Matrix VS-S78 Glute Owner's Manual

Download

Page 1

OWNERS MANUAL

Versa Single-Station Strength

VS-S78 Glute

Page 2

Table Of Contents

Safety, General Care & Maintenence .............................................3

Getting Started (Product Specifications) ...................................... 5

Assembly Information ......................................................................6

Markings .............................................................................................7

Parts List ............................................................................................8

Installation & Assembly: Value Line

Part 1 Weight Stack & User Frame Assembly ........................9

Part 2 Cable Assembly ..............................................................14

Part 3 Exercise Arm Assembly ................................................15

Part 4 Pad Assembly .................................................................. 17

Part 5 Plastics Assembly ..........................................................19

Installation & Assembly: Optional Kits

Part 6 Premium Kit Assembly ..................................................22

Page 3

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

It is the sole responsibility of the purchaser of Matrix products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment.

It is recommended that all users of Matrix exercise equipment be informed of the following information prior to its use.

PROPER USAGE

Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that Matrix equipment be used properly to avoid injury.

Keep hands and feet clear at all times from moving parts to avoid injury.

CHECK FOR DAMAGED PARTS

1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by your country’s local Matrix dealer.

2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important information. If unreadable or missing, contact your Matrix dealer for a replacement.

3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking or tipping over. This must be performed by a licensed contractor.

4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals.

5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. Matrix dealers will provide service and maintenance training at our corporate facility upon request.

Page 4

IMPORTANT SAFETY INSTRUCTIONS

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW THESE PRECAUTIONS TO AVOID INJURY!

1. Never allow children on strength training equipment. Teenagers must be supervised at all times while using this equipment.

2. All warnings and instructions should be read and proper instruction obtained prior to use.

3. Use this equipment for its intended purposes only.

4. NEVER allow resistance straps, ropes or other means be attached to this equipment, as this may result in serious

injury.

5. NEVER use this equipment for support during stretching, as this may result in serious injury.

6. Cease exercise if you feel faint or dizzy. Obtain a medical exam before beginning an exercise program.

7. Keep body, hair, clothing and accessories free and clear of all moving parts.

8. Inspect the machine before use. DO NOT use machine if it appears damaged or inoperable.

9. Check to see that the selector pin is completely inserted into the weight stack.

10. NEVER use this machine with the weight stack pinned in an elevated position.

11. NEVER use dumbells or other means to incrementally increase the weight resistance. Only use the means provided directly from the manufacturer.

12. This equipment should only be used in supervised areas where access and control are regulated by the owner.

Page 5

EXERCISE PLACARD | PRODUCT SPECIFICATIONS | MAINTENANCE CHECKLIST

EXERCISE PLACARD

PRODUCT SPECIFICATIONS

TECH SPECS

Overall dimensions 53”L X 40”W X 66”H

Weight 450 lbs (205 kg)

Shipping weight 300 lbs (137 kg)

GETTING STARTED

WARRANTY (Valid in USA only)

Frame (not coatings) 10 years

Structural parts 10 years

Weight stacks 5 years

Pulleys 5 years

Pivot bearings 5 years

Any items not specified 3 years

Labor (excluding upholstery/cables/grips) 3 years

Upholstery/cables/grips/springs 1 year

MAINTENANCE CHECKLIST

ACTION FREQUENCY

Clean Upholstery Daily

Inspect Cables Daily

Clean Guide Rods Monthly

Inspect Hardware Monthly

Inspect Frame Bi-Annually

Clean Machine As Needed

Clean Grips As Needed

Lubricate Guide Rods As Needed

Upholstery & Grips should be cleaned with a non-ammonia based cleaner or a mild soap and water. Guide rods should be lubricated with Teflon based lubricant. Apply the lubricant to a cotton cloth and then apply up and down the guide rods.

Page 6

ASSEMBLY

UNPACKING | TOOLS REQUIRED

UNPACKING

Thank you for purchasing a Matrix product. This machine is an EN957-1 and EN957-2 compliant Class S product. Your Matrix product is inspected before it is packaged. It is shipped in multiple pieces to facilitate the compact packaging of the machine. Prior to assembly, confirm all the components by matching them with the exploded diagrams. Carefully unpack the unit from this box and dispose of the packing materials in accordance with your local laws.

CAUTION

The weight of the product is 300 lbs. (137 kg) not including the weight stack. The weight stack for this machine is 150 lbs. (68 kg). To avoid injury to yourself and prevent damage to the frame components, be sure to have proper assistance removing the frame pieces from this box. Please be sure to install the equipment on a stable base, properly level the machine and leave at least two feet of clearance to enter and exit the machine. Maximum user weight for this machine is 300 lbs.

TOOLS REQUIRED FOR ASSEMBLY

3MM L-Shaped Allen Wrench 4MM L-Shaped Allen Wrench 5MM L-Shaped Allen Wrench 6MM L-Shaped Allen Wrench 8MM L-Shaped Allen Wrench 10MM L-Shaped Allen Wrench Phillips & Standard Screwdrivers 8MM Open-End Wrench 13MM Open-End Wrench 17MM Open-End Wrench. 19MM Open-End Wrench Adjustable Wrench

Blue Locktite 242 must be used on all fasteners that are not assembled with Nylock Nuts

Page 7

MARKINGS

WARNING LABEL LOCATIONS

Page 8

Parts List

1 M10 X 125L Socket Head Cap Screw 4

2 M10 Flat Washer 25

3 Wide Cupped Flange 1

4 User Frame 1

5 M10 Nylock Nut 4

6 Upper Connecting Tube 1

7 M10 X 20L Socket Head Cap Screw 16

8 Outer Footpad Support Tube 1

9 Inner Footpad Support Tube 1

10 Weight Stack Frame 1

11 M8 X 20L Flathead Countersunk Screw 4

12 Foot Plate 1

13 M8 Flat Washer 6

14 M8 Nylock Nut 4

15 Rubber Footpad 1

DESCRIPTION

QTY

16 Rear Stack Support 1

17 M10 Flat Washer (Small Diameter) 4

18 M8 X 25L Socket Head Cap Screw 6

19 M10 X 55L Socket Head Cap Screw 1

20 Pulley Cover 1

21 Pulley 1

22 Cable Keeper 1

23 Cable 1

24 Exercise Arm 1

25 Large M10 Flat Washer (Ø38 mm) 1

26 Black Pivot Cover 1

27 M10 X 25L Socket Head Cap Screw 5

28 Arm Pad 2

29 Chest Pad 1

30 Chest Pad Adjustment Tube 1

Page 9

Parts List

31 Front Shroud 1

32 Rear Shroud 1

33 Large M8 Flat Washer (Ø20 mm) 4

34 Top Cap 1

35 Top Cap Cover 2

PREMIUM KIT COMPONENTS

1P Wing 1

2P Rep Counter 1

3P Towel Hook 1

4P ASG Pull Grip 2

5P Premium Pullpin 1

DESCRIPTION

QTY

Page 10

STEP 1 | USER FRAME INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

1 M10 X 125L SHC 4

2 M10 Flat Washer 14

3 Wide Cupped Flange 1

4 User Frame 1

5 M10 Nylock Nut 4

6 Upper Connecting Tube 1

7 M10 X 20L SHC 6

8 Outer Footpad Support 1

9 Inner Footpad Support 1

10 Weight Stack Frame 1

ASSEMBLY

PART 1: USER FRAME ASSEMBLY

Install the user frame hardware as shown, but DO NOT FULLY TIGHTEN .

Page 11

STEP 2 | FOOT PAD INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

11 M8 X 20L FHSC 4

12 Foot Plate 1

13 M8 Flat Washer 4

14 M8 Nylock Nut 4

Tip machine back to access lower hardware (items 13 & 14)

ASSEMBLY

PART 1: USER FRAME ASSEMBLY

Ensure that the frame is level and that all floor pads contact the floor equally,

Torque all M10 Frame Hardware on page 10 to: 77 N-m/57 ft/lbs.

Torque M8 hardware to: 39 N-m/29 ft-lbs.

Install the user frame hardware as shown.

Page 12

STEP 3 | RUBBER PAD INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

15 Rubber Footpad 1

ASSEMBLY

PART 1: USER FRAME ASSEMBLY

Wrap the entire lip of pad around the metal foot plate as shown in detail view.

Page 13

ASSEMBLY

PART 1: STACK & USER FRAME ASSEMBLY

STEP 4 | WEIGHT STACK TO USER FRAME ASSEMBLY INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

7 M10 X 20L SHC 4

13 M8 Flat Washer 2

16 Rear Stack Support 1

17 M10 Flat Washer (Small Dia.) 4

18 M8 X 25L SHC 2

Torque M10 Hardware to: 77 N-m/57 ft/lbs.

Torque M8 hardware to: 39 N-m/29 ft-lbs.

Page 14

STEP 1 | PULLEY ASSEMBLY INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

2 M10 Flat Washer 1

19 M10 X 55L SHC 1

20 Pulley Cover 1

21 Pulley 1

22 Cable Keeper 1

23 Cable 1

ASSEMBLY

PART 2: CABLE ASSEMBLY

Install the pulley and pulley guard as shown.

Tighten to 77 N-m/57 ft-lbs.

Page 15

STEP 1 | EXERCISE ARM ASSEMBLY INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

24 Exercise Arm 1

25 M10 Washer (Ø38 mm) 1

26 Black Pivot Cover 1

27 M10 X 25L SHC 1

ASSEMBLY

PART 3: EXERCISE ARM ASSEMBLY

Torque to 77 N-m/57 ft-lbs.

Page 16

ASSEMBLY

PART 3: EXERCISE ARM ASSEMBLY

STEP 2 | EXERCISE ARM AND CABLE ASSEMBLY INSTRUCTIONS & NOTES

Cable tension is adjusted by raising or lowering pulley as shown in View A.

Note: Nuts for adjustable pulley must be on inside towards weight plates.

View A

Page 17

STEP 1 | ARM PAD ASSEMBLY INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

2 M10 Flat Washer 6

7 M10 X 20L SHC 6

28 Arm Pad 2

ASSEMBLY

PART 4: PAD ASSEMBLY

Install the pad as shown.

Tighten to 27 N-m/20 ft-lbs.

Page 18

STEP 2 | CHEST PAD ASSEMBLY INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

2 M10 Flat Washer 4

27 M10 X 25L SHC 4

29 Chest Pad 1

30 Chest Pad Adjustment Tube 1

Install the pad as shown. Tighten to 27 N-m/20 ft-lbs.

ASSEMBLY

PART 4: PAD ASSEMBLY

Remove limit pin before assembling pad assembly.

Reinstall after installing pad assembly

Page 19

STEP 1 | SHROUD ASSEMBLY ASSEMBLY INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

31 Front Shroud 1

32 Rear Shroud (Not shown) 1

Position hangers in their lowest position

ASSEMBLY

PART 5: PLASTICS ASSEMBLY

Install the weight stack shrouds as shown.

Page 20

STEP 2 | TOP CAP ASSEMBLY INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

18 M8 X 25L SHC 4

33 M8 Flat Washer (20 mm diameter) 4

34 Top Cap 1

ASSEMBLY

PART 5: PLASTICS ASSEMBLY

Install the top cap onto the weight stack as shown.

Position top cap so that the instructional placard faces the user.

Torque to 17 N-m/147 in-lbs.

Page 21

STEP 3 | TOP CAP COVERS INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

35 Top Cap Cover 2

ASSEMBLY

PART 5: PLASTICS ASSEMBLY

Install the top cap covers.

Page 22

PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

1P Wing 1

2P Rep Counter 1

3P Towel Hook 1

4P ASG Pull Grip 2

5P Premium Pullpin 1

ASSEMBLY

PART 6: PREMIUM KIT ASSEMBLY

IMPORTANT NOTICE

PLEASE NOTE:

Be sure to remove the insulating sheet when installing the Rep Counter.

Page 23

STEP 1 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

Rep Counter - Magnet

1. Remove the (2) top cap covers using a flat blade screw driver.

2. Remove the (4) M8 bolts and 20 mm diameter washers that hold the top cap to the weight stack frame.

Top cap covers, 20 mm diameter washers

& M8 screws can be discarded

ASSEMBLY

PART 6: PREMIUM KIT ASSEMBLY

3. Remove top cap and rear shroud.

4. Assemble the Repetition Counter magnet holder to the headplate using the M5 X 12L bolt and M5 washer provided with the kit.

Holder must be mounted on thes same side of

the weight stack as Rep Counter

Page 24

ASSEMBLY

PART 6: PREMIUM KIT ASSEMBLY

STEP 2 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

Rep Counter - Sensors

1. Assemble Rep Counter sensor base using (4) screws included with the kit.

2. Assemble (3) sensors located per machine chart shown below.

Thread zip ties through holes to secure cables

Route wires in groove

Machine Sensor Locations (Sensor “A” = Top, “B” = Middle, “C” = Bottom)

Chest Press A2, B7, C13

Shoulder Press A1, B4, C13

Leg Extension A1, B7, C13

Seated Leg Curl A6, B10, C13

Leg Press A6, B10, C13

Lat Pulldown A1, B3, C13

Triceps Press A5, B8, C13

Seated Row A1, B4, C13

Bicep Curl A6, B8, C13

Hip Add/Abduction A7, B11, C13

Pec Fly/Rear Delt A7,B 9, C13

Abdominal A8, B10, C13

Back Extension A6, B8, C13

Glute A2, B7, C13

Page 25

STEP 3 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

Rep Counter

1. Remove and discard hole caps using caution not to scratch the paint.

ASSEMBLY

PART 6: PREMIUM KIT ASSEMBLY

2. Attach plug to Rep Counter.

3. Assemble Towel Hook (3P) and Rep Counter (2P) using the M8 X 35L SHC bolts provided.

Rep Counter wires must be routed

through the center of the Towel Hook

4. Torque bolts to 17 N-m/147 in-lbs.

Page 26

STEP 4 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

Wing

Assemble the wing (1P) as shown using the M8

hardware provided with the kit. Tighten to 39N-m (29 ft-lbs.).

ASSEMBLY

PART 6: PREMIUM KIT ASSEMBLY

Page 27

STEP 5 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

ASG Grips

ASSEMBLY

PART 6: PREMIUM KIT ASSEMBLY

1. Remove the end caps using a 3 mm Allen wrench.

2. Cut off and discard the grips.

3. Remove inner collars with a 3 mm allen wrench.

4. Assemble the ASG grip (4P) as shown; lock inner collars using a 4 mm Allen wench (torque to 8 N-m/5 ftlbs.), and a 3 mm Allen wrench to secure the end caps.

5. Orient ASG grips as shown, with thumb index in-line with arm pad for comfort.

Page 28