Page 1
OWNERS MANUAL
ULTRA Single-Station Strength
G7-S42 Triceps Press
Page 2
Table Of Contents
Safety, General Care & Maintenence ............................................................................................... 3
Getting Started (Product Specications) .......................................................................................... 5
Assembly Information ....................................................................................................................... 6
Parts List........................................................................................................................................... 7
Installation & Assembly: Value Line
Part 1 Weight Stack & User Frame Assembly ....................................................................... 9
Part 2 Seat Assembly ..........................................................................................................13
Part 3 Arm Assembly ........................................................................................................... 15
Part 4 Pad Assembly ...........................................................................................................20
Part 5 Plastics Assembly .....................................................................................................22
Page 3
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
It is the sole responsibility of the purchaser of Matrix products to instruct all individuals, whether they are the end user or
supervising personnel on proper usage of the equipment.
It is recommended that all users of Matrix exercise equipment be informed of the following information prior to its use.
PROPER USAGE
Do not use any equipment in any way other than designed or intended by the manufacturer. It is imperative that Matrix
equipment be used properly to avoid injury.
Keep hands and feet clear at all times from moving parts to avoid injury.
CHECK FOR DAMAGED PARTS
1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use only replacement parts supplied by
your country’s local Matrix dealer.
2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain important information.
If unreadable or missing, contact your Matrix dealer for a replacement.
3. SECURING EQUIPMENT: All equipment MUST be secured to the floor to stabilize and eliminate rocking or tipping over.
This must be performed by a licensed contractor.
4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well as keeping
your liability to a minimum. Equipment needs to be inspected at regular intervals.
5. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so.
Matrix dealers will provide service and maintenance training at our corporate facility upon request.
3
Page 4
IMPORTANT SAFETY INSTRUCTIONS
WARNING: This product contains chemicals known to the State of California
to cause cancer and birth defects or other reproductive harm.
WARNING: SERIOUS INJURY CAN OCCUR ON THIS EQUIPMENT. FOLLOW
THESE PRECAUTIONS TO AVOID INJURY!
1. Never allow children on strength training equipment. Teenagers must be supervised at all times while using this
equipment.
2. All warnings and instructions should be read and proper instruction obtained prior to use.
3. Use this equipment for its intended purposes only.
4. NEVER allow resistance straps, ropes or other means be attached to this equipment, as this may result in serious
injury.
5. NEVER use this equipment for support during stretching, as this may result in serious injury.
6. Cease exercise if you feel faint or dizzy. Obtain a medical exam before beginning an exercise program.
7. Keep body, hair, clothing and accessories free and clear of all moving parts.
8. Inspect the machine before use. DO NOT use machine if it appears damaged or inoperable.
9. Check to see that the selector pin is completely inserted into the weight stack.
10. NEVER use this machine with the weight stack pinned in an elevated position.
11. NEVER use dumbells or other means to incrementally increase the weight resistance. Only use the means provided
directly from the manufacturer.
12. This equipment should only be used in supervised areas where access and control are regulated by the owner.
4
Page 5
GETTING STARTED
EXERCISE PLACARD | PRODUCT SPECIFICATIONS | MAINTENANCE CHECKLIST
EXERCISE PLACARD
PRODUCT SPECIFICATIONS
TECH SPECS
Maximum User Weight 136 kg / 300 lbs.
Maximum Training Weight 109 kg / 240 lbs.
Product Weight 307 kg / 675 lbs.
Overall Dimensions (L x W x H) 155.4 x 106.8 x 129.6 cm / 61.2" x 42.1" x 51.0"
WARRANTY (Valid in USA only)
Frame (not coatings) 10 years
Weight stacks 5 years
Pulleys 5 years
Pivot bearings 5 years
Any items not specified 3 years
Labor (excluding upholstery/cables/grips) 3 years
Upholstery/cables/grips/springs 1 year
Accessories 6 months
MAINTENANCE CHECKLIST
ACTION FREQUENCY
Clean Upholstery Daily
Inspect Cables Daily
Clean Guide Rods Monthly
Inspect Hardware Monthly
Inspect Frame Bi-Annually
Clean Machine As Needed
Clean Grips As Needed
Lubricate Guide Rods As Needed
Upholstery & Grips should be cleaned with a non-ammonia based cleaner or a mild soap and water. Guide rods should be
lubricated with Teflon based lubricant. Apply the lubricant to a cotton cloth and then apply up and down the guide rods.
5
Page 6
ASSEMBLY
UNPACKING | TOOLS REQUIRED
UNPACKING
Thank you for purchasing a Matrix product. This machine is an EN957-1 and EN957-2 compliant Class S product. Your
Matrix product is inspected before it is packaged. It is shipped in multiple pieces to facilitate the compact packaging of the
machine. Prior to assembly, confirm all the components by matching them with the exploded diagrams. Carefully unpack
the unit from this box and dispose of the packing materials in accordance with your local laws.
CAUTION
The weight of the product is 675 lbs. (306 kg) not including the weight stack. The weight stack for this machine is 240
lbs. (109 kg). To avoid injury to yourself and prevent damage to the frame components, be sure to have proper assistance
removing the frame pieces from this box. Please be sure to install the equipment on a stable base, properly level the
machine and leave at least two feet of clearance to enter and exit the machine. Maximum user weight for this machine is
300 lbs.
TOOLS REQUIRED FOR ASSEMBLY
3MM L-Shaped Allen Wrench
4MM L-Shaped Allen Wrench
5MM L-Shaped Allen Wrench
6MM L-Shaped Allen Wrench
8MM L-Shaped Allen Wrench
10MM L-Shaped Allen Wrench
Phillips & Standard Screwdrivers
8MM Open-End Wrench
13MM Open-End Wrench
17MM Open-End Wrench.
19MM Open-End Wrench
Adjustable Wrench
Blue Locktite 242 must be used on all fasteners that are not assembled with Nylock Nuts.
6
Page 7
Parts List
ID
1 User Frame 1
2 Arm Axle 2
3 M10 Flat Washer 15
4 M10 X 75L Socket Head Cap Screw 4
5 Upper Connecting Tube 1
6 M10 Saddle Washer 6
7 M10 X 30L Hex Head Bolt 6
8 Lower Connecting Tube 1
9 Weight Stack 1
10 M10 Nylock Nut 9
11 M10 X 140L Socket Head Cap Screw 2
12 M10 X 45L Socket Head Cap Screw 1
13 Pulley 3
14 Cable 1
15 Large Pivot Cap 3
16 M10 X 50L Socket Head Cap Screw 1
17 M8 X 25L Socket Head Cap Screw 8
18 Medium Pivot Cap 8
DESCRIPTION
QTY
19 Seat Link 4
20 Axle 4
21 Spring 2
22 Seat 1
23 M10 X 15L Socket Head Cap Screw 2
24 Small Pivot Cap 2
25 Snap Ring 2
26 Right Arm 1
27 Wave (Spring) Washer 2
28 Left Arm 1
29 M8 Nylock Nut 6
30 M10 X 65L Socket Head Cap Screw Seat 1
31 M8 X 20 Socket Head Cap Screw 10
7
Page 8
Parts List
ID
32 M8 Flat Washer 16
33 Pulley Spacer 1
34 M5 Shoulder Bolt 1
35 M5 Nylock Nut 1
36 Counter Weight 2
37 M8 X 30L Special Screw 2
38 Sleeve 2
39 Handlebar 2
40 M10 X 75L Button Head Cap Screw 2
41 Back Pad Assembly 1
42 Pad 1
43 M10 X 20L Hex Bolt 4
44 Left Front Shroud 1
45 Right Front Shroud 1
46 Rear Shroud 1
47 M8 X 60L Socket Head Cap Screw 4
48 Top Cap 1
DESCRIPTION
QTY
8
Page 9
STEP 1 | USER FRAME INSTRUCTIONS & NOTES
2
1
ID DESCRIPTION QUANITY
1 User Frame 1
2 Arm Axle 2
ASSEMBLY
PART 1: USER FRAME ASSEMBLY
• Apply red Loctite 262 to axle threads and fully tighten.
9
Page 10
9
3
4
5
8
7
6
STEP 2 | USER FRAME INSTRUCTIONS & NOTES
ID DESCRIPTION QUANITY
3 M10 Flat Washer 8
4 M10 X 75L SHC 4
5 Upper Connecting Tube 1
6 M10 Saddle Washer 2
7 M10 X 30L SHC 6
8 Lower Connecting Tube 1
9 Weight Stack 1
ASSEMBLY
PART 1: USER FRAME ASSEMBLY
View A
10
• Ensure that the user frame and weight stack are level
with all oor pads contacting the oor equally,
• Torque all M10 Frame Hardware to: 77 N-m/57 ft-lbs
• Orient the saddle washers as shown in View A
Page 11
STEP 3 | WEIGHT STACK CABLE INSTRUCTIONS & NOTES
11
1063
10
ID DESCRIPTION QUANITY
3 M10 Flat Washer 4
6 M10 Saddle Washer 4
10 M10 Nylock Nut 6
11 M10 X 140L SHC 2
ASSEMBLY
PART 1: USER FRAME ASSEMBLY
View A
• Torque all to: 77 N-m/57 ft-lbs.
• Orient the saddle washers as shown in View A
11
Page 12
10
3
16
12
15
13
14
STEP 4 | CABLE ASSEMBLY INSTRUCTIONS & NOTES
ID DESCRIPTION QUANITY
3 M10 Flat Washer 3
10 M10 Nylock Nut 2
12 M10 X 45 SHC 1
13 Pulley 2
14 Cable 1
15 Large Pivot Cap 1
16 M10 X 50 SHC 1
ASSEMBLY
PART 1: USER FRAME ASSEMBLY
12
Page 13
STEP 1 | SEAT LINK ASSEMBLY INSTRUCTIONS & NOTES
17
18
19
20
21
26
ID DESCRIPTION QUANITY
17 M8 X 25L SHC 2
18 Medium Pivot Cap 2
19 Seat Link 1
20 Axle 2
21 Spring 1
22 Seat 1
ASSEMBLY
PART 2: SEAT ASSEMBLY
*Note: Shoulder
Press seat assembly
is shown - but steps
and components
are identical for the
Triceps Press
Tighten to 39 N-m/29 ft-lbs.
Ensure bottom links are assembled correctly by
testing spring tension
Outer tab of spring must be secured behind
frame reaction bar
13
Page 14
STEP 2 | SEAT ASSEMBLY INSTRUCTIONS & NOTES
ID DESCRIPTION QUANITY
17 M8 X 25L SHC 6
18 Medium Pivot Cap 6
19 Seat Link 3
20 Axle 2
21 Spring 1
ASSEMBLY
PART 2: SEAT ASSEMBLY
Rotate seat to
engage pull pin
Assemble upper
axles, links and
pivot caps
14
Tighten to 39 N-m/29 ft-lbs.
Page 15
STEP 1 | LEFT AND RIGHT* ARM ASSEMBLY INSTRUCTIONS & NOTES
28
26
27
25
24
23
ID DESCRIPTION QUANITY
23 M10 X15L SHC 2
24 Small Pivot Cap 2
25 Snap Ring 2
26 Right Arm 1
27 Wave (Spring) Washer 2
28 Left Arm 1
*Only right arm assembly is shown
Apply blue Loctite 242 and tighten to 77 N-m/57 ft-lbs.
ASSEMBLY
PART 3: ARM ASSEMBLY
15
Page 16
32
31
14
13
33
15
30
29
10
STEP 2 | PULLEY ASSEMBLY INSTRUCTIONS & NOTES
ID DESCRIPTION QUANITY
10 M10 Nylock Nut 1
13 Pulley 1
14 Cable 1
15 Large Pivot Cap 2
29 M8 Nylock Nut 6
30 M10 X 65L SHC 1
31 M8 X 20L SHC 6
32 M8 Flat Washer 12
33 Pulley Spacer 1
ASSEMBLY
PART 3: ARM ASSEMBLY
Torque M8s to: 39 N-m/29 ft-lbs.
Torque M10 to 77 N-m/57 ft-lbs.
16
Page 17
STEP 3| CABLE ASSEMBLY INSTRUCTIONS & NOTES
35
34
ID DESCRIPTION QUANITY
34 M5 Shoulder Bolt 1
35 M5 Nylock Nut 1
Raise arms up to attach cable end and torque to
16 N-m/142 in-lbs.
ASSEMBLY
PART 3: ARM ASSEMBLY
17
Page 18
STEP 4 | COUNTER WEIGHT ASSEMBLY INSTRUCTIONS & NOTES
31
32
36
ID DESCRIPTION QUANITY
31 M8 X 20L SHC 4
32 M8 Flat Washer 4
36 Counter Weight 2
ASSEMBLY
PART 3: ARM ASSEMBLY
Torque to: 39 N-m/29 ft-lbs.
18
Page 19
STEP 5 | HANDLEBAR ASSEMBLY INSTRUCTIONS & NOTES
38
37
39
ID DESCRIPTION QUANITY
37 M8 X 30L Special Screw 2
38 Sleeve 2
39 Handlebar 2
*Only right arm assembly is shown
ASSEMBLY
PART 3: ARM ASSEMBLY
Torque to: 39 N-m/29 ft-lbs.
19
Page 20
STEP 1 | BACK PAD ASSEMBLY INSTRUCTIONS & NOTES
41
40
ID DESCRIPTION QUANITY
40 M10 X 75L BHC 2
41 Back Pad Assembly 1
ASSEMBLY
PART 4: PAD ASSEMBLY
Install the pad as shown.
Tighten to 27 N-m/20 ft-lbs.
20
Page 21
STEP 2 | BOTTOM PAD ASSEMBLY INSTRUCTIONS & NOTES
42
43
ID DESCRIPTION QUANITY
42 Pad 1
43 M10 X 20L Hex Bolt 4
ASSEMBLY
PART 4: PAD ASSEMBLY
Install the pad as shown.
Tighten to 27 N-m/20 ft-lbs.
21
Page 22
STEP 1 | SHROUD ASSEMBLY ASSEMBLY INSTRUCTIONS & NOTES
46
45
44
ID DESCRIPTION QUANITY
44 Left Front Shroud 1
45 Right Front Shroud 1
46 Rear Shroud 1
ASSEMBLY
PART 5: PLASTICS ASSEMBLY
Install the weight stack shrouds as shown.
22
Page 23
STEP 2 | TOP CAP ASSEMBLY INSTRUCTIONS & NOTES
47
48
ID DESCRIPTION QUANITY
47 M8 X 60L SHC 4
48 Top Cap 1
Install the top cap and connect rep counter plug as shown.
Torque to 17 N-m/147 in-lbs.
ASSEMBLY
PART 5: PLASTICS ASSEMBLY
Position top cap so Rep Counter faces the user.
IMPORTANT NOTICE
PLEASE NOTE:
Be sure to remove the insulating
sheet when installing the
Rep Counter.
23
Page 24
Matrix Fitness
1600 Landmark Drive
Cottage Grove WI 53527
matrixfitness.com
Toll-free 866.693.4863
Facsimilie 608.839.8687
ULTRA Triceps Press Owners Guide rev.1.2 Copyright© 2014 Matrix Fitness
Loading...