Page 1
OWNERS MANUAL
Versa Single-Station Strength
VS-S34 Seated Row
G1_OM_Seated Row Rev.1.1.indd 1 11/19/13 4:29 PM
Page 2
3
Table Of Contents
Safety, General Care & Maintenence ................................................ 3
Getting Started (Product Specifications) .........................................5
Assembly Information .........................................................................6
Markings ................................................................................................ 7
Parts List ............................................................................................... 8
Installation & Assembly: Value Line
Part 1 Weight Stack to User Frame Assembly .........................10
Part 2 Cable Assembly ................................................................ 11
Part 3 Pad Assembly ....................................................................19
Part 4 Foot Rest Assembly .........................................................21
Part 5 Plastics Assembly ...........................................................22
Part 6 Cable Adjustment ............................................................25
Installation & Assembly: Optional Kits
Part 7 Premium Kit Assembly ....................................................26
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
It is the sole responsibility of the purchaser of Matrix products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment.
It is recommended that all users of Matrix exercise equipment be informed of the following information prior to its use.
PROPER USAGE
Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that Matrix equipment
be used properly to avoid injury.
Keep hands and feet clear at all times from moving parts to avoid injury.
CHECK FOR DAMAGED PARTS
1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by your
country’s local Matrix dealer.
2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important information.
If unreadable or missing, contact your Matrix dealer for a replacement.
3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking or tipping over. This
must be performed by a licensed contractor.
4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals.
5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so.
Matrix dealers will provide service and maintenance training at our corporate facility upon request.
G1_OM_Seated Row Rev.1.1.indd 2-3 11/19/13 4:29 PM
Page 3
4 5
GETTING STARTED
TECH SPECS
Overall dimensions 57”L X 40”W X 66 ”H
Weight
Light Stack = 471 lbs (214 kg), Heavy Stack = 541 lbs (246
kg)
Shipping weight 311 lbs (142 kg)
WARRANTY (Valid in USA only)
Frame (not coatings) 10 years
Structural parts 10 years
Weight stacks 5 years
Pulleys 5 years
Pivot bearings 5 years
Any items not specified 3 years
Labor (excluding upholstery/cables/grips) 3 years
Upholstery/cables/grips/springs 1 year
ACTION FREQUENCY
Clean Upholstery Daily
Inspect Cables Daily
Clean Guide Rods Monthly
Inspect Hardware Monthly
Inspect Frame Bi-Annually
Clean Machine As Needed
Clean Grips As Needed
Lubricate Guide Rods As Needed
Upholstery & Grips should be cleaned with a non-ammonia based cleaner (like Simple Green) or a mild soap and water.
Guide rods should be lubricated with Teflon based lubricant. Apply the lubricant to a cotton cloth and then apply up and
down the guide rods.
MAINTENANCE CHECKLIST
EXERCISE PLACARD | PRODUCT SPECIFICATIONS | MAINTENANCE CHECKLIST
EXERCISE PLACARD
PRODUCT SPECIFICATIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW
THESE PRECAUTIONS TO AVOID INJURY!
1. Never allow children on strength training equipment. Teenagers must be supervised at all times while using this
equipment.
2. All warnings and instructions should be read and proper instruction obtained prior to use.
3. Use this equipment for its intended purposes only.
4. NEVER allow resistance straps, ropes or other means be attached to this equipment, as this may result in serious
injury.
5. NEVER use this equipment for support during stretching, as this may result in serious injury.
6. Cease exercise if you feel faint or dizzy. Obtain a medical exam before beginning an exercise program.
7. Keep body, hair, clothing and accessories free and clear of all moving parts.
8. Inspect the machine before use. DO NOT use machine if it appears damaged or inoperable.
9. Check to see that the selector pin is completely inserted into the weight stack.
10. NEVER use this machine with the weight stack pinned in an elevated position.
11. NEVER use dumbells or other means to incrementally increase the weight resistance. Only use the means provided
directly from the manufacturer.
12. This equipment should only be used in supervised areas where access and control are regulated by the owner.
G1_OM_Seated Row Rev.1.1.indd 4-5 11/19/13 4:29 PM
Page 4
6 7
ASSEMBLY
UNPACKING | TOOLS REQUIRED
UNPACKING
Thank you for purchasing a Matrix product. This machine is an EN957-1 and EN957-2 compliant Class S product. Your Matrix product is inspected before it is packaged. It is shipped in multiple pieces to facilitate the compact packaging of the
machine. Prior to assembly, confirm all the components by matching them with the exploded diagrams. Carefully unpack
the unit from this box and dispose of the packing materials in accordance with your local laws.
CAUTION
The weight of the product is 311lbs. (142 kg) not including the weight stack. The standard weight stack for this machine is
160 lbs. (73 kg) & the heavy stack is 23 0 lbs. (105kg). To avoid injury to yourself and prevent damage to the frame components, be sure to have proper assistance removing the frame pieces from this box. Please be sure to install the equipment
on a stable base, properly level the machine and leave at least two feet of clearance to enter and exit the machine. Maximum user weight for this machine is 300 lbs.
TOOLS REQUIRED FOR ASSEMBLY
3MM L-Shaped Allen Wrench
4MM L-Shaped Allen Wrench
5MM L-Shaped Allen Wrench
6MM L-Shaped Allen Wrench
8MM L-Shaped Allen Wrench
10MM L-Shaped Allen Wrench
Phillips & Standard Screwdrivers
8MM Open-End Wrench
13MM Open-End Wrench
17MM Open-End Wrench.
19MM Open-End Wrench
Adjustable Wrench
Blue Locktite 242 must be used on all fasteners that are not assembled with Nylock Nuts
MARKINGS
WARNING LABEL LOCATIONS
G1_OM_Seated Row Rev.1.1.indd 6-7 11/19/13 4:29 PM
Page 5
8 9
Parts List
ID
DESCRIPTION
QTY
30 Bottom Pad 1
31 M10 X 20L Hex Bolt 4
32 Foot Rest 1
33 M10 X 80L Socket Head Cap Screw 2
34 Front Shroud 1
35 Rear Shroud 1
36 M8 X 25L SHC 4
37 Large M8 Flat Washer (Ø20 mm) 4
38 Top Cap 1
39 Top Cap Cover 2
PREMIUM KIT COMPONENTS
1P Wing 1
2P Rep Counter 1
3P Towel Hook 1
4P ASG Pull Grip 2
5P Premium Pullpin 4
Parts List
ID
DESCRIPTION
QTY
1 M10 X 125L Socket Head Cap Screw 2
2 M10 Flat Washer 32
3 Wide Cupped Flange 1
4 User Frame 1
5 M10 Nylock Nut 5
6 Lower Connecting Tube 1
7 M10 X 20L Socket Head Cap Screw 16
8 Upper Connecting Tube 1
9 Weight Stack Frame 1
10 Cable Keeper 3
11 Pulley 6
12 Pulley Cover 3
13 M10 X 50L Socket Head Cap Screw 4
14 Cable Retaining Clip 1
15 Floating Pulley Bracket 1
16 Weight Stack Cable 1
17 User Cable 1
18 M10 Lock Washer 4
19 Axle 2
20 Swivel Pulley Assembly 2
21 Hand Grip 2
22 Pin 2
23 Cable Clevis 2
24 Plastic Bullet Cover 2
25 M5 X 30L Socket Head Cap Screw 2
26 M5 Nylock Nut 2
27 Chest Pad 1
28 Chest Pad Back Cover 1
29 Chest Pad Adjustment Tube 1
30 M10 X 25L Socket Head Cap Screw 6
G1_OM_Seated Row Rev.1.1.indd 8-9 11/19/13 4:29 PM
Page 6
10 11
5
2
7
6
9
3
1
8
4
PART 1: STACK & USER FRAME ASSEMBLY
STEP 1 | WEIGHT STACK TO USER FRAME INSTRUCTIONS & NOTES
ASSEMBLY
ID DESCRIPTION QUANTITY
1 M10 X 125L SHC 2
2 M10 Flat Washer 12
3 Wide Cupped Flange 1
4 User Frame 1
5 M10 Nylock Nut 2
6 Lower Connecting Tube 1
7 M10 X 20L SHC 8
8 Upper Connecting Tube 1
9 Weight Stack Frame 1
Install the user frame hardware as shown, but DO NOT FULLY TIGHTEN .
After weight plates have been assembled torque all frame hardware to: 77 N-m/57 ft-lbs.
ASSEMBLY
STEP 1 | BOTTOM PULLEY ASSEMBLY INSTRUCTIONS & NOTES
PART 2: CABLE ASSEMBLY
ID DESCRIPTION QUANTITY
2 M10 Flat Washer 2
10 Cable Keeper 1
11 Pulley 1
12 Pully Cover 1
13 M10 X 50L SHC 1
Torque hardware to: 77 N-m/57 ft-lbs.
Assemble the components as shown, making sure to orient the cable keeper as shown, as well as to sandwich the
pulley cover between the two flat washers.
13
2
12
10
11
G1_OM_Seated Row Rev.1.1.indd 10-11 11/19/13 4:29 PM
Page 7
12 13
ASSEMBLY
STEP 2 | FLOATING PULLEY ASSEMBLY INSTRUCTIONS & NOTES
PART 2: CABLE ASSEMBLY
ID DESCRIPTION QUANTITY
14 Cable Retaining Clip 1
15 Floating Pulley Bracket 1
16 Weight Stack Cable 1
16
14
15
1. Assemble the stack cable end fitting through floating pulley bracket opening.
2. Raise the cable up.
3. Slide the clevis onto the cable end fitting.
4. Seat the cable and clevis into the bottom of the floating pulley bracket.
1
2
3
ASSEMBLY
STEP 3 | FLOATING PULLEY ASSEMBLY INSTRUCTIONS & NOTES
PART 2: CABLE ASSEMBLY
ID DESCRIPTION QUANTITY
2 M10 Flat Washer 2
5 M10 Nylock Nut 1
11 Pulley 1
13 M10 X 50L SHC 1
17 User Cable 1
Assemble pulley as shown. Torque hardware to 77 N-m/74 ft-lbs.
5
17
11
2
13
G1_OM_Seated Row Rev.1.1.indd 12-13 11/19/13 4:29 PM
Page 8
14 15
PART 2: CABLE ASSEMBLY
STEP 4 | LEFT & RIGHT UPPER PULLEY ASSEMBLY INSTRUCTIONS & NOTES
ID DESCRIPTION QUANTITY
2 M10 Washer 4
10 Cable Keeper 2
11 Pulley 2
12 Pulley Cover 2
13 M10 X 50L SHC 2
ASSEMBLY
13
2
10
12
11
Assemble the components as shown, making sure to orient the cable keeper as shown, as well as to sandwich the
pulley cover between the two flat washers.
PART 2: CABLE ASSEMBLY
STEP 5 | LEFT & RIGHT SWIVELLING PULLEY ASSEMBLY INSTRUCTIONS & NOTES
ID DESCRIPTION QUANTITY
2 M10 Flat Washer 4
7 M10 X 20L SHC 4
18 M10 Lock Washer 4
19 Axle 2
20 Swivel Pulley Assembly 2
ASSEMBLY
Assemble the components as shown, making sure to orient the flat features of the axle and pulley bracket to each
other. Torque hardware to: 77 N-m/57 ft-lbs.
2
19
18
7
20
G1_OM_Seated Row Rev.1.1.indd 14-15 11/19/13 4:29 PM
Page 9
16 17
PART 2: CABLE ASSEMBLY
STEP 6 | USER CABLE ROUTING
ASSEMBLY ASSEMBLY
STEP 7 | HANDLE ASSEMBLY INSTRUCTIONS & NOTES
PART 2: CABLE ASSEMBLY
ID DESCRIPTION QUANTITY
21 Hand Grip 2
22 Pin 2
23 Cable Clevis 2
24 Plastic Bullet Cover 2
23
24
22
21
24
Insert pin into clevis as shown. Line up pin to
notches in bullet cover as shown below
G1_OM_Seated Row Rev.1.1.indd 16-17 11/19/13 4:29 PM
Page 10
18 19
ASSEMBLY
STEP 7 | HANDLE ASSEMBLY INSTRUCTIONS & NOTES
PART 2: CABLE ASSEMBLY
ID DESCRIPTION QUANTITY
25 M5 X 30L SHC 2
26 M5 Nylock Nut 2
Locate Nylock Nut into hex pocket in bullet
cover as shown. Torque to: 10 N-m/84 in-lbs.
26
25
STEP 1 | CHEST PAD ASSEMBLY INSTRUCTIONS & NOTES
ID DESCRIPTION QUANTITY
2 M10 Flat Washer 4
7 M10 X 20L SHC 4
27 Chest Pad 1
28 Chest Pad Back Cover 1
29 Chest Pad Adjustment Tube 1
ASSEMBLY
PART 3: PAD ASSEMBLY
Install the pad as shown.
Tighten to 57 N-m/41 ft-lbs.
2
29
7
28
27
G1_OM_Seated Row Rev.1.1.indd 18-19 11/19/13 4:29 PM
Page 11
20 21
ASSEMBLY
STEP 2 | BOTTOM PAD ASSEMBLY INSTRUCTIONS & NOTES
PART 3: PAD ASSEMBLY
ID DESCRIPTION QUANTITY
30 Bottom Pad 1
31 M10 X 20L Hex Bolt 4
Install the pad as shown.
Tighten to 57 N-m/41 ft-lbs.
31
30
STEP 1 | FOOT REST ASSEMBLY ASSEMBLY INSTRUCTIONS & NOTES
PART 4: FOOT REST ASSEMBLY
ID DESCRIPTION QUANTITY
2 M10 Flat Washer 4
5 M10 Nylock Nut 2
32 Foot Rest 1
33 M10 X 80L SHC 2
ASSEMBLY
5
2
33
32
Torque hardware to: 77 N-m/57 ft-lbs.
G1_OM_Seated Row Rev.1.1.indd 20-21 11/19/13 4:29 PM
Page 12
22 23
STEP 1 | SHROUD ASSEMBLY ASSEMBLY INSTRUCTIONS & NOTES
PART 5: PLASTICS ASSEMBLY
ID DESCRIPTION QUANTITY
34 Front Shroud 1
35 Rear Shroud (Not shown) 1
ASSEMBLY
Install the weight stack shrouds as shown.
34
Position hangers in their lowest position
STEP 2 | TOP CAP ASSEMBLY INSTRUCTIONS & NOTES
ID DESCRIPTION QUANTITY
36 M8 X 25L SHC 4
37 M8 Flat Washer (20 mm diameter) 4
38 Top Cap 1
37
36
38
ASSEMBLY
PART 5: PLASTICS ASSEMBLY
Install the top cap onto the weight stack as shown.
Torque to 17 N-m/147 in-lbs.
Position top cap so that the instructional placard faces the user.
G1_OM_Seated Row Rev.1.1.indd 22-23 11/19/13 4:29 PM
Page 13
24 25
STEP 3 | TOP CAP COVERS INSTRUCTIONS & NOTES
ID DESCRIPTION QUANTITY
39 Top Cap Cover 2
39
39
ASSEMBLY
PART 5: PLASTICS ASSEMBLY
Install the top cap covers.
STEP 1 | CABLE ADJUSTMENT INSTRUCTIONS & NOTES
ASSEMBLY
PART 6: CABLE ADJUSTMENT
Cable tension is adjusted by raising or lowering pulley as shown.
Note: Nuts for adjustable pulley must be on inside towards weight plates.
G1_OM_Seated Row Rev.1.1.indd 24-25 11/19/13 4:29 PM
Page 14
26 27
ASSEMBLY
PART 7: PREMIUM KIT ASSEMBLY
PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
ID DESCRIPTION QUANTITY
1P Wing 1
2P Rep Counter 1
3P Towel Hook 1
4P Premium Grip Assembly 2
5P Premium Pullpin 2
6P Seat Assist Gas Shock 1
7P M10 Nylock Nut (Not shown) 1
4P
3P6P1P
5P
2P
STEP 1 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
PART 7: PREMIUM KIT ASSEMBLY
1. Remove the (2) top cap covers using a flat blade screw
driver.
2. Remove the (4) M8 bolts and 20 mm diameter washers
that hold the top cap to the weight stack frame.
3. Remove top cap and rear shroud.
4. Assemble the Repetition Counter magnet holder
to the headplate using the M5 X 12L bolt and M5
washer provided with the kit.
Top cap covers, 20 mm diameter washers &
M8 screws can be discarded
Holder must be mounted on thes
same side of the weight stack as
Rep Counter
Rep Counter - Magnet
ASSEMBLY
G1_OM_Seated Row Rev.1.1.indd 26-27 11/19/13 4:29 PM
Page 15
28 29
ASSEMBLY
STEP 2 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
PART 7: PREMIUM KIT ASSEMBLY
Rep Counter - Sensors
1. Assemble Rep Counter sensor base using (4)
screws included with the kit.
2. Assemble (3) sensors located per machine chart
shown below.
Route wires in groove
Thread zip ties through
holes to secure cables
STEP 3 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
PART 7: PREMIUM KIT ASSEMBLY
1. Remove and discard hole caps using caution not
to scratch the paint.
2. Attach plug to Rep Counter.
3. Assemble Towel Hook (3P) and Rep Counter
(2P) using the M8 X 35L SHC bolts provided.
4. Torque bolts to 17 N-m/147 in-lbs.
Rep Counter wires must be
routed through the center of
the Towel Hook
Rep Counter
ASSEMBLY
Machine Sensor Locations (Sensor “A” = Top, “B” = Middle, “C” = Bottom)
Chest Press A2, B7, C13
Shoulder Press A1, B4, C13
Leg Extension A1, B7, C13
Seated Leg Curl A6, B10, C13
Leg Press A6, B10, C13
Lat Pulldown A1, B3, C13
Triceps Press A5, B8, C13
Seated Row A1, B4, C13
Bicep Curl A6, B8, C13
Hip Add/Abduction A7, B11, C13
Pec Fly/Rear Delt A7,B 9, C13
Abdominal A8, B10, C13
Back Extension A6, B8, C13
Glute A2, B7, C13
G1_OM_Seated Row Rev.1.1.indd 28-29 11/19/13 4:29 PM
Page 16
30 31
ASSEMBLY
STEP 4 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
PART 7: PREMIUM KIT ASSEMBLY
Assemble the wing (1P) as shown M8 hardware
provided with the kit. Tighten to 39N-m (29 ftlbs.).
Wing
STEP 5 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
PART 7: PREMIUM KIT ASSEMBLY
Grips
ASSEMBLY
1. Pin headplate to create slack in the cable.
2. Unscrew M5 bolt to disassemble grip.
3. Remove pin and clevis from cable.
4. Remove bullet cover.
1
2
3
4
5
6
5. Slide premium grip over cable, insert cable onto
clevis and assemble using existing M5 hardware.
6. Assemble plug.
7. Unpin headplate.
G1_OM_Seated Row Rev.1.1.indd 30-31 11/19/13 4:29 PM
Page 17
32 33
ASSEMBLY
STEP 6 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
PART 7: PREMIUM KIT ASSEMBLY
Pull Pin
Remove the two pull pins using an adjustable wrench, and replace with the Premium
pull pins making sure that the pull pin lengths are correct for each location. (5P).
STEP 7 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
PART 7: PREMIUM KIT ASSEMBLY
ASSEMBLY
Gas Shock
Raise the seat to the highest position before adding
gas shock (6P)
Shock must be positioned as shown with gas cylinder
above piston rod
1
3
2
4
5
Disassembly and assembly for both
ends of shock (Only one end is
shown)
G1_OM_Seated Row Rev.1.1.indd 32-33 11/19/13 4:29 PM
Page 18
G1_OM_Seated Row Rev.1.1.indd 34-35 11/19/13 4:29 PM
Page 19
Matrix Fitness
1600 Landmark Drive
Cottage Grove WI 53527
matrixfitness.com
Toll-free 866.693.4863
Facsimilie 608.839.8687
Versa Seated Row Owners Guide Rev.1.1 Copyright © 2013 Matrix Fitness
G1_OM_Seated Row Rev.1.1.indd 36 11/19/13 4:29 PM
Loading...