How it Works
Matrix
Loading...
U5x-05
Service Manual
73 pgs8.26 Mb0

Matrix U5x-05 Service Manual

U5X-05 BIKE
SERVICE MANUAL
TABLE OF CONTENTS
CHAPTER 1: SERIAL NUMBER LOCATION ................................................................... 1
CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS
2.1 Read and Save These Instructions ........................................................................... 3
2.2 Electrical Requirements ............................................................................................ 4
CHAPTER 3: PREVENTATIVE MAINTENANCE
3.1 Recommended Cleaning Tips ................................................................................... 5
3.2 Check for Damaged Parts ......................................................................................... 5
3.3 Care and Maintenance Instructions .......................................................................... 6
CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION
4.1 Console Description .................................................................................................. 7
4.2 Workout Setup Steps - Manual .................................................................................. 8
4.3 Workout Setup Steps - Fat Burn ................................................................................ 8
4.4 Workout Setup Steps - Level Based .......................................................................... 8
4.5 Workout Setup Steps - Fitness Test ........................................................................... 9
CHAPTER 5: MANAGER MODE
5.1 Using Manager Mode ................................................................................................ 11
5.2 Manager Mode Overview ........................................................................................... 11
CHAPTER 6: ENGINEERING MODE
CHAPTER 7: SERVICE MODE
CHAPTER 8: TROUBLESHOOTING
8.1 Electrical Diagram ...................................................................................................... 14
8.2 LCB LED Indicators .................................................................................................... 19
8.3 Troubleshooting - Error 04A0 / 0440 .......................................................................... 20
8.4 Troubleshooting - Error 04B0 ...................................................................................... 21
8.5 Troubleshooting - Error 0248 ...................................................................................... 22
8.6 Troubleshooting - Error 0247 ...................................................................................... 23
8.7 Troubleshooting - Error 02B4 / 03A8 / 02AB / 0441 ................................................... 23
8.8 Troubleshooting - Error 01AC / 01AF ......................................................................... 24
8.9 Troubleshooting - Error 01B4 ...................................................................................... 25
TABLE OF CONTENTS
CHAPTER 9: PART REPLACEMENT GUIDE
9.1 Console Replacement ..................................................................................................... 30
9.2 Cup Holder Replacement .............................................................................................. 31
9.3 Handlebar Replacement ................................................................................................ 32
9.4 Handlebar Service ........................................................................................................... 33
9.5 Console Keypad / Overlay Replacement ....................................................................... 34
9.6 Pedal Replacement ......................................................................................................... 36
9.7 Crank Axle Set Replacement .......................................................................................... 37
9.8
9.9 Side Covers Replacement .............................................................................................. 39
9.10 Console Mast Replacement............................................................................................ 40
9.11 Seat Pad Replacement ................................................................................................... 41
9.12 Seat Post Replacement .................................................................................................. 42
9.13 Lower Control Board Replacement ............................................................................... 43
9.14 Battery Replacement ...................................................................................................... 44
9.15 Drive Belt Replacement .................................................................................................. 45
9.16 Generator Replacement .................................................................................................. 46
9.17 Rear Stabilizer Replacement .......................................................................................... 47
9.18 Front Stabilizer Replacement ......................................................................................... 48
9.19 Drive Axle Set Replacement ........................................................................................... 49
9.20 Testing the Bike ............................................................................................................... 53
Front Shrouds Replacement ........................................................................................... 38
CHAPTER 10: BIKE SPECIFICATIONS AND ASSEMBLY GUIDE
CHAPTER 11: SOFTWARE UPGRADE GUIDE
III
1.1 SERIAL NUMBER LOCATION
CHAPTER 1: SERIAL NUMBER LOCATION
FRAME SERIAL NUMBER LOCATION
1
1.1 SERIAL NUMBER LOCATION
CHAPTER 1: SERIAL NUMBER LOCATION
CONSOLE SERIAL NUMBER LOCATION
2
SN # PLACEMENT
CHAPTER 2: IMPORTANT SAFETY INSTRUCTIONS
2.1 READ AND SAVE THESE INSTRUCTIONS
To ensure your safety and protect the equipment, read all instructions before operating the MATRIX U5x-05 Bike.
To ensure proper use of the Matrix U5x-05 Bike, make sure that all users read this manual. Remind the users that before undertaking any fitness program, they should obtain complete physical examinations from their physicians. If, at any time while exercising, the user experiences dizziness, pain, or shortness of breath, nausea or feels faint, he or she must stop immediately.
* This bike is only to be used for its intended purpose described in this manual. Do not use attachments that have not been recommended by Matrix.
* Never drop or insert objects into any opening. Keep hands away from moving parts. If the item cannot be reached, contact a Matrix authorized dealer for assistance.
* Never operate the unit if it is damaged, not working properly, when it has been dropped, or has been in water.
* Keep hands and feet clear at all times from moving parts to avoid injury.
* Do not use this product outdoors, near swimming pools or in areas of high humidity.
* Do not operate where aerosol (spray) products are being used or when oxygen is being administered.
* Do not use this product in bare feet. Do not wear shoes with heels, leather soles, cleats, or spikes while exercising.
CAUTION! If you experience chest pains, nausea, dizziness, or shortness of breath, stop exercising immediately and con sult your physician before continuing.
CAUTION! Any changes or modifications to this equipment could void the product warranty.
-
* Do not remove the side covers. Service should only be done by an authorized service technician.
* Close supervision is necessary when used near children, invalids, or disabled people.
* When the bike is in use, young children and pets should be kept at least 3 meters / 10 feet away.
* Assemble and operate the bike on a solid, level surface.
* Never face backward while using the Matrix U5x-05 Bike.
* Use the stationary handlebars when mounting or dismounting the bike.
* Do not wear clothing that might catch on any moving parts of this bike.
3
CHAPTER 2: IMPORTANT SAFETY INFORMATION
2.2 ELECTRICAL REQUIREMENTS
110 V UNITS All Matrix 3x, 5x, 7xe and 7xi 110 V bikes require the use of a 100-125 V, 60 Hz and a 15 A “Dedicated Circuit”, with a non-looped (isolated) neutral/ground for power. This outlet should be a NEMA 5-15R and have the same configuration as the plug. No adapter should be used with this product. These bikes can be daisy-chained together with up to 4 units per 15 A dedicated circuit. Matrix daisy-chain cord adapters are sold separately.
220 V UNITS All Matrix 3x, 5x, 7xe and 7xi 220 V bikes require the use of a 216-250 V, 50 Hz and a 15 A “Dedicated Circuit”, with a non-looped (isolated) neutral/ground for power. This outlet should be a NEMA 6-15R and have the same configuration as the plug. No adapter should be used with this product. These bikes can be daisy-chained together with up to 4 units per 15 A dedicated circuit. Matrix daisy-chain cord adapters are sold separately.
DEDICATED CIRCUIT AND ELECTRICAL INFO
A “Dedicated Circuit” means that each outlet you plug into should not have anything else running on that same circuit. The easiest way to verify this is to locate the main circuit breaker box, and turn off the breaker(s) one at a time. Once a breaker has been turned off, the only thing that should not have power to it are the units in question. No lamps, vending machines, fans, sound systems, or any other item should lose power when you perform this test. Non-looped (isolated) neutral/grounding means that each circuit must have an individual neutral/ground connection coming from it, and terminating at an approved earth ground. You cannot “jumper” a single neutral/ground from one circuit to the next.
ELECTRICAL REQUIREMENTS
For your safety and to ensure good unit performance, the ground on this circuit must be non-looped (isolated). Please refer to NEC article 210-21 and 210-23. Any alterations to the standard power cord provided could void all warranties of this product.
The 3x, 5x and 7xe bikes are designed to be self-powered and do not require an external power supply source to operate. Without an external power supply, the console’s start-up time may be delayed. Add-on TV’s and other console accessories will increase the time needed for start-up. An external power supply will ensure power is provided to the console at all times and is recommended when add-on accessories are used.
For units with an integrated TV (like the 7xe and 7xi), the TV power requirements are included in the unit. An RG6 coaxial cable with ‘F Type’ compression fittings on each end will need to be connected to the cardio unit and the video source. Additional power requirements are not needed for the add-on digital TV (3x and 5x). For units with an add-on PCTV (3x and 5x), the TV power requirements are separate.
North American power cord plugs shown.
Depending on your country, the plug type may vary.
GROUNDING INSTRUCTIONS The unit must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. The unit is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. If the user does not follow these grounding instructions, the user could void the Matrix limited warranty.
ADDITIONAL ELECTRICAL INFO In addition to the dedicated circuit requirement, the proper gauge wire must be used from the circuit breaker box, to each outlet that will have the maximum number of units running off of it. If the distance from the circuit breaker box to each outlet, is 100 ft (30.5 m) or less, then 12 gauge wire should be used. For distances greater than 100 ft (30.5 m) from the circuit breaker box to the outlet, a 10 gauge wire should be used.
ENERGY SAVING / LOW-POWER MODE All units are configured with the ability to enter into an energy saving / low-power mode when the unit has not been in use for a specified period of time. Additional time may be required to fully reactivate this unit once it has entered the low-power mode. This energy saving feature may be enabled or disabled from within the ‘Manager Mode’ or ‘Engineering Mode.
ADD-ON PCTV (3X AND 5X) A 15 A or 20 A “Dedicated Circuit” with a non-looped (isolated) neutral/ground is required. Each PCTV requires at least 1.2 A of current. No more than 12 PCTVs should be used for each 15 A circuit and no more than 16 PCTVs should be used for each 20 A circuit. The power outlet should have the same configuration as the plug. No adapter should be used with this product. An RG6 coaxial cable with ‘F Type’ compression fittings will need to be connected between the video source and each add-on PCTV unit. See the PCTV Manual for web connection requirements.
ADD-ON DIGITAL TV (3X AND 5X) Additional power requirements are not needed for the add-on digital TV. An RG6 coaxial cable with ‘F Type’ compression fittings will need to be connected between the video source and each add-on digital TV unit.
BATTERY CHARGING (3X AND 5X) The bike saves its batter charge by moving into a shutdown mode whenever PEDAL FASTER appears on the display. If the user does not maintain a pedal rate of 40 RPM or higher, a 30 second shutdown process begins. When the battery voltage is low, LOW BATTERY appears on the display. This means it is time to recharge the battery. If the battery must be charged, use the optional power adapter charging unit. The charger should be connected to the bike for a minimum of eight hours to ensure a thorough charge.
4
CHAPTER 3: PREVENTATIVE MAINTENANCE
3.1 RECOMMENDED CLEANING TIPS
In order to maximize life span, and minimize down time, all Matrix Fitness Equipment requires regularly
scheduled cleaning.
YOU WILL NEED:
- Mild dish soap and water mixture in a spray bottle (10:1 water to soap ratio).
- Lint free 100% cotton cleaning cloths or Microfiber cleaning cloths.
- Vacuum / Shop Vac with extendable hose and soft brush attachment.
- Corrosion Block (available from Matrix - part # ZMS4001374).
DAILY:
1. Wipe down the unit after each use with a mild dish soap and water mixture. NOTE: Spray the soap / water mixture onto the cloth. NEVER spray directly onto the equipment. We recommend that you do NOT allow customers to use spray bottles to clean the equipment. If the cleaner is sprayed directly on the equipment or overspray is present, it may cause your equipment to rust and / or cause damage to con sole overlays.
WEEKLY:
1. With a clean dry 100% lint free cloth and water / soap mixture, wipe down the entire frame so it is free of dust, dirt, and sweat.
2. With a clean dry 100% lint free cloth and water / soap mixture, wipe down the entire console area including the hand grips and hand rails.
MONTHLY:
1. Vacuum under and around the Bike. If you need to move it, unplug the unit first.
2. Remove the shrouds and use a vacuum to remove any dust or dirt built up under the covers. NOTE: Be careful not to damage or unplug any of the wiring.
3. Apply Corrosion Block to the metal part of the iPod cable.
-
3.2 CHECK FOR DAMAGED PARTS
DO NOT use any equipment that is damaged or has worn or broken parts. Use only replacement parts supplied by Matrix Fitness Systems.
MAINTAIN LABELS AND NAMEPLATES. Do not remove labels for any reason. They contain important information. If unreadable or missing,
contact Matrix Fitness Systems for a replacement. 1-866-693-4863, www.matrixfitness.com
MAINTAIN ALL EQUIPMENT Preventative maintenance is the key to smooth operating equipment. Equipment needs to be inspected at regular intervals. Defective components must be replaced immediately. Improperly working equipment must be kept out of use until it is repaired. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is qualified to do so. Matrix Fitness Systems will provide service and maintenance training at our corporate facility upon request or in the field if proper arrangements are made.
5
CHAPTER 3: PREVENTATIVE MAINTENANCE
3.3 CARE AND MAINTENANCE INSTRUCTIONS
In order to maximize life span, and minimize down time, all MATRIX equipment requires regular cleaning, and maintenance items performed on a scheduled basis. This section contains detailed instructions on how to perform these items and the frequency of which they should be done. Some basic tools and supplies will be necessary to perform these tasks which include (but may not be limited to):
* Metric Allen wrenches * #2 Phillips head screwdriver * Adjustable wrench * Commercial Pedal wrench (available from Matrix - part # ZMS4001254)
You may periodically see addendums to this document, as the Matrix Technical Support Team identifies items that require specific attention, the latest version will always be available on the Matrix web site at www.matrixfitness.com.
DAILY MAINTENANCE ITEMS
1) Look and listen for loose fasteners, unusual noises, and any other indications that the equipment may be in need of service.
2) Attempt to wobble the unit from side to side and front to back. Level if needed (see Section 10.4).
WEEKLY MAINTENANCE ITEMS
1) Check the pedal straps for damage.
2) Clean the grooves on the foot pedals.
MONTHLY MAINTENANCE ITEMS
1) Frequently vacuum the floor beneath the unit to prevent the accumulation of dust and dirt which can affect the smooth operation of the unit.
2) Check that the pedal and crank assembly are tight with no free play or wobble in them. Make sure to use a commercial grade pedal wrench to get the pedals as tight as possible.
3) Check the condition of the seat upholstery. Make sure that the seat adjustment mechanism is operating correctly.
YEARLY MAINTENANCE ITEMS
1) Remove the front shrouds and check the belt for damage, alignment, and proper tension.
6
CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION
4.1 CONSOLE DESCRIPTION
WORKOUT KEYS: Simple program view and selection buttons.
GO: One touch Start.
UP / DOWN LEVEL: Easy information and level selection.
UP / DOWN TIME: Easy information and time adjustment.
STOP: Ends workout and shows workout summary data.
NUMBER KEYPAD: Workout data input for workout setup. Level adjustment during workout.
COOL DOWN: Puts bike into Cool Down mode.
FAN: Allows for fan speed selection (fan has 3 operating speeds).
TOGGLE DISPLAY: Allows user to select what information is displayed on the console.
LANGUAGE: Select language.
7
CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION
4.2 WORKOUT SETUP STEPS - MANUAL
GO - Press to immediately begin a workout. Workout, resistance
level, and time will automatically go to default settings. Pressing GO will not prompt user for age, weight, or level settings.
1) Start pedaling and press the GO key to begin your workout. 2) The display will read 3, 2, 1, Begin and then the program will start.
MANUAL - Manual allows the user to input more information
while defining their own workout. Calorie expenditure will be more accurate when inputting information in Manual than by pressing GO.
1) Start pedaling, press the MANUAL key. Then press ENTER.
2) Select Level by using the UP or DOWN LEVEL keys and press ENTER.
3) Select Time by using the UP or DOWN LEVEL keys and press ENTER.
4) Select Weight by using the UP or DOWN LEVEL keys and press ENTER.
5) Press GO, and then the display will read 3, 2, 1, Begin and then the program will start.
4.3 WORKOUT SETUP STEPS - FAT BURN
FAT BURN - Fat burn is a level based program that is designed
to help users burn fat through various resistance level changes.
1) Start pedaling and press the FAT BURN key. Then press ENTER.
2) Select Level by using the UP or DOWN LEVEL keys and press ENTER.
3) Select Time by using the UP or DOWN LEVEL keys and press ENTER.
4) Select Weight by using the UP or DOWN LEVEL keys and press ENTER.
5) Press GO, then the display will read 3, 2, 1, Begin and then the program will start.
4.4 WORKOUT SETUP STEPS - LEVEL BASED
ROLLING HILLS - The Rolling Hills program is a level based
program that automatically adjusts the resistance level to simulate real terrain.
1) Start pedaling and press the ROLLING HILLS key. Then press ENTER.
2) Select Level by using the UP or DOWN LEVEL keys and press ENTER.
3) Select Time by using the UP or DOWN LEVEL keys and press ENTER.
4) Select Weight by using the UP or DOWN LEVEL keys and press ENTER.
5) Press Go, then the display will read 3, 2, 1, Begin and then the program will start.
INTERVAL TRAINING - The Interval Training program is a
level based program that automatically adjusts the resistance of the machine from low to high intensity settings at regular intervals.
1) Start pedaling and press the INTERVAL TRAINING key. Then press ENTER.
2) Select Level by using the UP or DOWN LEVEL keys and press ENTER.
3) Select Time by using the UP or DOWN LEVEL keys and press ENTER.
4) Select Weight by using the UP or DOWN LEVEL keys and press ENTER.
5) Press GO then the display will read 3, 2, 1, Begin and then the program will start.
RANDOM - Random is a level based workout that randomly
adjusts the resistance of the machine.
1) Start pedaling and press the key next to RANDOM key. Then press ENTER.
2) Select Level by using the UP or DOWN LEVEL keys and press ENTER.
3) Select Time by using the UP or DOWN LEVEL keys and press ENTER.
4) Select Weight by using the UP or DOWN LEVEL keys and press ENTER.
5) Press GO, then the display will read 3, 2, 1, Begin and then the program will start.
8
CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION
4.5 WORKOUT SETUP STEPS - FITNESS TEST
FITNESS TEST -The Cooper Fitness Test measures cardiovascular fitness and proves an estimated sub-maximal VO2 result. It is based
on power output according to ACSM standards and was developed by the Cooper Institute© (www.cooperinstitute.org). User RPMs must remain between 60-80 RPM during the test. The test will end when the user can no longer maintain this speed. Use of a heart rate strap is optional but provides more data.
The test starts at a low intensity level and gradually increases in intensity (difficulty) every 2 minutes. As it increases, the user must maintain 60-80 RPM to advance to the next level. The test could take upwards of 30+ minutes for very fit individuals. Once the test ends a recovery period (cool down) will begin and the user's results are calculated and displayed. Results are based on the number of stages completed. Incline will not be adjustable during the test.
1) Start pedaling and press the FITNESS TEST key. Then press ENTER.
2) Select Age by using the UP or DOWN LEVEL keys and press ENTER.
3) Select Gender by using the UP or DOWN LEVEL keys and press ENTER.
4) Select Weight by using the UP or DOWN LEVEL keys and press ENTER.
5) Press GO, then the display will read 3, 2, 1, Begin and then the program will start.
6) Once the workout is complete, the display will read the results of the Fitness Test.
STAGES COMPLETED:
1 Well Below Average 2 Well Below Average 3 Below Average 4 Below Average 5 Average 6 Average 7 Above Average 8 Above Average 9+ Well Above Average
9
CHAPTER 4: CONSOLE OVERLAY AND WORKOUT DESCRIPTION
4.6 WORKOUT SETUP STEPS - TARGET HEART RATE
TARGET HEART RATE - The Matrix U5x-04 Bike comes with
standard digital contact heart rate sensors and are POLAR telemetry compatible. The heart rate control workout mode allows the user to program their desired heart rate zone, and the bike will automatically adjust the level based upon the user's heart rate. The heart rate zone is calculated using the following equation: (220-Age)8%=target heart rate zone. The user must wear a POLAR telemetric strap or continually hold onto the contact heart rate grips for this workout.
Locate the metal sensors on the handlebars of the bike. Notice that there are two separate pieces of metal on each grip. You must be making contact with both pieces of each grip to get an accurate heart rate reading. You can grab these sensors in any program to view your current heart rate.
1) Start pedaling and press the HEART RATE key. Then press ENTER.
2) Select Age by using the UP or DOWN LEVEL keys and press SELECT.
3) Select Target HR Percentage by using the UP or DOWN LEVEL keys and press SELECT.
4) Select Time by using the UP or DOWN LEVEL keys and press SELECT.
5) Select Weight by using the UP or DOWN LEVEL keys and press SELECT.
6) Press GO, then the display will read 3, 2, 1, Begin and the program will start.
4.7 WORKOUT SETUP STEPS - CONSTANT WATTS
CONSTANT WATTS - Constant Watts is a unique program
that allows you to vary your cadence or RPM and the bike's resistance level will adjust accordingly to your selected goal. The quicker you pedal, the less resistance for the goal selected.
1) Start pedaling and press the CONSTANT WATTS key. Then press ENTER.
2) Select Watts by using the UP or DOWN LEVEL keys and press SELECT.
3) Select Time by using the UP or DOWN LEVEL keys and press SELECT.
4) Select Weight by using the UP or DOWN LEVEL keys and press SELECT.
5) Press GO, then the display will read 3, 2, 1, Begin and the program will start.
10
CHAPTER 5: MANAGER MODE
5.1 USING MANAGER MODE
The Manager's Custom Mode allows the club owner to customize the bike for the club.
1) To enter Manager Mode, press and hold down the UP and DOWN LEVEL keys. Continue to hold down these two keys until the display reads Manager Mode and hit ENTER (Figure A).
2) To scroll through the list of options in Manager Mode, use the UP and DOWN LEVEL keys. Each of the custom settings will show on the display.
3) To select a custom setting, press the ENTER key when the desired setting is shown.
4) To change the value of the setting, use the UP and DOWN LEVEL keys.
5) To confirm and save the value of the setting, press the ENTER key.
6) To exit the setting without saving, press the BACK key.
7) Press and hold the STOP key for 3-5 seconds to return to normal operation.
5.2 MANAGER MODE OVERVIEW
CUSTOM SETTING DEFAULT MINIMUM MAXIMUM DESCRIPTION
Maximum Time 60 min 5 min 99 min Sets the total run time of any program.
Default Time 30 min 5 min Maximum
Default Level 1 1 30 Starting resistance when GO is pressed or when no resistance is
Default Age 30 10 100 Starting age when GO is pressed or when no age is selected during
Default Weight 150 lbs /
75 kg
Accumulated Distance N/A 0 999,999
Accumulated Time N/A 0 999,999
Software N/A N/A N/A Current software version of UCB / LCB.
Timer Mode Up Up Down Determines whether the timer counts up or down.
Speed / Distance Mode Mile Mile Kilometer Displays distance in miles or kilometers.
Out of Order Off On Off Locks the machine when out of order.
Gender Male Male Female Determines the gender of the user when not selected during program
Language English English English Sets the language for the console. Select between English, Spanish,
Sound Mode On On Off Turns the chime on / off when a button is pressed.
80 lbs / 36 kg400 lbs /
Time Setting
182 kg
Miles
hours
Workout time when GO is pressed or when no time is selected during program set up.
selected during program set up.
program set up.
Weight used for program calorie expenditure calculations.
Total distance for all programs.
Total time for all programs displayed in hours.
set up.
German, French, Italian, and Dutch.
11
CHAPTER 6: ENGINEERING MODE
6.1 USING ENGINEERING MODE
To enter Engineering Mode, hold the LEVEL UP and DOWN keys for 3-5 seconds until Manager Mode appears on the middle LED display. Press the LEVEL UP or DOWN key to scroll to Engineering Mode. Press ENTER to go into Engineering Mode.
CODE DEFAULT OPTIONS DESCRIPTION
Disable Errors No Yes or No No - Shows A-C class error codes. Yes - Shows only C class error codes.
Speed Units Mile Mile or Kilometer Set for Mile or Kilometer.
Machine Type U5x-05 H5x-05, U5x-05,
Power Save Time 30 Seconds 30-60 Seconds Power saving time for the self powered frame.
Pause Time 30 Seconds 15 - 120 Seconds For non self powered frames only. Not used on this model.
Serial Number N/A N/A Serial Number input is available for both the Console and Frame. Use the number
Club ID N/A N/A This sets the club ID for clubs using Asset Management.
ErP Mode (Sleep Time)
Audio Source Off Off / TV / PC TV /
AM System WIFI WIFI / RF Radio To select AM output device by WIFI or RF Radio.
Volume Control TV/ PCTV:
Off Off or On (1-30
Output:13
REMOTE TV Output:13
REMOTE TV Input:15
R5x-05, H5x-04, U5x-04, R5x-04, E5x-02, E5x-03
Minutes)
Remote TV
1~ 32 Controls the default TV volume for entertainment wired through the C-Safe port.
1~ 32
1~ 15
The Hybrid bike console should be set to U5x-05.
keys and UP / DOWN LEVEL keys to enter Engineering Mode. Due to the limited LED characters, 2 layers are used to enter the serial number. First Layer:
- PPPPP V
- PPPPP is the product name.
- V is the version. If the version is A, just leave this blank. Second Layer
- YY MM nnnnn.
- YY is the year (11, 12).
- MM is the month (e.g. 08, 09, 10).
- nnnnn is the actual serial number. Use the UP / DOWN LEVEL keys to navigate the layers and the number keys to input the serial number. The product name is dependent on the Machine Type setting. For example, the console is EP612 with version A and the manufactured date is
2012.08 with 98765. The frame is CB93 and the manufactured date is 2013.06 with 12345. Their serial numbers are: Console SN: EP612 1st layer, 120898765 2nd layer. Frame SN: CB93 1st layer, 130612345 2nd layer.
If there is no use of the machine over a period of time, the console LEDs will turn off (go into ErP mode).
Manual setting that sets which outside TV will have audio through the console audio ports.
a. Input Default (DF : 15 / Range : 1 ~ 15) b. Max Default (DF : 32 / Range : 1 ~ 32) c. Output Default (DF : 13 / Range : 1 ~ Max) Remote TV support a / b / c item. TV and PCTV only support c item.
12
CHAPTER 7: SERVICE MODE
7.1 USING SERVICE MODE
To enter Service Mode, hold the LEVEL UP and DOWN keys for 3-5 seconds until Manager Mode appears on the middle LED display. Press the LEVEL UP or DOWN key to scroll to Service Mode. Press ENTER to go into Service Mode.
CODE DEFAULT OPTIONS DESCRIPTION
Service 1 Display Test Press the ENTER key repeatedly
Service 2 Keypad Test Press any key and the display
Service 3 Distance / Time Distance:
Mile 0 - 99999 Kilometer 0 - 160898 Time: 0 - 999999
Service 4 CSafe / RF Test Press the ENTER key to test
Service 5 Error Log Shows the last 10 errors. Press
Service 6 Set Date / Time Press the LEVEL keys to move
Service 7 Export and Import Parameter Export Parameter - Export all
Service 8 WiFi Function Automatically detects the
to check each set of LEDs on the display sequentially.
should show the corresponding message.
Manually sets the Accumulated Distance and Time.
CSAFE. Press the ENTER key again to test the RF.
and LEVEL UP and DOWN for 3 seconds to clear the errors.
cursor, the number keys to set date / time, and the ENTER key to save.
parameters to a USB device. Import Parameter 1 - Imports the engineer parameters to a USB device except serial number, accumulated distance and time. Import Parameter 2 - Imports the engineer parameters to a USB device.
available IP address and displays it.
13
8.1 ELECTRICAL DIAGRAMS
CHAPTER 8: TROUBLESHOOTING
14
CHAPTER 8: TROUBLESHOOTING
8.1 ELECTRICAL DIAGRAMS - CONTINUED
15
8.1 ELECTRICAL DIAGRAMS - CONTINUED
MCB POWER WIRE
CHAPTER 8: TROUBLESHOOTING
DIGITAL COMMUNICATION WIRE
16
CHAPTER 8: TROUBLESHOOTING
8.1 ELECTRICAL DIAGRAMS - CONTINUED
PULSE SENSOR WIRE - RIGHT
PULSE SENSOR WIRE - LEFT
17
CHAPTER 8: TROUBLESHOOTING
8.1 ELECTRICAL DIAGRAMS - CONTINUED
PULSE EXTENDED WIRE
18
8.2 LCB LED INDICATORS
============================ Status LED =============================
LED1: Console Power Supply. (Light: LCB give the power for console)
LED4: Boost Controller
LED5: Battery Charge Control.(Light : Battery just charge)
LED6: Battery Connection Reverse Protection. Light: reverse
LED7: MCU-B LCB Working Status. (Flash: Working)
LED8: Resistance Offset. Light: Normal
LED9: MCU A <-> B Communication. (Flash: Working)
LED10: UCB <-> LCB Communication. (Flash: Working)
LED11: 5V (For LCB MCU power)
LED12: 12V (For LCB power)
LED13: RPM
LED14: MCU-A LCB Working Status (Flash: Working)
LED15: MCU-A Error (Light: LCB get error)
LED16: MCU A <-> B Communication (Flash: Working)
LED18: Electromagnet PWM
CHAPTER 8: TROUBLESHOOTING
19
Loading...
+ 51 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use