Matsui mur1108ww, mur1108wwe Instruction Manual
INSTRUCTION MANUAL
DOMESTIC USE
UNDER COUNTER FRIDGE
MUR1108WW
MUR1108WWE
Satety Warnings Operation Cleaning and
Maintenance
SpecificationBefore Use
GB-2
Safety
WARNING!
It is hazardous for anyone other than authorised service personnel to carry out
servicing or repairs which involves the removal of covers.
To avoid the risk of an electric shock do not attempt to repair this appliance
yourself.
If the supply cord is damaged it must be replaced by the manufacturer, its
service agent, or similarly qualied persons in order to avoid a hazard.
This appliance is not intended for use by persons (including children) with
reduced sensory or mental capabilities, or lack of experience and knowledge
unless they have been given supervision or instruction concerning the use
of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
Disposal
Old appliances still have some residual value. An environmentally friendly
method of disposal will ensure that valuable raw materials can be recovered
and used again. The refrigerant used in your fridge and insulation materials
require special disposal procedures. Ensure that none of the pipes on the back
of the fridge are damaged prior to disposal. Up to date information concerning
options for disposing of your old appliance and packaging from the new one
can be obtained from your local council ofce.
Locks
If your appliance is tted with a lock, to prevent children being entrapped keep
the key out of the reach and not in the vicinity of the appliance. If disposing of
an old appliance break off any old locks or latches as a safeguard.
Satety WarningsOperationCleaning and
Maintenance
Specification Before Use
GB-3
Getting to know your product
Before Use
Please read these instructions carefully before using your new Matsui fridge.
The fridge is for indoor and domestic use only.
Bottle StorageLeveling Feet
(behind kick strip)
Salad Bin
Adjustable
Shelf
Glass Shelf
Internal Light
and
Thermostat Control Dial
Freezer Compartment
Ice Tray
Satety Warnings Operation Cleaning and
Maintenance
SpecificationBefore Use
GB-4
Installation
Location
When selecting a position for your fridge, you should make sure the oor is
at and rm, and the room is well ventilated with an average room tempera-
ture of between 16ºC and 32ºC. Locate the fridge away from direct sunlight
and source of heat (stove, heater, radiator, etc.). Direct sunlight may affect
the acrylic coating and heat sources may increase electrical consumption.
Extreme cold ambient temperatures may also cause the fridge not to perform
properly.
This unit is not designed for use in a garage or any other outside installation.
Avoid locating the fridge in moist areas. It must therefore be installed so that
the fridge has at least 10cm (2.5”) of free space and the sides have 2cm (3/4”).
The door of the fridge can either open to the right or to the left, depending on
whichever suits you. See page 5 if you want to reverse the door swing. Do not
drape your fridge with any covering.
Moving the fridge
Position your fridge in front of its nal operating position and gentle slide the
fridge into position.
A minimum of two persons must be used to move the fridge.
Leveling the Under Counter Fridge
Remove the packaging support from the base of the fridge
and replace with the 2 leveling feet.
Make sure the fridge is level. Use the leveling feet at the
front. If the fridge is not level, the door and magnetic seal
alignments will be affected.
Cleaning before use
Wipe the inside of the fridge with a weak solution of bicarbonate soda. Then
rinse with warm water using a damp sponge or cloth. Wash the baskets and
shelves in warm soapy water and dry completely before replacing in the fridge.
The external parts of the fridge can be cleaned with wax polish. If you require
more information, refer to Cleaning on page 12.
Before plugging in YOU MUST
Check that you have a socket which is compatible with the plug supplied with
the fridge. If not, please consult a qualied technician for assistance.
Before switching on!
DO NOT SWITCH ON UNTIL TWO HOURS AFTER MOVING THE
FRIDGE.
The coolant uid needs time to settle.
Satety WarningsOperationCleaning and
Maintenance
Specification Before Use
GB-5
Ensure the fridge is unplugged and empty.•
Adjust the two leveling feet to their highest •
position.
We recommend you have someone to •
assist you.
NOTE: Take the door off it is necessary to tilt the fridge backward. You
should rest the fridge on something solid and place something under
the rollers so that it will not slip during the door change process.
DO NOT lay the fridge completely at as this may damage the coolant system.
Reverse the door swing
Tools required
Phillips style screwdriver•
Flat bladed screwdriver•
A spanner may be required •
to loosen the bolts n.
1. Remove the screws and hinge
bracket from the base.
2. Slide the door down and remove
away from the fridge.
3. Remove the top hinge pin and
spring inside the door and ret on
the opposite side.
4. Slide the fridge door back on
to the top hinge. Screw the
bottom hinge into place on the
new side.
5. Check that the door is aligned horizontally and vertically and that the seals are
closed on all sides before nally tightening the bottom hinge. Re-adjust the
leveling feet.
Loading...