How it Works
Maxdata
Loading...
200I M7
user manual
27 pgs629.41 Kb0

Maxdata 200I M7 user manual

MAXDATA PLATINUM 200 I M7
User’s Manual
2 3MAXDATA PLATINUM 200 I M7Contents
Contents
1 Setting up the System 5
Safety Information ...................................................................................................................................5
Powering up the System .........................................................................................................................7
2 Board Features 9
Connector and Header Locations ..........................................................................................................10
Configuration Jumpers ..........................................................................................................................11
Back Panel Connectors .........................................................................................................................12
Hardware Requirements .......................................................................................................................13
3 Hardware Installations and Upgrades 15
Before You Begin ..................................................................................................................................15
Installing and Removing Memory ..........................................................................................................15
Replacing the Backup Battery ...............................................................................................................17
4 Server Utilities 19
Using the BIOS Setup Utility .................................................................................................................19
Clearing the CMOS ...............................................................................................................................21
Configuring the System for embedded Serial ATA RAID ......................................................................22
5 Rack Installation 23
Parts List ..............................................................................................................................................23
Installation .............................................................................................................................................24
6 Regulatory and Compliance Information 27
Product Regulatory Compliance ............................................................................................................27
Electromagnetic Compatibility Notices .................................................................................................27
Figures
1. PLATINUM 200 I Controls ................................................................................................................. 7
2. Board Connector and Component Locations ..................................................................................10
3. Configuration Jumpers ....................................................................................................................11
4. Back panel Connectors ...................................................................................................................12
5. Installing DIMMs .............................................................................................................................15
6. Removing the Battery .....................................................................................................................18
7. Clearing the CMOS .........................................................................................................................21
Tables
1. Feature Summary .............................................................................................................................. 9
2. Board Connectors and Components ...............................................................................................10
3. Configuration Jumpers ....................................................................................................................11
4. Back panel Connectors ...................................................................................................................12
5. NIC LEDs ......................................................................................................................................... 12
6. Keyboard Commands ......................................................................................................................20
7. Product Certification Markings ........................................................................................................27
4 MFMAXDATA PLATINUM 200 I M7Contents
1 Setting up the System
Safety Information
Server Position
Please take note of the following criteria for creating a practical and safe workplace when setting up your computer:
!
CAUTION
The system can be used anywhere the temperature is suitable for people. However, rooms with humidity over 70%, and dusty or dirty areas are not appropriate. In addition, do not expose the server to any temperatures over +30°C or under +10°C.
!
CAUTION
For proper cooling and airflow, operate the system only with the chassis covers installed.
!
CAUTION
Make sure that the cables connecting the server to peripheral devices are not tight.
!
CAUTION
Make sure that all power and connection cables are positioned so that they are not trip hazards.
!
CAUTION
When you save data to your server‘s hard disks or to a floppy disk, they are stored as magnetic information on the media. Make sure that they are not damaged by magnetic or electromagnetic fields.
!
CAUTION
Because the electronics in your computer can be damaged by jarring, no mechanical devices should be placed on the same surface as the server. This is especially important for impact printers whose vibrations could damage the hard disk.
!
CAUTION
Hazardous conditions, devices and cables: Hazardous electrical conditions may be present on power, telephone, and communication cables. Turn off the server and disconnect the power cord, telecommunications systems, networks, and modems attached to the server before opening it. Otherwise, personal injury or equipment damage can result.
!
CAUTION
Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives, boards, and other parts. We recommend that you perform all procedures in chapter 3 only at an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis ground - any unpainted metal surface - on your server when handling parts.
!
ATTENTION
In order to fully separate the server from current, the power cord must be removed from the wall outlet.
!
ATTENTION
To ensure stability, the floor stands must be turned outwards (pedestal version only).
System Access Warnings
!
CAUTION
To avoid personal injury or property damage, the following safety instructions apply whenever accessing the inside of the product:
• Turn off all peripheral devices connected to this product.
• Turn off the system by pressing the power button to off.
• Disconnect the AC power by unplugging all AC power cords from the system or wall outlet.
• Disconnect all cables and telecommunication lines that are connected to the system.
• Retain all screws or other fasteners when removing access cover(s). Upon completion of accessing inside the product, refasten access cover with original screws or fasteners.
• Do not access the inside of the power supply. There are no serviceable parts in the power supply. Return to manufacturer for servicing.
• Power down the server and disconnect all power cords before adding or replacing any non hot­plug component.
• When replacing a hot-plug power supply, unplug the power cord to the power supply being replaced before removing the power supply from the server.
!
CAUTION
If the server has been running, any installed processor(s) and heat sink(s) may be hot. Unless you are adding or removing a hot-plug component, allow the system to cool before opening the covers. To avoid the possibility of coming into contact with hot component(s) during a hotplug installation, be careful when removing or installing the hot-plug component(s).
!
CAUTION
To avoid injury do not contact moving fan blades. If your system is supplied with a guard over the fan, do not operate the system without the fan guard in place.
Rack Mount Warnings
The equipment rack must be anchored to an unmovable support to prevent it from tipping when a server or piece of equipment is extended from it. The equipment rack must be installed according to the rack manufacturer‘s instructions.
Install equipment in the rack from the bottom up, with the heaviest equipment at the bottom of the rack.
Extend only one piece of equipment from the rack at a time.
You are responsible for installing a main power disconnect for the entire rack unit. This main disconnect must be readily accessible, and it must be labeled as controlling power to the entire unit, not just to the server(s).
To avoid risk of potential electric shock, a proper safety ground must be implemented for the rack and each piece of equipment installed in it.
6 7MAXDATA PLATINUM 200 I M7Setting up the System
Powering up the System
G
H
I
A
B
C
D
E
F
At the front of the case, you can find the neccessary controls like power button, reset button and the HDD LEDs. Press the power button one time briefly in order to boot the server.
Figure 1. PLATINUM 200 I Controls
A. Power LED E. Fan Warning LED
B.
HDD LED F. Front USB ports
C. NIC2 LED G. Power switch
(not used in this system) H. Reset switch
D. NIC1 LED I. Disable Fan Warning
8
2 Board Features
This chapter briefly describes the main features of the mainboard.
Table 1 summarizes the major features of the board.
Table 1. Feature Summary
Feature Description
Processor • Support for one Intel
Intel® Pentium® D, Pentium® 4 or Celeron® D processor
• Supports Intel® Dual Core Architecture
• Supports Intel® Hyper-Threading Technology
• Supports Intel
Memory • 4 DIMM sockets supporting 533/667 MHz ECC or non-ECC
unbuffered stacked DDR2 DIMMs
• Data bandwidth per channel of 4.2 GB/s or 8.4 GB/s in dual channel when using DDR2 667 MHz
• Support for up to two DDR2 channels for a total of 4 DIMMs (2 DIMMs / Channel) providing up to 8 GB max memory capacity
Chipset Intel® 3000 chipset, consisting of:
• Intel® 3000 MCH Memory Controller Hub
®
ICH7R I/O Controller Hub
• Intel
I/O Control
Super I/O: SMsC SCH5027
External connections:
• Stacked PS2 Keyboard/Mouse connections
• DB9 Serial A port
• One RJ45 NIC connector for 10/100/1000 Mbps connections
• Two USB 2.0 ports
Internal connections:
• One USB port header which supports two USB 2.0 ports
• One DH10 Serial B header
• Four SATA connectors with integrated RAID 0/1/10 support
• One ATA-100 connector
• ATX-compliant 24-pin control panel header
Video On-board ATI ES1000 video controller with 16 MB external video
memory
Expansion Capabilities • Two full length 32 bit / 33 MHz, 3.3 V Universal PCI connectors
• One x8 PCI Express connector
• One physical x8 PCI Express connector (operating at x4 lane speed)
Hard drive • Ultra ATA100 support: One IDE channel capable of supporting up to
two drives.
• SATA support: Four independent SATA ports support data transfer rates up to 3.0 Gbit/s per port
Fans Support for up to four system fans and one processor fan
®
Xeon® Processor 3000 Sequence,
®
Extended Memory System 64 Technology (EM64T)
System Management
Intel® System Management Software
Loading...
+ 18 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use