Matrix VS-S40 Owner's Manual

OWNERS MANUAL

Versa Single-Station Strength

VS-S40 Bicep Curl

Table Of Contents

Safety, General Care & Maintenence .................................................3

Getting Started (Product Specifications) .......................................... 5

Assembly Information ..........................................................................6

Markings ................................................................................................. 7

Parts List ................................................................................................8

Installation & Assembly: Value Line

Part 1 Weight Stack & User Frame Assembly .......................... 10

Part 2 Arm Assembly ....................................................................13

Part 3 Cable Assembly ................................................................. 14

Part 4 Handlebar Assembly ........................................................ 15

Part 5 Counter Weight Assembly ............................................... 16

Part 6 Pad Assembly .....................................................................17

Part 7 Plastics Assembly ............................................................ 19

Installation & Assembly: Optional Kits

Part 8 Premium Kit Assembly ....................................................22

Part 9 Short User Kit ...................................................................30

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

It is the sole responsibility of the purchaser of Matrix products to instruct all individuals, whether they are the end user or
supervising personnel on proper usage of the equipment.

It is recommended that all users of Matrix exercise equipment be informed of the following information prior to its use.

PROPER USAGE

Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that Matrix
equipment be used properly to avoid injury.

Keep hands and feet clear at all times from moving parts to avoid injury.

CHECK FOR DAMAGED PARTS

1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by your
country’s local Matrix dealer.

2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important information.
If unreadable or missing, contact your Matrix dealer for a replacement.

3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking or tipping over. This
must be performed by a licensed contractor.

4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your
liability to a minimum. Equipment needs to be inspected at regular intervals.

5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so.
Matrix dealers will provide service and maintenance training at our corporate facility upon request.

3

IMPORTANT SAFETY INSTRUCTIONS

WARNING: This product contains chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.

WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW
THESE PRECAUTIONS TO AVOID INJURY!

1. Never allow children on strength training equipment. Teenagers must be supervised at all times while using this
equipment.

2. All warnings and instructions should be read and proper instruction obtained prior to use.

3. Use this equipment for its intended purposes only.

4. NEVER allow resistance straps, ropes or other means be attached to this equipment, as this may result in serious

injury.

5. NEVER use this equipment for support during stretching, as this may result in serious injury.

6. Cease exercise if you feel faint or dizzy. Obtain a medical exam before beginning an exercise program.

7. Keep body, hair, clothing and accessories free and clear of all moving parts.

8. Inspect the machine before use. DO NOT use machine if it appears damaged or inoperable.

9. Check to see that the selector pin is completely inserted into the weight stack.

10. NEVER use this machine with the weight stack pinned in an elevated position.

11. NEVER use dumbells or other means to incrementally increase the weight resistance. Only use the means provided
directly from the manufacturer.

12. This equipment should only be used in supervised areas where access and control are regulated by the owner.

4

EXERCISE PLACARD | PRODUCT SPECIFICATIONS | MAINTENANCE CHECKLIST

EXERCISE PLACARD

PRODUCT SPECIFICATIONS

TECH SPECS

Overall dimensions 45”L X 50”W X 66”H

Weight

Shipping weight 325 lbs (148 kg)

Light Stack = 475 lbs (216 kg), Heavy Stack = 525 lbs (239
kg)

GETTING STARTED

WARRANTY (Valid in USA only)

Frame (not coatings) 10 years

Structural parts 10 years

Weight stacks 5 years

Pulleys 5 years

Pivot bearings 5 years

Any items not specified 3 years

Labor (excluding upholstery/cables/grips) 3 years

Upholstery/cables/grips/springs 1 year

MAINTENANCE CHECKLIST

ACTION FREQUENCY

Clean Upholstery Daily

Inspect Cables Daily

Clean Guide Rods Monthly

Inspect Hardware Monthly

Inspect Frame Bi-Annually

Clean Machine As Needed

Clean Grips As Needed

Lubricate Guide Rods As Needed

Upholstery & Grips should be cleaned with a non-ammonia based cleaner or a mild soap and water. Guide rods should be
lubricated with Teflon based lubricant. Apply the lubricant to a cotton cloth and then apply up and down the guide rods.

5

ASSEMBLY

UNPACKING | TOOLS REQUIRED

UNPACKING

Thank you for purchasing a Matrix product. This machine is an EN957-1 and EN957-2 compliant Class S product. Your Ma­trix product is inspected before it is packaged. It is shipped in multiple pieces to facilitate the compact packaging of the
machine. Prior to assembly, confirm all the components by matching them with the exploded diagrams. Carefully unpack
the unit from this box and dispose of the packing materials in accordance with your local laws.

CAUTION

The weight of the product is 325 lbs. (148 kg) not including the weight stack. The standard weight stack for this machine
is 150 lbs. (68 kg) & the heavy stack is 200 lbs. (91kg). To avoid injury to yourself and prevent damage to the frame compo­nents, be sure to have proper assistance removing the frame pieces from this box. Please be sure to install the equipment
on a stable base, properly level the machine and leave at least two feet of clearance to enter and exit the machine. Maxi­mum user weight for this machine is 300 lbs.

TOOLS REQUIRED FOR ASSEMBLY

3MM L-Shaped Allen Wrench
4MM L-Shaped Allen Wrench
5MM L-Shaped Allen Wrench
6MM L-Shaped Allen Wrench
8MM L-Shaped Allen Wrench
10MM L-Shaped Allen Wrench
Phillips & Standard Screwdrivers
8MM Open-End Wrench
13MM Open-End Wrench
17MM Open-End Wrench.
19MM Open-End Wrench
Adjustable Wrench

Blue Locktite 242 must be used on all fasteners that are not assembled with Nylock Nuts

6

MARKINGS

WARNING LABEL LOCATIONS

7

Parts List

ID

1 M10 X 125L Socket Head Cap Screw 4

2 M10 Flat Washer 22

3 Wide Cupped Flange 2

4 User Frame 1

5 M10 Nylock Nut 4

6 Lower Connecting Tube 1

7 M10 X 20L Socket Head Cap Screw 15

8 Weight Stack 1

9 Upper Connecting Tube 1

10 Rear Stack Support 1

11 M10 Flat Washer (Small Outside Diameter) 4

12 M8 X 20L Socket Head Cap Screw 4

13 M8 Flat Washer 2

14 CAM/Arm Assembly 1

15 Wave (Spring) Washer 1

DESCRIPTION

QTY

16 M10 Large Flat Washer (Ø42 mm) 1

17 Back Pivot Cap 1

18 M10 X 25L Socket Head Cap Screw 5

19 Counter Weight 1

20 Bottom Pad 1

21 M10 X 20L Hex Bolt 4

22 Arm Curl Pad 1

23 Front Shroud 1

24 Rear Shroud 1

25 M8 X 25L Socket Head Cap Screw 4

26 Large M8 Flat Washer (Ø20 mm) 6

27 Top Cap 1

28 Top Cap Cover 2

8

Parts List

ID

OPTIONAL PREMIUM KIT COMPONENTS

1P Wing 1

2P Rep Counter 1

3P Towel Hook 1

4P ASG Pull Grip 2

5P Premium Pullpin 1

OPTIONAL SHORT USER KIT

1SK Foot Rest 1

2SK M10 X 25L Socket Head Cap Screw 2

3SK M10 Flat Washer 2

DESCRIPTION

QTY

9

ASSEMBLY

8

7

6

5

3

2

1

4

PART 1: STACK & USER FRAME ASSEMBLY

STEP 1 | WEIGHT STACK TO USER FRAME ASSEMBLY INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

1 M10 X 125L SHC 2

2 M10 Flat Washer 6

3 Wide Cupped Flange 1

4 User Frame 1

5 M10 Nylock Nut 2

6 Lower Connecting Tube 1

7 M10 X 20L SHC 2

8 Weight Stack 1

Install the user frame hardware as shown, but DO NOT FULLY TIGHTEN .

10

ASSEMBLY

7

9

3

1

5

2

PART 1: STACK & USER FRAME ASSEMBLY

STEP 2 | WEIGHT STACK TO USER FRAME ASSEMBLY INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

1 M10 X 125L SHC 2

2 M10 Flat Washer 12

3 Wide Cupped Flange 1

5 M10 Nylock Nut 2

7 M10 X 20L SHC 8

9 Upper Connecting Tube 1

Install the user frame hardware as shown, but DO NOT FULLY TIGHTEN .

11

ASSEMBLY

13

12

11

10

PART 1: STACK & USER FRAME ASSEMBLY

STEP 3 | WEIGHT STACK TO USER FRAME ASSEMBLY INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

7 M10 X 20L SHC 4

10 Rear Stack Support 1

11 M10 Flat Washer (Small Dia.) 4

12 M8 X 20L SHC 2

13 M8 Flat Washer 2

Torque all M10 Frame Hardware on pages 9 through 11 to: 77 N-m/57 ft/lbs.

12

7

Install the user frame hardware as shown.

Torque M8 hardware to: 39 N-m/29 ft-lbs.`

STEP 1 | WEIGHT STACK CABLE ASSEMBLY INSTRUCTIONS & NOTES

14

15

16

17

18

ID DESCRIPTION QUANTITY

14 CAM/Arm Assembly 1

15 Wave (Spring) Washer 1

ASSEMBLY

PART 2: ARM ASSEMBLY

16

17 Black Pivot Cap 1

18 M10 X 25L SHC 1

M10 Flat Washer (Ø42mm OD)

1

Torque hardware to: 77 N-m/57 ft-lbs.

13

STEP 1 | EXERCISE ARM ASSEMBLY INSTRUCTIONS & NOTES

ASSEMBLY

PART 3: CABLE ASSEMBLY

Cable tension is adjusted by raising or lowering pulley as shown.

Note: Nuts for adjustable pulley must be on inside towards weight plates.

14

STEP 1 | HANDLEBAR ASSEMBLY INSTRUCTIONS & NOTES

7

ID DESCRIPTION QUANTITY

7 M10 X 20L SHC 1

ASSEMBLY

PART 4: HANDLEBAR ASSEMBLY

Tighten to: 77 N-m/57 ft-lbs.

15

PART 5: COUNTER WEIGHT ASSEMBLY

19

13

12

STEP 1 | COUNTER WEIGHT ASSEMBLY INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

12 M8 X 20L SHC 2

13 M8 Flat Washer 2

19 Counter Weight 1

ASSEMBLY

16

Tighten to: 39 N-m/29 ft-lbs.

STEP 1 | PAD ASSEMBLY INSTRUCTIONS & NOTES

21

20

ID DESCRIPTION QUANTITY

20 Bottom Pad 1

21 M10 X 20L Hex Bolt 4

ASSEMBLY

PART 6: PAD ASSEMBLY

Install the pad as shown.

Tighten to 27 N-m/20 ft-lbs.

17

STEP 2 | ARM CURL PAD ASSEMBLY INSTRUCTIONS & NOTES

22218

ID DESCRIPTION QUANTITY

2 M10 Flat Washer 4

18 M10 X 25L SHC 4

22 Arm Curl Pad 1

ASSEMBLY

PART 6: PAD ASSEMBLY

18

Install the pad as shown.

Tighten to 27 N-m/20 ft-lbs.

STEP 1 | SHROUD ASSEMBLY ASSEMBLY INSTRUCTIONS & NOTES

23

ID DESCRIPTION QUANTITY

23 Front Shroud 1

24 Rear Shroud (Not shown) 1

Position hangers in their lowest position

ASSEMBLY

PART 7: PLASTICS ASSEMBLY

Install the weight stack shrouds as shown.

19

STEP 2 | TOP CAP ASSEMBLY INSTRUCTIONS & NOTES

26

25

27

ID DESCRIPTION QUANTITY

25 M8 X 25L SHC 4

26 M8 Flat Washer (20 mm diameter) 4

27 Top Cap 1

ASSEMBLY

PART 7: PLASTICS ASSEMBLY

Install the top cap onto the weight stack as shown.

Position top cap so that the instructional placard faces the user.

20

Torque to 17 N-m/147 in-lbs.

STEP 3 | TOP CAP COVERS INSTRUCTIONS & NOTES

28

28

ID DESCRIPTION QUANTITY

28 Top Cap Cover 2

ASSEMBLY

PART 7: PLASTICS ASSEMBLY

Install the top cap covers.

21

PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

ID DESCRIPTION QUANTITY

1P Wing 1

2P Rep Counter 1

3P Towel Hook 1

4P ASG Pull Grip 2

5P Premium Pullpin 1

6P Seat Assist Gas Shock 1

ASSEMBLY

PART 8: PREMIUM KIT ASSEMBLY

1P

4P

2P

3P

5P

6P

22

IMPORTANT NOTICE

PLEASE NOTE:

Be sure to remove the insulating
sheet when installing the
Rep Counter.

STEP 1 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

Rep Counter - Magnet

1. Remove the (2) top cap covers using a flat
blade screw driver.

2. Remove the (4) M8 bolts and 20 mm diameter
washers that hold the top cap to the weight
stack frame.

Top cap covers, 20 mm diameter washers &

M8 screws can be discarded

ASSEMBLY

PART 8: PREMIUM KIT ASSEMBLY

3. Remove top cap and rear shroud.

4. Assemble the Repetition Counter magnet holder
to the headplate using the M5 X 12L bolt and M5
washer provided with the kit.

Holder must be mounted on thes same

side of the weight stack as Rep Counter

23

STEP 2 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

Rep Counter - Sensors

1. Assemble Rep Counter sensor base using
(4) screws included with the kit.

2. Assemble (3) sensors located per machine
chart shown below.

Thread zip ties through
holes to secure cables

Route wires in groove

ASSEMBLY

PART 8: PREMIUM KIT ASSEMBLY

24

Machine Sensor Locations (Sensor “A” = Top, “B” = Middle, “C” = Bottom)

Chest Press A2, B7, C13

Shoulder Press A1, B4, C13

Leg Extension A1, B7, C13

Seated Leg Curl A6, B10, C13

Leg Press A6, B10, C13

Lat Pulldown A1, B3, C13

Triceps Press A5, B8, C13

Seated Row A1, B4, C13

Bicep Curl A6, B8, C13

Hip Add/Abduction A7, B11, C13

Pec Fly/Rear Delt A7,B 9, C13

Abdominal A8, B10, C13

Back Extension A6, B8, C13

Glute A2, B7, C13

STEP 3 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

Rep Counter

1. Remove and discard hole caps using cau­tion not to scratch the paint.

ASSEMBLY

PART 8: PREMIUM KIT ASSEMBLY

2. Attach plug to Rep Counter.

3. Assemble Towel Hook (3P) and Rep Counter
(2P) using the M8 X 35L SHC bolts provided.

Rep Counter wires must be

routed through the center of

the Towel Hook

4. Torque bolts to 17 N-m/147 in-lbs.

25

STEP 4 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

Wing

Assemble the wing (1P) as shown using the M8

hardware provided with the kit. Tighten to 39N-m
(29 ft-lbs.).

ASSEMBLY

PART 8: PREMIUM KIT ASSEMBLY

26

STEP 5 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

ASG Grips

ASSEMBLY

PART 8: PREMIUM KIT ASSEMBLY

Reuse

1. Remove the end caps using a 5 mm Allen wrench.

2. Slide off the grip assembly.

3. Remove inner collars with a 3 mm allen wrench.

4. Assemble the ASG grip as shown; lock inner & outer collars
using a 4 mm Allen wrench (torque to 8 N-m/5 ft-lbs.), and a
5 mm Allen wrench to secure the end caps

27

STEP 6 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

Pull Pin

ASSEMBLY

PART 8: PREMIUM KIT ASSEMBLY

Remove the pull pin using an adjustable wrench, and replace with the Premium pull pin (5P).

28

STEP 6 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES

Seat Assist Shock

2

1

Raise the seat to the highest position
before adding gas shock (6P)

3

ASSEMBLY

PART 8: PREMIUM KIT ASSEMBLY

4

5

Disassembly and assembly for both ends

of shock (Only one end is shown)

Shock must be positioned as shown with gas cylinder above piston rod

29

STEP 1 | FOOT REST ASSEMBLY INSTRUCTIONS & NOTES

1SK

3SK

2SK

ID DESCRIPTION QUANTITY

1SK Foot Rest 1

2SK M10 X 25L SHC 2

3SK M10 Flat Washer 2

ASSEMBLY

PART 9: FOOT REST ASSEMBLY

30

Install the foot rest as shown.

Tighten to 77 N-m/57 ft-lbs.

Matrix Fitness

1600 Landmark Drive
Cottage Grove WI 53527

matrixfitness.com

Toll-free 866.693.4863
Facsimilie 608.839.8687

Versa Bicep Curl Owners Guide Rev.1.2 Copyright © 2013 Matrix Fitness