Mattel FLAG FINISH LIGHTNING McQUEEN Instructions Manual
3
+
FLAG FINISH
LIGHTNING McQUEEN
INSTRUCTIONS
CONTENTS
CAUTION:
away from the wheels.
Keep these instructions for future reference as they contain important information.
IMPORTANT: Please read all instructions before operating your vehicle.
To prevent entanglement, keep all hair
INSTRUCTION SHEET
SPECIFICATIONS
Toy:
Toy No.:
0970G1-1101036848_DOM
Part No.:
Trim Size:
Folded Size:
Type of Fold:
# colors:
Colors:
Paper Stock:
Paper Weight:
EDM No.:
DHD71
3
1
5
Cover
FEATURES
O
I
1
2
FLAG TRANSMITTER
VEHICLE
1
POWER SWITCH
= OFF
= ON
2
BATTERY COVER
3
MODE SWITCH
= OFF
= DRAG & DRIFT
= RACE LAPS
= VICTORY DANCE
4
BATTERY COVER
4
3
15 6
You can use the flag transmitter to play with Lightning McQueen in the following modes:
DRAG & DRIFT
RACE LAPS
VICTORY DANCE
IMPORTANT:
• Always start with the vehicle and transmitter powered OFF, and within 6 inches from
each other.
• Always turn ON the vehicle and put it on the floor before turning ON the transmitter.
• Always turn OFF the transmitter before the vehicle.
NOTE:
• This product is not recommended for use on loose dirt or wet surfaces.
• To conserve battery life, Lightning McQueen goes to sleep when left idle. To wake him
up, switch the vehicle and transmitter OFF and then ON again.
3
+
2 3 4
Protect the environment by not disposing of this product with
household waste ( 2012/19/EU ). Check your local authority for
recycling advice and facilities.
BATTERY INSTALLATION
1
LET’S PLAY!
2
VEHICLE & FLAG TRANSMITTER
Vehicle requires 6 AA (LR06) alkaline batteries, not included.
Transmitter requires 2 AAA (LR03) alkaline batteries, not included.
For longer life, use alkaline batteries. Dispose of batteries safely.
1. Unscrew the battery cover with a Phillips
head screwdriver (not included).
2. Install 6 AA (LR06) alkaline batteries, with
polarity (+/-) as shown inside the battery
compartment.
3. Replace battery cover
and tighten screws.
VEHICLE
FLAG TRANSMITTER
1. Unscrew the battery cover with a Phillips
head screwdriver (not included).
2. Install 2 AAA (LR03) alkaline batteries, with
polarity (+/-) as shown inside the battery
compartment.
3. Replace battery cover and tighten screw.
NOTE: When exposed to an
electrostatic source, the toy
may malfunction. To resume
normal operation, remove
and re-install the batteries.
This should reset the toy
and let you resume normal
operation.
BATTERY SAFETY INFORMATION
In exceptional circumstances batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the product before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
• Do not mix old and new batteries.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the product.
• The supply terminals are not to be short-circuited.
• Dispose of battery(ies) safely.
• Do not dispose of this product in a fire. The batteries inside may explode or leak.
1
1
2
3
DRAG & DRIFT
Turn ON the vehicle and slide the MODE SWITCH on the flag to . When you hear
“Time for a drag race! Drop the flag!” wave the flag downward, then hold it still, to see
Lightning McQueen race forward. When you want Lightning McQueen to stop, wave the
flag downward again and he drifts to a halt.
AA
x6
(NOT INCLUDED)
AAA
x2
(NOT INCLUDED)
Loading...