Maxell MC-CW301 User Manual

Download

LCD Projector

MC-CW301/MC-CX301

User's Manual (detailed) Operating Guide

Thank you for purchasing this projector.

WARNING

product. Be sure to read “Safety Guide” rst. After reading them, store them in a safe place for future reference.

►Before using this product, please read all manuals for this

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING

CAUTION

NOTICE This entry notices of fear of causing trouble.

NOTE

• The illustrations in this manual are for illustrative purposes. They may differ slightly from your projector.

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

• The information in this manual is subject to change without notice.

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

Please refer to the pages written following this symbol.



QM00611-1

Contents



Introduction ...............3

Features ...................... 3

Checking the contents of package

Fastening the lens cover. . . . . . . . . ...4

Part names ....................4

Setting up .................8

Arrangement ...................8

Connecting with your devices Connecting to a power supply

.....10

.....16

Using the security bar and slot ....16

Remote control ............17

Installing the batteries ...........17

About the remote control signal ...18 Changing the frequency of remote control signal Using as a simple PC mouse & keyboard

. . 18

. . 19

Power on/off ..............20

Operating ................22

Adjusting the volume ............22

Temporarily muting the screen and

audio output ..................22

Selecting an input signal .........23

Selecting an aspect ratio .........23

Adjusting the projector's elevator . . 24 Adjusting the zoom and the focus . 24 Using the automatic adjustment feature

...25

Using the TEMPLATE feature .....26

Other buttons .................26

Adjusting the position ........... 27

Correcting the keystone distortions

Using the magnify feature ........28

Temporarily freezing the screen ...29

Using the menu function ........30

EASY MENU. . . . . . . . . . . . . . . 32

Aspect, mode, Filter time, Language, Advanced menu, Exit

D-zoom,

Eco mode, Installation, Reset,

Keystone,

Picture

PICTURE menu ............34

Brightness, Contrast, Hdcr, Accentualizer, Gamma, Color temp, Color, Tint, Sharpness, Active iris, My memory

IMAGE menu ..............37

Aspect, Over scan, V position, H position, H phase, H size, Auto adjust execute

INPUT menu ..............40

...3

SETUP menu ..............44

AUDIO menu ..............50

SCREEN menu .............52

OPTION menu .............58

NETWORK menu ...........72

SECURITY menu ...........73

Presentation tools .........78

. . 27

Maintenance ..............96

Troubleshooting ..........102

Specications ............113



Progressive, Video nr, Color space, Video format, Hdmi format, Hdmi range, Computer in, Frame lock, Resolution

D-zoom, D-shift, Picture position / Pict.posit. h,

Keystone,LAMP&FILTER,Image

Optimizer,

Volume, Speaker, Audio source, Mic Level,Mic volume

Language, Menu position, Blank, Auto Blank, Start up,

yScreen Lock

Template, C.c.

Auto search, Direct power on, Auto power off, My button, Schedule, Service

Security password change,

yScreen

My text password, My text display, My text writing, Cloning lock

Installation

password, Pin lock,

PC-LESS Presentation

USB Display (Windows computer) USB Display (Mac computer)

, Standby mode

, Message, Source name,

yScreen

...........78

... 88

.......92

Replacing the lamp .............96

Cleaning and replacing the air lter . . 98

Installing or replacing the internal

clock battery ......................

100

Other care ...................101

Related messages ............102

Regarding the indicator lamps ...104

Resetting all settings ...........107

Phenomena that may be easy to

be mistaken for machine defects

. . 107

QM00611-1

Introduction

Features

The projector provides you with the broad use by the following features.

ü The unique optics system produces a large projected image in a short

distance, which provides you with various ways of use.

ü This projector has a variety of I/O ports that supposedly cover for any

business scene.

ü The HDMI port can support various image equipment which have digital

interface to get clearer pictures on a screen.

ü Has an HDCR and an ACCENTUALIZER features which are original image

stabilizer for a clearer image.

ü This projector can be controlled and monitored via LAN connection.

Furthermore, you can use the designated USB wireless adapter (optional) to establish wireless LAN connection.

ü The built-in 16W speaker can deliver sufcient sound volume in a large

space like a classroom without external speakers.

ü This projector's network supports the PJLink™ standard.PJLink™ is a unied

standard for operating and controlling data projectors.For specications of

PJLink™, see the web site of the PJLink™. ü Equipped with IMAGE OPTIMIZER which is original function to maintain visibility by automatic image correction in accordance with lamp deterioration.

Checking the contents of package

Please see the Contents of package section in the User’s Manual (concise) which is a book. Your projector should come with the items shown there. Require of your dealer immediately if any items are missing.

NOTE

to use the original packing materials when moving the projector. Use special caution for the lens.

• Keep the original packing materials, for future reshipment. Be sure

QM00611-1

Introduction

Fastening the lens cover

To avoid losing the cover, please fasten the lens cover to the projector using the included strap.

Fasten the strap to the strap hole as shown

in the gure for step 1. Please note that the knot on the strap is used to fasten it to the lens cover in step 2.

Put the strap end into the slit of the lens

cover with the knot on the side of the lens. Make sure that the strap is inserted to the end of the slit.

Insert the upper tab (1 part) of the lens cover

between the upper case and lens as shown in the gure for step 3. Then, t the right/left tabs (2 parts) to attach the lens cover.

Strap hole

Lens cover

Strap

Upper caseLens

Strap slit

CAUTION

lens cover in front of the lens when the projector is mounted upside down such as when mounted on the ceiling. Otherwise, the lens cover may block the light from the projector or hit the lens, which may cause damage to it. When mounting the projector upside down, hang the lens cover on the side of the projector or place it on the projector. For instance, let the strap put through the concave portion around the security bar to hang the lens cover (refer to the gure). ►Be careful not to damage the lens while handling the lens cover.

►Do not hang the

Upper tab

Right/Left tabs

QM00611-1

Introduction

Part names

Projector

(1) Control panel (6) (2) Lamp cover (96)

The lamp unit is inside. (3) Remote sensor (18) (4) Lens (101) (5) AC (AC inlet) (16) (6) Ports (6) (7) Exhaust vent (8) Speaker (13, 22, 50) (9) Elevator feet (x 2) (24) (10) Spacer (24) (11) Security slot (16) (12) Security bar (16) (13) Strap hole (4) (14) FOCUS ring (25) (15) Filter cover (98)

The air lter and intake

vent are inside. (16) Intake vents (17) Battery Cover (100)

(3)

(4)

(2)

HOT!

(1)

(5)

(6)

(7)

HOT!

(14)

(16)

(15)

WARNING

►HOT! : Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot. ►Do not look into the lens or vent while the lamp is on, since the projection ray may cause a trouble on your eyes. ►Do not use the security bar and slot to prevent the projector from falling down, since it is not designed for it. ►Keep any object away from concentrated projection light beam. Blocking the beam by something causes high temperature and could result in re or smoke.

CAUTION

►Maintain normal ventilation to prevent the projector from heating up. Do not cover, block or plug up the vents. Do not place anything that can stick or be sucked to the vents, around the intake vents. Clean the air lter periodically.

QM00611-1

Introduction

Part names (continued)

(5)

Control panel

(4)

(1) STANDBY/ON button (20) (2) INPUT button (23) (3) POWER indicator (20, 104) (4) TEMP indicator (104) (5) LAMP indicator (104) Buttons ◄/►/▲/▼ (6) MENU / Cursor button (30)

(1)

(2)

(6)

(3)

when no menu is displayed (30), or Cursor ▲/▼ buttons when a menu is displayed (30). The ◄/►/▲/▼ buttons on the projector work only as the cursor buttons while the template is displayed (56).

Ports (

10 ~ 15)

(1) USB TYPE A port (x2) (2) LAN port (3) USB TYPE B port (4) HDMI port (x2) (5) MIC port (6) AUDIO IN1 port (7) AUDIO IN2(L,R) ports (8) AUDIO OUT port

(1)

(2)

(3)

(9) COMPUTER IN1 port (10) COMPUTER IN2 / MONITOR OUT port (11) VIDEO IN port (12) CONTROL port

(5)

(6)

(12)(11)

(8)

(9)

(10)

(4)

(7)

QM00611-1

Introduction

Part names (continued)

Remote control

(1) INPUT button (23) (2) IWB button * (3) CALIBRATION button * (4) STANDBY/ON button (20) (5) ASPECT button (23) (6) AUTO button (25) (7) ACCENTUALIZER button (26) (8) HDCR button (26) (9) D-ZOOM - button (24) (10) D-ZOOM + button (24) (11) PAGE UP button (19) (12) MAGNIFY - ON button (28) (13) MY BUTTON - 1 button (60) (14) VOLUME + button (22) (15) PAGE DOWN button (19) (16) MAGNIFY - OFF button (28) (17) MY BUTTON - 2 button (60) (18) VOLUME - button (22) (19) KEYSTONE button (27) (20) TEMPLATE button (26) (21) FREEZE button (29) (22) AV MUTE button (22) (23) ESC button (30) (24) MENU button (30, 31) (25) ENTER button (30, 31) (26) POSITION button (27, 31) (27) RESET button (30) (28) ▲/▼/◄/► cursor buttons (30) (29) Battery cover (17)

(2) (1) (6) (5)

ASPECT

(11) (12) (15)

KEYSTONE

(16) (19) (20) (23) (28)

POSITION

(26)

the remote control

IWB

INPUT

CALIBRATION

AUTO

ACCENTUALIZER

D-ZOOM

PAGE

MAGNIFY

MYBUTTON

DOWNONOFF

FREEZE

TEMPLATE

ESC MENU

ENTER

Back of

HDCR

VOLUME

AV MUTE

RESET

(3) (4) (7) (8) (9)

(10)

＋

(14)

ー

(13) (18) (17) (22) (21) (24) (25) (27)

(29)

• Any button marked with “*” is not supported on this projector (103).NOTE

QM00611-1

Setting up

Install the projector according to the environment and manner the projector will be used in.

Arrangement

Refer to table T-1 or T-2 and gures F-1 and F-2 at the end of User’s Manual (concise) to determine the screen size and projection distance.

The values shown in the table are calculated for a full size screen. V Screen size (vertical) H Screen size (horizontal) a Projection distance (±8%) b1 , b2 Screen height (±8%)

• For the case of installation in special conditions such as on the wall or ceiling, the

specied mounting accessories and service may be required. Tabletop use must be setup with the designated optional accessories. Before installing the projector, consult your dealer about your installation.

The screen position may shift after installation if the projector is mounted on locations

•

such as the wall or ceiling, due to the exibility of the plastic projector body. If readjustment is necessary, consult with your dealer or service personnel.

• The projected image position and/or focus may change during warm-up (approx. 30

minutes after the lamp is turned on) or when the ambient conditions change. Readjust the image position and/or focus as necessary.

• Since the projector features an ultra short throw, be aware that it is required to select a

screen carefully to have better performance.

- A soft screen such as a pull-down screen may cause serious distortion of a projected image. A hard screen such as a board screen is recommended for use with this projector.

- A high-gain screen such as a bead screen that has narrow viewing angle is not suitable for this projector. A low-gain screen (around 1.0) such as a matte screen that has wide viewing angle is recommended for use with this projector.

A screen with a weave pattern may cause moiré on the projected image, which is not a failure of the projector. A screen that has less moiré effects is recommended for use with this projector.

►

WARNING

Place the projector in a stable horizontal position. If the projector falls or is knocked over, it could cause injury and/or damage to the projector. Using a damaged projector could then result in re and/or electric shock.

• Do not place the projector on an unstable, slanted or vibrational surface such

as a wobbly or inclined stand.

• Do not place the projector on its side or front position. To place the projector

on its rear position for the table top use, it is required to use the designated optional parts. Consult with your dealer.

• Consult with your dealer before a special installation such as on the wall or

ceiling.

(continued on next page)

QM00611-1

Setting up

Arrangement (continued)

WARNING

►Place the projector in a cool place, and ensure that there is sufcient ventilation. The high temperature of the projector could cause re, burns and/or malfunction of the projector.

• Do not stop-up, block or otherwise cover the projector's vents.

• Keep a space of 30 cm or more between the sides of the projector and other

objects such as walls.

•

Do not place or attach anything that would block the projection window or vent holes.

• Do not place the projector on metallic thing or anything weak in heat.

• Do not place the projector on carpet, cushions or bedding.

• Do not place the projector in direct sunlight or near hot objects such as heaters.

Do not place the projector where the air from an air conditioner or similar unit will blow on it directly.

•

Do not place anything near the projection window or vents, or on top of the

projector.

•

Do not place anything that may be sucked into or stick to the vents on the

bottom of the projector. This projector has some intake vents also on the bottom. ►Do not place the projector anyplace where it may get wet. Getting the projector wet or inserting liquid into the projector could cause re, electric shock and/or malfunction of the projector.

• Do not place the projector in a bathroom or the outdoors.

• Do not place anything containing liquid near the projector.

•

Do not place the projector where any oils, such as cooking or machine oil, are used. Oil may harm the product, resulting in malfunction, or falling from the mounted position. Do not use adhesive such as threadlocker, lubricant and so on.

►

Use only the mounting accessories the manufacturer specied, and leave installing

and removing the projector with the mounting accessories to the service personnel.

• Read and keep the user’s manual of the mounting accessories used.

CAUTION

►Avoid placing the projector in smoky, humid or dusty place. Placing the projector in such places could cause re, electric shock and/or malfunction of the projector.

• Do not place the projector near humidiers, smoking spaces or a kitchen. Also do not use an ultrasonic humidier near the projector. Otherwise chlorine and minerals contained in tap water are atomized and could be deposited in the projector causing image degradation or other problems. ►

Position the projector to prevent light from directly hitting the projector's remote sensor. ►Do not place the product in a place where radio interference may be caused. ►Do not place this product in a magnetic eld. ►

If the projector is used at an altitude of about 1600 m or higher, set ALTITUDE of the SERVICE item in the OPTION menu to HIGH

(64). Otherwise, set it to NORMAL. If the projector is used with a wrong setting, it may cause damage to the projector itself or the parts inside.

(continued on next page)

QM00611-1

Arrangement (continued)

Setting up

NOTE

• The projector may make a rattling sound when tilted, moved or shaken, since a ap to control the air ow inside of the projector has moved. Be aware that this is not a failure or malfunction.

• The incoming light to the screen from the projector has a large angle. While the white image is on the screen, you may see it with colors, but this is because of the type of the screen used or the angles viewed, and it is not a malfunction.

• When the ambient temperature is around 35 to 40°C, the brightness of lamp is reduced automatically.

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to conrm that the device is suitable for connecting with this projector and prepare the required accessories, such as a cable in accord with the signal of the device. Consult your dealer when the required accessory did not come with the product or the accessory is damaged. After making sure that the device and projector are turned off, connect them following the instructions below.

►

WARNING

a re or damage to the device and the projector.

- Use only the accessories specified or recommended by the projector’s manufacturer. Consult your dealer when the required accessory did not come with the product or the accessory is damaged. It may be regulated under some standard.

- For a cable with a core at only one end, connect the end with the core to the projector. That may be required by EMI regulations.

- Neither disassemble nor modify the projector and the accessories.

- Do not use the damaged accessory. Be careful not to damage the accessories.

Route a cable so that it is neither stepped on nor pinched out.

CAUTION

in operation, unless that is directed in the manual of the device. Otherwise it may cause malfunction in the device or projector. ►Be careful not to mistakenly connect a connector to a wrong port. Otherwise it may cause malfunction in the device or projector.

- When connecting a connector to a port, make sure that the shape of the

connector ts the port.

- Tighten the screws to connect a connector equipped with screws to a port.

- Use the cables with straight plugs, not L-shaped ones, as the input ports of the

projector are recessed.

Use only the appropriate accessories. Otherwise it could cause

►Do not turn on or off the projector while connected to a device

(continued on next page)

QM00611-1

Setting up

Connecting with your devices (continued)

About Plug-and-Play capability

• Plug-and-Play is a system composed of a computer, its operating system and peripheral equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and-Play can be used by connecting this projector to a computer that is VESA DDC (display data channel) compatible.

- Take advantage of this feature by connecting a computer cable to the COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

Please use the standard drivers in your computer as this projector is a Plug-and-

Play monitor.

• When AUTO is selected for the COMPUTER IN1 or COMPUTER IN2 port in COMPUTER IN of the INPUT menu, that port will accept component video signals (

•

When the USB TYPE B port and the computer's type A USB port are connected,

42).

you can use the remote control as a simple mouse and keyboard of the computer. (19).

VCR/DVD/Blu-ray Disc

player

HDMI

Cr/Pr

Cb/Pb

COMPONENT

VIDEO

OUT

AUDIO

(continued on next page)

Computer

QM00611-1

USB

(A)

HDMI

DISPLAY

AUDIO

OUT

RS-232C

Connecting with your devices (continued)

Setting up

NOTE

• Before connecting the projector to a computer, consult the computer’s manual and check the compatibility of the signal level, the synchronization methods and the display resolution output to the projector.

- Some signal may need an adapter to input this projector.

- Some computers have multiple screen display modes that may include some

signals which are not supported by this projector.

- Although the projector can display signals with resolution up to UXGA

(1600X1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and the projector panel are identical.

• If you connect this projector and a notebook computer, you need output the

display to an external monitor, or output simultaneously to the internal display and an external monitor. Consult the computer's manual for the setting.

• Depending on the input signal, the automatic adjustment function of this

projector may take some time and not function correctly.

- Note that a composite sync signal or sync-on-green signal may confuse the

automatic adjustment function of this projector (42).

- If the automatic adjustment function does not work correctly, you may not see

the dialog to set the display resolution. In such a case, use an external display device. You may be able to see the dialog and set an appropriate display resolution.

(continued on next page)

QM00611-1

Setting up

RGB IN

Connecting with your devices (continued)

• If you insert a USB storage device, such as a USB memory, into the USB TYPE A port and select the port as the input source, you can view images stored in the

device (78).

• You can connect a dynamic microphone to the MIC port with a 3.5 mm mini-plug. In that case, the built-in speaker outputs the sound from the microphone, even while the sound from the projector is output. You can input line level signal to the MIC port from equipment such as wireless microphone. In the normal mode, the volume of the microphone can be adjusted separately from the volume of the projector using the menu. (51)

In the standby mode, the volume of the microphone is adjustable with the VOLUME +/- buttons on the remote control, in synchronization with the volume of the projector. (22) Even when the sound of projector is set to mute mode by the AUDIO SOURCE function (50), the volume of the microphone is adjustable. In both modes (standby or normal), the AV MUTE button on the remote control works on the sounds of the microphone and the projector. (22)

Microphone

system

NOTE

Speakers

(with an amplier)

• If a loud feedback noise is produced from the speaker, move the

microphone away from the speaker.

• This projector doesn't support plug-in power for the microphone.

(continued on next page)

Monitor

QM00611-1

Setting up

Connecting with your devices (continued)

To use network functions of the projector, connect the LAN port with the computer's LAN port, or with an access point that is connected to the computer with wireless LAN, using a LAN cable. To use NETWORK BRIDGE function, also connect the CONTROL port and an RS-232C port of the external device to communicate as a network terminal. See the User's Manual - Network Guide for details of the network functions.

External

Device

RS-232C

USB

wireless

adapter

(optional)

USB storage

device

Access point Computer

LAN

USB TYPE A

RS-232C

CAUTION

►Before connecting the projector to a network system be sure to obtain the consent of the administrator of the network. ►

Do not connect the LAN port to any network that might have the excessive voltage.

►The designated USB wireless adapter that is sold as an option is required to use the wireless network function of this projector. ►Before removing the USB storage device from the port of the projector, be sure to use the REMOVE USB function on the thumbnail screen to secure your data (81). ►Do not use any extension cable or device when connecting the adapter to the projector. Before you insert or pull out the USB wireless adapter from the projector, turn off the power of the projector and pull out the power cord’s plug from the outlet. Do not touch the USB wireless adapter while the projector is receiving AC power. ►To connect both the LAN cable and USB device to the projector, use a LAN cable that is at on the side where the plug’s wire is visible. Otherwise, both of them cannot be connected correctly, or the wire may break (malfunction).

(continued on next page)

QM00611-1

Setting up

Connecting with your devices (continued)

NOTE

• If an oversized USB storage device blocks the LAN port, use a USB

extension cable to connect the USB storage device.

• The HDMI port of this model is compatible with HDCP (High-bandwidth Digital Content Protection) and therefore capable of displaying a video signal from HDCP compatible DVD players or the like.

- The HDMI supports the following signals. Video signal : 480i@60, 480p@60, 576i@50, 576p@50, 720p@50/60, 1080i@50/60, 1080p@50/60 Audio signal : Format Linear PCM Sampling frequency 48kHz / 44.1kHz / 32kHz

- This projector can be connected with another equipment that has HDMI

connector, but with some equipment the projector may not work properly, something like no video.

- Be sure to use an HDMITM cable that has the HDMITM logo.

- Use a Category 2-certied HDMITM cable to input 1080p@50/60 signal to the projector.

- When the projector is connected with a device having DVI connector, use a DVI to HDMITM cable to connect with the HDMI input.

• Up to one USB wireless adapter (optional) can be connected to a projector.

QM00611-1

Connecting to a power supply

Put the connector of the power cord into the

AC (AC inlet) of the projector. Firmly plug the power cord’s plug into the

outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange.

Please remember that when the DIRECT POWER ON function activated ( power supply make the projector turn on.

58), the connection of the

Setting up

Power cord

WARNING

incorrect or faulty connections may result in re and/or electrical shock.

• Do not touch the power cord with a wet hand.

• Only use the power cord that came with the projector. If it is damaged, consult your dealer to get a new one. Never modify the power cord.

• Only plug the power cord into an outlet whose voltage is matched to the power cord. The power outlet should be close to the projector and easily accessible. Remove the power cord for complete separation.

• Do not distribute the power supply to multiple devices. Doing so may overload the outlet and connectors, loosen the connection, or result in re, electric shock or other accidents.

• Do not press the main body of projector on the power cord.

• Connect the ground terminal for the AC inlet of this unit to the ground terminal of the building using an appropriate power cord (bundled).

►Please use extra caution when connecting the power cord, as

Using the security bar and slot

A commercial anti-theft chain or wire up to 10 mm in diameter can be attached to the security bar on the projector. Also this product has the security slot for the Kensington lock. For details, see the manual of the security tool.

WARNING

from falling down, since it is not designed for it.

CAUTION

It may become too hot.

►Do not use the security bar and slot to prevent the projector

►Do not place anti-theft chain or wire near the exhaust vents.

Anti-theft chain or wire

Security slot

Security bar

NOTE

measures. It is intended to be used as supplemental theft prevention measure.

• The security bar and slot is not comprehensive theft prevention

QM00611-1

Remote control

Installing the batteries

Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.

Remove the battery cover.

Align and insert the two AA batteries (Use the appropriate

AA carbon-zinc or alkaline batteries (non-rechargeable) in accordance with laws and regulations.) according to their plus and minus terminals as indicated in the remote control.

Put the battery cover back to the former state.

WARNING

directed. Improper use may result in battery explosion, cracking or leakage, which could result in re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specied. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.

• If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

►Always handle the batteries with care and use them only as

QM00611-1

Remote control

About the remote control signal

Remote

sensor

The remote control works with the projector’s remote sensor. This projector has a remote sensor on the front. The sensor senses the signal within the following range when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor)

30º

Approx.

3 m

within 3 meters about.

NOTE

•

The remote control signal reected in the screen or the like may be available.

If it is difcult to send the signal to the sensor directly, attempt to make the signal reect.

• The remote control uses infrared light to send signals to the projector (Class 1 LED), so be sure to use the remote control in an area free from obstacles that could block the remote control’s signal to the projector.

•

The remote control may not work correctly if strong light (such as direct sun

light) or light from an extremely close range (such as from an inverter uorescent lamp) shines on the remote sensor of the projector. Adjust the position of projector avoiding those lights.

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control does not function properly, attempt to change the signal frequency. In order to set the Mode, please keep pressing the combination of two buttons listed below simultaneously for about 3 seconds.

(1) Set to Mode 1:NORMAL... VOLUME - and RESET buttons (2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

PAGE

MAGNIFY

MYBUTTON

DOWNONOFF

FREEZE

KEYSTONE

TEMPLATE

ESC MENU

ENTER

POSITION

HDCR

D-ZOOM

VOLUME

＋

ー

AV MUTE

RESET

(1)(2)

Please remember that the REMOTE FREQ. in the SERVICE item of the OPTION menu

(66)

of the projector to be controlled should be set to the same mode as the remote control.

QM00611-1

Remote control

Using as a simple PC mouse & keyboard

The accessory remote control works as a simple mouse and keyboard of the computer, when the projector’s USB TYPE B port and the computer’s type A USB port are connected.

(1) PAGE UP key: Press PAGE UP button. (2) PAGE DOWN key: Press PAGE DOWN button. (3) Mouse left button: Press ENTER button. (4) Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►. (5) ESC key: Press ESC button. (6) Mouse right button: Press RESET button.

NOTICE

►Improper use of the simple mouse & keyboard function could damage your equipment. While using this function, please connect this product only to a computer. Be sure to check your computer’s manuals before connecting this product to the computer.

USB TYPE B

port

(5)

(3)

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

PAGE

MAGNIFY

MYBUTTON

DOWNONOFF

FREEZE

KEYSTONE

TEMPLATE

ESC MENU

ENTER

POSITION

(1)

HDCR

D-ZOOM

VOLUME

＋

(2)

ー

AV MUTE

(4)

RESET

(6)

NOTE

• When the simple mouse & keyboard function of this product does not work

correctly, please check the following.

• When a USB cable connects this projector with a computer having a built-in pointing device (e.g. track ball) like a laptop PC, open BIOS setup menu, then select the external mouse and disable the built-in pointing device, because the built-in pointing device may have priority to this function.

•

Windows XP SP3 or higher is required for this function. And also this function may not work depending on the computer’s congurations and mouse drivers. This function can work with the computer which can operate general USB mouse or keyboard.

• You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

•

This function is activated only when the projector is working properly. This function is not available in any of the following cases:

- While the lamp is warming up. (The POWER indicator blinks in green.)

When USB TYPE A port is selected.

- While displaying BLANK

(22)

, TEMPLATE

(56)

or MY IMAGE screen.

- When any menu is displayed on the screen.

While using the cursor buttons to operate the sound or screen functions such as adjusting the sound volume, correcting the keystone, correcting the picture position and magnifying the screen.

QM00611-1

Power on/off

CALIBRATION

ASPECT

ACCENTUALIZER

HDCR

AV MUTE

POSITION

ESC MENU

RESET

IWB

AUTO

PAGE

DOWNONOFF

FREEZE

ENTER

D-ZOOM

＋

ー

VOLUME

MAGNIFY

MYBUTTON

INPUT

KEYSTONE

TEMPLATE

Power on/off

Turning on the power

Make sure that the power cord is rmly

and correctly connected to the projector and the outlet. Make sure that the POWER indicator is

steady orange (104).Then, remove the lens cover.

Press STANDBY/ON button on the

projector or the remote control. The projection lamp lights up, and the POWER indicator begins to blink green. When the power is completely on, the indicator will stop blinking and light in steady green (104).

To display the picture, select an input signal according to the section Selecting an input signal (

The INITIAL SETTING Menu will be displayed by factory default upon startup. Once the INITIAL SETTING Menu is set, it will not appear until FACTORY RESET

71) is executed. If you wish to change the settings, refer to the LANGUAGE

( (52) and ALTITUDE (64) menu.

23).

STANDBY/ON button

POWER indicator

(1) LANGUAGE: Use the ▲/▼/◄/►

buttons to select the desired language and press the ENTER button of the remote control or the INPUT button of the projector to execute.

(2) ALTITUDE: Use the ▲/▼ buttons to

select NORMAL for altitude below 1600 m (5250 feet), otherwise select HIGH and press the ENTER button of the remote control or the INPUT button of the projector to execute.

(continued on next page)

QM00611-1

Power on/off

Turning off the power

Press the STANDBY/ON button on the projector or the remote control.

The message “Power off?” will appear on the screen for about 5 seconds.

Press the STANDBY/ON button again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete (104).

Do not turn the projector on for about 10 minutes or more after turning it off. Also, do not turn the projector off shortly after turning it on. Such operations might cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.

WARNING

Do not look into the lens of the projector or look inside of the projector through any of the projector’s openings, since the projection ray may cause a trouble on your eyes. ►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot. ►Remove the power cord for complete separation. The power outlet should be close to the projector and easily accessible.

NOTE

• Turn the power on/off in right order. Please power on the

►A strong light is emitted when the projector’s power is on.

projector prior to the connected devices.

•

This projector has the function that can make the projector automatically turn on/off. Please refer to the DIRECT POWER ON (58)

and AUTO POWER OFF

(59)

items of the OPTION menu.

QM00611-1

Operating

Adjusting the volume

Use the VOLUME +/VOLUME - buttons to adjust the volume.

A dialog will appear on the screen to aid you in adjusting the volume. If you do not do anything, the dialog will automatically disappear after about ten seconds.

● When

is selected for current picture input port, the volume adjustment is

VOLUME +/- button

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

PAGE

MAGNIFY

MYBUTTON

DOWNONOFF

disabled. Please see AUDIO SOURCE item of AUDIO menu (50).

● Even if the projector is in the standby mode, the volume is adjustable when both of the following conditions are true:

- An option other than is selected for STANDBY in the AUDIO SOURCE item of the AUDIO menu (50).

NORMAL is selected in the STANDBY MODE item of the SETUP menu

● In the standby mode, the volume of the microphone is adjustable with the VOLUME +/- buttons on the remote control, in synchronization with the volume of the projector (11).

Temporarily turning off the screen and audio output

AV MUTE button

IWB

INPUT

Press AV MUTE button on the remote control.

The BLANK screen will be displayed instead of the screen of input signals and the sound from the AUDIO OUT port will be muted. Please refer to the BLANK item in SCREEN menu about the BLANK screen (52). To exit from the AV MUTE mode and restore the screen and audio, press AV MUTE button again.

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

PAGE

MAGNIFY

MYBUTTON

DOWNONOFF

FREEZE

KEYSTONE

TEMPLATE

ESC MENU

HDCR

D-ZOOM

VOLUME

＋

ー

(49).

HDCR

D-ZOOM

VOLUME

＋

ー

AV MUTE

NOTE

• The projector automatically exits from the AV MUTE mode

when some control buttons are pressed.

•

The audio is output from the external audio system connected to

the AUDIO OUT port.

WARNING

is on, use the AV MUTE function above . Taking any other action may cause the damage on the projector. Blocking the beam by something causes high temperature and could result in re or smoke.

►If you wish to have a blank screen while the projector's lamp

QM00611-1

Selecting an input signal

Press INPUT button on the projector.

Each time you press the button, the projector switches its input port from the current port as below.

INPUT button

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

HDCR

D-ZOOM

PAGE

VOLUME

MAGNIFY

MYBUTTON

Operating

INPUT button

＋

COMPUTER IN1  COMPUTER IN2

VIDEO IN LAN

HDMI

2 USB TYPE A

●

While ON is selected for AUTO SEARCH item in OPTION menu (58), the projector

HDMI 1  USB TYPE B

will keep checking the ports in above order repeatedly till an input signal is detected.

●

It may take several seconds to project the images from the USB TYPE B port.

Selecting an aspect ratio

Press ASPECT button on the remote control.

Each time you press the button, the projector switches the mode for aspect ratio in turn.

 For a computer signal

NORMAL  4:3  16:9  16:10  NATIVE

 For an HDMI

signal

NORMAL  4:3  16:9  16:10  14:9  NATIVE

 For a video signal or component video signal

4:3  16:9  16:10  14:9  NATIVE

 For an input signal from the LAN, USB TYPE A or USB TYPE B port, or

if there is no signal

MC-CX301: 4:3 (xed) MC-CW301: 16:10 (xed)

ASPECT button

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

PAGE

MAGNIFY

DOWNONOFF

KEYSTONE

TEMPLATE

MYBUTTON

FREEZE

D-ZOOM

HDCR

VOLUME

AV MUTE

＋

ー

● ASPECT button does not work when no proper signal is inputted.

● NORMAL mode keeps the original aspect ratio setting.

● The on-screen menu might be displayed outside of the image display area

depending on the adjustment value of the ASPECT, D-ZOOM, KEYSTONE. Changing the values of ASPECT, D-ZOOM, KEYSTONE may x the symptom.

QM00611-1

Operating

Adjusting the projector's elevator

The projector has Front foot for inclinations and Rear foot for horizontals. Spacers on the each elevator foot are installed at the time of shipment, and projector is in a condition to be able to just project. If necessary, detach the spacer, and the elevator feet can be manually twisted to make more precise adjustments.

0~2°

Front foot

Rear foot

Front foot

-1~1°

WARNING

Spacer

►Keep the spacers away from children and pets. Be careful not

Rear foot

Spacer

to let them swallow the spacers. If swallowed, consult a physician immediately for emergency treatment.

NOTE

• The Front foot can be adjusted within 0~2°, while the Rear foot can

be adjusted within -1~1°

•

After the foot is adjusted, it is possible to return it to the state of the shipment with a spacer. If change the setting place of the projector, it will recommend keep and reuse the spacers.

Adjusting the zoom and the focus

Press the D-ZOOM + or D-ZOOM - button on the remote control to display D-ZOOM dialog on screen. Use the D-ZOOM + and D-ZOOM - buttons to adjust the picture size. To nish the operation, do not touch these buttons for about ten seconds until the dialog is disappeared.

● If you want to expand a part of the image, use the magnify function (28).

D-ZOOM - button

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

HDCR

D-ZOOM

PAGE

KEYSTONE

ESC MENU

DOWNONOFF

MAGNIFY

TEMPLATE

MYBUTTON

FREEZE

VOLUME

AV MUTE

＋

ー

(continued on next page)

D-ZOOM + button

QM00611-1

Operating

Use the focus ring to focus the picture.

FOCUS ring

Using the automatic adjustment feature

Press AUTO button on the remote control.

Pressing this button performs the following.

 For a computer signal

The vertical position, the horizontal position and the horizontal phase will be automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.

 For a video signal

The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO is selected for

41).

the VIDEO FORMAT item in the INPUT menu (

The vertical position and

horizontal position will be automatically set to the default.

 For a component video signal

The vertical position and horizontal position will be automatically set to the default. The horizontal phase will be automatically adjusted.

● The automatic adjustment operation requires approx. 10 seconds. Also please note that it may not function correctly with some input.

● When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

● When this function is performed for a computer signal, a black frame may be displayed on the edge of the screen, depending on the PC model.

The items adjusted by this function may vary when the FINE or DISABLE is selected

● for the AUTO ADJUST item of the SERVICE item in the OPTION menu (

AUTO button

IWB

INPUT

ASPECT

AUTO

PAGE

MAGNIFY

DOWNONOFF

KEYSTONE

TEMPLATE

64).

CALIBRATION

ACCENTUALIZER

D-ZOOM

MYBUTTON

FREEZE

AV MUTE

HDCR

VOLUME

＋

ー

QM00611-1

Operating

Using the TEMPLATE feature

Press TEMPLATE button on the remote control.

Each time you press the button, the projector switches the mode for TEMPLATE in turn.

TEST PATTERN  DOT-LINE1  DOT-LINE2  DOT-LINE3

MAP2



MAP1  CIRCLE2  CIRCLE1  DOT-LINE4

TEMPLATE button

● TEMPLATE button does not work when no proper signal is inputted.

Other buttons

HDCR: Displays the HDCR menu (34). ACCENTUALIZER: Displays the ACCENTUALIZER menu (34).

INPUT

ASPECT

PAGE

ACCENTUALIZER

button

KEYSTONE

DOWNONOFF

IWB

AUTO

MAGNIFY

TEMPLATE

INPUT

ASPECT

PAGE

DOWNONOFF

KEYSTONE

CALIBRATION

ACCENTUALIZER

MYBUTTON

FREEZE

D-ZOOM

IWB

AUTO

MAGNIFY

TEMPLATE

VOLUME

AV MUTE

ACCENTUALIZER

HDCR

CALIBRATION

MYBUTTON

FREEZE

＋

ー

D-ZOOM

HDCR

VOLUME

AV MUTE

＋

ー

HDCR button

QM00611-1

CALIBRATION

ASPECT

ACCENTUALIZER

HDCR

AV MUTE

IWB

AUTO

PAGE

DOWNONOFF

FREEZE

D-ZOOM

＋

ー

VOLUME

MAGNIFY

MYBUTTON

INPUT

KEYSTONE

TEMPLATE

Operating

CALIBRATION

IWB

INPUT

Adjusting the position

Press the POSITION button on the remote control while no menu

is on screen, to display the D-SHIFT

Use the ▲, ▼, ◄ and ► buttons to adjust the picture position.

Press the POSITION button again to nish this operation.

(44)

dialog on screen.

● This is a function to shift the position of the shrunken picture by the D-ZOOM function.

● When an OSD (On Screen Display) menu is displayed, this operation moves the position of the OSD menu, but not the position of the picture

(31)

● The D-SHIFT adjustment values are not valid when the D-ZOOM is set to 256 (full screen). (MC-CX301)

● The D-SHIFT adjustment values are not valid when the D-ZOOM is set to 320 (full screen). (MC-CW301)

ESC MENU

ENTER

POSITION

POSITION button

RESET

(44)

Correcting the keystone distortions

Press the KEYSTONE button on the remote control.

A dialog will appear on the screen to aid you in correcting the

KEYSTONE button

distortion. Use the ◄/► cursor buttons for adjustment.

To close the dialog and complete this operation, press the KEYSTONE button again. Even if you do not do anything, the dialog will automatically disappear after about ten seconds.

● The adjustable range of this function varies for each input signal. For some input, this function may not work well.

● When the projector is inclined to near ±5 degrees or over, this function may not work well.

● The OSD menu might be displayed outside of the image display area depending on the adjustment value of the ASPECT, D-ZOOM and the values of ASPECT, D-ZOOM and

KEYSTONE may x the symptom.

KEYSTONE. Changing

ASPECT

AUTO

ACCENTUALIZER

PAGE

MAGNIFY

MYBUTTON

DOWNONOFF

FREEZE

KEYSTONE

TEMPLATE

ESC MENU

D-ZOOM

HDCR

VOLUME

AV MUTE

＋

ー

QM00611-1

Operating

Using the magnify feature

Press the MAGNIFY ON button on the remote control.

The picture will be magnied, and the MAGNIFY dialog will appear on the screen. When the MAGNIFY ON button is pressed for the rst time after the projector is turned on, the picture will be zoomed by 1.5 times. On the dialog, triangle marks to show each direction will be displayed.

The display magnication of the projector switches in order

with every press of the MAGNIFY ON button.

 For computer signals, HDMI

(RGB) signals, input signals from the

MAGNIFY ON/OFF button

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

D-ZOOM

PAGE

MAGNIFY

MYBUTTON

DOWNONOFF

LAN, USB TYPE A or USB TYPE B port

1.5 times  2 times  3 times  4 times  1 time



For video signals, component video signals or HDMITM (Component)

signals

1.5 times  2 times  1 time

While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor

buttons to shift the magnifying area.

Press the MAGNIFY OFF button on the remote control to exit magnication.

● The MAGNIFY dialog will automatically disappear in several seconds with no

operation. The dialog will appear again if the MAGNIFY ON button is pressed when the dialog has automatically disappeared.

● The magnication is automatically disabled when the displaying signal or its

display condition is changed.

● While the magnication is active, the keystone distortion condition may vary.

It will be restored when the magnication is disabled.

● Some horizontal stripes might be visible on the image while magnication is

active.

● This function is not available in the following cases:

- A sync signal in the range not supported is input.

- There is no input signal.

VOLUME

HDCR

＋

ー

QM00611-1

Operating

Temporarily freezing the screen

Press the FREEZE button on the remote control.

The “FREEZE” indication will appear on the screen (however, the indication will not appear when the OFF is selected for the MESSAGE item in the SCREEN menu (54)), and the projector will go into the FREEZE mode, which the picture is frozen. To exit the FREEZE mode and restore the screen to normal, press the FREEZE button again.

● The projector automatically exits from the FREEZE mode when some control

buttons are pressed.

● If the projector continues projecting a still image for a long time, the LCD

panel might possibly be burned in. Do not leave the projector in the FREEZE mode for too long.

● Images might appear degraded when this function is operated, but it is not a

malfunction.

FREEZE button

IWB

INPUT

CALIBRATION

ASPECT

AUTO

ACCENTUALIZER

PAGE

MAGNIFY

MYBUTTON

DOWNONOFF

FREEZE

KEYSTONE

TEMPLATE

HDCR

D-ZOOM

VOLUME

＋

ー

AV MUTE

QM00611-1

CALIBRATION

ASPECT

ACCENTUALIZER

HDCR

AV MUTE

IWB

AUTO

PAGE

DOWNONOFF

FREEZE

D-ZOOM

＋

ー

VOLUME

MAGNIFY

MYBUTTON

INPUT

KEYSTONE

TEMPLATE

Operating

Using the menu function

This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, SECURITY and EASY MENU. EASY MENU consists of functions often used, and the other menus are classied into each purpose and brought together as the ADVANCED MENU. Each of these menus is operated using the same methods. While the projector is displaying any menu, the MENU button on the projector works as the cursor buttons. The basic operations of these menus are as follows.

ESC button

MENU button

Cursor buttons

ESC MENU

ENTER

MENU button

POSITION

RESET

(Cursor buttons)

ENTER button

To start the MENU, press the MENU button. The MENU you last used (EASY

or ADVANCED) will appear. EASY MENU has priority to appear just after

RESET button

powered on.

In the EASY MENU

(1) Use the ▲/▼ cursor buttons to select an item to

operate. If you want to change it to the ADVANCED MENU, select the ADVANCED MENU.

(2) Use the ◄/► cursor buttons to operate the item.

In the ADVANCED MENU

(1) Use the ▲/▼ cursor buttons to select a menu.

If you want to change it to the EASY MENU, select the EASY MENU. The items in the menu appear on the right side.

(2) Press the ► cursor button or ENTER button to

move the cursor to the right side. Then use the ▲/▼ cursor buttons to select an item to operate and press the ► cursor button or ENTER button to progress. The operation menu or dialog of the selected item will appear.

(3) Use the buttons as instructed in the OSD to operate the item.

IWB

INPUT

ASPECT

AUTO

PAGE

MAGNIFY

DOWNONOFF

KEYSTONE

TEMPLATE

ESC MENU

POSITION

CALIBRATION

ACCENTUALIZER

HDCR

D-ZOOM

VOLUME

MYBUTTON

＋

ー

FREEZE

AV MUTE

ENTER

RESET

(continued on next page)

QM00611-1

Operating

Using the menu function (continued)

To close the MENU, press the MENU button again or select EXIT and press

the ◄ cursor button or ENTER button. Even if you do not do anything, the dialog will automatically disappear after about 30 seconds.

●

If you want to move the menu position, use the cursor buttons after pressing the

POSITION button.

● Some functions cannot be performed when a certain input port is selected, or when a certain input signal is displayed.

● When you want to reset the operation, press RESET button on the remote control during the operation. Note that some items (ex. LANGUAGE, VOLUME) cannot be reset.

● In the ADVANCED MENU, when you want to return to the previous display, press the ◄ cursor button or ESC button on the remote control.

Indication in OSD (On Screen Display)

The meanings of the general words on the OSD are as follows.

Indication Meaning

EXIT

RETURN Selecting this word returns the menu to the previous menu.

CANCEL or NO

OK or YES

Selecting this word nishes the OSD menu. It's the same as pressing the MENU button.

Selecting this word cancels the operation in the present menu and returns to the previous menu.

Selecting this word executes the prepared function or shifts the menu to the next menu.

QM00611-1

EASY MENU

From the EASY MENU, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table.

Item Description

ASPECT

D-ZOOM

KEYSTONE

Using the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE menu (

Using the ◄/► cursor buttons adjusts the magnication ratio.

Small ó Large

See the D-ZOOM item in the SETUP menu (

• The on-screen menu might be displayed outside of the image display area depending on the adjustment value of the ASPECT, D-ZOOM and D-ZOOM and

Using the ◄/► buttons corrects the vertical keystone distortion. See the

KEYSTONE. Changing the values of ASPECT, KEYSTONE may x the symptom.

KEYSTONE item in SETUP menu (



37).



44).



45).

(continued on next page)

QM00611-1

Item Description

Using the ◄/► buttons switches the picture mode. The picture modes are combinations of GAMMA and COLOR TEMP settings. Choose a suitable mode according to the projected source.

NORMAL ó CINEMA ó DYNAMIC ó BOARD(BLACK)

EASY MENU

PICTURE MODE

PHOTO ó DAYTIME ó WHITEBOARD ó BOARD(GREEN)

• When the combination of GAMMA and COLOR TEMP differs from pre-assigned modes above, the display on the menu for the PICTURE MODE is “CUSTOM”. Please refer to the GAMMA and COLOR TEMP (

34, 35) items in PICTURE menu.



• Lines or other noise might appear on the screen when this function is operated, but it is not a malfunction.

Using the ◄/► buttons changes the eco mode setting. See the ECO MODE item of the LAMP & FILTER item in SETUP

ECO MODE

menu (



46).

• When the ambient temperature is around 35 to 40°C, the brightness of lamp is reduced automatically.

INSTALLATION

Pressing the ► button displays the INSTALLATION dialog. See the INSTALLATION item in SETUP menu (

Performing this item resets all of the EASY MENU items except the

RESET

FILTER TIME and LANGUAGE. A dialog is displayed for conrmation. Selecting the OK using the ► button performs resetting.

The usage time of the air lter is shown in the menu. Performing this item resets the lter time which counts usage time of the air lter.

FILTER TIME

A dialog is displayed for conrmation. Selecting the OK using the ► button performs resetting. See the FILTER TIME item of the LAMP & FILTER item in SETUP

LANGUAGE

menu ( Using the ◄/► buttons changes the display language.

See the LANGUAGE item in SCREEN menu (



47).

Press the ► or ENTER button to use the menu of PICTURE,

ADVANCED MENU

IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK or SECURITY.

EXIT Press the ◄ or ENTER button to nish the OSD menu.



48).

52).

QM00611-1

PICTURE menu

From the PICTURE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

◄/►

BRIGHTNESS

CONTRAST

HDCR

ACCENTUALIZER

GAMMA

Using the

Dark ó Light

Using the

Weak ó Strong

A function to show a clear picture in a bright room. Using the◄/► buttons adjusts the contrast.

• This function may not work properly when IMAGE OPTIMIZER is enabled.

ACCENTUALIZER is a function to improve the legibility. Using the ◄/► buttons adjusts the sharpness. Weak ó Strong

• There may be some noise and/or the screen may icker for a moment when an adjustment is made. This is not a malfunction.

• This function may not work properly when IMAGE OPTIMIZER is enabled.

Using the ▲/▼ buttons switches the gamma mode.

To adjust CUSTOM

Selecting a mode whose name includes CUSTOM and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the mode. This function is useful when you want to change the brightness of particular tones.

Choose an item using the ◄/► buttons, and adjust the level using the ▲/▼ buttons.

You can display a test pattern for checking the effect of your adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below.

No pattern ð Gray scale of 9 steps Ramp  Gray scale of 15 steps

The eight equalizing bars correspond to eight tone levels of the test pattern (Gray scale of 9 steps) except the darkest in the left end. If you want to adjust the 2nd tone from left end on the test pattern, use the equalizing adjustment bar “1”. The darkest tone at the left end of the test pattern cannot be controlled with any of equalizing adjustment bar.

• Lines or other noise might appear on the screen when this function is operated, but it is not a malfunction.

buttons adjusts the brightness.

◄/►

buttons adjusts the contrast.

QM00611-1

Item Description

Using the ▲/▼ buttons switches the color temperature mode.

To adjust CUSTOM

Selecting a mode whose name includes CUSTOM and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the OFFSET and GAIN of the selected mode.

OFFSET adjustments change the color intensity on the whole tones of the test pattern.

GAIN adjustments mainly affect color intensity on the brighter tones

COLOR TEMP

of the test pattern. Choose an item using the ◄/► buttons, and adjust the level using

the ▲/▼ buttons. You can display a test pattern for checking the effect of your

adjustment by pressing the ENTER button. Each time you press the ENTER button, the pattern changes as below.

No pattern ð Gray scale of 9 steps

Ramp  Gray scale of 15 steps

• Lines or other noise might appear on the screen when this function is operated, but it is not a malfunction.

Using the ◄/► buttons adjusts the strength of whole color.

Weak ó Strong

• This item can be selected only for a video and component video

COLOR

signal.

For an HDMITM signal, this item can also be selected if either (1) or (2) applies.

• (1) HDMI FORMAT item in the INPUT menu is set to VIDEO. (2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

projector recognizes that it receives video signals.

Using the ◄/► buttons adjusts the tint.

Reddish ó Greenish

• This item can be selected only for a video and component video

TINT

signal.

•

For an HDMITM signal, this item can also be selected if either (1) or (2) applies. (1) HDMI FORMAT item in the INPUT menu is set to VIDEO. (2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

projector recognizes that it receives video signals.

PICTURE menu

(continued on next page)

QM00611-1

PICTURE menu

Item Description

Using the ◄/► buttons adjusts the sharpness.

SHARPNESS

Weak ó Strong

• There may be some noise and/or the screen may icker for a moment when an adjustment is made. This is not a malfunction.

Using the ▲/▼ cursor buttons changes the active iris control mode.

PRESENTATION ó THEATER ó OFF

PRESENTATION : The active iris displays the best presentation

ACTIVE IRIS

THEATER : The active iris displays the best theater image for

image for both bright and dark scenes.

both bright and dark scenes.

OFF : The active iris is always open.

• The screen may icker when the PRESENTATION or THEATER modes are selected. If this occurs select OFF.

This projector has 4 memories for adjustment data (for all the items of the PICTURE menu). Selecting a function using the ▲/▼ buttons and pressing the ► or ENTER button performs each function.

SAVE-1 ó SAVE-2 ó SAVE-3 ó SAVE-4 LOAD-4 óLOAD-3 ó LOAD-2 ó LOAD-1

SAVE-1, SAVE-2, SAVE-3, SAVE-4 Performing a SAVE function saves the current adjustment data into the memory linked in the number included in the function’s name.

• Remember that the current data being stored of a memory will be lost by saving new data into the memory.

MY MEMORY

LOAD-1, LOAD-2, LOAD-3, LOAD-4 Performing a LOAD function loads the data from the memory linked in the number included in the function’s name, and adjusts the picture automatically depending on the data.

• The LOAD functions whose linked memory has no data are skipped.

• Remember that the current adjusted condition will be lost by loading data. If you want to keep the current adjustment, please save it before performing a LOAD function.

• There may be some noise and the screen may icker for a moment when loading data. This is not malfunction.

• You can perform the LOAD function using MY BUTTON. Please see MY BUTTON item in OPTION menu (



60).

QM00611-1

IMAGE menu

From the IMAGE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

Using the ▲/▼ buttons switches the mode for aspect ratio.

For a computer signal

NORMAL ó 4:3 ó 16:9 ó 16:10 ó NATIVE

For an HDMITM signal

ASPECT

OVER SCAN

NORMAL

4:3

For a video signal or component video signal

4:3 ó 16:9 ó 16:10 ó 14:9 ó NATIVE

For an input signal from the LAN, USB TYPE A or USB TYPE B port, or if there is no signal

MC-CX301: 4:3 (xed) MC-CW301: 16:10 (xed)

• The NORMAL mode keeps the original aspect ratio of the signal. Using the ◄/► buttons adjusts the over-scan ratio.

Small (It magnies picture) ó Large (It reduces picture)

• This item can be selected only for a video and component video signal.

• For an HDMI (2) applies. (1) HDMI FORMAT item in the INPUT menu is set to VIDEO. (2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the

projector recognizes that it receives video signals.

signal, this item can also be selected if either (1) or

16:9

16:10

ó NATIVE

14:9

IMAGE menu

(continued on next page)

QM00611-1

IMAGE menu

Item Description

Using the ◄/► buttons adjusts the vertical position.

• Over-adjusting the vertical position may cause noise to appear on the screen. If this occurs, please reset the vertical position to the default setting. Pressing the RESET button when the V POSITION

V POSITION

is selected will reset the V POSITION to the default setting.

• When this function is performed on a video signal, the range of this adjustment depends on OVER SCAN ( possible to adjust when OVER SCAN is set to 10.

•

This function is unavailable for a signal from the LAN, USB TYPE A,

USB TYPE B or HDMI 1/2 port. Using the ◄/► buttons adjusts the horizontal position.

• the screen. If this occurs, please reset the horizontal position to the default setting. Pressing the RESET button when the H POSITION is

H POSITION

selected will reset the H POSITION to the default setting.

• When this function is performed on a video signal, the range of this adjustment depends on OVER SCAN ( possible to adjust when OVER SCAN is set to 10.

• USB TYPE B or HDMI 1/2 por

(continued on next page)

Down ó Up

37) setting. It is not



Right ó Left

Over-adjusting the horizontal position may cause noise to appear on

37) setting. It is not



This function is unavailable for a signal from the LAN, USB TYPE A,

QM00611-1

Item Description

Using the

◄/►

buttons adjusts the horizontal phase to eliminate icker.

Right ó Left

H PHASE

• This item can be selected only for a computer signal or a component video signal. This function is unavailable for a signal from the LAN, USB TYPE A, USB TYPE B or HDMI 1/2 port.

Using the ◄/► buttons adjusts the horizontal size.

Small ó Large

• This item can be selected only for a computer signal. This function is unavailable for a signal from the LAN, USB TYPE A, USB TYPE

H SIZE

B or HDMI 1/2 port.

• When this adjustment is excessive, the picture may not be displayed correctly. In such a case, please reset the adjustment by pressing the RESET button on the remote control during this operation.

• Images might appear degraded when this function is operated, but it is not a malfunction.

Selecting this item performs the automatic adjustment feature.

For a computer signal

For a video signal

The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO is selected for the VIDEO FORMAT item in the INPUT

AUTO ADJUST

EXECUTE

menu (

automatically set to the default.

For a component video signal

The vertical position and horizontal position will be automatically

41).



The vertical position and horizontal position will be

set to the default. The horizontal phase will be automatically adjusted.

• The automatic adjustment operation requires approx. 10 seconds. Also please note that it may not function correctly with some input.

• When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

• When this function is performed for a computer signal, a black frame may be displayed on the edge of the screen, depending on the PC model.

• The items adjusted by this function may vary when the FINE or DISABLE is selected for the AUTO ADJUST item of the SERVICE item in the OPTION menu (



IMAGE menu

64).

QM00611-1

INPUT menu

From the INPUT menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

Using the ▲/▼ buttons switches the progress mode.

TV ó FILM ó OFF

•

This function works only for a video signal, component video signal

PROGRESSIVE

VIDEO NR

COLOR SPACE

(of 480i@60 or 576i@50 or 1080i@50/60) and an HDMI 480i@60 or 576i@50 or 1080i@50/60)

• When TV or FILM is selected, the screen image will be sharp. FILM adapts to the 2-3 Pull-Down conversion system. But these may cause a certain defect (for example, jagged line) of the picture for a quick moving object. In such a case, please select OFF, even though the screen image may lose sharpness.

Using the ▲/▼ buttons switches the noise reduction mode.

HIGH ó MID ó LOW

• This function works only for a video signal, component video signal (of 480i@60 or 576i@50 or 1080i@50/60) and an HDMI 480i@60 or 576i@50 or 1080i@50/60).

Using the ▲/▼ buttons switches the mode for color space.

AUTO ó RGB ó SMPTE240 ó REC709 ó REC601

• This item can be selected only for a computer signal, component video signal(except for signals from the LAN, USB TYPE A and USB TYPE B ports) or an HDMI™ signal.

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well at some signals. In such a case, it might be good to select a suitable mode except AUTO.

signal (of

(continued on next page)

QM00611-1

Item Description

The video format for VIDEO IN port can be set. Using the ◄/► buttons switches

the mode for video

format.

INPUT menu

VIDEO FORMAT

HDMI FORMAT

HDMI RANGE

AUTO ó NTSC ó PAL ó SECAM N-PAL ó M-PAL ó NTSC4.43

•

This item is performed only for a video signal from the VIDEO IN port.

• The AUTO mode automatically selects the optimum mode.

• The AUTO operation may not work well for some signals. If the picture becomes unstable (e.g. an irregular picture, lack of color), please select the mode according to the input signal.

The video format of HDMITM input signals from the HDMI 1 and 2 ports can be set. (1) Use the ▲/▼ buttons to select the HDMI port to be set. (2) Use the ◄/►buttons to select the video format.

AUTO ó VIDEO ó COMPUTER

AUTO: automatically sets the optimum mode.

VIDEO: sets the suitable mode for DVD signals.

COMPUTER: sets the suitable mode for computer signals.

• When the COMPUTER is selected, the functions COLOR (PICTURE menu), TINT (PICTURE menu) and OVER SCAN (IMAGE menu) are unavailable.

The digital range of HDMI

input signals from the HDMI 1 and 2 ports can be set. (1) Use the ▲/▼ buttons to select the HDMI port to be set. (2) Use the ◄/►buttons to select the digital range. AUTO ó NORMAL ó ENHANCED

AUTO: automatically sets the optimum mode. NORMAL: sets the suitable mode for DVD signals. (16-235) ENHANCED: sets the suitable mode for computer signals. (0-255)

• If the contrast of the screen image is too strong or too weak, try finding a more suitable mode.

(continued on next page)

QM00611-1

INPUT menu

Item Description

The computer input signal type for COMPUTER IN1 and IN2 ports can be set. (1) Use the ▲/▼ buttons to select the COMPUTER IN port to be set. (2) Use the ◄/► buttons to select

COMPUTER IN

• Selecting the AUTO mode allows you to input a sync on G signal or component video signal from the port (

• In the AUTO mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so that no signal is received and select the SYNC ON G OFF, and then reconnect the signal.

Set the frame lock function on/off for each port. (1) Use the ▲/▼ buttons to select

(2) Use the ◄/► buttons to turn the

FRAME LOCK

• This item can be performed only on a signal with a vertical frequency of 49 to 51Hz, 59 to 61 Hz.

• When ON is selected, moving pictures are displayed more smoothly.

• This function is unavailable for a signal from the HDMI (of 480i@60 or 576i@50 or 1080i@50/60) port.

(continued on next page)

the computer input signal type. (COMPUTER IN1) AUTO ó SYNC ON G OFF (COMPUTER IN2) AUTO ó SYNC ON G OFF ó MONITOR OUT

13).



the input ports.

frame lock function on/off .

ON ó OFF

QM00611-1

Item Description

The resolution for the COMPUTER IN1 and COMPUTER IN2 input signals can be set on this projector.

(1) In the INPUT menu select the RESOLUTION using the ▲/▼

buttons and press the ► button.

The RESOLUTION menu will be

displayed.

(2) In the RESOLUTION menu select the

resolution you wish to display using

the ▲/▼ buttons.

Selecting AUTO will set a resolution

appropriate to the input signal.

(3) Pressing the ► or ENTER button when

selecting a STANDARD resolution will

automatically adjust the horizontal and

vertical positions, clock phase and

horizontal size.

The INPUT_INFORMATION dialog will be displayed.

(4) To set a custom resolution use the ▲/▼ buttons to select

RESOLUTION

the CUSTOM and the RESOLUTION_CUSTOM box will be

displayed.

Set the horizontal (HORZ) and vertical (VERT) resolutions using the ▲/▼/◄/► buttons. This function may not support all resolutions.

(5) Move the cursor to OK on screen and press the ► or ENTER

button. The message "ARE YOU SURE YOU WISH TO

CHANGE RESOLUTION?" appears. To save the setting, press

the ► button.

The horizontal and vertical positions, clock phase and horizontal

size will be automatically adjusted.

The INPUT_INFORMATION dialog will be displayed.

(6) To revert back to the previous resolution without saving changes,

move the cursor to CANCEL on screen and press the ◄ or

ENTER button.

The screen will then return to the RESOLUTION menu displaying

the previous resolution.

• For some pictures, this function may not work well.

INPUT menu

STANDARD

↓

CUSTOM

↓

QM00611-1

SETUP menu

From the SETUP menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

Using the ◄/► cursor buttons adjusts the magnication ratio.

Small ó Large

D-ZOOM

D-SHIFT

PICTURE POSITION

(MC-CX301)

• The on-screen menu might be displayed outside of the image display area depending on the adjustment value of the ASPECT, D-ZOOM and D-ZOOM and

Using the ◄/►/▲/▼ cursor buttons adjusts the picture position.

• The D-SHIFT adjustment values are not valid when the D-ZOOM is set to 256 (full screen). (MC-CX301)

• The D-SHIFT adjustment values are not valid when the D-ZOOM is set to 320 (full screen). (MC-CW301)

Using the ▲/▼ cursor buttons selects the vertical picture position.

TOP ó MID ó BOTTOM

The PICTURE POSITION is not changed if any of the following cases apply.

• The ASPECT is set to 4:3.

• The input signal has an aspect ratio of 4:3 or vertically larger than 4:3, while the ASPECT is set to NORMAL.

• Vertical size of the displayed image is full on the effective display area, while the ASPECT is set to NATIVE.

• One of the following messages is displayed on the screen: "NO INPUT IS DETECTED" "SYNC IS OUT OF RANGE" "INVALID SCAN FREQ."

• The BLANK or TEMPLATE function is selected.

KEYSTONE. Changing the values of ASPECT,

KEYSTONE may x the symptom.

(continued on next page)

QM00611-1

Item Description

Using the ▲/▼ cursor buttons selects the horizontal picture position.

The PICT. POSIT. H is not changed if any of the following cases apply.

• The ASPECT is set to 16:9 or 16:10.

PICT. POSIT. H

(MC-CW301)

• The input signal has an aspect ratio of 16:9, 16:10 or verticallly smaller than 16:10, while ASPECT is set to NORMAL.

• Horizontal size of the displayed image is full on the effective display area, while the ASPECT is set to NATIVE.

• One of the following messages is displayed on the screen: "NO INPUT IS DETECTED" "SYNC IS OUT OF RANGE" "INVALID SCAN FREQ."

• The BLANK or TEMPLATE function is selected. Using the ◄/► buttons corrects the vertical keystone distortion.

KEYSTONE

• The adjustable range of this function will vary among inputs. For some input, this function may not work well.

(continued on next page)

SETUP menu

LEFT ó MID ó RIGHT

Shrink the bottom of the image ó Shrink the top of the image

QM00611-1

SETUP menu

AUTO ECO

LAMP &

FILTER

ECO MODE

Item Description

Using the ▲/▼ buttons turns on/off the AUTO ECO MODE.

ON ó OFF

• When ON is selected, the projector will always be set to Eco-

MODE

2 mode at start-up regardless of the ECO MODE ( ting. An OSD message “AUTO ECO MODE” will be displayed for tens of seconds when the projector starts with this function activated.

Using the ▲/▼ buttons switches the ECO MODE. OFF ó ECO-1 ó ECO-2<=>INTELLIGENT ECO óSAVER

• When the ECO-1/2 is selected, acoustic noise and screen brightness are reduced.

• When INTELLIGENT ECO is selected, the brightness of the lamp changes according to the level of the input signal. The lamp becomes brighter when the input signal level is high and darker when the level is low. If dark images are projected continuously, the brightness of the lamp may increase to maintain its performance.

• When SAVER is selected, you can select the time within 1 to 30 min. for SAVER MODE using the ► button. If the image signal level doesn’t change more than the period set, the lamp brightness is reduced and electric power consumption decreased. If the image signal level changes or any buttons are operated, the lamp will brighten again. If dark images are projected continuously, the brightness of the lamp may increase to maintain its performance.

• When AUTO ECO MODE (

above) is set to ON, the projector



will always be set to Eco-2 mode at start-up regardless this setting.

• When the ambient temperature is around 35 to 40°C, the brightness of lamp is reduced automatically.



46) set-

(continued on next page)

QM00611-1

LAMP &

FILTER

Item Description

The lamp time is the usage time of the lamp, counted after the last resetting. Pressing the RESET button on the remote control or the ► button of the projector displays a dialog. To reset the lamp time, select the OK using the ► button.

CANCEL ð OK

LAMP TIME

• Please reset the lamp time only when you have replaced the lamp, for a suitable indication about the lamp.

• For the lamp replacement, see the section "Replacing the lamp" (



96).

• The IMAGE OPTIMIZER function does not work properly unless LAMP TIME is initialized when replacing a lamp.

The lter time is the usage time of the air lter, counted after the last resetting. Pressing the RESET button on the remote control or the ► button of the projector displays a dialog.

FILTER

TIME

To reset the lter time, select the OK using the ► button.

CANCEL

• Please reset the lter time only when you have cleaned or replaced the air lter, for a suitable indication about the air lter.

• For the air lter cleaning, see the section “Cleaning and replacing the air lter” (



98).

SETUP menu

FILTER

MESSAGE

FILTER MESSAGE

Use the ▲/▼ button to set the timer for notifying by the message when to replace the lter unit

100h ó • • • ó 5000h ó OFF

After choosing an item except OFF, the message “REMINDER

*** HRS PASSED ....” will appear after the timer reaches the

interval time set by this feature (



103). When the OFF is chosen, the message will not appear. Utilize this feature to keep the air lter clean, setting the suitable time according to your environment of this projector.

• Please take care of the lter unit periodically, even if there is no message. If the air lter becomes to be blocked by dust or other matter, the internal temperature will rise, which could cause malfunction, or reduce the lifetime of the projector.

• Please be careful with the operating environment of the projector and the condition of the lter unit.

QM00611-1

SETUP menu

Item Description

When this function is enabled, automatic image correction is performed to maintain visibility in accordance with lamp deterioration.

IMAGE

OPTIMIZER

• This function may not work properly when HDCR/ ACCENTUALIZER is set to other than 0.

• This function does not work properly unless LAMP TIME is initialized when replacing a lamp.

Pressing the ►button displays the dialog for changing the INSTALLATION setting.

INSTALLATION

Use the ▲/▼ buttons to select the desired setting on the INSTALLATION dialog.

(continued on next page)

QM00611-1

Item Description

Using ▲/▼ buttons switches the standby mode setting between NORMAL and SAVING.

When SAVING is selected, the power consumption in the standby mode is lowered with some functional restriction as below:

• When SAVING is selected, the RS-232C communication control except to turn the projector on and the network function are disabled while the projector is in the standby mode. If the COMMUNICATION TYPE in the COMMUNICATION menu is set to NETWORK

STANDBY MODE

BRIDGE, all of the RS-232C commands are disabled (

• When SAVING is selected, STANDBY setting of AUDIO SOURCE (



sound from a built-in speaker.

• When SAVING is selected, STANDBY setting of MONITOR OUT is invalid, and no signal is output from MONITOR OUT port in the standby mode.

• The USB connection is disabled while the projector is in standby mode if the STANDBY MODE item in the SETUP menu of the projector is set to SAVING.

• When SAVING is selected, CLONING load function is invalid while in STANDBY MODE.

(continued on next page)

SETUP menu

NORMAL ó SAVING

67).



50) is invalid, no signal is output from AUDIO OUT port and no

QM00611-1

AUDIO menu

From the AUDIO menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or the ENTER button to execute the item. Then perform it according to the following table.

Item Description

VOLUME

SPEAKER

AUDIO SOURCE

Using the ◄/► buttons adjusts the volume.

Low ó High

Using the ▲/▼ buttons turns on/off the built-in speaker.

ON ó OFF

When OFF is selected, the built-in speaker does not work. While the image signal from the input port chosen in step (1) is

projected, the audio signal from the input port selected in step (2) is output to both the AUDIO OUT port and built-in speaker of this projector. However, the built-in speaker does not work when SPEAKER is set to OFF. (1) Choose a picture input port using the

▲/▼ buttons. Choose STANDBY to select the sound output in the standby mode.

(2) Select an audio input port or the mute

icon using the ◄/► buttons. The icons indicate the following;

No.1: AUDIO IN1 port No.2: AUDIO IN2 port No.3: LAN port No.4: USB TYPE A port No.5: USB TYPE B port No.6: HDMI 1 port No.7: HDMI 2 port : mutes the sound

• Audio input from port nos 3 to 7 can only be selected by each of the picture input ports.

• Even if the projector is in the standby mode, cooling fans may work and make noises when the built-in speaker is in operation.

• C.C. (Closed Caption) is automatically activated when and an input signal containing C.C. is received. This function is available only when the signal is NTSC for VIDEO or 480i@60 for COMPUTER IN1 or COMPUTER IN2, and when AUTO is selected for DISPLAY in the C.C. menu under the SCREEN menu (

is selected

57).



(continued on next page)

QM00611-1

Item Description

Using the ▲/▼ buttons switches the input level to match that of the microphone connected to the MIC port.

MIC LEVEL

HIGH ó LOW

HIGH: for a microphone with an amplier. LOW: for a microphone without an amplier.

Using the ◄/► buttons adjusts the volume of the microphone

MIC VOLUME

connected to the MIC port.

Low ó High

AUDIO menu

QM00611-1

SCREEN menu

From the SCREEN menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

Using the ▲/▼/◄/► buttons switches the OSD (On Screen Display) language.

LANGUAGE

MENU POSITION

BLANK

AUTO BLANK

ENGLISH ó FRANÇAIS ó DEUTSCH ó ESPAÑOL

(shown in the LANGUAGE dialog)

Press the ENTER or INPUT button to save the language setting. Using the ▲/▼/◄/► buttons adjusts the menu position.

To quit the operation, press the MENU button on the remote control or keep no operation for about 10 seconds.

Using the ▲/▼ buttons switches the mode for the blank screen. The blank screen is a screen for the temporarily blanking feature

22). It is displayed by pressing the AV MUTE button on the

(



remote control.

MyScreen ó ORIGINAL ó BLUE ó WHITE ó BLACK

MyScreen : ORIGINAL : Screen preset as the standard screen. BLUE, WHITE, BLACK : Plain screens in each color.

• To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the plain black screen after several minutes.

Using the ▲/▼ buttons switches the mode for the AUTO BLANK screen. BLUE ó WHITE ó BLACK

• To avoid remaining as an afterimage, displayed image will change to the designated blank color screen by AUTO BLANK after several minutes at the following conditions.

- When MyScreen or ORIGINAL is displayed as BLANK screen.

- When start-up screen is displayed.

Screen can be registered by the MyScreen item (



53).

(continued on next page)

QM00611-1

Item Description

Using the ▲/▼ buttons switches the mode for the start-up screen. The start-up screen is a screen displayed when no signal or an unsuitable signal is detected.

MyScreen ó ORIGINAL ó OFF

START UP

MyScreen : ORIGINAL : Screen preset as the standard screen. OFF : Plain black screen.

Screen can be registered by the MyScreen item (

• To avoid remaining as an afterimage, the MyScreen or ORIGINAL screen will change to the BLANK screen ( minutes. If also the BLANK screen is the MyScreen or ORIGINAL, the plain black screen is instead used.

• When the ON is selected to the MyScreen PASSWORD item in the SECURITY menu (

74), the START UP is fixed to MyScreen.



This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure.

Selecting this item displays a dialog titled “MyScreen”. It will ask you if you start capturing an image from the current screen. Please wait for the target image to be displayed, and press the ENTER or INPUT button to start registration. To restore the screen and return to the previous dialog, press the

MyScreen

RESET button on the remote control.

Registration may take several minutes. When the registration is completed, the registered screen and the following message is displayed for several seconds:

“MyScreen registration is nished.”

If the registration failed, the following message is displayed:

“A capturing error has occurred. Please try again.”

• This function cannot be selected when the ON is selected to the MyScreen Lock item (



54).

• This function cannot be selected when the ON is selected to the MyScreen PASSWORD item in SECURITY menu (

•

This function is unavailable for a signal from the LAN, USB TYPE A,

USB TYPE B or HDMI 1/2 port.



above

) after several



SCREEN menu

53).



74).

(continued on next page)

QM00611-1

SCREEN menu

Item Description

Using the ▲/▼ buttons turns on/off the MyScreen lock function.

ON ó OFF

MyScreen Lock

When the ON is selected, the item MyScreen is locked. Use this function for protecting the current MyScreen.

• This function cannot be selected when the ON is selected to the MyScreen PASSWORD item in SECURITY menu (

Using the ▲/▼ buttons turns on/off the message function.

ON ó OFF

When the ON is selected, the following message function works.

“AUTO IN PROGRESS” while automatically adjusting “NO INPUT IS DETECTED” “SYNC IS OUT OF RANGE” “INVALID SCAN FREQ.” “NOT AVAILABLE” “Searching….” while searching for the input “Detecting….” while an input signal is detected

MESSAGE

“AUTO ECO MODE” while starting up with AUTO ECO MODE The indication of the input signal displayed by changing The indication of the aspect ratio displayed by changing The indication of the PICTURE MODE displayed by changing The indication of the ACTIVE IRIS displayed by changing The indication of the MY MEMORY displayed by changing The indication of “FREEZE” and “II” while freezing the screen by pressing the FREEZE button. The indication of the TEMPLATE displayed by changing. The indication of the ECO MODE displayed by changing. The D-ZOOM dialog displayed by changing

• When the OFF is selected, please remember if the picture is frozen. Do not mistake freezing for a malfunction (



74).

29).

(continued on next page)

QM00611-1

Item Description

Each input port for this projector can have a name applied to it. (1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE

NAME and press the ► or ENTER button. The SOURCE NAME menu will be displayed.

(2) Use the ▲/▼ buttons on the SOURCE

NAME menu to select the port to be named and press the ► button. The SOURCE NAME dialog will be displayed.

Right side of the menu is blank until a name is specied.

(3) Select an icon you would like to assign to

SOURCE NAME

the port in the SOURCE NAME dialog. The name assigned to the port will also be automatically switched according to your icon selection. Press the ENTER or INPUT button to determine your icon selection.

(4) Select a number you would like to assign

to the port along with the icon. You can select the number either from blank (no number assigned), 1, 2, 3, or 4. Then press the ENTER or INPUT button.

(5) If you would like to modify the name assigned

to the port, select CUSTOM NAME and press the ENTER or INPUT button.

SCREEN menu

(continued on next page)

QM00611-1

SCREEN menu

Item Description

(6) The current name will be displayed on

the rst line. Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. To erase 1 character at one time, press the RESET button or press the ◄ and INPUT button at the same time. Also if you move the cursor to DELETE or ALL CLEAR on screen and press the ENTER or INPUT button, 1 character or all characters will be erased. The name can be a maximum

SOURCE NAME

(Continued)

of 16 characters.

(7) To change an already inserted character,

press the ▲ button to move the cursor to the rst line, and use the ◄/► buttons to move the cursor on the character to be

changed. After pressing the ENTER or INPUT button, the character is selected. Then, follow the same procedure as described at the item (6) above.

(8) To nish entering text, move the cursor to the OK on screen and

press the ►, ENTER or INPUT button. To revert to the previous

name without saving changes, move the cursor to the CANCEL

on screen and press the ◄, ENTER or INPUT button.

Using the ▲/▼ cursor buttons switches the mode for the template screen. Press the ► cursor (or the ENTER) button to display the selected template, and press the ◄ cursor button to close the displayed screen.

TEMPLATE

TEST PATTERN ó DOT-LINE1 ó DOT-LINE2 ó DOT-LINE3



MAP2 ó MAP1 ó CIRCLE2 ó CIRCLE1 ó DOT-LINE4

You can turn a map upside down and scroll it horizontally when MAP1 or MAP2 is selected. To invert or scroll the map, display the guidance by pressing the RESET button on the remote three seconds or more when MAP1 or MAP2 appears.



(continued on next page)

QM00611-1

Item Description

The C.C. is the function that displays a transcript or dialog of the audio portion of a video, les or other presentation or other relevant sounds. It is required to have NTSC format video or 480i@60 format component video source supporting C.C. feature to utilize this function. It may not work properly, depending on equipment or signal source. In this case, please turn off the Closed Caption.

DISPLAY

Select Closed Caption DISPLAY setting from following options using ▲/▼ buttons.

AUTO ó ON ó OFF

AUTO : Closed Caption automatically appears when the input

signal (C.C. compatible) from the port with the mute icon

set at AUDIO SOURCE is selected. ON : Closed Caption is on. OFF : Closed Caption is off.

• The caption is not displayed when the OSD menu is active.

• The Closed Caption is the function to display the dialogue,

C.C.

(Closed Caption)

narration, and / or sound effects of a television program or other video sources. The Closed Caption availability is depending upon broadcaster and/or content.

MODE

Select Closed Caption MODE setting from following options using ▲/▼ buttons.

CAPTIONS ó TEXT CAPTIONS : Display Closed Caption.

TEXT : Display Text data, which is for additional information such

as news reports or a TV program guide. The information covers the entire screen. Not all of the C.C. program has Text information.

CHANNEL

Select Closed Caption CHANNEL from following options using ▲/▼ buttons.

1 ó 2 ó 3 ó 4

SCREEN menu

1: Channel 1, primary channel / language 2: Channel 2 3: Channel 3

4: Channel 4

The channel data may vary, depending on the content. Some channel might be used for secondary language or empty.

QM00611-1

OPTION menu

From the OPTION menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.

Item Description

Using the ▲/▼ buttons turns on/off the automatic signal search function.

ON ó OFF

When the ON is selected, detecting no signal automatically cycles

AUTO SEARCH

DIRECT POWER

through input ports in the following order. The search is started from the current port. Then when an input is found, the projector will stop searching and display the image.

COMPUTER IN1 ð COMPUTER IN2 ð LAN ð USB TYPE A

VIDEO  HDMI 2  HDMI 1  USB TYPE B

• It may take several seconds to project the images from the USB TYPE B port.

Using the ▲/▼ buttons turns on/off the DIRECT POWER ON function.

ON ó OFF

When set to the ON, the lamp in projector will be automatically turned on without the usual procedure ( supplied with the power after the power was cut while the lamp was on.

• This function does not work as long as the power has been supplied to the projector while the lamp is off.

•

After turning the lamp on by the DIRECT if neither input nor operation is detected for about 30 minutes, the projector is turned off, even though the AUTO

59) is disabled.

(



20), only when the projector is



POWER

ON function,

OFF function

(continued on next page)

QM00611-1

Item Description

Using the ▲/▼ buttons adjusts the time to count down to automatically turn the projector off.

Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE)

OPTION menu

AUTO POWER

OFF

When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with nosignal or an unsuitable signal reaches at the set time, the projector lamp will be turned off. If one of the projector's buttons or the remote control buttons is pressed or one of the commands (except get commands) is transmitted to the CONTROL port during the corresponding time, projector will not be turned off. Please refer to the section “Turning off the power”

(continued on next page)

21).

(



QM00611-1

OPTION menu

Item Description

This item is to assign one of the following functions to MY BUTTON 1/2 on the remote control (

(1) Use the ▲/▼ buttons on the MY BUTTON menu to select a MY

BUTTON - (1/2) and press the ► or ENTER button to display the MY BUTTON setup dialog.

(2) Then using the ▲/▼/◄/► buttons sets one of the following

functions to the chosen button. Press the ENTER or INPUT button to save the setting.

• COMPUTER IN1: Selects the input from COMPUTER IN1 port.

• COMPUTER IN2: Selects the input from COMPUTER IN2 port.

• LAN: Selects input from LAN port.

• USB TYPE A: Selects input from USB TYPE A port.

• USB TYPE B: Selects input from USB TYPE B port.

• HDMI1: Selects input from HDMI 1 port.

• HDMI2: Selects input from HDMI 2 port.

• VIDEO: Selects the input from VIDEO IN port.

• SLIDESHOW: Selects the input from USB TYPE A port, and starts

a Slideshow.

MY BUTTON

• MY IMAGE: Displays the MY IMAGE menu.

• MESSENGER:

Messenger Function in the User's Manual - Network Guide

(



Turns the messenger text displayed on the screen on/off

When there is no transferred text data to display, the message ”NO MESSENGER DATA" appears.

• INFORMATION: Displays SYSTEM_INFORMATION,

INPUT_INFORMATION ( WIRED INFORMATION or nothing.

• MY MEMORY: Loads one of adjustment data stored (

When more than one data are saved, the adjustment changes every time the MY BUTTON is pressed.

When no data is saved in memory, the

dialog "No saved data" appears.

When the current adjustment is not

saved to memory, the dialog as shown in

the right appears.

If you want to keep the current adjustment, please press

the ► button to exit. Otherwise loading a data will overwrite the

current adjusted condition.

7).



71), WIRELESS INFORMATION,



36).

(continued on next page)

QM00611-1

Item Description

• ACTIVE IRIS: Changes the active iris mode.

• PICTURE MODE: Changes the PICTURE MODE (

•

MY BUTTON

(Continued)

FILTER RESET: Displays the lter time reset conrmation dialogue

• RESOLUTION: Turns on/off the RESOLUTION dialog (

• MIC VOLUME: Turns on/off the MIC VOLUME dialog (

• ECO MODE: Changes the ECO MODE (

• SAVER MODE: Turns on/off the SAVER MODE (

■ How to setup the item

1. Use the ▲/▼/◄/► cursor buttons to select or adjust. 2 Select OK to nish the settings.

• Please refer to the actual on-screen display(OSD)

NOTE

for appropriate operation.

Item Description

DATE AND TIME

SPECIFIC DATE

PROGRAM EDIT

Set the DATE(Year/Month/Date) and Time(24hour scale).

Set specic date from 1 to 10.

The TIME and EVENT for Program 1 to 16 can be editted.

■ How to activate(DATE AND TIME / SPECIFIC DATE)

Place a check mark in the box.

SCHEDULE

Check mark in the box

OPTION menu

33).



43).



51).



46).



46).

Date and rst setup info could be seen with the check mark.

47).

(



1/2 page (Set the DATE(Year/Month/Date) and Time(24-hour scale).)

(continued on next page)

QM00611-1

OPTION menu

Item Description

SCHEDULE

(Continued)

Check mark in the box

2/2 page (Set specic date from 1 to 10.)

Press the ▼ cursor button to move from 1/2 page to 2/2 page with the state of selecting "SATURDAY".

Date and rst setup info could be seen with the check mark.

■ PROGRAM EDIT

The TIME and EVENT for Program 1 to 16 can be editted.

• RETURN

Select this to go back to the top menu of the SCHEDULE.

• SELECT

Select from PROGRAM-01 to 16 to edit. Each PROGRAM can be setup up to 20 settings

• COPY TO

The selected program (with the settings of TIME and EVENT) can be copied to other program.

• APPLY

Select this to apply and save all adjustments and settings.

(continued on next page)

QM00611-1

Item Description

■ How to edit the selected PROGRAM

1. Select from 1 to 20 events.

Use the ▲/▼ cursor buttons to select. Press ► cursor button to set the TIME and EVENT.

2. Use the ◄/► cursor buttons to select.

3. Use the ◄/► cursor buttons to adjust.

EVENT can be selected as listed below.

◦ POWER − ON, STANDBY

◦ INPUT SOURCE − "input source"channel

◦ MY IMAGE − IMAGE-1 to 4, IMAGE OFF

◦ MESSENGER − TEXT-1 to 12, TEXT OFF

SCHEDULE

(Continued)

◦

ECO MODE − OFF, ECO-1, ECO-2, INTELLIGENT ECO,

SAVER

◦ BLANK − ON, OFF

◦ SLIDESHOW − START, STOP

OPTION menu

4. Press ► cursor button to finish the settings.

5. Select APPLY to save the settings.

(continued on next page)

•

NOTE

for appropriate operation.

Please refer to the actual on-screen display(OSD)

QM00611-1

OPTION menu

Item Description

Selecting this item displays the SERVICE menu. Select an item using the ▲/▼ buttons, and press the ► button or the ENTER button on the remote control to execute the item.

ALTITUDE

Using the ▲/▼ buttons switches the rotation speed of the cooling fans. If the projector is used at an altitude of about 1600 m or higher, select HIGH. Otherwise, select NORMAL. Note that the projector is noisier when the HIGH is selected.

HIGH ó NORMAL

AUTO ADJUST

SERVICE

Using the ▲/▼ buttons to select one of the mode. When the DISABLE is selected, the automatic adjustment feature is disabled.

FINE ó FAST ó DISABLE

FINE: Finer tuning including H.SIZE adjustment. FAST: Faster tuning, setting H.SIZE to prearranged data for the

input signal.

• Depending on conditions, such as input image, signal cable to the projector, environment around the projector, etc., the automatic adjustment may not work correctly. In such a case, please choose DISABLE to disable the automatic adjustment, and make adjustment manually.

GHOST

Adjust the settings using the ▲/▼ buttons to eliminate ghosting.

(continued on next page)

QM00611-1

Item Description

KEY LOCK

(1) Use the ▲/▼ buttons to select CONTROL PANEL or REMOTE

(2) Use the ◄/► buttons to turn the key lock function on/off.

SERVICE

(continued)

When ON is selected, all buttons on the projector or remote control except the STANDBY/ON button are locked.

• Please use this function to prevent tampering or accidental operation.

• It is not possible to set both CONTROL PANEL and REMOTE CONTROL to ON.

(continued on next page)

OPTION menu

CONTROL.

QM00611-1

OPTION menu

Item Description

REMOTE FREQ.

(1) Use the ▲/▼ button to change the projector's remote sensor

frequency setting (



1:NORMAL ó 2:HIGH

(2) Use the ◄/► button to change the

projector's remote sensor on or off.

ON ó OFF

The factory default setting is for both 1:NORMAL and 2:HIGH to be on. If the remote control does not function correctly, disable either of them. It's not possible to disable both options at the same time.

Selecting this item displays COMMUNICATION menu. In this menu, you can congure the serial

SERVICE

(continued)

communication settings of the projector using the CONTROL port.

18).

COMMUNICATION

(continued on next page)

• Select an item using the cursor buttons ▲/▼. Then pressing the ► button opens the submenu for the setting item you selected. Or, pressing the ◄ button instead of the ► button makes the menu back to the previous one without changing the setup. Each submenu can be operated as described above.

• When COMMUNICATION TYPE (

67) is set to



OFF, the other items in COMMUNICATION menu are invalid.

• For the function of serial communication, refer to the User's Manual - Network Guide.

QM00611-1

Item Description

SERVICE

COMMUNICATION

(continued)

(continued on next page)

(continued)

OPTION menu

COMMUNICATION TYPE

Select the communication type for transmission via the CONTROL port. NETWORK BRIDGE:

Select this type, if it is required to control an external device as a network terminal, via this projector from the computer. The CONTROL port doesn't accept RS-232C commands (

User’s Manual - Network Guide

Network Bridge Function in the



)

OFF: Select this mode to receive RS-232C

commands using the CONTROL port. OFF is selected as the default setting.

•

• When you select the NETWORK BRIDGE, check the item, TRANSMISSTION METHOD (



below).

SERIAL SETTINGS

Select the serial communication condition for the

CONTROL port.

BAUD RATE

4800bps ó 9600bps ó 19200bps ó 38400bps

PARITY

NONE ó ODD ó EVEN

•

The BAUD RATE is xed to 19200bps and PARITY

is xed NONE when the COMMUNICATION TYPE is set to OFF

(



above).

TRANSMISSION METHOD

Select the transmission method for communication by the NETWORK BRIDGE from the CONTROL port.

HALF-DUPLEX ó FULL-DUPLEX

HALF-DUPLEX: This method lets the projector

make two way communication, but only one direction, either transmitting or receiving data, is allowed at a time.

FULL-DUPLEX: This method lets the projector

make two way communication, transmitting and receiving data at the same time.

• HALF-DUPLEX is selected as the default setting.

• If you select HALF-DUPLEX, check the setting of the item RESPONSE LIMIT TIME (



68).

QM00611-1

OPTION menu

Item Description

RESPONSE LIMIT TIME

Select the time period to wait for receiving response data from other device communicating by the NETWORK BRIDGE and the HALF-DUPLEX through the CONTROL port.

OFF ó 1s ó 2s ó 3s

OFF: Select this mode if it is not required to check

the responses from the device that the projector

COMMUNICATION

(continued)

sends data to. In this mode, the projector can send out data from the computer continuously.

1s /2s /3s: Select the time period to keep the

projector waiting for response from the device that the projector sends data to. While waiting the response, the projector does not send out any

SERVICE

(continued)

data from the CONTROL port.

• This menu is available only when the NETWORK BRIDGE is selected for the COMMUNICATION TYPE and the HALF-DUPLEX is selected for the TRANSMISSION METHOD (

• OFF is selected as the default setting. The setttings of the projector can be coppied via USB

memory.

Saves each settings of the projector to USB

SAVE:

memory. Loads each settings of the projector from

LOAD:

CLONING

USB memory. Message will be displayed after loading, and power will turn off after ve min. or by pressing ► button. (A message is displayed for a few seconds if loading fails.)

After saving / loading, you can remove the USB storage device.



67).

(continued on next page)

QM00611-1

Item Description

The following items are exempted. SETUP: LAMP TIME, FILTER TIME OPTION: SERVICE(GHOST) NETWORK: WIRELESS AND WIRED SETUP

(IP ADDRESS, SUBNET MASK, DEFAULT GATEWAY, DATE AND TIME), MY IMAGE, PRESENTATION

SECURITY: MY TEXT DISPLAY

• Operation is not available if SECURITY_ CLONNING LOCK is turned ON.

• The Screen_MyScreen can only be loaded.

CLONING load function on STANDBY MODE

• While the projector is in STANDBY MODE, push the INPUT button of control panel together with ► button, and then press ▲ button to start operating the CLONING load function.

• During loading process, the three indicators of control panel (POWER (orange), TEMP, LAMP)

SERVICE

(continued)

CLONING

(continued)

will remain on.

• After the loading process, the three indicators (POWER (orange), TEMP, LAMP) will turn off. Then, you can remove the USB storage device.

• If the loading fails, the three indicators (POWER (orange), TEMP, LAMP) will blink at the same time.

• CLONING is invalid with the following conditions.

- CLONING LOCK is turned ON.

With this condition, the three indicators (POWER (orange), TEMP, LAMP) will blink at approximately three seconds intervals.

- If the STANDBY MODE is set to SAVING.

- If there is no USB memory inserted into USB

TYPE A port.

- If PIN LOCK is not being released.

- If a system error occurs.

• Please operate one of the following after loading.

- Press INPUT button and

panel at the same time.

- Wait at least ve min. after loading.

- Restart the projector after re-plugging the AC

cable.

OPTION menu

◄

button of the control

(continued on next page)

QM00611-1

OPTION menu

Item Description

Load MyScreen data

• Please save the image data as "pj_logo.bmp" or "pj_logo.gif" into USB memory.

• Please note that the only compatible formats are as follows.

-File format

Windows BMP bit/pixel: 4/8/16/24/32bit Compression format : Without compression/RLE/GIF

-Image size: more than 36x36, less than 1280x800

• If two kinds of le format are saved, "pj_logo. bmp" will be registered into MyScreen data.

• If MyScreen LOCK or MyScreen PASSWORD is turned ON, the data of MyScreen cannot be loaded.

SERVICE

(continued)

CLONING

(continued)

Setting the data

• Operating the SAVE function under CLONING will name the le as "pj_data.bin" into the USB memory. Please do not attempt to change the le name or the folder structure.

• If a le with the same name already exists, it will be overwritten by operating the SAVE function.

(continued on next page)

Loading function

• Please note that saved data from other model cannot be loaded.

•

Please note that, if any of the following functions: MyScreen PASSWORD, PIN LOCK, MY TEXT PASSWORD under SECURITY menu or MyScreen Lock under SCREEN menu is ON, the respective saved data cannot be loaded.

QM00611-1

Item Description

Loading function (continued)

•

Please note that the saved data of START UP

CLONING

(continued)

and MyScreen Lock under SCREEN menu cannot be loaded if MyScreen PASSWORD under SECURITY menu is ON.

•

Please note that the saved data of MY TEXT WRITING cannot be loaded if MY TEXT PASSWORD under SECURITY menu is ON.

INFORMATION

Selecting this item displays a dialog titled “INPUT_INFORMATION”. It shows the information about the current input.

SERVICE

(continued)

• The “FRAME LOCK” message on the dialog means the frame lock function is working.

• This item can't be selected for no signal and sync out.

• When the MY TEXT DISPLAY is set to ON, the MY TEXT is displayed together with the input information in the INPUT_ INFORMATION box (



77).

FACTORY RESET

Selecting OK using the ► button performs this function. By this function, all the items in all of menus will collectively return to the initial setting. Note that the items LAMP TIME, FILTER TIME, LANGUAGE, FILTER MESSAGE, STANDBY MODE,SCHEDULE,AUTO BLANK, NETWORK and SECURITY settings are not reset.

CANCEL ð OK

Be sure to set ALTITUDE after resetting all the settings (

OPTION menu

64).



QM00611-1

NETWORK menu

See the Network Guide for details of NETWORK operation. Remember that incorrect network settings on this projector may cause trouble on the network. Be sure to consult with your network administrator before connecting to an existing access point on your network.

QM00611-1

SECURITY menu

This projector is equipped with security functions. From the SECURITY menu, items shown in the table below can be performed. To use SECURITY menu: User registration is required before using the security functions.

Enter to the SECURITY menu

1. Press the ► button. The ENTER PASSWORD box will be displayed.

2. Use the ▲/▼/◄/► buttons to enter the registered password. The factory default password is as follows.

MC-CX301: 6431 MC-CW301: 4831

This password can be changed right side of the ENTER PASSWORD box and press the ► button to display the SECURITY menu.

• It is strongly recommended the factory default password to be changed as soon as possible.

• If an incorrect password is input, the ENTER PASSWORD box will be displayed again. If incorrect password is input 3 times, the projector will turn off. Afterwards the projector will turn off every time an incorrect password is input.

3. Items shown in the table below can be performed.

(



If you have forgotten your password

(1). While the ENTER PASSWORD box is displayed, press and hold

the RESET button on the remote control for about 3 seconds or press and hold the INPUT button for 3 seconds while pressing the ► button on the projector.

(2). The 10 digit Inquiring Code will be displayed. Contact your dealer

with the 10 digit Inquiring Code. Your password will be sent after your user registration information is conrmed.

• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will close. If necessary, repeat the process from (1).

. Move the cursor to the

below)

Item Description

(1) Use the ▲/▼ buttons on the SECURITY menu

(2) Use the ▲/▼/◄/► buttons to enter the new password. (3) Move the cursor to the right side of the ENTER

SECURITY

PASSWORD

CHANGE

(4)

• Please do not forget your password.

(continued on next page)

to select SECURITY PASSWORD CHANGE and press the ► button to display the ENTER NEW PASSWORD box.

NEW PASSWORD box and press the ► button to display the NEW PASSWORD AGAIN box, enter the same password again.

Move the cursor to the right side of the NEW PASSWORD AGAIN box and press the ► button and the NOTE NEW PASSWORD box will be displayed for about 30 seconds, please make note of the password during this time.

Pressing the ENTER button on the remote control or ► button on the projector will close the NOTE NEW PASSWORD box.

QM00611-1

SECURITY menu

Item Description

The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten.

1 Turning on the MyScreen PASSWORD

1-1 Use the ▲/▼ buttons on the SECURITY menu to

1-2 Use the ▲/▼ buttons on the MyScreen

1-3 Use the ▲/▼/◄/► buttons to enter the

1-4 Move the cursor to the right side of the

MyScreen

PASSWORD

(continued on next page)

When a password is set for MyScreen:

•

unavailable). Turning the MyScreen PASSWORD off will allow normal operation of these functions.

•

2 Turning off the MyScreen PASSWORD

2-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off

2-2

If an incorrect PASSWORD is input, the menu will close. If necessary, repeat the process from 2-1.

3 If you have forgotten your password

3-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off

3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit

3-3 Contact your dealer with the 10 digit Inquiring Code. Your password will

select MyScreen PASSWORD and press the ► button to display the MyScreen PASSWORD on/ off menu.

PASSWORD on/off menu to select ON. The ENTER NEW PASSWORD box (small) will be displayed.

password. Move the cursor to the right side of the ENTER NEW PASSWORD box (small) and press the ► button to display the NEW PASSWORD AGAIN box, enter the same PASSWORD again.

NEW PASSWORD AGAIN box and press the ► button to display the NOTE NEW PASSWORD box for about 30 seconds, please make note of the password during this time.

Pressing the ENTER button on the remote control or ► button on the projector will return to MyScreen PASSWORD on/off menu.

The MyScreen registration function (and menu) will be unavailable. The MyScreen Lock menu will be unavailable. The START UP setting will be locked on MyScreen (and the menu will be

Please do not forget your MyScreen PASSWORD.

menu.

Select OFF to display the ENTER PASSWORD box (large). Enter the registered password and the screen will return to the MyScreen PASSWORD on/off menu.

menu.

Inquiring Code will be displayed inside the box.

be sent after your user registration information is conrmed.

ENTER NEW PASSWORD

box (small)

ENTER PASSWORD box

(large)

QM00611-1

Item Description

PIN LOCK is a function which prevents the projector from being used unless a registered Code is input.

1 Turning on the PIN LOCK

1-1 Use the ▲/▼ buttons on the SECURITY menu

to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu.

1-2 Use the ▲/▼ buttons on the PIN LOCK on/

off menu to select ON and the Enter PIN Code box will be displayed.

1-3 Input a 4 part PIN code using the ▲/▼/◄/►,

COMPUTER or INPUT button. The PIN Code again box will appear. Reenter the same PIN code. This will complete the PIN code registration.

If there is no key input for about 55 seconds

•

while the Enter PIN Code box or the PIN Code again box is displayed, the menu will close. If necessary, repeat the process from 1-1.

Afterwards, anytime the projector is restarted after AC power is turned off the Enter PIN Code box will be displayed. Enter the registered PIN code. The projector can be used after entering the registered PIN code. If an incorrect PIN code is input, the Enter PIN code box will be displayed again.

PIN LOCK

If an incorrect PIN code is input 3 times, the projector will turn off. Afterwards the projector will turn off every time an incorrect PIN code is input. The projector will also turn off if there is no key input for about 5 minutes while the Enter PIN code box is displayed. This function will activate only when the projector is started after AC power is turned off.

Please do not forget your PIN code.

•

2 Turning off the PIN LOCK

2-1 Follow the procedure in 1-1 to display the PIN LOCK on/off menu. 2-2 Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be

displayed. Enter the registered PIN code to turn the PIN LOCK function off.

If an incorrect PIN code is input 3 times, the projector will turn off.

3 If you have forgotten your PIN code

3-1 While the Enter PIN code box is displayed, press and hold the RESET

button for 3 seconds or press and hold the INPUT button for 3 seconds while pressing the ► button on the projector. The 10 digit Inquiring Code will be displayed.

If there is no key input for about 5 minutes

•

while the Inquiring Code is displayed, the projector will turn off.

3-2 Contact your dealer with the 10 digit Inquiring Code. Your PIN code will

be sent after your user registration information is conrmed.

SECURITY menu

(continued on next page)

QM00611-1

SECURITY menu

Item Description

The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten. When the password is set for the MY TEXT;

• The MY TEXT DISPLAY menu will be unavailable, which can prohibit changing the DISPLAY setting.

• The MY TEXT WRITING menu will be unavailable, which can prevent the MY TEXT from being overwritten.

1 Turning on the MY TEXT PASSWORD

1-1 Use the ▲/▼ buttons on the SECURITY menu to

1-2 Use the ▲/▼ buttons on the MY TEXT

1-3 Use the ▲/▼/◄/► buttons to enter the

MY TEXT

1-4 Move the cursor to the right side of the NEW

PASSWORD

Pressing the ENTER button on the remote control or ► button on the projector will return to the MY TEXT PASSWORD on/off menu.

2 Turning off the MY TEXT PASSWORD

2-1 Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off

2-2 Select OFF to display the ENTER

If an incorrect password is input, the menu will close. If necessary, repeat the process from 2-1

3 If you have forgotten your password

3-1 Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off

3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit

3-3 Contact your dealer with the 10 digit inquiring code. Your password will

(continued on next page)

select the MY TEXT PASSWORD and press the ► button to display the MY TEXT PASSWORD on/off menu.

PASSWORD on/off menu to select ON. The ENTER NEW PASSWORD box (small) will be displayed.

password. Move the cursor to the right side of the ENTER NEW PASSWORD box (small) and press the ► button to display the NEW PASSWORD AGAIN box, and then enter the same password again.

PASSWORD AGAIN box and press ► button to display the NOTE NEW PASSWORD box for about 30 seconds, then please make note of the password during this time.

menu.

PASSWORD box (large). Enter the registered password and the screen will return to the MY TEXT PASSWORD on/off menu.

menu.

inquiring code will be displayed inside the box.

be sent after your user registration information is conrmed.

ENTER NEW PASSWORD

box (small)

ENTER PASSWORD box

(large)

QM00611-1

Item Description

(1) Use the ▲/▼ buttons on the SECURITY menu to

select the MY TEXT DISPLAY and press the ► or ENTER button to display the MY TEXT DISPLAY on/off menu.

(2) Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select

on or off.

MY TEXT DISPLAY

MY TEXT

WRITING

CLONING LOCK

ON ó OFF

When it is set ON, the MY TEXT will be displayed on the START UP screen and the INPUT_ INFORMATION when the INFORMATION on the SERVICE menu is chosen.

• This function is available only when the MY TEXT PASSWORD function is set to the OFF.

(1) Use the ▲/▼ buttons on the

SECURITY menu to select the MY TEXT WRITING and press the ► button. The MY TEXT WRITING dialog will be displayed.

(2) The current MY TEXT will be displayed

on the rst 3 lines. If not yet written, the lines will be blank. Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. To erase 1 character at one time, press the RESET button or press the ◄ and INPUT button at the same time. Also if you move the cursor to DELETE or ALL CLEAR on screen and press the ENTER or INPUT button, 1 character or all characters will be erased. The MY TEXT can be input up to 24 characters on each line.

(3) To change an already inserted

character, press the ▲/▼ button to move the cursor to one of the rst 3 lines, and use the ◄/► buttons to move the cursor on the character to be changed.

After pressing the ENTER or INPUT button, the character is selected. Then, follow the same procedure as described at the item (2) above.

(4) To nish entering text, move the cursor to the OK on screen and press

the ►, ENTER or INPUT button. To revert to the previous MY TEXT without saving changes, move the cursor to the CANCEL on screen and press the ◄, ENTER or INPUT button.

The MY TEXT WRITING function is available only when the MY TEXT

•

PASSWORD function is set to OFF. The CLONING operation under OPTION_SERVICE menu is not available if

ON is selected.

SECURITY menu

QM00611-1

Presentation toolsPresentation tools

Presentation tools

The projector has the following convenient tools that enable on-screen presentations easily and quickly:

- PC-LESS Presentation (

below)

- Drawing function Drawing function enables you to draw on the projector’s screen with USBmouse or tablets connected to the USB TYPE A ports. For details, refer to the manual for peripheral equipment.

- USB Display (88, 92)

PC-LESS Presentation

The PC-LESS Presentation reads image and audio data from the storage media inserted into the USB TYPE A port and displays the image in the following modes. The PC-LESS Presentation can be started by selecting the USB TYPE A port as the input source. This feature allows you to make your presentations without using your computer.

- Thumbnail mode (79)

- Full Screen mode (83)

- Slideshow mode (85)

[Supported storage media]

• USB memory (USB memory type, USB hard disk and USB card reader type)

NOTE

• USB readers (adapters) that have more than one USB slot may not

work (if the adapter is acknowledged as multiple devices connected).

• USB devices with security software may not work.

• Be careful when inserting or removing a USB device. (14, 81)

[Supported format]

• FAT12, FAT16 and FAT32

• NTFS is not supported.NOTE

QM00611-1

Presentation toolsPresentation tools

PC-LESS Presentation (continued)

[Supported le format and its extension]

• JPEG (.jpeg, .jpg) * Progressive is not supported.

• Bitmap (.bmp) * 16bit mode and compressed bitmap is not supported.

• PNG (.png) * Interlace PNG is not supported.

• GIF (.gif)

• Movie (.avi, .mov) *

Supported video format: Motion-JPEG

Supported audio format:

WAV (Linear PCM, Stereo 16bit),

IMA-ADPCM

NOTE

MC-CX301 : 1024 x 768 (Still)， 768 x 576 (Movie) MC-CW301 : 1280 x 800 (Still)， 768 x 576 (Movie)

• Files with a resolution larger than the following are not supported.

(* Some computers may not support 1280 x 800.)

• Files with a resolution smaller than 36 x 36 are not supported.

• Files with a resolution smaller than 100 x 100 may not be displayed.

• Movie images with a frame rate higher than 15 fps cannot be displayed.

• Movie images with a bit rate higher than 20 Mbps cannot be displayed.

• Some supported les may not be displayed.

• Only a frame appears when the content of image data cannot be displayed in the Thumbnail mode.

• Even with the le format and audio format combinations described above, playback of some les may fail.

Thumbnail mode

The Thumbnail mode displays the images stored in a USB storage device on the Thumbnail screen. Maximum 20 images are displayed in a screen. If you wish, you can jump into the Full Screen mode or Slideshow mode, after you select some images in the Thumbnail mode. The Thumbnail mode will be started as the primary function of the PC-LESS Presentation after selecting the USB TYPE A port as the input source.

Selected image

Thumbnail images

Thumbnail menu

QM00611-1

Presentation tools

PC-LESS Presentation (continued)

Operating by buttons or keys

You can control the images on the Thumbnail screen with the remote control, control panel or Web Remote Control. The following functions can be supported while the Thumbnail is displayed.

Button operation

The remote control

▲/▼/◄/► ▲/▼/◄/► [▲]/[▼]/[◄]/[►] Move cursor

PAGE UP PAGE DOWN

ENTER INPUT [ENTER]

Control panel

Web Remote Control

[PAGE UP] [PAGE DOWN]

Switches pages

• Displays the selected image on the Full Screen mode when a cursor is on a thumbnail image.

• Displays the setup menu (

below) for the selected image



when a cursor is on a thumbnail image number.

Functions

The setup menu for the selected image

Use the ◄/► cursor buttons to switch each setting or use the ► cursor button to execute the functions as follows.

Item Functions

RETURN Press the ► cursor button or ENTER to return to the Thumbnail screen.

START

STOP

SKIP

ROTATE

Switch to ON to set the selected image as the rst image in the Slideshow. This setting information will be saved in the “playlist.txt” le

87).

( Switch to ON to set the selected image as the last image in the

Slideshow. This setting information will be saved in the “playlist.txt” le (

87).

Switch to ON to skip the selected image in the Slideshow. This setting information will be saved in the “playlist.txt” le (

Press the ► cursor or ENTER button to rotate the selected still image 90 degrees clockwise. This setting information will be saved in the “playlist.txt” le (

87).

QM00611-1

Presentation tools

PC-LESS Presentation (continued)

Operating by the menu on the Thumbnail screen

You can also control the images by using the menu on the Thumbnail screen.

Item Functions

Moves to an upper folder.

SORT Allows you to sort les and folders as following.

RETURN

NAME UP Sorts in ascending order by le name. NAME DOWN Sorts in descending order by le name. DATE UP Sorts in ascending order by le date.

DATE DOWN Sorts in descending order.by le date. ▲/▼ Go to previous / next page. SLIDESHOW Congures and starts the Slideshow (

RETURN

PLAY Press the ► cursor button or ENTER to start the Slideshow.

START Sets the beginning number of the Slideshow.

STOP Sets the end number of the Slideshow.

INTERVAL

PLAY MODE Selects the Slideshow mode. INPUT Switches the input port. MENU Displays the menu.

REMOVE USB

Press the ► cursor button or ENTER to return to the Thumbnail screen.

85).



Press the ► cursor button or ENTER to return to the Thumbnail screen.

Sets the interval time for displaying still images during the Slideshow.

Be sure to use this function before removing USB storage device from the projector. After that, the projector will not recognize a USB storage device until you insert it again into the USB TYPE A input port.

Turns the sound on/off for les that contain audio data.

QM00611-1

Presentation toolsPresentation tools

PC-LESS Presentation (continued)

•

NOTE

These operations are not accessible while the projector OSD is displayed.

• The Thumbnail mode is able to display up to 20 les in one page.

• It is not possible to change the input port by using the INPUT button when the Thumbnail screen, Slideshow, or Full Screen is displayed.

• The image quality may deteriorate when playing back audio data included in a movie. If you want to give priority to the image quality, turn off the sound by setting ♪ to off.

• If one of the AUDIO IN ports is selected or is selected for USB TYPE A in AUDIO SOURCE of the AUDIO menu (50), ♪ cannot be operated.

• Some error icons will be displayed in the Thumbnail.

This le seems to be broken or not supported format.

A le that cannot be displayed on the thumbnail screen is indicated by a le format icon.

QM00611-1

Presentation tools

PC-LESS Presentation (continued)

Full Screen Mode

The Full Screen mode shows a full display image. To display in Full Screen mode, select an image in the Thumbnail screen. Then press the ENTER button on the remote control, the INPUT button on the control panel or click [ENTER] on the Web Remote Control.

Full screen display

Operations for still images

The following operations are enabled in the Full Screen mode while a still image is displayed.

Button operation

The remote control

▼ ► or

PAGE DOWN

▲ ◄ or

PAGE UP ENTER INPUT [ENTER] Displays Thumbnail.

Control panel

▼ or ►

▲ or ◄

Web Remote Control

[▼] [►] or [PAGE DOWN]

[▲] [◄] or [PAGE UP]

Shows the next le.

Shows the previous le.

Functions

QM00611-1

Presentation tools

PC-LESS Presentation (continued)

Operations for movie

A remote control icon and a progress bar are displayed when one of the cursor buttons, ENTER button or INPUT button on the remote control, control panel or Web Remote Control is pressed or clicked while a movie is playing in the Full Screen mode. The following operations are enabled while the remote control icon and progress bar are displayed.

Button operation

The remote control

▲ ▲ [▲]

► ► [►]

◄ ◄ [◄]

ENTER INPUT [ENTER] PAGE DOWN – [PAGE DOWN] PAGE UP – [PAGE UP]

NOTE

•

Control panel

These operations are not accessible while the projector OSD is displayed.

Web Remote Control

(Play) /

(FF) Fast-forward

(REW) Fast-rewind

(Stop), Displays Thumbnail. Shows the next le. Shows the previous le.

Functions

(Pause) toggle

• It is not possible to change the input port by using the INPUT button when the Thumbnail screen, Slideshow, or Full Screen is displayed.

QM00611-1

Presentation tools

PC-LESS Presentation (continued)

Slideshow mode

The Slideshow mode displays images in full screen and switches the images at intervals set in INTERVAL on the Thumbnail screen menu (80).

You can start this function from the Slideshow menu. To display the Slideshow menu, select the SLIDESHOW button in the Thumbnail mode and press the

ENTER button on the remote control, INPUT button on the control panel, or click [ENTER] on the Web Remote Control.

While the Slideshow is displayed, the following button operations are enabled when still images are displayed, and the same button operations in the Full Screen mode are enabled when movies are displayed.

Button operation

The remote control

ENTER INPUT [ENTER] Displays thumbnail

NOTE

• These operations are not accessible while the projector OSD is

Control panel

Web Remote Control

Functions

displayed.

• It is not possible to change the input port by using the INPUT button when the Thumbnail screen, Slideshow, or Full Screen is displayed.

• When the Slideshow mode is set to ONE TIME and the last le is a still image, the last slide of the presentation will remain displayed until the ENTER button on the remote control or Web Remote Control, or the INPUT button on the control panel is pressed.

QM00611-1

Presentation tools

PC-LESS Presentation (continued)

You can play the Slideshow at your desired conguration. Congure the Slideshow items in the Thumbnail.

1) RETURN :

Returns to the thumbnail mode.

2) PLAY : Play the Slideshow.

3) START :

Set the beginning number of the

Slideshow.

4) STOP : Set the end number of the Slideshow.

5) INTERVAL : Sets the interval time for displaying still images during the Slideshow. It is not recommend to set the interval time very short something like several seconds, because it may take more than several seconds to read and display an image le if it is stored in very deep layer directory or if so many les are stored in the same directory.

6) PLAY MODE : Select the Slideshow mode. ONE TIME : Play the Slideshow one time. ENDLESS : Play the Slideshow endless.

NOTE

• The settings of the Slideshow are saved to the “playlist.txt” le that is stored in the storage media. If the le is not existed, it is generated automatically.

• The settings for the START, STOP, INTERVAL, and PLAY MODE are saved to the Playlist.

• If the storage media is under the write protection or the “playlist.txt” is the read only type le, it is impossible to change the settings of the Slideshow.

QM00611-1

Presentation tools

PC-LESS Presentation (continued)

Playlist

The Playlist is a DOS format text le, which decides the order of displayed still image les in the Thumbnail or Slideshow. The playlist le name is “playlist.txt” and it can be edited on a computer. It is created in the folder that contains the selected image les when the PC-LESS Presentation is started or the Slideshow is congured.

[Example of “playlist.txt” les] START setting : STOP setting : INTERVAL setting : PLAY MODE setting :

img001.jpg: : : : img002.jpg:600: : : img003.jpg:700:rot1: : img004.jpg: : :SKIP: img005.jpg:1000:rot2:SKIP:

The “playlist.txt” le contains the following information. Each piece of information requires to be separated by “:”, and “:” at the end of

each line. 1st line: START, STOP, INTERVAL and PLAY MODE settings (86).

2nd line and after: le name, interval time, rotation setting and skip setting.

interval time: 100 (ms). rotation setting

skip setting: “SKIP” means that the image will not be displayed in the

It can be set from 0 to 999900 (ms) with an increment of

: “rot1” means a rotation at 90 degrees clockwise; “rot2”

and “rot3” increase another 90 degrees in order.

Slideshow.

•

NOTE

The maximum length in a line on the "playlist.txt" le is 255 characters

including linefeed. If any line exceeds the limit, the "playlist.txt" le becomes invalid.

•

Up to 999 les can be registered to the Playlist. However, if some folders exist in the same directory the limit number is decreased by the number of folders. Any les over the limit will not be shown in the Slideshow.

•

If the storage device is protected or does not have sufcient space, the “playlist.txt” le cannot be created.

• For the Slideshow settings, refer to the section Slideshow mode (85).

QM00611-1

Presentation tools

USB Display(Windows computer)

The projector can display images transferred from a computer via an USB cable (11).

Hardware and software requirement for computer

• OS: One of the following. Windows Windows® 8.1 Windows® 10

• CPU: Pentium 4 (2.8 GHz or higher)

• Graphic card: 16 bit, XGA or higher

• Memory: 512 MB or higher

• Hard disk space: 30 MB or higher

• USB Port

• USB cable : 1 piece

Starting USB Display

When you connect your computer to the USB TYPE B port on the projector using a USB cable, the projector will be recognized as a CD-ROM drive on your computer. Then, the software in the projector, “LiveViewerLiteForUSB.exe”, will run automatically and the application, “LiveViewer Lite for USB”, will be ready on your computer for the USB Display. The application, “LiveViewer Lite for USB”, will close automatically when the USB cable is unplugged. However, it may remain displayed at times.

NOTE

• If the software does not start automatically (this is typically because CD-ROM autorun is disabled on your OS), follow the instructions below. (1) Click on the [Start] button on the toolbar and select the “Run” (2) Enter F:\LiveViewerLiteForUSB.exe and then press the [OK]

If your CD-ROM drive is not drive F on your computer, you will need to replace F with the correct drive letter assigned to your CD-ROM drive.

• CD-ROM autorun is disabled while the screen saver is running.

• The image transmission from the computer is suspended while the passwordprotected screen saver is running. To resume the transmission, exit the screen saver.

•

If "Waiting for connection." remains displayed while the USB cable is connected,

remove the USB cable and reconnect after a while.

• Check our web site for the latest version of the software and its manual. (User's Manual (concise))

Follow the instructions that can be obtained at the site for updating.

(continued on next page)

QM00611-1

USB Display(Windows computer) (continued)

This application will appear in the Windows notication area once it starts. You can quit the application from your computer by selecting “Quit” on the menu.

Presentation tools

NOTE

• The “LiveViewer” (refer to the

Network Guide) and this application cannot

be used at the same time. If you connect your computer to the projector by using a USB cable while the “LiveViewer” is running, the following message will be displayed.

• Depending on the software installed on your computer, images on your computer cannot be transferred using “LiveViewer Lite for USB”.

• If any application software having the rewall function is installed into your computer, make the rwall function invalid with following the user's manual.

• Some security software may block image transmission. Please change the security software setting to allow the use of "LiveViewer Lite for USB".

• When the audio input from USB TYPE B is selected, if the sound level is still low even after raising the volume level in the projector to the maximum, check whether your computer outputs audio and raise the volume level accordingly.

• If the computer in use is equipped with HDMI port, the audio setting will be changed and sound interruption or noise may occur when the HDMI cable is connected or disconnected during USB Display. Restart USB Display for this case.

• Image distortion or sound interruption may occur when “LiveViewer” is connected to LAN (wireless or wired) during USB Display. The above decline in performance is noticeable especially when multiple computers are connected to “LiveViewer”.

QM00611-1

Presentation tools

USB Display(Windows computer) (continued)

Right-Click menu

The menu shown in the right will be displayed when you right-click the application icon in the Windows notication area.

Display : The Floating menu is displayed, and the icon disappears from the

Windows notication area.

Quit : The application is closed, and the icon disappears from the Windows

notication area.

NOTE

• If you wish to restart the application, you need to unplug the USB

cable and plug it again.

Floating menu

If you select “Display” on the Right-Click menu, the Floating menu shown in the right will appear on your computer screen.

 Start capture button

The transmission to the projector is started and the images will be displayed.

 Stop button

The image transmission is stopped.

 Hold button

The image on the projector’s screen is temporally frozen. The last image before the button is clicked is remained on the screen. You can revise the image data on your computer without showing it on the projector's screen.

 Option button

The Options window is displayed.

 Minimize button

The Floating menu is closed, and the icon reappears in the Windows notication area.

NOTE

• If you click the Start capture button and/or Stop button repeatedly,

images may not be displayed on the screen.

  

QM00611-1

Presentation tools

USB Display(Windows computer) (continued)

Options window

If you select the Option button on the Floating menu, the Options window is displayed.

Optimize Performance

The “LiveViewer Lite for USB” captures screenshots in JPEG data and sends them to the projector. The “LiveViewer Lite for USB” has two options that have different compression rate of JPEG data.

Transmission speed

Speed takes priority over Image quality. It makes JPEG compression rate higher. The screen on the projector is rewritten quicker because the transferred data is smaller, but the image quality is worse.

Image quality

Image quality takes priority over Speed. It makes JPEG compression rate lower. The screen on the projector is rewritten slower because the transferred data is larger, but the image quality is better.

Keep PC resolution

If you remove the check mark from the [Keep PC resolution] box, the screen resolution of your computer will be switched as follows, and the display speed may be faster. MC-CX301: 1024 x 768 (XGA) MC-CW301: 1280 x 800 (WXGA) If your computer does not support the display resolution specied above, a smaller resolution that is the largest among the resolutions that are supported by the computer will be selected.

Sound

Turns the sound on/off. The image quality may deteriorate when you play back audio data transferred together with the image data. To give priority to the image quality, turn off the sound by selecting the checkbox.

Display LiveViewer Lite for USB

If you want to display the "LiveViewer Lite for USB" application window on the screen, please check the box.

About

The version information of the “LiveViewer Lite for USB”.

NOTE

computer desktop screen may be changed.

• If one of the AUDIO IN ports is selected or is selected for USB TYPE B in AUDIO SOURCE of the AUDIO menu (50), audio sound operation in the Options window will be disabled.

• When the resolution is changed, the arrangement of icons on

QM00611-1

Presentation tools

USB Display(Mac computer)

The projector can display images transferred from a computer via an USB cable (11).

Hardware and software requirement for computer

• OS: Mac OS X Mac OS X® 10.7 Mac OS X® 10.8 Mac OS X® 10.9 Mac OS X® 10.10 Mac OS X® 10.11 macOS® 10.12 This application is not compatible with Power PC.

• Graphic card: 16 bit, XGA or higher

• Memory: 512 MB or higher

• Hard disk space: 30 MB or higher

Starting USB Display

When you connect your computer to the USB TYPE B port on the projector using a USB cable, the projector will be recognized as a CD-ROM drive on your computer. Double click the CD-ROM, then double click "LiveViewerLiteForUSB_MacOS.app.". The application, “LiveViewer Lite for USB”, will close automatically when the USB cable is unplugged. However, it may remain displayed at times.

10.6

NOTE

• The image transmission from the computer is suspended while the password-protected screen saver is running. To resume the transmission, exit the screen saver.

•

If "Waiting for connection." remains displayed while the USB cable is connected,

remove the USB cable and reconnect after a while.

• Check our web site for the latest version of the software and its manual. (User's Manual (concise))

Follow the instructions that can be obtained at the site for updating.

(continued on next page)

QM00611-1

USB Display(Mac computer) (continued)

Presentation tools

NOTE

• The “LiveViewer” (refer to the Network Guide) and this application cannot be used

at the same time. If you connect your computer to the projector by using a USB cable while the “LiveViewer” is running, the following message will be displayed.

• Depending on the software installed on your computer, images on your computer cannot be transferred using “LiveViewer Lite for USB”.

• If any application software having the rewall function is installed into your computer, make the rwall function invalid with following the user's manual.

• Some security software may block image transmission. Please change the security software setting to allow the use of "LiveViewer Lite for USB".

QM00611-1

Presentation tools

USB Display(Mac computer) (continued)







If you select “Display” on the Right-Click menu, the Floating menu shown in the right will appear on your computer screen.

 Start capture button

The transmission to the projector is started and the images will be displayed.

 Stop button

The image transmission is stopped.

 Hold button

 Option button

The Options window is displayed.

 Minimize button

The Floating menu is closed, and the icon reappears in the Windows notication area.

 Exit button

The Floating menu is closed.

NOTE

• If you click the Start capture button and/or Stop button repeatedly, images may not be displayed on the screen.

QM00611-1

Presentation tools

USB Display(Mac computer) (continued)

Options window

If you select the Option button on the Floating menu, the Options window is displayed.

Optimize Performance

Transmission speed

Image quality

Image quality takes priority over Speed. It makes JPEG compression rate lower. The screen on the projector is rewritten slower because the transferred data is larger, but the image quality is better.

Keep PC resolution

Sound

About

The version information of the “LiveViewer Lite for USB”.

NOTE

• When the resolution is changed, the arrangement of icons on computer desktop screen may be changed.

• If one of the AUDIO IN ports is selected or is selected for USB TYPE B in AUDIO SOURCE of the AUDIO menu (50), audio sound operation in the Options window will be disabled.

QM00611-1

Maintenance

Replacing the lamp

A lamp has nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, make contact with your dealer and tell the lamp type number.

Type number : DT01511

Replacing the lamp

Turn the projector off, and unplug the power cord.

Allow the projector to cool for at least 45 minutes. Prepare a new lamp. If the projector is mounted on

a ceiling, or if the lamp has broken, also ask the dealer to replace the lamp.

In case of replacement by yourself, follow the following procedure.

Loosen the screw (marked by arrow) of the lamp

cover and then slide and lift the lamp cover to the side to remove it.

Loosen the 2 screws (marked by arrow) of the lamp,

and slowly pick up the lamp by the handle. Never loosen any other screws.

Insert the new lamp, and retighten rmly the 2

screws of the lamp that are loosened in the previous process to lock it in place.

While putting the interlocking parts of the lamp cover

and the projector together, slide the lamp cover back in place. Then rmly fasten the screw of the lamp cover.

Turn the projector on and reset the lamp time using

the LAMP TIME item in the SETUP menu.

(1) Press the MENU button to display a menu. (2) Point at the ADVANCED MENU in the menu using

the ▼/▲ button, then press the ► button.

(3) Point at the SETUP in the left column of the menu

using the ▼/▲button, then press the ► button.

(4)

Point at the LAMP TIME using the ▼/▲ button, then press the ► button. A dialog will appear.

(5)

Press the ► button to select “OK” on the dialog. It performs resetting the lamp time.

CAUTION

is taken out.

►Do not touch any inner space of the projector, while the lamp

lamp cover

Handle

NOTE

for a suitable indication about the lamp.

• Please reset the lamp time only when you have replaced the lamp,

QM00611-1

Maintenance

Replacing the lamp (continued)

Lamp warning

HIGH VOLTAGE

►

WARNING

The projector uses a high-pressure mercury glass lamp. The lamp

HIGH TEMPERATURE

can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, if the bulb bursts, it is possible for shards of glass to y into the lamp housing, and for gas containing mercury and dust containing ne particles of glass to escape from the projector’s vent holes. ►About disposal of a lamp: This product contains a mercury lamp; do not put it in a trash. Dispose of it in accordance with environmental laws.

• For lamp recycling, go to www.lamprecycle.org (in the US).

• For product disposal, consult your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada). For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

•

Disconnect

the plug from the

power

outlet

If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to inhale the gas or ne particles that come out from the projector's vent holes, and not to get them into your eyes or mouth.

• Before replacing the lamp, turn the projector off and unplug the power cord, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

• Never unscrew except the appointed (marked by an arrow) screws.

• Do not open the lamp cover while the projector is mounted on a wall or ceiling. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

• Use only the lamp of the specified type. Use of a lamp that does not meet the lamp specications for this model could cause a re, damage or shorten the life of this product.

• If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, consult your local dealer or a service representative.

•

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

•

Using the lamp for long periods of time, could cause it dark, not to light up or to burst. When the pictures appear dark, or when the color tone is poor, please replace the lamp as soon as possible. Do not use old (used) lamps; this is a cause of breakage.

HIGH PRESSURE

QM00611-1

Maintenance

Cleaning and replacing the air lter

The air lter unit of this projector consists of a lter cover, two kinds of lters, and a lter frame. The new double large lters system is expected to function longer. However, please check and clean it periodically to keep ventilation needed for normal operation of the projector. When the indicators or a message prompts you to clean the air lter, comply with it as soon as possible. Replace the lters when they are damaged or too soiled. To prepare new lters, make contact with your dealer and tell the following type number.

Type number : UX37191 (Filter set)

When you replace the lamp, please replace the air lter. An air lter of specied type will come together with a replacement lamp for this projector.

Turn the projector off, and unplug the power cord.

Allow the projector to sufciently cool down.

Use a vacuum cleaner on and around the lter cover.

Slide the lter unit upward to take it off from the

projector.

Use a vacuum cleaner for the lter vent of the

projector.

Take the ne meshed lter out while holding the

lter cover. It is recommended to leave the coarse meshed lter in the lter cover as it is.

Use a vacuum cleaner on both sides of the ne

meshed lter while holding it so it will not be sucked in. Use a vacuum cleaner for the inside of the lter cover to clean up the coarse meshed lter. If the lters are damaged or heavily soiled, replace them with new ones.

Put the ne meshed lter on the coarse meshed one,

turning its plastic band side up.

Put the lter unit back into the projector.

Filter cover

Filter unit

Filter (ne meshed)

Filter cover

Filter (coarse meshed)

Plastic band

Intake vent

(continued on next page)

QM00611-1

Maintenance

Cleaning and replacing the air lter (continued)

Turn the projector on and reset the lter time using the FILTER TIME item in

the EASY MENU. (1) Press the MENU button to display a menu.

(2) Point at the FILTER TIME using the ▼/▲ button, then press the ► button.

A dialog will appear.

(3) Press the ► button to select “OK” on the dialog. It performs resetting the

lter time.

WARNING

is not plugged in, then allow the projector to cool sufciently. Taking care of the air lter in a high temperature state of the projector could cause an electric shock, a burn or malfunction to the projector. ►Use only the air lter of the specied type. Do not use the projector without the air lter or the lter cover. It could result in a re or malfunction to the projector. ►Clean the air lter periodically. If the air lter becomes clogged by dust or the like, internal temperatures rise and could cause a re, a burn or malfunction to the projector.

NOTE

• When you replace the projection lamp, please replace the air lter. An air lter of specied type will come together with a replacement lamp for this projector.

• Please reset the lter time only when you have cleaned or replaced the air lter, for a suitable indication about the air lter.

• The projector may display the message such as “CHECK THE AIR FLOW” or turn off the projector, to prevent the internal heat level rising.

• Please replace the air lter when it is damaged or heavily soiled.

►Before taking care of the air lter, make sure the power cable

QM00611-1

Maintenance

Installing or replacing the internal clock battery

This product has an internal clock. When you use the function that requires the internal clock ("Event Scheduling" in the Network Guide), install a new battery. If the internal clock starts to malfunction, try to replace the battery. Use the following type of battery, and follow the steps below. MAXELL, Part No. CR2032 or CR2032H

Turn the projector off, and unplug the power cord.

Allow the projector to cool sufciently.

After making sure that the projector has cooled

adequately, slowly turn over the projector, so that the bottom is facing. Turn the battery cover fully in the direction indicated

“OPEN” using a coin or the like, and pick the cover up to remove it.

Pry up the old battery using a athead screwdriver

or the like to take it out. Do not use any metal tools. While prying it up, put a nger lightly on the battery since it may pop out of the holder.

Install a new battery in place.

Slide the battery in under the plastic claw, and push it into the holder until it clicks.

Replace the battery cover in place, then turn it in

the direction indicated “CLOSE” using such as coins, to x.

WARNING ►Always handle the batteries with care and use them only as directed. Battery may explode if mistreated. Do not recharge, disassemble or dispose of in re. And also improper use may result in cracking or leakage, which could result in re, injury and/or pollution of the surrounding environment.

・ Be sure to use only the batteries specied. ・ Make sure the plus and minus terminals are correctly aligned when loading a battery. ・ Keep a battery away from children and pets. If swallowed consult a physician

immediately for emergency treatment.

・ Do not short circuit or solder a battery. ・ Do not allow a battery in a re or water. Keep batteries in a dark, cool and dry place. ・ If you observe battery leakage, wipe out the leakage and then replace a battery. If the

leakage adheres to your body or clothes, rinse well with water immediately.

・ Obey the local laws on disposing a battery.

90°

OPEN

Battery Cover

90°

OPEN

NOTE

• The internal battery is required to be replaced when the time is off

soon after setting date and time.

100

QM00611-1

Maxell MC-CW301 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual