Matrix MPW05 User Manual
MATRIX POWERWATCH X PAIR WITH YOUR SMARTPHONE OPTIMAL CHARGING CONDITIONSREAL TIME ENERGY HARVESTINGTURN ON
POWER & BACKLIGHT
TRACK ACTIVITY
and PowerWatch X.
MODE button
SCROLL knob
SET button
1. Hold MODE and SET for one second.
21 1
1. Download & launch iOS or Android app.
2. From Welcome screen, press SET.
Download the Matrix PowerWatch X app for iOS or Android.Note: The following instructions apply to PowerWatch, Black Ops
The bars around the display rise and fall depending on
how much heat you provide. Put your PowerWatch X on
a friend’s wrist, observe as the bars rise, then thank them
for donating their calories to charge your battery!
In order charge its internal battery, the MATRIX PowerWatch X
requires a temperature dierential with the ambient air.
This means that it can generate more power when the air
is cooler, and also when you are active and your skin is
warmer. Here is a chart that shows how fast the PowerWatch X
will charge its internal battery at dierent air temperatures:
How Fast the PowerWatch X Charges
Air Temperature
Sitting
Walking
Running
60º
Quickly
Very quickly
Very quickly
70º
Slowly
Quickly
Very quickly
80º
No
Slowly
Quickly
As you can see on the chart, the PowerWatch X will
charge its battery most quickly when you are active
(walking or running), and when the ambient temperature
is below 80°F. Above 90°F, the PowerWatch X cannot
charge its internal battery.
PowerSave Mode:
The PowerWatch X measures your steps and activity.
After about 45 minutes of inactivity, the PowerWatch
X will automatically turn on a screensaver. Moving the
watch or pressing any button will clear the screensaver.
After a week of inactivity, the PowerWatch X will enter
PowerSave mode and turn o the screen. If fully charged,
your settings should be saved for one year or more.
When you are ready to use the PowerWatch X again,
turn it on again by pressing MODE and SET together.
Keeping the PowerWatch X Charged:
1 2
The PowerWatch X charges whenever you wear it.
It charges even faster on the inside of your wrist.
Turn On Backlight:
Hold MODE for two seconds.
1. Press MODE until Daily Activity screen appears.
2. Turn SCROLL to read Steps, Calories and Sleep.
Steps, Calories & Sleep are tracked automatically and reset each day.
Results sync to iOS or Android app.
RUNNING MODE STOP WATCH
1 1 112 2 22
The PowerWatch X can track each run you take.
1. Press MODE until Running Mode screen appears.
2. Press SET to cycle through Start, Stop and Reset.
SYNC DATA TO YOUR SMARTPHONE
1. While under the Watch Settings menu, SCROLL until
the Mobile screen appears.
2. Press SET to sync.
1. Press MODE until Stop Watch screen appears.
2. Press SET to cycle through Start, Stop and Reset
See https://store.powerwatch.com/pages/f-a-q for more details. Display may update slowly, but Stop Watch result is accurate.See https://store.powerwatch.com/pages/f-a-q for more details.
AUTO SLEEP TRACKING NOTIFICATIONS
Incoming call
The PowerWatch X automatically senses when you sleep
and wake.
1. Press MODE until Daily Activity screen appears.
2. Turn SCROLL to read Today’s Sleep data.
Activity goal met
Message received
Alarm ringing
SUPPORT
Our Frequently Asked Questions (FAQ) page is lled
with detailed instructions, tips and warranty information:
https://store.powerwatch.com/pages/f-a-q
The Matrix PowerWatch X does not need charging under
normal use, which includes: adjusting the watch so it
stays in direct contact with the user’s wrist; limiting
Bluetooth and backlight activity while the watch is worn
on the user’s wrist; and not activating the watch
unnecessarily or repeatedly when it is not worn on the
user’s wrist. PowerWatch X rmware can be updated
through the app.
One Year Satisfaction Guarantee
See the FAQ and guarantee at
https://store.powerwatch.com/pages/f-a-q.
For questions or problems, contact us at
support@matrixindustries.com. Thank you!
REGULATORY STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the manufacturer responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Manufacturer’s name: Matrix Industries Inc.
FCC ID: 2ANY2MPW05
EUROPE (EU)
1.Safety:
a) Rated Voltage: 3.8V DC, 105mA
Battery Type: Lithium-ion Polymer (3.8V, 210mAh)
b) Model Name: PowerWatch X
Operation Temperature: 45C max
c)
d) Manufacturer’s name: Matrix Industries Inc
e) Manufacturer name & address: Matrix Industries
Inc. 1455 Adams Drive, Suite 1190 Menlo Park,
CA 94025 USA
f)
CANADA
This device complies with Industry Canada’s licence-exempt
RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device
must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes : (1) l’appareil ne doit
pas produire de brouillage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
2. RF & EMC
• Frequency band(s) = 2402-2480MHz
• Maximum radio frequency power transmitted in
the frequency band(s) = -5.58dBm
• Declaration of Conformity Inserts
• Hereby, Matrix Industries Inc, declares that the
radio equipment type is in compliance with Directive
2014/53/EU. The declaration of conformity may be
consulted at www.powerwatch.com/declaration.pdf
• This equipment may be operated in:
JAPAN
CHINA
Loading...