaseT0- 5 HDBaseT2-

8 HDBaseT3-

3 HDBaseT1+ 6 HDBaseT1-

D

HDMI 1 / MHL, EHDMI 2,

F

HDMI OUT

• Type :Digital audio/video connector

• Audio signal: Linear PCM (Sampling rate; 32/44.1/48 kHz)

⑦

④③②⑥⑩

①⑤

⑭⑬⑫⑲⑱⑰⑯

⑨⑧⑦⑪⑮

Pin Signal Pin Signal Pin Signal

T.M.D.S. Data2 +

1

N.C.
T.M.D.S. Data2 Shield

2

CD_SENSE
T.M.D.S. Data2 -

3

N.C.
T.M.D.S. Data1 +

4

N.C.
T.M.D.S. Data1 Shield

5

TMDS_GND
T.M.D.S. Data1 -

6

N.C.
T.M.D.S. Data0 +

7

MHL+

T.M.D.S. Data0 Shield

8

MHL_Shield
T.M.D.S. Data0 -

9

MHL­T.M.D.S. Clock +

10

N.C.
T.M.D.S. Clock Shield

11

TMDS_GND
T.M.D.S. Clock -

12

N.C.
CEC

13

N.C.
Reserved (N.C. on device)

14

N.C.

SCL

15

CD_PULLUP
SDA

16

N.C.
DDC/CEC Ground

17

VBUS_CBUS_GND
+5V Power

18

VBUS
Hot Plug Detect

19

CBUS

6

QM00112-1

MC-WU5505/MC-WX5505/
MC-X5555

Connection to the ports (continued)

H

G

I

J

L

MC-WU5501/MC-WX5501/
MC-X5551

H

L

G

VIDEO

G

I

J

RCA jack

&RPSRVLWHYLGHRVLJQDO$QDORJ9SSȍWHUPLQDWRU

• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL(60Hz)

H

AUDIO IN1

K

K

Ø3.5 stereo mini jack

•

$QDORJNLQSXWLPSHGDQFH

AUDIO IN2 IL, JR

RCA jack x2

•

$QDORJNLQSXWLPSHGDQFH

AUDIO OUT

Ø3.5 stereo mini jack

$QDORJNRXWSXWLPSHGDQFH

•

L

CONTROL

D-sub 9pin plug

* About the details of RS-232C communication,

please refer to the next section.

Pin Signal Pin Signal Pin Signal

K

⑤④③

⑥⑦⑧⑨

①②

1 (No connection) 4 (No connection) 7 RTS

2 RD 5 Ground 8 CTS

3 TD 6 (No connection) 9 (No connection)

7

QM00112-1

Connection to the ports (continued)

MC-WU5505/MC-WX5505/
MC-X5555

MC-WU5501/MC-WX5501/
MC-X5551

M

LAN

O

O

N

M

P

N

M

P

RJ-45 jack

②⑥⑧

①⑤

③

* About the details of network communication,

please refer to the Network Guide.

Pin Signal Pin Signal Pin Signal

1TX+ 4- 7-

2TX- 5-

8-

3RX+ 6RX-

N

WIRELESS

①④③②

Only for USB wireless adapter.

Pin Signal

1+5V

2 - Data

3 + Data

4 Ground

④

⑦

REMOTE CONTROL OIN, POUT

Ø3.5 stereo mini jack

8

QM00112-1

RS-232C Communication

RS-232C Communication

When the projector connects to the computer by RS-232C communication, the
projector can be controlled with RS-232C commands from the computer.

For details of RS-232C commands, refer to RS-232C Communication / Network
command table (

18).

Connection

Turn off the projector and the computer.

1.

Connect the projector's CONTROL port and the computer's RS-232C port

2.

ZLWKD56&FDEOHFURVV8VHWKHFDEOHWKDWIXO¿OOVWKHVSHFL¿FDWLRQ

VKRZQLQ¿JXUH

Turn the computer on, and after the computer has started up turn the projector

3.

on.
Set the COMMUNICATION TYPE to OFF in the COMMUNICATION menu of the

4.

OPTION - SERVICE menu.

RS-232C

RS-232C Cable

(cross)

RS-232C port

of the computer

1

5432

9876

9876

1

5432

CD (1) (1)
RD(2) (2) RD
TD (3) (3) TD
DTR (4) (4)
GND (5) (5) GND
DSR (6) (6)
RTS (7) (7) RTS
CTS (8) (8) CTS
RI (9) (9)

CONTROL

CONTROL port

of the projector

⑥⑦⑧⑨

⑤④③

①②

ٕ

ٕ

ٕ

ٕ

9

QM00112-1

RS-232C Communication (continued)

Communication settings

1. Protocol

19200bps, 8N1

2. Command format

Byte Number

Command

Action

<SET>
desired value [(cL)(cH)]
by [(bL)(bH)].

<GET>
internal setup value [(bL)
(bH)] .

<INCREMENT>
Increment setup value
[(bL)(bH)] by 1.

<DECREMENT>
Decrement setup value
[(bL)(bH)] by 1.

Change setting to

Read projector

01 2 3456

Header

code

LH LHLHLHLHLH

BEh EFh 03h 06h 00h

("h" shows hexadecimal)

Header Data

Packet

Data

size

CRC

ÀDJ

(aL) (aH) 01h 00h (bL) (bH) (cL) (cH)

(aL) (aH) 02h 00h (bL) (bH) 00h 00h

(aL) (aH) 04h 00h (bL) (bH) 00h 00h

(aL) (aH) 05h 00h (bL) (bH) 00h 00h

789101112

Action Type

Setting

code

<EXECUTE> Run a
command [(bL)(bH)].

(aL) (aH) 06h 00h (bL) (bH) 00h 00h

[Header code] [Packet] [Data size]

Set [BEh, EFh, 03h, 06h, 00h] to byte number 0 to 4.

>&5&ÀDJ@

For byte number

table

(18).

5, 6,

refer to

RS-232C Communication / Network command

[Action]

Set functional code to byte number 7, 8.
<SET> = [01h, 00h], <GET> = [02h, 00h], <INCREMENT> = [04h, 00h]
<DECREMENT> = [05h, 00h], <EXECUTE> = [06h, 00h]
Refer to the Communication command table

above).

(

>7\SH@>6HWWLQJFRGH@

For byte number 9 to 12, refer to

18).

command table

(

RS-232C Communication / Network

10

QM00112-1

RS-232C Communication (continued)

3. Response code / Error code

("h" shows hexadecimal)

(1) ACK reply: 06h

When the projector receives the Set, Increment, Decrement or Execute

FRPPDQGFRUUHFWO\WKHSURMHFWRUFKDQJHVWKHVHWWLQJGDWDIRUWKHVSHFL¿HG

item by [Type], and it returns the code.

(2) NAK reply: 15h

When the projector cannot understand the received command, the projector
returns the error code.
In such a case, check the sending code and send the same command again.

(3) Error reply: 1Ch + 0000h

When the projector cannot execute the received command for any reasons,
the projector returns the error code.
In such a case, check the sending code and the setting status of the projector.

(4) Data reply: 1Dh + xxxxh

When the projector receives the GET command correctly, the projector returns
the response code and 2 bytes of data.

NOTE • For connecting the projector to your devices, please read the manual

for each devices, and connect them correctly with suitable cables.

2SHUDWLRQFDQQRWEHJXDUDQWHHGZKHQWKHSURMHFWRUUHFHLYHVDQXQGH¿QHG

command or data.

• Provide an interval of at least 40ms between the response code and any
other code.

• The projector outputs test data when the power supply is switched ON, and
when the lamp is lit. Ignore this data.

• Commands are not accepted during warm-up.

• When the data length is greater than indicated by the data length code, the
projector ignore the excess data code. Conversely when the data length is
shorter than indicated by the data length code, the projector returns the error

code to the computer.

11

QM00112-1

Command Control via the Network

Command Control via the Network

When the projector connects network, the projector can be controlled with RS­232C commands from the computer with web browser.

For details of RS-232C commands, refer to RS-232C Communication / Network
command table

(18).

NOTE •

projector may not be able to process the data correctly.

If data is transferred via wireless and wired LAN at the same time, the

Connection

Turn off the projector and the computer.

1.

If you use wired LAN, connect the projector's LAN or HDBaseTTM port to

2.

the computer's LAN or HDBaseT port with a LAN cable. Use the cable that

IXO¿OOVWKHVSHFL¿FDWLRQVKRZQLQ¿JXUH,I\RXXVHZLUHOHVV/$1LQVHUWWKH86%

wireless adapter into the WIRELESS port of the projector.

Turn the computer on, and after the computer has started up turn the

3.

projector on.

USB wireless adapter

LAN

• LAN cable (CAT-5e or greater)
or

• For HDBaseT connection

- CAT-5e or greater

- shielded type (connectors included)

- straight cable

- single cable

WIRELESS port

LAN or

HDBaseT port

12

QM00112-1

Command Control via the Network

Communication Port

The following two ports are assigned for the command control.

TCP #23
TCP #9715

&RQ¿JXUHWKHIROORZLQJLWHPVIURPDZHEEURZVHUZKHQFRPPDQGFRQWUROLVXVHG

3RUW6HWWLQJV

Click the [Enable] check box to open [Network

Port open

Network Control
Port1 (Port: 23)

Authentication

Control Port1 (Port: 23)] to use TCP #23.
Default setting is "Enable".

Click the [Enable] check box for the
[Authentication] setting when authentication
is required.
Default setting is "Disable".

Click the [Enable] check box to open [Network

Port open

Network Control
Port2 (Port: 9715)

Authentication

Control Port2 (Port: 9715)] to use TCP
#9715.
Default setting is "Enable".

Click the [Enable] check box for the
[Authentication] setting when authentication
is required.
Default setting is "Enable".

When the authentication setting is enabled, the following settings are required.

6HFXULW\6HWWLQJV

Network Control

Authentication
Password

Re-enter
Authentication
Password

Enter the desired authentication password.

&RQ¿UPWKLVVHWWLQJZLOOEHWKHVDPHIRU

[Network Control Port1 (Port: 23)] and
[Network Control Port2 (Port: 9715)].

Default setting is blank.

13

QM00112-1