Matrix Fitness U7xi, U5x, U7xe, U3xe, U3x User Manual
U7xi
U7xe
U5x
U3xe
U3x
R7xi
R7xe
R5x
R3xe
R3x
H7xi
H7xe
H5x
H3xe
H3x
2
3
IMPORTANT PRECAUTIONS
SAVE THESE INSTRUCTIONS
• When using Matrix Cycles, basic precautions should always be followed, including the following: Read all instructions before using this equipment. It is
the responsibility of the owner to ensure that all users of this equipment are adequately informed of all warnings and precautions.
• This equipment is intended for commercial use. To ensure your safety and protect the equipment, read all instructions before operating.
DANGER!
TO REDUCE THE RISK OF ELECTRICAL SHOCK:
• Always unplug the equipment from the electrical outlet, before cleaning, performing maintenance and putting on or taking off parts.
• Use this exercise cycle for its intended purpose as
described in this manual. Do not use attachments that
have not been recommended by the manufacturer.
• Never operate the exercise cycle if it is not working properly,
or if it has been damaged. Contact Customer Tech Support
or the authorized dealers for examination and repair.
• Do not use the exercise cycle without proper footwear.
NEVER operate the exercise cycle with bare feet.
• Do not wear any clothing that might catch on
any moving parts of this exercise cycle.
• Keep hands and feet clear at all times from moving parts
to avoid injury. Never turn the pedal cranks by hand.
• Do not dismount the exercise cycle until
the pedals are at a complete STOP.
• Do not attempt to ride the exercise
cycle in a standing position.
• Do not insert any object, hands or feet into any openings,
or expose hands, arms or feet to the drive mechanism
or other potentially moving part of the exercise cycle.
• Do not use any equipment that is damaged or has worn
or broken parts. Use only replacement parts supplied
by Customer Tech Support or the authorized dealers.
• Do not operate where aerosol (spray) products are
being used or when oxygen is being administered.
• Close supervision is necessary when used near children.
• This equipment is not intended for use by persons with
reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
equipment by a person responsible for their safety.
• Ensure that adjustment levers (seat and handlebar
fore-and-aft) are properly secured and do not
interfere with range of motion during exercise.
• Incorrect or excessive exercise may result in serious
injury or death. If you experience any kind of pain,
including but not limited to chest pains, nausea, dizziness,
or shortness of breath, stop exercising immediately
and consult your physician before continuing.
• Do not jump on the unit.
• At no time should more than one person
be on unit while in operation.
• This unit should not be used by persons weighing more
than specied in the OWNER’S MANUAL SPECIFICATIONS
SECTION. Failure to comply will void the warranty.
• Keep power cord away from heated surfaces. Do not carry
this unit by its supply cord or use the cord as a handle.
• Do not use other attachments that are not recommended
by the manufacturer. Attachments may cause injury.
• Use the unit only as described in the
unit guide and owner’s manual.
CAUTION!
CONSULT A PHYSICIAN BEFORE USING THIS EQUIPMENT. READ OWNER’S MANUAL BEFORE USE.
• It is essential that this equipment is used only indoors, in a climate controlled room. If this equipment has been exposed to colder temperatures or high moisture
climates, it is strongly recommended that the equipment is warmed up to room temperature and allowed time to dry out before rst time use.
WARNING!
TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:
• Disconnect all power before servicing or moving
the equipment. To clean, wipe surfaces down
with soap and slightly damp cloth only; never
use solvents. (See MAINTENANCE)
• At NO time should pets or children under the
age of 14 be closer to the unit than 10 feet.
• At NO time should children under the age of 14 use the unit.
• Children over the age of 14 should not use
the unit without adult supervision.
• Never operate the unit if it has a damaged cord or
plug, if it is not working properly, if it has been dropped
or damaged, or immersed in water. Return the unit
to a service center for examination and repair.
• To disconnect, turn all controls to the off
position, then remove plug from outlet.
• Do not remove the console covers unless instructed
by Customer Tech Support. Service should only
be done by an authorized service technician.
• Heart rate monitoring systems may be inaccurate.
4
for power. These cycles can be daisy-chained
together with up to 4 units per 15 A circuit. This
outlet should be a NEMA 6-20R and have the
same conguration as the plug. No adapter
should be used with this product. Matrix
daisy-chain cord adapters are sold separately.
GROUNDING INSTRUCTIONS
The unit must be grounded if connected to a
power supply source. If it should malfunction
or breakdown, grounding provides a path of
least resistance for electric current to reduce
the risk of electric shock. The unit is equipped
with a cord having an equipment-grounding
conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is
properly installed and grounded in accordance
with all local codes and ordinances. If the user
does not follow these grounding instructions,
the user could void the Matrix limited warranty.
ADDITIONAL ELECTRICAL INFO
In addition to the dedicated circuit requirement, the proper
gauge wire must be used from the circuit breaker box, to each
outlet that will have the maximum number of units running
off of it. If the distance from the circuit breaker box to each
outlet, is 100 ft (30.5 m) or less, then 12 gauge wire should be
used. For distances greater than 100 ft (30.5 m) from the circuit
breaker box to the outlet, a 10 gauge wire should be used.
ENERGY SAVING / LOW-POWER MODE
All units are congured with the ability to enter into an energy
saving / low-power mode when the unit has not been in use
for a specied period of time. Additional time may be required
to fully reactivate this unit once it has entered the low-power
mode. This energy saving feature may be enabled or disabled
from within the ‘Manager Mode’ or ‘Engineering Mode.’
ADD-ON PCTV (3X AND 5X)
A 15 A or 20 A “Dedicated Circuit” with a non-looped (isolated)
neutral/ground is required. Each PCTV requires at least 1.2 A of
current. No more than 12 PCTVs should be used for each 15 A
circuit and no more than 16 PCTVs should be used for each 20
A circuit. The power outlet should have the same conguration
as the plug. No adapter should be used with this product. An
DEDICATED CIRCUIT AND ELECTRICAL INFO
A “Dedicated Circuit” means that each outlet you plug into should
not have anything else running on that same circuit. The easiest
way to verify this is to locate the main circuit breaker box, and turn
off the breaker(s) one at a time. Once a breaker has been turned
off, the only thing that should not have power to it are the units
in question. No lamps, vending machines, fans, sound systems, or
any other item should lose power when you perform this test.
Non-looped (isolated) neutral/grounding means that each circuit
must have an individual neutral/ground connection coming from
it, and terminating at an approved earth ground. You cannot
“jumper” a single neutral/ground from one circuit to the next.
ELECTRICAL REQUIREMENTS
For your safety and to ensure good unit performance, the ground
on this circuit must be non-looped (isolated). Please refer to
NEC article 210-21 and 210-23. Any alterations to the standard
power cord provided could void all warranties of this product.
The 3x, 3xe, 5x, 7xe and 7xi cycles are designed to be self-powered
and do not require an external power supply source to operate.
Without an external power supply, the console’s start-up time
may be delayed. Add-on TV’s and other console accessories
will increase the time needed for start-up. An external power
supply will ensure power is provided to the console at all times
and is recommended when add-on accessories are used.
For units with an integrated TV (like the 3xe, 7xe and 7xi), the
TV power requirements are included in the unit. An RG6 quad
shield coaxial cable with ‘F Type’ compression ttings on each
end will need to be connected to the cardio unit and the video
source. Additional power requirements are not needed for
the add-on digital TV (3x and 5x). For units with an add-on
PCTV (3x and 5x), the TV power requirements are separate.
NOTE: All units with Virtual Active™ must be powered.
110 V UNITS
All Matrix 110 V cycles require the use of a 100-125 V, 60 Hz and a 15
A “Dedicated Circuit”, with a non-looped (isolated) neutral/ground
for power. These cycles can be daisy-chained together with up to 4
units per 15 A circuit. This outlet should be a NEMA 5-15R and have
the same conguration as the plug. No adapter should be used with
this product. Matrix daisy-chain cord adapters are sold separately.
220 V UNITS
All Matrix 220 V cycles require the use of a 216-250 V, 50 Hz and a 15
A “Dedicated Circuit”, with a non-looped (isolated) neutral/ground
RG6 coaxial cable with ‘F Type’ compression
ttings will need to be connected between the
video source and each add-on PCTV unit.
ADD-ON DIGITAL TV (3X AND 5X)
Additional power requirements are not needed
for the add-on digital TV. An RG6 coaxial
cable with ‘F Type’ compression ttings will
need to be connected between the video
source and each add-on digital TV unit.
WARNING!
• Connect this exercise product to a
properly grounded outlet only.
• Never operate product with a damaged cord
or plug even if it is working properly. Never
operate any product if it appears damaged, or
has been immersed in water. Contact Customer
Tech Support for replacement or repair.
Failure to follow these specications
can cause damage to your product
and can void the warranty:
• All video and power outlets must be functional
the day of delivery / assembly of the product.
The client is responsible for any additional
installation charges associated with return visits.
• Electrical supply may uctuate in your
area. To ensure stable performance of the
product, use the proper gauge wire.
DANGER!
Improper connection of the equipmentgrounding conductor can result in a risk of
electric shock. Check with a qualied electrician
or serviceman if you are in doubt as to whether
the product is properly grounded. Do not
modify the plug provided with the product.
If it will not t the outlet, have a proper
outlet installed by a qualied electrician.
POWER REQUIREMENTS
North American
power cord plugs
shown. Depending
on your country, the
plug type may vary.
110 NEMA 5-15P
PLUG
220 NEMA 6-20P
PLUG
5
UNPACKING
Unpack the equipment where you will be using it. Place the carton
on a level at surface. It is recommended that you place a protective
covering on your oor. Never open box when it is on its side.
IMPORTANT NOTES
During each assembly step, ensure that ALL nuts and
bolts are in place and partially threaded.
Several parts have been pre-lubricated to aid in assembly
and usage. Please do not wipe this off. If you have diculty,
a light application of lithium grease is recommended.
WARNING!
There are several areas during the assembly process that special
attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are rmly tightened. If
the assembly instructions are not followed correctly, the equipment could
have parts that are not tightened and will seem loose and may cause
irritating noises. To prevent damage to the equipment, the assembly
instructions must be reviewed and corrective actions should be taken.
NEED HELP?
If you have questions or if there are any missing parts, contact Customer
Tech Support. Contact information is located on the information card.
ASSEMBLY
Upright Cycles
Page
8
Recumbent Cycles
Page
12
Hybrid Cycles
Page
17
6
PULSE GRIPS
WATER BOTTLE POCKETS
HANDLEBARS
SEAT
CRANK
PEDALS
REAR FRAME HANDLE
REAR FRAME COVER
REAR STABILIZER TUBE
MAIN FRAME
RESISTANCE TOGGLES
CONSOLE
ACCESSORY TRAY
CONSOLE MAST
SEAT ADJUSTMENT LEVER
STEP PLATE
FRONT SHROUD COVER
FRONT STABILIZER TUBE
TRANSPORT WHEELS
POWER CORD SOCKET
U7xi
U7xe
U5x
U3xe
U3x
7
1
TOOLS REQUIRED:
F 4 mm Allen Wrench
F 6 mm Allen Wrench
F 8 mm Allen Wrench
F Flat Wrench (15mm/17mm 325L)
F Phillips Screwdriver
PARTS INCLUDED:
F 1 Main Frame
F 1 Rear Stabilizer Tube
F 1 Front Stabilizer Tube
F 1 Rear Frame Handle
F 1 Rear Frame Cover
F 1 Console Mast
F 1 Seat
F 1 Arm Rest Handlebars
F 1 Front Shroud Cover
F 1 Pulse Grip Handlebars
F 2 Pedals
F 1 Hardware Kit
F 1 Power Cord
(included with 3xe, 7xe, and 7xi console)
Console sold separately
U7xi
U7xe
U5x
U3xe
U3x
Upright Cycle Assembly
A
B
Yellow Hardware Bag
Description Qty
ABBolt
Flat Washer
8
8
8
2 3
U7xi
U7xe
U5x
U3xe
U3x
C
D
E
F
Black / Red Hardware Bags
Description Qty
C
D
E
F
Bolt (black)
Screw
Bolt (chrome)
Tooth Washer
2
2
4
4
G
G
Green Hardware Bag
Description Qty
G Screw 4
Loading...