OWNERS MANUAL
Versa Single-Station Strength
VS-S13 Converging Chest Press
Table Of Contents
Safety, General Care & Maintenence ...............................................................3
Getting Started (Product Specifications) ........................................................5
Assembly Information ....................................................................................... 6
Markings ...............................................................................................................7
Parts List ..............................................................................................................8
Installation & Assembly: Value Line
Part 1 Weight Stack Assembly .................................................................10
Part 2 Arm Assembly ................................................................................ 11
Part 3 Cable Assembly ..............................................................................13
Part 4 Seat Pad Assembly ........................................................................ 17
Part 5 Plastics Assembly ..........................................................................19
Installation & Assembly: Optional Kits
Part 6 Premium Kit Assembly ................................................................. 22
Part 7 Short User Ki ................................................................................. 30
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
It is the sole responsibility of the purchaser of Matrix products to instruct all individuals, whether they are the end user or supervising personnel on proper usage of the equipment.
It is recommended that all users of Matrix exercise equipment be informed of the following information prior to its use.
PROPER USAGE
Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that Matrix equipment
be used properly to avoid injury.
Keep hands and feet clear at all times from moving parts to avoid injury.
CHECK FOR DAMAGED PARTS
1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by your
country’s local Matrix dealer.
. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important information.
2
If unreadable or missing, contact your Matrix dealer for a replacement.
3. SECURING EQUIPMENT: Manufacturer recommends that all stationary MATRIX strength equipment be secured to the floor
to stabilize equipment and eliminate rocking or tipping over. This must be performed by a licensed contractor.
All anchor points must be able to withstand 750 lbs. (3.3 kN) pull-out force.
4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping your
li-ability to a minimum. Equipment needs to be inspected at regular intervals.
5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. Matrix
dealers will provide service and maintenance training at our corporate facility upon request.
3
IMPORTANT SAFETY INSTRUCTIONS
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW
THESE PRECAUTIONS TO AVOID INJURY!
1. Never allow children on strength training equipment. Teenagers must be supervised at all times while using this
equipment.
2. All warnings and instructions should be read and proper instruction obtained prior to use.
3. Use this equipment for its intended purposes only.
4. NEVER allow resistance straps, ropes or other means be attached to this equipment, as this may result in serious
injury.
5. NEVER use this equipment for support during stretching, as this may result in serious injury.
6. Cease exercise if you feel faint or dizzy. Obtain a medical exam before beginning an exercise program.
7. Keep body, hair, clothing and accessories free and clear of all moving parts.
8. Inspect the machine before use. DO NOT use machine if it appears damaged or inoperable.
9. Check to see that the selector pin is completely inserted into the weight stack.
10. NEVER use this machine with the weight stack pinned in an elevated position.
11. NEVER use dumbells or other means to incrementally increase the weight resistance. Only use the means provided
directly from the manufacturer.
12. This equipment should only be used in supervised areas where access and control are regulated by the owner.
4
EXERCISE PLACARD
PRODUCT SPECIFICATIONS
GETTING STARTED
EXERCISE PLACARD | PRODUCT SPECIFICATIONS | MAINTENANCE CHECKLIST
MAINTENANCE CHECKLIST
ACTION FREQUENCY
Clean Upholstery Daily
Inspect Cables Daily
Clean Guide Rods Monthly
Inspect Hardware Monthly
Inspect Frame Bi-Annually
Clean Machine As Needed
Clean Grips As Needed
Lubricate Guide Rods As Needed
Upholstery & Grips should be cleaned with a non-ammonia based cleaner or a mild soap and water. Guide rods should be
lubricated with Teflon based lubricant. Apply the lubricant to a cotton cloth and then apply up and down the guide rods.
5
ASSEMBLY
UNPACKING | TOOLS REQUIRED
UNPACKING
Thank you for purchasing a Matrix product. This machine is an EN957-1 and EN957-2 compliant Class S product. Your Matrix product is inspected before it is packaged. It is shipped in multiple pieces to facilitate the compact packaging of the
machine. Prior to assembly, confirm all the components by matching them with the exploded diagrams. Carefully unpack
the unit from this box and dispose of the packing materials in accordance with your local laws.
CAUTION
The weight of the product is 378 lbs. (172 kg) not including the weight stack. The standard weight stack for this machine is
160 lbs. (73 kg) & the heavy stack is 230 lbs. (104kg). To avoid injury to yourself and prevent damage to the frame components, be sure to have proper assistance removing the frame pieces from this box. Please be sure to install the equipment
on a stable base, properly level the machine and leave at least two feet of clearance to enter and exit the machine. Maximum user weight for this machine is 300 lbs.
TOOLS REQUIRED FOR ASSEMBLY
3MM L-Shaped Allen Wrench
4MM L-Shaped Allen Wrench
5MM L-Shaped Allen Wrench
6MM L-Shaped Allen Wrench
8MM L-Shaped Allen Wrench
10MM L-Shaped Allen Wrench
Phillips & Standard Screwdrivers
8MM Open-End Wrench
13MM Open-End Wrench
17MM Open-End Wrench.
19MM Open-End Wrench
Adjustable Wrench
Blue Locktite 242 must be used on all fasteners that are not assembled with
Nylock Nuts
6
MARKINGS
WARNING LABEL LOCATIONS
7
Parts List
ID DESCRIPTION QTY
1 M10 X 105L Socket Head Cap Screw 2
2 M10 Flat Washer 30
3 Narrow Cupped Flange 1
4 M10 Nylock Nut 10
5 Upper Connecting Tube 1
6 M10 X 20L Socket Head Cap Screw 6
7 Weight Stack Frame 1
8 User Frame 1
9 M10 X 125 Socket Hear Cap Screw 2
10 Wide Cupped Flange 1
11 Lower Connecting Tube 4
12 Right Arm Assembly 2
13 Left Arm Assembly 1
14 Flat Washer (Ø40 mm) 4
15 Belleville Washer 2
16 M10 X 30L Socket Head Cap Screw 2
17 Ø20mm Shaft 2
18 M12 X 25L Socket Head Cap Screw 2
19 M12 Flat Washer 2
20 Pulley 8
21 Stack Cable 1
22 M10 X 50L Socket Head Cap Screw 5
23 M10 X 75L Socket Head Cap Screw 5
24 Floating Pulley Bracket 2
25 M8 X 50L Socket Head Cap Screw 3
26 Spacer 6
27 Cable Tie Rod End 3
28 M8 Flat Washer 6
29 M8 Nylock Nut 3
30 User Frame Cable 1
31 Head Pad 1
32 Back Pad 1
33 M10 X 20L Hex Bolt 4
8
34 Bottom Pad 1
Parts List
ID
35
36
37
38
39
40
1P
2P
3P
4P
5P
6P
7P
DESCRIPTION QTY
Front Shroud 1
Rear Shroud 1
M8 X 25L SHC
M8 Flat Washer (Ø20 mm) 4
Top Cap 1
Top Cap Cover 2
OPTIONAL PREMIUM KIT COMPONENTS
Wing 1
Rep Counter 1
Towel Hook 1
ASG Push Grip 2
Premium Pullpin 1
Seat Assist Gas Shock 1
M10 Nylock Nut 1
4
1SK
2SK
3SK
OPTIONAL SHORT USER KIT
Foot Rest 1
M10 Flat Washer 2
M10 X 25L SHC 2
9
PART 1: WEIGHT STACK TO USER FRAME ASSEMBLY
6
5
4
11
8
3
10
9
2
1
7
STEP 1 | WEIGHT STACK TO USER FRAME INSTRUCTIONS & NOTES
ID DESCRIPTION QUANTITY
1 M10 X 105L SHC 2
2 M10 Flat Washer 14
3 Narrow Cupped Flange 1
4 M10 Nylock Nut 4
5 Upper Connecting Tube 1
6 M10 X 20L SHC 6
7 Weight Stack frame 1
8 User Frame 1
9 M10 X 125L SHC 2
10 Wide Cupped Flange 1
11 Lower Connecting Tube 1
ASSEMBLY
Fully tighten hardware to 77 N-m/57 ft-lbs. after weightplates have been assembled
10
STEP 1 | RIGHT & LEFT ARM ASSEMBLY INSTRUCTIONS & NOTES
14
17
12
15
13
14
16
14
171516
ID DESCRIPTION QUANTITY
12 Right Arm Assembly 1
13 Left Arm Assembly 1
14 40mm Diameter Washer 4
15 Belleville (Spring) Washer 2
16 M10 X 30L SHC 2
17 20 mm Diameter Shaft 2
Attach the arms to the frame using the hardware shown, but DO NOT FULLY TIGHTEN
ASSEMBLY
PART 2: ARM ASSEMBLY
Belleville washer item 15 must be assembled with inner (convex) diameter contacting the bearing.
The outer diameter and concave side of Belleville washer contacts the outer washer item 14.
11
STEP 2 | RIGHT & LEFT ARM ASSEMBLY INSTRUCTIONS & NOTES
19
18
ID DESCRIPTION QUANTITY
18 M12 X 25L SHC 2
19 M12 Flat Washer 2
ASSEMBLY
PART 2: ARM ASSEMBLY
Install the pivot cap screw as shown. Torque all arm hardware to:
• M10 from step 1 to 77 N-m/57 ft-lbs.
• M12 from step 2 to 136 N-m/100 ft-lbs.
12
STEP 1 | WEIGHT STACK CABLE ASSEMBLY INSTRUCTIONS & NOTES
2142
24
20
22
23
ID DESCRIPTION QUANTITY
2 M10 Flat Washer 6
4 M10 Nylock Nut 3
20 Pulley 5
21 Stack Cable 1
22 M10 X 50L SHC 2
23 M10 X 75L SHC 1
24 Floating Pulley Plate 2
ASSEMBLY
PART 3: CABLE ASSEMBLY
View A
Cable tension is adjusted by raising or lowering pulley as shown in View A.
Note: Nuts for adjustable pulley must be on inside towards weight plates.
13
PART 3: CABLE ASSEMBLY
29
28
25
26
27
STEP 2 | WEIGHT STACK CABLE ASSEMBLY INSTRUCTIONS & NOTES
ID DESCRIPTION QUANTITY
25 M8 X 50L SHC 1
26 Spacer 2
27 Cable Tie Rod End 1
28 M8 Flat Washer 2
29 M8 Nylock Nut 1
ASSEMBLY
Fully thread cable bolt into tie-rod, then attach to frame.
Torque item 25 to: 39 N-m/29 ft-lbs.
14
STEP 3 | USER FRAME CABLE ASSEMBLY INSTRUCTIONS & NOTES
30
20
4
2
22
ID DESCRIPTION QUANTITY
2 M10 Washer 6
4 M10 Nylock Nut 3
20 Pulley 3
22 M10 X 50L SHC 3
30 User Frame Cable 1
ASSEMBLY
PART 3: CABLE ASSEMBLY
Install the secondary cable pulleys as shown.
Torque hardware to: 77 N-m/57 ft-lbs.
15
ASSEMBLY
29
28
26
27
25
PART 3: CABLE ASSEMBLY
STEP 4 | USER FRAME CABLE ASSEMBLY INSTRUCTIONS & NOTES
ID DESCRIPTION QUANTITY
25 M8 X 50L SHC 2
26 Spacer 4
27 Cable Tie Rod End 2
28 M8 Flat Washer 4
29 M8 Nylock Nut 2
*Note: Image shows left arm assembly only, though quantities reflect both left and right arm assemblies.
Fully thread cable bolt into tie-rod, then attach to frame.
Torque item 31 to: 39 N-m/29 ft-lbs.
16
32
31
2
23
ASSEMBLY
PART 4: SEAT PAD ASSEMBLY
STEP 1 | BACK PAD AND HEAD PAD ASSEMBLY INSTRUCTIONS & NOTES
ID DESCRIPTION QUANTITY
2 M10 Flat Washer 4
23 M10 X 75L SHC 4
31 Head Pad 1
32 Back Pad 1
Install the head & back pads as shown.
Torque to 57 N-m/41 ft-lbs.
17
STEP 2 | BOTTOM PAD ASSEMBLY INSTRUCTIONS & NOTES
33
34
33
34
ID DESCRIPTION QUANTITY
33 M10 X 20L Hex Bolt 4
34 Bottom Pad 1
ASSEMBLY
PART 4: SEAT PAD ASSEMBLY
Install the seat pads as shown.
Torque to 57 N-m/41 ft-lbs.
18
STEP 1 | SHROUD ASSEMBLY ASSEMBLY INSTRUCTIONS & NOTES
35
ID DESCRIPTION QUANTITY
35 Front Shroud 1
36 Rear Shroud (Not shown) 1
Position hangers in their lowest position
ASSEMBLY
PART 5: PLASTICS ASSEMBLY
Install the weight stack shrouds as shown.
19
STEP 2 | TOP CAP ASSEMBLY INSTRUCTIONS & NOTES
38
37
39
38
37
39
ID DESCRIPTION QUANTITY
37 M8 X 25L SHC 4
38 M8 Flat Washer (20 mm diameter) 4
39 Top Cap 1
ASSEMBLY
PART 5: PLASTICS ASSEMBLY
Install the top cap onto the weight stack as shown.
Torque to 17 N-m/147 in-lbs.
Position top cap so that the instructional placard faces the user.
20
STEP 3 | TOP CAP COVERS INSTRUCTIONS & NOTES
40
40
ID DESCRIPTION QUANTITY
40 Top Cap Cover 2
ASSEMBLY
PART 5: PLASTICS ASSEMBLY
Install the top cap covers.
21
OPTIONAL PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
2P
3P
1P
6P
5P
4P
ID DESCRIPTION QUANTITY
1P Wing 1
2P Rep Counter 1
3P Towel Hook 1
4P ASG Push Grip 2
5P Premium Pullpin 1
6P Seat Assist Gas Shock 1
7P M10 Nylock Nut (Not Shown) 1
ASSEMBLY
PART 6: PREMIUM KIT ASSEMBLY
IMPORTANT NOTICE
PLEASE NOTE:
Be sure to remove the insulating
sheet when installing the
Rep Counter.
22
STEP 1 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
Rep Counter - Magnet
1. Remove the (2) top cap covers using a flat blade screw
driver.
2. Remove the (4) M8 bolts and 20 mm diameter washers
that hold the top cap to the weight stack frame.
Top cap covers, 20 mm diameter washers &
M8 screws can be discarded
ASSEMBLY
PART 6: PREMIUM KIT ASSEMBLY
3. Remove top cap and rear shroud.
4. Assemble the Repetition Counter magnet holder
to the headplate using the M5 X 12L bolt and M5
washer provided with the kit.
Holder must be mounted on the same
side of the weight stack as Rep Counter
23
ASSEMBLY
PART 6: PREMIUM KIT ASSEMBLY
STEP 2 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
Rep Counter - Sensors
1. Assemble Rep Counter sensor base using (4)
screws included with the kit.
2. Assemble (3) sensors located per machine chart
shown below.
Thread zip ties through
holes to secure cables
Route wires in groove
24
Machine Sensor Locations (Sensor “A” = Top, “B” = Middle, “C” = Bottom)
Chest Press A2, B7, C13
Shoulder Press A1, B4, C13
Leg Extension A1, B7, C13
Seated Leg Curl A6, B10, C13
Leg Press A6, B10, C13
Lat Pulldown A1, B3, C13
Triceps Press A5, B8, C13
Seated Row A1, B4, C13
Bicep Curl A6, B8, C13
Hip Add/Abduction A7, B11, C13
Pec Fly/Rear Delt A7,B 9, C13
Abdominal A8, B10, C13
Back Extension A6, B8, C13
Glute A2, B7, C13
ASSEMBLY
PART 6: PREMIUM KIT ASSEMBLY
STEP 3 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
Rep Counter
1. Remove and discard hole caps using caution not
to scratch the paint.
2. Attach plug to Rep Counter.
3. Assemble Towel Hook (3P) and Rep Counter
(2P) using the M8 X 35L SHC bolts provided.
Rep Counter wires must be
routed through the center of
the Towel Hook
4. Torque bolts to 17 N-m/147 in-lbs.
25
STEP 4 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
Wing
Assemble the wing (1P) as shown using the M8
hardware provided with the kit. Tighten to 39N-m
(29 ft-lbs.).
ASSEMBLY
PART 6: PREMIUM KIT ASSEMBLY
26
7.6 Degrees
7.6 Degrees
ASSEMBLY
PART 6: PREMIUM KIT ASSEMBLY
STEP 5 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
ASG Grips
1. Remove the end caps using a 3 mm Allen wrench.
2. Cut off and discard the grips.
3. Remove inner collars with a 3 mm allen wrench.
4. Assemble the ASG grip (4P) as shown; lock inner collars using a 5 mm Allen wench (torque to 8 N-m/5
ft-lbs.), and a 3 mm Allen wrench to secure the end caps. 5. Orient ASG grips as shown, with the palm
portion rotated forward away from user 8 degrees.
27
ASSEMBLY
PART 6: PREMIUM KIT ASSEMBLY
STEP 6 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
Pull Pin
Remove the pull pin using an adjustable
wrench, and replace with the Premium
pull pin (5P).
28
ASSEMBLY
PART 6: PREMIUM KIT ASSEMBLY
STEP 7 | PREMIUM KIT ASSEMBLY INSTRUCTIONS & NOTES
Gas Shock
2
1
3
Raise the seat to the highest position before adding gas shock (6P)
4
5
Disassembly and assembly for both ends
of shock (Only one end is shown)
Shock must be positioned as shown with gas cylinder above piston rod
29
PART 7: SHORT USER KIT ASSEMBLY
1SK
2SK
3SK
OPTIONAL SHORT USER KIT ASSEMBLY INSTRUCTIONS & NOTES
ID DESCRIPTION QUANTITY
1SK Foot Rest 1
2SK M10 Flat Washer 2
3SK M10 X 20L SHC 2
ASSEMBLY
30
STEP 1 | SHORT USER KIT ASSEMBLY INSTRUCTIONS & NOTES
ASSEMBLY
PART 7: SHORT USER KIT ASSEMBLY
Assemble Short User Kit using the M10 hardware provided.
Torque hardware to: 77 N-m/57 ft-lbs.
31
Matrix Fitness
1600 Landmark Drive
Cottage Grove WI 53527
matrixfitness.com
Toll-free 866.693.4863
Facsimilie 608.839.8687
Versa Converging Chest Press Owners Guide Rev.1.3 Copyright © 2016 Matrix Fitness
Loading...