Matrix MX-U5, MX-R5 Owner's Manual
OWNER’S MANUAL
CYCLES
Table of Contents
1.0) IMPORTANT SAFETY INSTRUCTIONS
Read and Save These Instructions 1
Setting Up the Cycle 1
1.1) Installation Requirements 1
1.2) Preventative Maintenance and Cleaning Tips 1
2.0) USING MANAGER PREFERENCE MODE 2
2.1) Using C Safe 2
2.2) Setting Up Fit Connexion™ 2
3.0) ADJUSTING THE SEAT HEIGHT 3
3.1) Upright Seat Height 3
3.2) Recumbent Seat Height 3
3.3) Recumbent Lumbar Support 3
4.0) USING THE CYCLE OR RECUMBENT
4.1) Console Description 4
4.2) Manual Operation 4
4.3) Operating Level Based Programs 4
4.4) Heart Rate Control 5
4.5) Constant Watts 5
5.0) EQUIPMENT SPECIFICATIONS
5.1) MX-R5 6
5.2) MX-U5 7
6.0) PARTS AND ASSEMBLY 9
6.1) MX-R5 Exploded View 11
6.2) Parts List 12
6.3) Assembly Instructions 14
6.4) MX-U5 Exploded View 23
6.5) Parts List 24
6.6) Assembly Instructions 26
1) Important Safety Instructions
READ AND SAVE THESE INSTRUCTIONS
• This Cycle is intended to for commercial use
• To insure your safety and protect the equipment, read all instructions before operating the
MATRIX Cycle.
When using an electrical product, basic precautions should always be followed, including
the following:
DANGER To reduce the risk of electric shock:
• Always unplug this equipment from the electrical outlet immediately after using and
before cleaning.
Your MATRIX Cycle is self-generating (requiring no external power source) and must be pedaled to power up the console.
WARNING To reduce the risk of burns, fire, electrical shock or injury to persons that may be
associated with using this product:
• An appliance should never be left unattended when plugged in. Unplug from outlet when
not in use and before putting on or taking off parts.
• This product must be used for its intended purpose described in this Owner’s Guide. Do not
use other attachments that are not recommended by the manufacturer. Attachments may
cause injury.
• To prevent electrical shock, never drop or insert any object into any opening.
• Do not remove the side covers. Service should only be done by an authorized service technician.
• Never operate the Cycle with the air openings blocked, Keep the air openings clean, free of
lint, hair and the like.
• Never operate product if it has a damaged cord or plug, if it is not working properly, if it has
been damaged, or immersed in water. Return the appliance to a service center for examination
and repair.
• Do not carry this appliance by supply cord or use cord as handle.
• Keep any power cord away from heated surfaces.
• Keep hands and loose clothing away from moving parts.
• Close supervision is necessary when Cycle is used by or near children, invalids, or disabled persons.
• Do not use outdoors.
• Do not operate where aerosol (spray) products are being used or where oxygen is being
administer
ed.
• To disconnect, turn all controls to the off position, then remove plug from outlet
• Connect this Cycle to a properly grounded outlet only.
CAUTION If you experience chest pain, nausea, dizziness or shortness of breath, STOP exercis-
ing immediately and consult a physician befor
e continuing.
SETTING UP THE CYCLE
Assembly instructions have been provided with your Cycle. For your safety, please read and follow each of the steps in the assembly guide. To obtain a copy of the assembly guide, please
contact MATRIX FITNESS SYSTEMS.
1.1 INSTALLATION REQUIREMENTS
Your MATRIX Cycle is designed to be self contained and does not require a power
supply to operate.
Fit ConnexionTMrequires a 9 volt battery and a 110 volt power supply to operate the monitor.
Use only the power supply provided by the manufacturer, please contact MATRIX FITNESS for
a replacement.
CAUTION Use of the wrong power supply may cause damage to your Cycle and/or entertain-
ment device.
Locate a level stable surface to position Cycle. The Cycle has four leveling feet located under
the foot support. If your Cycle wobbles in the location where you intend to use it, loosen the
lock nut on the adjusting foot and adjust the feet until stable. Once level, lock the adjusting
feet by tightening the lock nut to the frame.
1.2 PREVENTATIVE MAINTENANCE AND CLEANING TIPS
Preventative maintenance and daily cleaning will prolong the life and look of your Matrix fitness equipment.
Please read and follow these tips.
• Position the equipment away from direct sunlight. The intense UV light can cause discoloration
of plastics.
• Locate your equipment in an area with cool temperatures and low humidity.
• Clean with a soft 100% cotton cloth.
• Clean with non-ammonia based cleaners.
• Wipe seats, handles, hear
t rate grips, and handlebars clean after each use.
• Do not pour liquids dir
ectly onto your equipment. This can cause damage to the equipment
and in some cases electr
ocution.
• Check pedal safety straps weekly for wear.
• Adjust leveling feet when equipment wobbles or r
ocks.
• Maintain a clean area around equipment free from dust and dirt.
1
2) Using Manager Preference Mode
2.0 USING MANAGER PREFERENCE MODE
Your MATRIX Cycle is designed to allow you to customize settings for your preferences and
diagnostics. The Manager Preference Mode can only be accessed while the Cycle is powered
up. Follow the instructions to adjust the Cycle computer for your desired settings.
STEP 1 Power up the Cycle and Hold the UP and DOWN arrow keys for 3 seconds. The word
Manager will appear in the alphanumeric window and will enter into the Manager
Preference Setting automatically after 3 seconds. Continue to pedal until finished.
STEP 2 Select information you would like to view or change from the following list, by using
the UP or DOWN arrows. Press ENTER to select.
Manager preference mode will allow you to view and set the following.
DISPLAY CODE: INFORMATION USER DEFINABLE DEFAULT VALUE MIN. MAX.
Manager P0: Maximum program time Y 95 min 5 95
P1: Default time Y 20 min 5 95
P2: Default level Y L1 L1 L20
P3: Default weight Y 150 lbs 80 lbs 400 lbs
P4: Speed Y Miles Miles KM
P5: Machine Y BI BI RE, EL
P6: TV IR Y On On Off
P7: Cardio Entertainment Y On On Off
P8: Accumulated Distance
P9: Accumulated Time
P10: Software Version
STEP 3 Use UP or DOWN arrows to increase or decrease values.
STEP 4 Press START to save and enter selected values and exit to STEP 2.
STEP 5 Exit by pressing Start. Screen will reset to Start up.
2.1 USING CSAFE s
Matrix is the leader in entertainment availability. On the back of the console are three RJ45
receptacles. They are marked CSAFE IN, CSAFE OUT, and ENTERTAINMENT.
Use the CSAFE IN to plug in any CSAFE device using the RJ45 connector CSAFE OUT allows
CSAFE
pr
oducts to be daisy chained together fr
om one unit to the next. The connection is as follows;
2.2 SETTING UP FIT CONNEXION™
Fit Connexion
TM
Your equipment is preset to offer you the maximum benefit of your desired entertainment offering.
Whether it is FIT CONNEXIONTMor other CSAFE entertainment packages, Matrix makes it easy
to connect. Look on the back of the console and locate the receptacle labeled ENTERTAINMENT.
This port is specific for audio and visual entertainment devices. CSAFE ready products can plug
in and utilize the volume, channel and headphone connector
When installing Fit Connection make sure you are using the power cord supplied with your
package. Other power cords could cause malfunctions with your product.
Assemble the Fit Connection bracket by following the instructions supplied in your package.
Make sure you feed the power cord and coaxial cable through the round hole at the top of the
bracket. Insert the monitor and fasten with the screw provided.
Connect the coaxial cable and the power cord to the monitor.
Take the Fit Connexion
TM
audio cord and plug it into the audio out on the back side of the monitor. The RJ45 needs to now be plugged into the Jack labeled Entertainment. This cord provides
the audio to your headphones.
At the front base of the unit you will see the Fit Connexion TM coaxial cable and power supply connectors. Connect the coaxial cable and the power supply. Turn the monitor on and see if it has power.
Follow the instructions provided with your monitor to select language and input device options.
3.0
2
CSAFE IN
CSAFE OUT
CSAFE IN
CSAFE OUT
CSAFE IN
CPU
U
NIT 1
UNIT 2
UNIT 3
3) Adjusting the Seat Height
3.0 ADJUSTING THE SEA
T HEIGHT
Your MATRIX Cycle is designed for ease of use. We have incorporated seat height adjustments
that are easily located and simple to adjust.
3.1 UPRIGHT SEAT HEIGHT
To adjust the seat height on the Upright Cycle, locate the red pull pin before you mount the
Cycle. To lower the seat down, pull the red knob while holding the seat with the other hand
and slide up or down accordingly. To adjust seat height up, simply raise the seat to desired
position. Our automatic seat lock will set. Make sure you are not seated when you pull the
knob or pull seat up.
3.2 RECUMBENT SEAT HEIGHT
To adjust you’re seat height on the Recumbent Cycle locate the red lever under the right side
of the seat before you mount the Cycle. Place your right hand on the red adjustment handle
under the right side of the seat. Place feet on the ground while seated and slide forward if
needed. Place feet on pedals, gently lift lever under the right side of the seat. Using legs slowly push and slide the seat up or down to desired position. Release lever and allow to lock into
place.
3.3 RECUMBENT LUMBAR SUPPORT
The red knob on the side of the seat is for adjusting the lumbar support. To adjust, simply turn
the knob located on the back rest. Turn the knob forward to increase support and backward to
decrease support until desired comfort has been achieved.
3
4) Using the Cycle or Recumbent
4.1 CONSOLE DESCRIPTION
PROGRAMS Simple program view and selection buttons. Matrix Cycles feature seven programs.
START / QUICK START One touch Quick Start and Start any time during preference selection.
UP / DOWN Easy information and level selection.
ENTER / SELECT SCREEN / RESET This multi-function button enters information when setting up
programming options, toggles information displayed and if held down for 5 seconds resets
the Cycle to Start-up mode.
DISPLAY VIEW These three buttons allow the user to customize the way the unit’s lights are dis-
played.
ENTERTAINMENT Control the CHANNEL and VOLUME of your attached TV or entertainment
system. (Must have Fit Connexion
TM
or entertainment source connected)
HEAD PHONE JACK Located at the base of the console, just plug in a headset and use the
ENTERTAINMENT buttons to adjust VOLUME. (Must have Fit ConnexionTMor entertainment
source connected)
4.2 MANUAL OPERA
TION
MATRIX design makes using the programs as easy as one touch of a button.
QUICK START Start pedaling and press QUICK START to begin workout.
MANUAL MODE allows you enter desired time, level, and weight.
STEP 1 Select Manual program button on left of panel.
Press Enter or wait 5 seconds.
NOTE Selecting START will start program.
STEP 2 Select Time by using the UP or DOWN arrow keys. When finished
Press Enter or wait 5 seconds.
NOTE Selecting START will start program.
STEP 3 Select Level by using UP or DOWN arrow keys. You can change the level at any time
during workout. When finished,
Press Enter or Wait 5 seconds.
NOTE Selecting START will start program.
STEP 4 Select Weight by using the UP or DOWN arrow keys.
Press START or ENTER to begin workout.
Display
TIME
Starting 3
Starting 2
Starting 1
4.3 OPERATING LEVEL BASED PROGRAMS
Your MATRIX Cycle offers versatile programs to keep the user motivated.
The following Instructions will guide you through simple steps to select INTERVALS, ROLLING,
FAT BURN, and RANDOM programs.
STEP 1 Select the program button on left of panel.
Press ENTER or wait 5 seconds.
NOTE Selecting START will begin program.
STEP 2 Select Time by using the UP or DOWN arrow keys. When finished
Press ENTER or wait 5 seconds.
NOTE Selecting START will begin workout.
STEP 3 Select Level by using UP or DOWN arrow keys. You can change the level at any time
during workout. When finished,
Press ENTER or Wait 5 seconds.
NOTE Selecting ST
ART will begin workout.
STEP 4 Select Weight by using the UP or DOWN arrow keys.
Press START or ENTER to begin workout.
Display
4
4) Using the Cycle or Recumbent
TIME
Starting 3
Starting 2
Starting 1
4.4 HEART RATE CONTROL
For your convenience, MATRIX FITNESS CYCLES come standard with digital contact heart rate
sensors and POLAR telemetry compatible.
Locate the metal sensors on the handrail of the Cycle. Notice there are two separate pieces of
metal on each grip. You must be making contact on both pieces of each grip to get an accurate heart rate reading. You can grab these sensors in any program to view your current heart
rate located in the lower left hand window marked Heart Rate.
Heart Rate Program
Follow these easy Steps to enter into the Heart Rate Program.
STEP 1 Select TARGET HR program button on left of panel.
Press Enter or wait 5 seconds.
NOTE Selecting START will start program.
STEP 2 Select Time by using the UP or DOWN arrow keys. When finished
Press Enter or wait 5 seconds.
NOTE Selecting START will start program.
STEP 3 Using the following chart, select Target Heart Rate by using UP or DOWN arrow keys.
You can change the Target Heart Rate at any time during workout. When finished,
Press Enter or Wait 5 seconds.
NOTE Selecting START will start program.
STEP 4 Select Weight by using the UP or DOWN arrow keys.
Press START or ENTER to begin workout.
Display
TIME
Starting 3
Starting 2
Starting 1
4.5 CONSTANT WATTS
Constant Watts program is a unique program that allows you to vary your cadence or RPM and
the Cycles resistance will adjust accordingly to your selected goal. The quicker you pedal the
less resistance for the goal selected.
Follow these easy Steps to enter into the Constant Watts Program.
STEP 1 Select CONSTANT WATTS program button on left of panel.
Press Enter or wait 5 seconds.
NOTE Selecting START will start program.
STEP 2 Select Time by using the UP or DOWN arrow keys. When finished
Press Enter or wait 5 seconds.
NOTE Selecting START will start program.
STEP 3 Select Constant Watts goal by using UP or DOWN arrow keys. You can change the
watts target at any time during workout. When finished,
Press Enter or Wait 5 seconds.
NOTE Selecting START will start program.
STEP 4 Select Weight by using the UP or DOWN arrow keys.
Press START or ENTER to begin workout.
Display
TIME
Starting 3
Starting 2
Star
ting 1
5
POLAR TARGET HEART RAT E ZONE
HEAVY MODERATE LIGHT
220
20
AGE
HR BEATS
PER MINUTE
25 30 35 40 45 50 55 60 65
200
180
160
140
120
100
80
SPECIFICA
TIONS
Product Name R5
Foot Print 49"H x 62"L x 25"W
Weight 132 lbs
Max User Weight 400 lbs = 181 kg
Frame Construction Aluminum/Steel
Self Contained Yes
Resistance Type Generator
Resistance Levels 20
PROGRAMS
One Button Quick Start Yes
Random (20 profiles) Yes
Target Heart Rate Yes
Interval Yes
Constant Watts Yes
Rolling Yes
Fat Burn Yes
HEART RATE
Polar Telemetry Yes
Contact Heart Rate Yes
ENTERTAINMENT READY
Volume Control Yes
Channel Control Yes
Display View Control 3 Views
Coaxial Cable Connection Yes
Acc TV Power Connection Ye s
Monitor Mount Yes
IR Port Yes
Head Phone Jack yes
5) Equipment Specifications
>recumbent cycle
MX-R5
MACHINE
WEIGHT SIZE
132 lbs
inches = 49” x 62” x 25”
60 kg
cm = 128.5 x 157.5 x 63.5
6
5) Equipment Specifications
> upright cycle
MX-U5
MACHINE
WEIGHT SIZE
106 lbs
inches = 57” x 44” x 63.5”
48 kg
cm = 144.8 x 111.8 x 25
7
SPECIFICA
TIONS
Product Name U5
Foot Print 57"H x 44"L x 25"W
Weight 106 lbs
Max User Weight 400 lbs = 181 kg
Frame Construction Aluminum/Steel
Self Contained Yes
Resistance Type Generator
Resistance Levels 20
PROGRAMS
One Button Quick Start Yes
Random (20 profiles) Yes
Target Heart Rate Yes
Interval Yes
Constant Watts Yes
Rolling Yes
Fat Burn Yes
HEART RATE
Polar Telemetry Yes
Contact Heart Rate Yes
ENTERTAINMENT READY
Volume Control Yes
Channel Control Yes
Display View Control 3 Views
Coaxial Cable Connection Yes
Acc TV Power Connection Yes
Monitor Mount Yes
IR Port Yes
Head Phone Jack Yes
THIS PAGE INTENTIONALLY BLANK
Loading...