Matrix G3-MS52, G3-MS51, G3-MS24, G3-MS53, G3-MS20 User Manual
...
AURA
SERIES
G3-MS24
G3-MS51
G3-MS52
G3-MS53
G3-MS20
G3-MS40
G3-MS50
G3-MS80
2
3
IMPORTANT SAFETY INFORMATION
It is the sole responsibility of the purchaser of MATRIX products to instruct all
individuals, whether they are the end user or supervising personnel on proper usage of
the equipment.
It is recommended that all users of MATRIX exercise equipment be informed of the
following information prior to its use.
Do not use any equipment in any way other than designed or intended by the
manufacturer. It is imperative that MATRIX equipment be used properly to avoid injury.
INSTALLATION
1. STABLE AND LEVEL SURFACE: MATRIX exercise equipment must be installed on a
stable base and properly leveled.
2. SECURING EQUIPMENT: Manufacturer recommends that all stationary MATRIX
strength equipment be secured to the oor to stabilize equipment and eliminate
rocking or tipping over. This must be performed by a licensed contractor.
All anchor points must be able to withstand 750 lbs. (3.3 kN) pull-out force.
MAINTENANCE
1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use
only replacement parts supplied by your country’s local MATRIX dealer.
2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They
contain important information. If unreadable or missing, contact your MATRIX
dealer for a replacement.
3. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth
operating equipment as well as keeping your liability to a minimum. Equipment
needs to be inspected at regular intervals.
4. Ensure that any person(s) making adjustments or performing maintenance or
repair of any kind is qualied to do so. MATRIX dealers will provide service and
maintenance training at our corporate facility upon request.
ADDITIONAL NOTES
This equipment should only be used in supervised areas where access and control is
specically regulated by the owner. It is up to the owner to determine who is allowed
access to this training equipment. The owner should consider a user’s: degree of
reliability, age, experience, etc.
This training equipment meets industry standards for stability when used for its
intended purpose in accordance with the instructions provided by the manufacturer.
This training equipment is in compliance with EN 957-1 and the relevant portions of EN
957-2 and EN 957-4.
WARNING
General Selectorized
DEATH OR SERIOUS INJURY CAN OCCUR ON THIS
EQUIPMENT. FOLLOW THESE PRECAUTIONS TO AVOID
INJURY!
1. Keep children under the age of 14 away from this
strength training equipment. Teenagers must be
supervised at all times while using this
equipment.
2. This equipment is not intended for use by persons
with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the equipment by a
person responsible for their safety.
3. All warnings and instructions should be read and
proper instruction obtained prior to use. Use this
equipment for its intended purpose ONLY.
4. Inspect the machine before use. DO NOT use
machine if it appears damaged or inoperable.
5. Do not exceed weight capacity of this equipment.
6. Check to see that the selector pin is completely
inserted into the weight stack.
7. NEVER use the machine with the weight stack
pinned in an elevated position.
8. NEVER use dumbbells or other means to
incrementally increase the weight resistance. Only
use the means provided directly from the
manufacturer.
9. Injuries to health may result from incorrect or
excessive training. Cease exercise if you feel faint
or dizzy. Obtain a medical exam before beginning
an exercise program.
10. Keep body, clothing, hair, and fitness accessories
free and clear of all moving parts.
11. Adjustable stops, where provided, must be used
at all times.
12. When adjusting any adjustable mechanism (stop
position, seat position, pad location, range of
motion limiter, pulley carriage, or any other type),
make certain that the adjustable mechanism is fully
engaged prior to use to prevent unintended motion.
13. Manufacturer recommends that this equipment be
secured to the floor to stabilize and eliminate
rocking or tipping over. Use a licensed contractor.
14. If equipment is NOT secured to floor: NEVER allow
resistance straps, ropes or other means to be
attached to this equipment, as this may result in
serious injury. NEVER use this equipment for
support during stretching, as this may result in
serious injury.
15. DO NOT REMOVE THIS LABEL. REPLACE IF
DAMAGED OR ILLEGIBLE.
NOT a stand-alone unit.
MUST be connected to
other units in a
Matrix-approved
configuration for
added stability.
WARNING
4
PRODUCT SPECIFICATIONS
G3-MS24
Adjustable
Pulley
G3-MS51
Lat Pulldown
G3-MS52
Triceps
Pressdown
G3-MS53
Low Row
G3-MS20
Adjustable Cable
Crossover
G3-MS40
4-Stack
Multi-station
G3-MS50
5-Stack
Multi-station
G3-MS80
8-Stack
Multi-station
Max User Weight 136 kg / 300 lbs.
Product Weight
90 kg /
198.5 lbs.
118 kg /
261 lbs.
80.5 kg /
177.5 lbs.
126 kg /
278 lbs.
399 kg /
880 lbs.
998 kg /
2200 lbs.
1197 kg /
2640 lbs.
1996 kg /
4400 lbs.
Overall Dimensions
(L x W x H)*
68 x 70 x 240 cm /
27 x 28 x 94.5”
126 x 120 x 252 cm /
50 x 47.5 x 99.5”
85 x 59 x 240 cm /
33.5 x 23.5 x 94.5”
230 x 71 x 240 cm /
91 x 28 x 94.5”
397.4 x 90 x 239.6 cm /
156.5 x 35.4 x 94.3”
167.8 x 369.8 x
252 cm /
66.1 x 145.6 x
99.2”
481.5 x 369.8 x
251.7 cm /
189.6 x 145.6 x
99.1”
561.3 x 145.6 x
251.7 cm /
221 x 57.3 x 99.1”
Weight Stack
91 kg /
200 lbs.
134 kg /
295 lbs.
91 kg /
200 lbs.
134 kg /
295 lbs.
2 x 91 kg /
2 x 200 lbs.
2 x 91 kg,
2 x 134 kg /
2 x 200 lbs.,
2 x 295 lbs.
3 x 91 kg,
2 x 134 kg /
3 x 200 lbs.,
2 x 295 lbs.
4 x 91 kg,
4 x 134 kg /
4 x 200 lbs.,
4 x 295 lbs.
* Ensure a minimum clearance width of 0.6 meters (24”) for access to and passage around MATRIX strength equipment.
Please note, 0.91 meters (36”) is the ADA recommended clearance width for individuals in wheelchairs.
PROPER USAGE
1. Do not exceed weight limits of the exercise device.
2. If applicable, set safety stops to appropriate height.
3. If applicable, adjust seat pads, leg pads, foot pads, range of motion adjustment,
or any other type of adjustment mechanisms to a comfortable start position.
Make certain that the adjusting mechanism is fully engaged to prevent
unintentional movement and to avoid injury.
4. Sit on bench (if applicable) and get into appropriate position for exercise.
5. Exercise using no more weight than you can safely lift and control.
6. In a controlled manner, perform exercise.
7. Return weight to its fully-supported start position.
WARRANTY
For North America, please visit www.matrixtness.com for warranty information
along with warranty exclusions and limitations.
MAINTENANCE CHECKLIST
ACTION FREQUENCY
Clean Upholstery * Daily
Inspect Cables Daily
Clean Guide Rods Monthly
Inspect Hardware Monthly
Inspect Frame Bi-Annually
Clean Machine As Needed
Clean Grips * As Needed
Lubricate Guide Rods † As Needed
* Upholstery & Grips should be cleaned with a mild soap and water or a non-
ammonia based cleaner.
† Guide rods should be lubricated with Teon based lubricant. Apply the
lubricant to a cotton cloth and then apply up and down the guide rods.
5
TOOLS REQUIRED FOR ASSEMBLY (not included)
3MM L-Shaped Allen Wrench 10MM L-Shaped Allen Wrench
4MM L-Shaped Allen Wrench Phillips Screwdriver
5MM L-Shaped Allen Wrench 8MM Open-End Wrench
6MM L-Shaped Allen Wrench 17MM Open-End Wrench
8MM L-Shaped Allen Wrench Guide Rod Lubrication
If any items are missing please contact your country’s local MATRIX dealer for assistance.
0 mm 10 20 30 40 50 60 70 80 90 100 110 120 130
UNPACKING
Thank you for purchasing a MATRIX Fitness product. It is inspected before it is
packaged. It is shipped in multiple pieces to facilitate the compact packaging of the
machine. Prior to assembly, conrm all the components by matching them with
the exploded diagrams. Carefully unpack the unit from this box and dispose of the
packing materials in accordance with your local laws.
CAUTION
To avoid injury to yourself and prevent damage to the frame components, be sure
to have proper assistance removing the frame pieces from this box. Please be sure
to install the equipment on a stable base, and properly level the machine. Ensure
a minimum clearance width of 0.6 meters (24”) for access to and passage around
MATRIX strength equipment. Please note, 0.91 meters (36”) is the ADA recommended
clearance width for individuals in wheelchairs.
6
G3-MS24
TECH SPECS
Maximum Training Weight 91 kg / 200 lbs.
Product Weight 90 kg / 199 lbs.
Overall Dimensions (L x W x H)* 68 x 70 x 240 cm / 27” x 28” x 94.5”
* Ensure a minimum clearance width of 914 mm / 36” for access to and passage around MATRIX strength equipment.
TRAINING AREA
3.2
M (
10.5
FT
)
FREE AREA
0.6
M (2 FT)
WIDE PATH
68˚ 68˚
MS24 DIMENSIONS
0.68
M × 0.70 M
(
27
IN × 28 IN
)
Adjustable
Pulley
Adjustable
Pulley
11
22
11
22
Tri ce ps
Biceps
7
Z01
Z02
Z04
Z05
Z06
Z11
Z12
Z13
B25
V03
F01
F02
F03
F04
F05
Z20
Z21
K19
Screw, Oval-Hex Socket (M10x100L)
Arc-flat Washer
Nylon Nut (M10)
Screw, Oval-Hex Socket (M12x25L)
Flat Washer (M12)
Screw, Oval-Hex Socket (M6x45L)
Nylon Nut (M6)
Rubber Stack Cushions
Screw, Oval-Hex Socket (M8x30L)
Sticker, Weight Stack Plate
Pulley (115mm)
Pulley (90 mm)
Bolt, hex-head
Nylon Nut (M10)
Cable
Rubber Tip Weight Shield Bolt
Rubber Shield
Screw, Oval-Hex Socket (M6x15L)
4
8
4
2
2
2
2
2
2
1
3
4
7
7
1
8
8
10
Item Description Qty
NOTE:
Before attaching weight plate decals,
be sure to verify the head plate is
positioned on the weight stack so that
the bolt attaching the pull pin to the
head plate is positioned behind the
chrome adjustment tube.
B25
F05
Z05
Z06
F03x2
F02x2
F04x2
Z05
Z06
Z20x8
Z21x8
F04
F01
F03
F04
F02
F03
K19x2
Z12x2
Z11x2
K19x8
F04
F01
F03
V03
F04
F02
F03
Z13x2
Z04x4
Z02x8
Z01x4
F04
F01
F03
G3-MS24
8
G3-MS51
Lat
Pulldown
Lat
Pulldown
11
22
MS51
TRAINING
AREA
FREE AREA
0.6 M (2 FT)
WIDE PATH
1.2 M
(
47.5”
)
1.26
M
(
50”
)
TECH SPECS
Maximum Training Weight 134 kg / 295 lbs.
Product Weight 118 kg / 261 lbs.
Overall Dimensions (L x W x H)* 126 x 120 x 252 cm / 50” x 47.5” x 99.5”
* Ensure a minimum clearance width of 914 mm / 36” for access to and passage around MATRIX strength equipment.
Loading...