Matica moca espresso User Manual

USER GUIDE

Matica Technologies

April 2015

Users must respect the copyright regulations applicable in their own respective countries. Photocopying, translation, reproduction or transmission of this manual, in whole or in part, for any reason and using any electronic or mechanical means whatsoever, without the prior written permission of the Manufacturer company is strictly forbidden. All contents of this manual are subject to change without prior notice. The Manufacturer accepts no liability for any errors that may be found in this manual, or for any loss or damage that may arise accidentally or as a result of diffusion or use of this manual.

Trademarks

All other trademarks are the property of their respective owners.

Printer Warranty

Refer to the warranty statement provided with the printer for the warranty terms and conditions, and its limitations of liability.

Environmental Impact

Matica is committed to reducing the environmental impact of its products through improvements in energy efficiency.

DIRECTIVE 2002/96/EC ON THE TREATMENT, COLLECTION, RECYCLING AND

DISPOSAL OF ELECTRIC AND ELECTRONIC DEVICES AND THEIR COMPONENTS

1. FOR COUNTRIES IN THE EUROPEAN UNION (EU)

The disposal of electric and electronic devices as solid urban waste is strictly prohibited: it must be collected separately. The dumping of these devices at unequipped and unauthorized places may have hazardous effects on health and the environment. Offenders will be subjected to the penalties and measures laid down by the law.

TO DISPOSE OF OUR DEVICES CORRECTLY:

a) Contact the Local Authorities, who will give you the practical information you need and the

instructions for handling the waste correctly, for example: location and times of the waste collection centres, etc.

b) When you purchase a new device of ours, give a used device similar to the one purchased to our

dealer for disposal.

The crossed dustbin symbol on the device means that:

- When it to be disposed of, the device is to be taken to the equipped waste collection centres and is to be handled separately from urban waste;

Matica Technologies

guarantees the activation of the treatment, collection, recycling and disposal procedures in accordance with Directive 2002/96/EC (and subsequent amendments).

2. FOR OTHER COUNTRIES (NOT IN THE EU)

The treatment, collection, recycling and disposal of electric and electronic devices will be carried out in accordance with the laws in force in the country in question.

For Europe

Warning “This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.”

For US

“This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense”.

Safe for human operation at <20cm usage conditions as SAR exempt under Title 47 CFR Part §2.1093 due to low power transmission.

For Canada

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Safe for human operation at <20cm usage conditions as SAR exempt under RSS-102 Section 2.5.1 due to low power transmission.

Table of Contents

PRODUCT OVERVIEW................................................................................................... 1-1

GETTING STARTED ....................................................................................................... 1-1

Unpacking the Printer ................................................................................................................1-2

Functional Description ...............................................................................................................1-3

Front View ..............................................................................................................................1-3

Operator Panel....................................................................................................................... 1-3

Rear View ...............................................................................................................................1-4

Power Supply......................................................................................................................... 1-4

Plastic Cards.......................................................................................................................... 1-4

INSTALLATION PROCEDURES .................................................................................... 2-1

Installing the Ribbon ..................................................................................................................2-1

Card Feeding .............................................................................................................................2-2

Input Hopper (Automatic Card Feeder).................................................................................. 2-2

Front Slot (Manual Card Hopper)........................................................................................... 2-3

Adjusting the Card Thickness .................................................................................................... 2-3

Connecting the Power Supply and Powering ON the Printer .................................................... 2-4

INSTALLING THE SOFTWARE AND CONFIGURING THE PRINTER.......................... 3-1

Connecting the Printer to the Computer and Installing the Software........................................ 3-1

Add Printer Wizard Program Communication............................................................................ 3-3

USB Connection ........................................................................................................................3-3

Ethernet (LAN) Connection using DHCP.................................................................................... 3-4

Ethernet (LAN) Connection with Fixed IP................................................................................... 3-5

Wi-Fi Connection using DHCP .................................................................................................. 3-7

Wi-Fi Connection with Fixed IP.................................................................................................. 3-9

Uninstall Program Tabs ...........................................................................................................3-11

Add a second printer or change the type of connection .........................................................3-11

Matica Printer Manager ........................................................................................................... 3-11

Using the Printer Manager Instrument Bar with the Mouse................................................. 3-12

Printers Management............................................................................................................... 3-12

Printer Manager .......................................................................................................................3-13

Status Monitor .....................................................................................................................3-13

Preferences .......................................................................................................................... 3-15

Maintenance ........................................................................................................................3-15

Encoding (optional) .............................................................................................................. 3-16

Settings ................................................................................................................................3-16

Updating the Printer Firmware............................................................................................. 3-17

Duplex activation .................................................................................................................3-17

Options ................................................................................................................................3-17

Printer Status Pop-up .............................................................................................................. 3-18

User Guide iii

PRINTING ....................................................................................................................... 4-1

Card Printing .............................................................................................................................. 4-1

Card Printing Using Word ...................................................................................................... 4-1

Double-side Printing .................................................................................................................. 4-2

Color Settings ............................................................................................................................ 4-4

PRINTER MAINTENANCE ............................................................................................. 5-1

Printer Routine Cleaning ............................................................................................................ 5-1

Standard Cleaning ..................................................................................................................... 5-1

Standard Cleaning Procedure................................................................................................ 5-1

Card Path Advanced Cleaning................................................................................................... 5-4

Advanced Cleaning Procedure .............................................................................................. 5-4

Cleaning Roller Advanced Cleaning .......................................................................................... 5-6

Roller Cleaning Procedure ..................................................................................................... 5-6

Printhead Cleaning..................................................................................................................... 5-8

Printhead Cleaning Procedure............................................................................................... 5-8

Printing Test Cards .................................................................................................................... 5-9

Printing a Text Test Card ....................................................................................................... 5-9

Printing Graphic Test Card ....................................................................................................5-9

Printing a Dual-Side Test Card ..............................................................................................5-9

ENCODING OPTIONS .................................................................................................... 6-1

Chip Encoding ...........................................................................................................................6-1

Encoding Test ........................................................................................................................ 6-1

Test ........................................................................................................................................ 6-2

Reading the Chip Encoding ................................................................................................... 6-2

External Encoding...................................................................................................................... 6-3

Magnetic Encoding .................................................................................................................... 6-3

Configuration and Test ..........................................................................................................6-3

Configuration .........................................................................................................................6-4

Test and Encoding ................................................................................................................. 6-4

TROBLESHOOTING ....................................................................................................... 7-1

Printer does not power on .........................................................................................................7-1

Printer has printing problems..................................................................................................... 7-1

RIBBONS ........................................................................................................................ 8-1

CLEANING KITS............................................................................................................. 8-1

TECHNICAL CHARACTERISTICS................................................................................. 9-1

iv User Guide

Printer has problem with ribbon ................................................................................................7-2

Chip Encoding problems ...........................................................................................................7-2

Product Overview

The printer described in this User Guide provides full color dye-sublimation or monochrome thermal transfer printing on standard 54x86 mm plastic cards. PVC, PVC Composite, PET, ABS and PET cards are supported (accordingly with varnished card product configuration). It is managed from the computer through the USB port or via Ethernet/WiFi.

The ribbon carrier, that comes with the printer, allows the ribbon to be replaced quickly and easily.

A number of options are available so that the printer can be configured to operate in different types of environments:

• Magnetic encoder

• Smart Card Encoding Station

• Contact and Contactless Smart Card encoder

• 10/100 Ethernet and/or 802-11 Wi-Fi connection

• Single Card Feed Option

• Connection for external smart card encoding

• Locking system for input Hopper, reject bin and ribbons.

Getting Started

The printer comes with a number of accessories; check carefully that they have been all received. This list may vary depending on the location where the printer will be used.

The printer is shipped in special packaging designed to prevent damage during transportation. If any visible damage is noticed upon reception, contact the dealer immediately.

Maintain the printer packaging intact and store it in a clean and dry place.

Note: If the printer has to be returned, it must be returned integrally with its full original packaging (box,

inner wedges and protective bags). If it is returned without its original packaging and any components are damaged during transportation, such components will no longer be covered by the warranty. Matica will also charge for the new packaging which will be required to ship the printer back

User Guide 1-1

Unpacking the Printer

The following items are included in the box:

• Printer

• Software CD-ROM containing the installer, printer driver and Printer Manager

• The Placemat

• Warranty and Customer Service Information

• Cleaning kit

• Power cord

• Power supply

• USB cable

• Reject bin, optional for Moca (1)

Note: Contact the dealer immediately if any of the items listed above is missing.

Only use the power supply provided with the printer.

e C

1-2 User Guide

User Guide 1-3

Functional Description

Front View

The front of the printer is the operator side and features:

1) Front slot (only when this option has been ordered)

2) Input Hopper

3) Operator panel and printer status indicators: ON/OFF button and a 3-color printer status LED.

Operator Panel

The front operator panel consists of:

1) Soft touch ON/OFF button with a white LED that, when on, indicates when the printer is switched ON:

• Switches the printer ON and OFF; to switch OFF the printer keep this button pressed for a few

seconds.

2) 3-color LED (amber, red and green) indicating the printer’s functional status or an error condition.

• Green

On steady  Printer ready Flashing  Printer receiving data or printing

• Amber

On Steady  Ribbon almost finished Flashing  Operational error: no ribbon or card detected

• Red

On Steady  Mechanical error (cover open, incorrect card insertion or faulty mechanical component) Flashing  Servicing required (during cleaning, heating, cooling or during firmware upgrade)

3) Soft touch WiFi button (for printer models with WiFi module only) with a blue LED:

• Switches the WiFi module ON and OFF

• Blue LED:

On Steady  WiFi connection established Flashing  WiFi data reception/transmission underway

4) Backlit blue stripe: illuminates the Card Hopper to simplify card detection.

Rear View

1-4 User Guide

The following components are located on the back panel:

1) Power cord socket

2) Two USB connectors (Type A and B)

3) Ethernet connector with traffic LED

4) SD card (option) slot

5) Reject bin attachment slots

6) External smart encoder (option) connector

7) Kensington lock.

Power Supply

The printer comes with an external auto-switching power supply.

Note: Only use the power supply provided with the printer.

Plastic Cards

Listed below are the plastic card specifications:

• Type: Composite PVC, PET, ABS (varnished)

• Dimensions: ISO CR80 - ISO 7810 (53.98 x 85.60)

• Thickness: 0.25 to 1.25 mm (10 to 50 mil) manual gauge adjustment

• Magnetic stripe: ISO 7811

• Smart Card Contact: ISO 7816-1,2,3,4

• Smart Card Contactless: ISO 14443A/B.

Installation Procedures

Installing the Ribbon

Original Matica ribbons are to be installed carefully. The ribbon carrier that comes with the printer helps to install the ribbon quickly, easily and accurately. Once the ribbon is in its carrier, the carrier can then be easily dropped into the printer using the yellow guides.

1) Installing the ribbon 2) Insert the ribbon (not provided with the printer) into the ribbon carrier.

3) Open the printing module compartment cover.

4) Insert the ribbon carrier into the printer, looking for the yellow guides that have the same color as the take-up core.

User Guide 2-1

5) Close the printing module compartment cover.

Note: Keep away from the printhead so as avoid damaging it.

Card Feeding

The input Hopper (automatic card feeder) can hold a maximum of one hundred 0.76 mm thick cards. A label inside the door gives the instructions for correctly positioning and orienting the card.

When the single card manual feeder option is present, it can be used without needing to empty the input Hopper.

The card path can be selected via software to speed card processing:

•

Hopper

•

Reject bin.

The output Hopper at the front of the printer can hold a maximum of eighty or thirty 0.76 mm thick cards depending on whether the manual feeder option is present for the Moca model.

Input Hopper (Automatic Card Feeder)

1) Open the Hopper door on the operator panel by pressing at point (a) indicated in the figure below. Load

the cards in the Hopper (b) and then close the door.

bcbcbcbcbcb

2-2 User Guide

Front Slot (Manual Card Hopper)

The manual card feeder is always ready for use and is prioritized. It is suggested that it be used when the job requires a card that different than the ones loaded in the input Hopper.

1) Insert the card into slot (a) indicated in the figure below.

Adjusting the Card Thickness

The card thickness can be adjusted using the wheel inside the input Hopper.

Cards with thicknesses ranging between 0.25 mm and 1.25 mm (10 - 50 mil) can be processed by the printer. Proceed as follows to adjust the card thickness:

1) Open the printing module compartment cover. 2) Rotate the green wheel until the arrow points

to the thickness of the card to be printed.

3) Close the printing module compartment cover.

User Guide 2-3

Connecting the Power Supply and Powering ON the Printer

Connect the power cord to the power outlet, to the power supply and then connect the power supply to the printer as shown below. Press the ON/OFF button to power on the printer.

2-4 User Guide

Installing the Software and Configuring the Printer

The CD-ROM that comes with the printer contains the following:

• Windows Vista, Seven, Win8, Win 8.1 (32 and 64 bit) printer driver for USB, Ethernet LAN and

Wireless connections (if supported by the purchased model)

• Printer Manager application

• PDF User Guide.

Connecting the Printer to the Computer and Installing the Software

1) Power on the computer and then insert the CD-ROM into the drive. Follow the instructions displayed by

the setup program.

Note: Do not connect the printer yet; the setup program will instruct when to do so.

The setup program residing on the CD-ROM executes automatically and the following screen is displayed:

Note: If the setup program does not execute automatically, execute it manually as follows:

• Select System resources

• Select the CD-ROM/DVD drive

• Double click the Setup program.

User Guide 3-1

3) Click “I accept the agreement” to accept the license agreement and then click Next. The following screen is displayed.

4) Click Next to continue. The setup program will request for the destination folder into which the installation files will be stored (the amount of disk space required for the installation is indicated on the bottom of the screen).

5) Click Next to continue. The request for program usage privileges is now displayed. Choose between For all users and For the current user only and then click Next to continue. A screen summarizing the

settings just made is displayed.

6) Click Install to continue. The following screen is displayed upon completion of the installation procedure:

7) Click Finish to continue with the installation. The connection mode screen is displayed.

The installation program automatically executes the Launch Add Printer Wizard by means of which the type of printer connection can be selected. The possible choices are USB, Ethernet/LAN and Wireless (WiFi).

Note: If Launch Add Printer Wizard check box is deselected, the Add Printer Wizard can still be

executed manually from Start > Programs > Matica.

3-2 User Guide

Add Printer Wizard Program Communication

When the CD-ROM software installation is complete, a help Wizard is displayed for configuring the connection mode to be used.

Note: Connection setup can be changed at any time by activating the Wizard mode from the Print

Management Program.

Choose the type of connection required and proceed with its installation.

USB Connection

Click the USB radio button on the Printer Wizard Program screen and then click Next. The following screen

is displayed:

Click Next and wait for the configuration software to recognize the printer and display a message indicating that the installation was completed successfully.

User Guide 3-3

Ethernet (LAN) Connection using DHCP

Click the LAN radio button on the Add Printer Wizard Program screen. The following screen is displayed:

Choose the LAN connection required, selecting either DHCP supplied automatically by the network server or manual insertion on the basis of specific requirements, then click Next.

Note: For more information regarding a specific company network, ask the network administrator. The automatic selection DHCP Network Installation is suggested for the more common installation types.

The following screen is displayed:

Attach the network cable to the printer and then click Next. The following screen is displayed by the configuration software:

If the printer is not found, click Start to search for the network printer and wait until it is found.

3-4 User Guide

Once found, the printer appears in the list of available printers with its related information (IP Address, Printer name, Mac Address).

Click Next and wait for the configuration software to identify the printer and to display a message indicating that installation was successful.

Ethernet (LAN) Connection with Fixed IP

Click the LAN radio button on the Add Printer Wizard Program screen. The following screen is displayed:

Click the Fixed IP Network installation radio button for the manual insertion on the basis of specific requirements, then click Next.

Note: For more information regarding a specific company network, ask the network administrator. The manual selection Network Installation is suggested for the more common installation types.

User Guide 3-5

The following screen is displayed:

Attach the network cable to the printer and then click Next. The following screen is displayed by the configuration software:

Enter the data required for the manual configuration of the network (if part of a company network, it may be necessary to refer to the network administrator for information).

Store the data just entered by clicking Apply Changes and then click Next. The following screen is displayed:

Follow the instructions displayed:

• Power OFF the printer

• Disconnect the USB Cable

• Connect the printer to the network using the LAN cable

• Power the printer back ON again.

3-6 User Guide

Click Next upon completion. The following configuration software screen is displayed:

If the printer is not found, click Start to search for the network printer and wait until it is found. Once found, the printer appears in the list of available printers with its related information (IP Address, Printer name, Mac Address).

Click Next and wait for the configuration software to identify the printer and to display a message indicating that installation was successful.

Wi-Fi Connection using DHCP

Click the WiFi radio button on the Add Printer Wizard Program screen. The following screen is displayed for the search of the SSID wireless connection. Choose the wireless connection available by using the password associated to the WIFI network. The following screen is displayed:

Choose the WIFI connection required, selecting either DHCP supplied automatically by the network server or manual insertion on the basis of specific requirements, then click Next.

User Guide 3-7

Note: For more information regarding a specific company network, ask the network administrator. The automatic selection DHCP Network Installation is suggested for the more common installation types.

WARNING: before proceeding to connect to your wireless network; if necessary you must to manually enter the data of the wireless network (SSID and password).

The settings are displayed. They include the name of the wireless network to which the printer is connected and within which the printer to be installed will be searched for.

Click Next. The following screen is displayed:

Click Start to search for the printer on the network and wait until it is found. Once found, the printer appears in the list of available printers with its related information (IP Address, Printer model, Mac address).

Click Next and wait for the configuration software to identify the printer and to display a message indicating that installation was successful.

3-8 User Guide

Wi-Fi Connection with Fixed IP

Click the Fixed IP Wifi Network installation radio button. Selecting either DHCP supplied manually by the network server or manual insertion on the basis of specific requirements, then click Next.

Note: For more information regarding a specific company network, ask the network administrator. The manual selection DHCP WiFi Network Installation is suggested for the more common installation types.

WARNING: before proceeding to connect to your wireless network; if necessary you must to manually enter the data of the wireless network (SSID and password).

The settings are displayed. They include the name of the wireless network to which the printer is connected and within which the printer to be installed will be searched for.

Click Next. The following screen is displayed by the configuration software:

Enter the data required for the manual configuration of the network (if part of a company network, it may be necessary to refer to the network administrator for information).

User Guide 3-9

Store the data just entered by clicking Apply Changes and then click Next. The following screen is displayed:

Follow the instructions displayed:

• Power OFF the printer

• Disconnect the USB Cable

• Connect the printer to the network using the LAN cable

• Power the printer back ON again.

Click Next upon completion. The following configuration software screen is displayed:

Click Next and wait for the configuration software to identify the printer and to display a message indicating that installation was successful.

3-10 User Guide

Uninstall Program Tabs

To uninstall the software:

1) in Windows XP, select Start > Control Panel > Add/Remove Programs > DCP Version 1.xx.

2) in Windows 7, Windows 8/8.1, select Start > Control Panel > Remove Programs > DCP Version 1.xx.

Note: Alternatively, remove manually the DCP Matica applications.

1) in Windows XP, run the program C:\Programs\Matica\Espresso\unins000.exe

2) in Windows 7, Windows 8/8.1, run the program C:\Program Files (x86)\Matica\Espresso\unins000.exe.

Add a second printer or change the type of connection

On terminating the installation, the program

Add Printer Wizard

appears in the Windows Start menu > All

Programs >

Matica > DCP

Using this program you can run the program Add Printer Wizard Program communication at any time to add or modify a printer connection of type USB, LAN or WiFi.

This allows you to choose the type of connection you want to use without having to repeat the installation from the start, maintaining also a number of printers connected to different communication ports (USB, LAN, WiFi) in the Windows spooler.

Matica Printer Manager

Upon successful installation, the following programs are installed on the computer:

•

Add Printer Wizard

•

Espresso Printer Manager software to manage the printer

•

Setting Up Your Printe in PDF formatr

•

User Manual in PDF format.

User Guide 3-11

Using the Printer Manager Instrument Bar with the Mouse

The Windows toolbar includes the Matica application logo that, when clicked, displays a popup window from where the Printer Status can be launched. Left-clicking the related icon on the instrument bar opens the Printer Manager program.

Right-clicking the related icon on the instrument bar opens the Windows menu popup program.

The menu consists of the following:

• Printer Manager: Opens the Printer Manager program

• Where To Buy: Opens a web browser with a link to the Matica Technologies commercial website

• Popup Print Errors

• Popup Job Status

• Quit: closes the program.

Printers Management

The Printers Management window is displayed, as shown below, when the program is executed from the Application bar or from Windows programs.

All the printer drivers installed on the computer are displayed in this window. From here, the Printer Manager can be launched for a given printer by double-clicking on the related printer name.

The following information is available in this window:

1) Printer Name: the name of the printer is displayed in this area. The printer name can be defined by the user during the installation; if is not defined by the user, it will be defined from the program during the installation in which case it will be composed of the printer name and the port where it was connected during installation.

Double clicking the printer name opens the Printer Manager.

2) Connection: the following connectivity is supported:

USB (Local Connection)

WiFi Access Point (Printer Internal Router)

LAN (cable)

WLAN (WiFi).

3) Printer Status: this area can provide the following information:

- Matica Logo or Printer model logo

- WiFi connection logo; the printer is connected via WiFi

- Printer status with background color:

a) Green: Ready – Standby

b) Light Grey: Off-line

c) Amber: Job underway – Error (with a brief description of the error)

4) Ribbon Type: when the printer is connected, this area indicates the type of ribbon installed in the printer.

5) Remaining Capacity: this area indicates how much ribbon is still available. Once a printer is chosen and the Printer Manager is opened after double-clicking on the printer name, the Printer Management window reduces to an icon. To then reopen the Printer Management window, proceed as explained at the beginning of this section.

3-12 User Guide

User Guide 3-13

Printer Manager

Open the Print Manager by double-clicking in the Application bar icon .

1) Information regarding the printer installed, or on its configuration, is displayed in this area.

These contents are associated to the icon button displayed on the left hand-side of the window.

The following Printer Manager function icon buttons are provided:

•

Status Monitor

•

Preferences

•

Maintenance

•

Encoding (only for the models supporting this feature)

•

Settings

•

Help.

Click Back to return to the printer management window.

Note: The Encoding icon will be displayed only when the Encoding option is available.

Status Monitor

Open the Status Monitor by clicking on the icon . The card settings and printing options can be

configured here.

The following information areas are available: 1) Printer Status – 2) Ribbon Status - 3) Job List.

3-14 User Guide

Printer Status Area

The printer status and error or warning messages are displayed in this area. The possible conditions are: Ready, Busy, Disconnected.

Ribbon Status Area

Ribbon-related information is displayed in this area.

1) Type of ribbon installed.

2) Ribbon Preferences button: click this button to open the printer driver’s Media tab from where the ribbon

settings can be changed.

3) Remaining ribbon capacity indicator: this indicator shows a percentage of how much ribbon can still be used.

Indicator color:

- Green: from 100% to 21% remaining

- Yellow: from 20% to 11% remaining

- Red: from 10% to 1% remaining

- Empty bar, flashing: 0% remaining (error condition)

4) Graduate scale representing the percentage.

Job Status Area

A job queue is displayed in this area when a printing is underway.

User Guide 3-15

Preferences

Open the Preferences by clicking on the icon .

This button to run the printer driver user interface program from where Printer Preferences and other printer parameters can be set. It provides a short-cut to the printer driver program without having to exit the Printer Manager. The first tab displayed by default is the Card tab.

1) Card Type: set the type of card.

2) Card Path: select the output and the reject bin for the card to print.

3) Print Orientation: select the orientation (portrait, landscape, 180° rotation) and the print on both sides.

Click OK to store the user settings, click Restore Default Settings to clear the user settings and restore the factory default settings.

Maintenance

Open the Maintenance by clicking on the icon . From this area you can test the print quality using the

test card layouts and launch the printer cleaning routine.

In this environment you can run:

1) Test Card, for printing a test card – 2) Cleaning, for standard or advanced card cleaning.

Click on Back to return to the Status Printer screen.

3-16 User Guide

Encoding (optional)

Open the Encoding by clicking on the icon . If available, this feature enables magnetic encoding and

the retrieval of the Smart Card ATR number.

The following can be defined in this area:

1) Magnetic encoding: test the module and single card read/write on the magnetic stripe of the card

2) Chip encoding: test the module and read the ATR of smart cards.

Note: Refer to Chapter “Encoding option” for more information.

Settings

Open the Settings by clicking on the icon . Duplex activation, Energy Savings, Firmware Updates and

Options can be configured in this area.

1) Energy saving parameters.

2) Firmware Update.

3) Duplex activation settings.

4) Options installed on the printer.

Click Back to return to the Printer Status screen.

Energy Saving

Set the energy saving features in this area. Selecting or deselecting the Enable Energy Saving check box enables or disables, respectively, the Energy Saving area. When disabled, the default timing is set by the FW to 5 minutes and is displayed in grey. (Default: Enabled).

Sleep

Selecting or deselecting the Enabled check box enables or disables, respectively, the Sleep feature.

If Sleep is disabled, Standby mode also is disabled, and therefore the sleep time is set to the factory default value of 5 minutes. To set the time field when Sleep is enabled, set the value using the sidebar arrow buttons or enter the value directly. The selectable range is from 1 to 240 minutes, in steps of one minute.

Standby

Selecting or deselecting the Enabled check box enables or disables, respectively, the Standby feature.

Standby mode is active only if Sleep mode is enabled. When Standby is enabled, set the time using the sidebar arrow buttons or enter the time directly. The selectable range is from 1 to 1440 minutes, in steps of one minute. Note: A time less than or equal to the standby time is not allowed.

Updating the Printer Firmware

Open the Printer Manager Program and click the Settings button. The Settings screen is displayed. The printer firmware can be updated in this area.

The Version Installed field shows the current version of the printer firmware. Click Firmware Update to launch the Update Firmware wizard.

Duplex activation

Two-sided printing can be enabled in this environment (for more information refer to the documentation provided with the option).

Options

Options Installed: Codes of the options installed.

User Guide 3-17

Printer Status Pop-up

The Printer status pop-up consist of a card window containing several areas that the software compiles in real time every time the pop-up needs to be displayed.

1) Printer Nam

area: the printer’s default name or its name assigned during installation is displayed in

this area.

2) Status Description area: the error code or error description is displayed in this area.

3) Status Solution Area: the troubleshooting message related to the error detected and displayed in the

Status Description Area, is displayed here.

4) Utility Command Bar: displayed only when the Pop-up is static and user intervention is required. The status error table describes how the utility bar is managed.

: click to resend a print job once an error condition is cleared. Clicking this button causes the

pop-up to disappear; if the error is not cleared the pop-up will be displayed again.

: click to remove a print job from the printer spooler.

3-18 User Guide

Printing

Card Printing

Cards are usually printed and encoded by a Printer Application chosen by the User. However, if required, a compatible non-proprietary Application is available as an option for designing and printing cards. Cards can be customized (logo, image and name) by creating graphic images and defining page formats.

The Printer Application recognizes the printer, allowing the User to create fully customized card jobs.

Card Printing Using Word

There are a large number of Windows applications that allow document printing (for example Microsoft Office® suite tools such as MS-Word®, MS-Access®, MS-Excel® and MS-PowerPoint®).

An example is provided below:

Using Microsoft® Word

1) Run the MS-Word application. In the Menu bar, click File then Page Setup.

2) In the Card tab, select the card Size option followed by the custom format 55x85 mm (default format).

3) If using Word 2010/2013: select the Page Layout tab. For Size, select Custom format.

4) In the Margins tab, set all margins to ‘0’ and select Landscape for the Orientation.

5) Close the window by clicking OK.

6) The card can now be customized by adding the various items composing the card:

- Logotype, illustrations, Identification photo

- Fixed and variable texts

- Barcode, etc.

Once the operation is complete, click File followed by Print.

7) Click Print or click on the printer icon. Select Matica printer.

8) Select Properties to customise the print options from this screen:

9) Select the Output choosing between Output Hopper or Rear Bin.

User Guide 4-1

10) Click the Media tab to configure specific settings such as:

• Ribbon Identification

• Color Panel Adjustment (brightness, contrast, sharpness)

• Overlay Panel Adjustment

• K Panel /Monochrome Adjustment (greyscale, black text, etc..)

Note: If necessary, configure the settings in the Configuration tab to enable use of particular options or additional accessories installed on the printer.

Double-side Printing

1) Select Properties from this screen to customize the printing options:

2) Check the box selection Dual side printing for front and back printing.

3) Click OK to store the settings made and print the card.

Note: Two-sided printing is optional (installation of the Duplex Kit is required).

4-2 User Guide

If Dual-sided printing was selected, by clicking the Media tab of Printer Preferences the following parameters for the two sides of the card can be selected independently:

• Color Panel Adjustment (brightness, contrast, sharpness)

• Overlay Panel Adjustment

• K Panel /Monochrome Adjustment (greyscale, black text, etc..)

Note: The Back Mode button default selection optimizes the consumption of the ribbon installed in the

machine. A different setting other than the default can be selected but this means enabling the printer to consume a greater amount of ribbons.

User Guide 4-3

Color Settings

To customize color printing, click Printer Driver Properties and then click the Color Settings tab.

You can modify the saturation of each colour being printed by moving its related cursor.

When the cursors are moved, the image with the coloured pencils illustrates how the settings change.

However, to be sure that the actual result obtained meets your expectations, it is necessary to run a few print tests.

Click Defaults to restore the factory default settings.

4-4 User Guide

Printer Maintenance

Printer Routine Cleaning

Four different cleaning processes are implemented in the printers.

Standard Cleaning

Suggested frequency:

•

Color printing: Each time the ribbon is changed

Mandatory frequency (to prevent voiding the warranty)

•

Every 1,200 cards printed.

Standard cleaning is performed using the specific cleaning card as explained below. The product has an internal counter that keeps track of the number of cards printed and warns the user

when the mandatory cleaning procedure must be performed.

Standard Cleaning Procedure

1) Open the printing module compartment cover. 2) Remove the ribbon carrier.

3) Close the printing module compartment cover. 4) Use the cleaning card CR80 (A) or the extended

Card (B). Remove all the protective film.

Extended card (B)

CR80 (A)

User Guide 5-1

5) Insert the cleaning card (A) in the rear slot of or insert the extended card (B) in the rear slot of

the printer. the printer as represented in Figure. The adhesive surface should remain at the The adhesive surface is on both sides. top.

6) Open the Printer Manager and click the Maintenance button.

The Maintenance window is displayed.

5-2 User Guide

7) The counter indicates the number of cards that have been printed starting from the last cleaning operation performed. Click the Standard Cleaning button to start the cleaning procedure. Once the cleaning procedure is completed, the card is ejected from the rear slot and the counter is reset.

8) Open the printing module compartment 9) Insert the ribbon carrier.

covers.

10) Close the printing module compartment covers. 11) The Standard cleaning procedure is terminated

and the printing counter is reset to zero.

User Guide 5-3

Card Path Advanced Cleaning

The card path advanced cleaning procedure is required after performing five Standard cleaning procedures:

• The special (alcohol impregnated) T-card must be used.

• The procedure involves cleaning the card path, removing the dust on the rollers and cleaning the

magnetic head.

• The printer has an internal counter that stores the number of Standard cleaning procedures

performed, so as to notify when the Advanced Cleaning procedure is required (see the Printer Manager Specifications).

• A software-guided procedure will assist in carrying out the cleaning operations.

Advanced Cleaning Procedure

1) Open the printing module compartment covers. 2) Remove the ribbon carrier.

3) Close the printing module compartment 4) Insert the T-card into the rear slot of the printer.

covers.

5-4 User Guide

5) Open the Printer Manager and click the Maintenance button. The Maintenance window is displayed.

6) The counter indicates the number of cards that have been printed starting from the last cleaning

operation performed. Click the Advanced Cleaning button to start the cleaning procedure. Once the cleaning procedure is completed, the card is ejected from the rear slot and the counter is reset.

7) Open the printing module compartment covers. 8) Insert the ribbon carrier.

User Guide 5-5

9) Close the printing module compartment covers. 10) The advanced cleaning procedure is now

concluded and the printing counter is reset to zero.

Cleaning Roller Advanced Cleaning

It is suggested to perform an advanced cleaning of the cleaning roller when the standard cleaning procedure does not efficiently remove all the dust from the cleaning roller.

Roller Cleaning Procedure

1) Unplug the printer from the power supply.

2) Open the printing module compartment covers. 3) Remove the ribbon carrier.

5-6 User Guide

4) Identify the roller. 5) Remove the roller by extracting it parallel to

the printing module and slightly upwards, until hearing a release click.

Clean the roller using water and dry it.

7) Reinsert the roller, pushing it into its seat, 8) Insert the ribbon carrier.

pressing downwards and parallel to the

surface of the printing module.

9) Close the printing module compartment 10) The roller cleaning procedure is now concluded.

covers.

User Guide 5-7

Printhead Cleaning

It is suggested to clean the printhead when dots are missing on the printed cards:

• The edge of the printhead must be cleaned using the special impregnated swab or the cleaning pen.

• The edge of the printhead must be cleaned to remove residual ink or dust.

Printhead Cleaning Procedure

1) Unplug the printer from the power supply.

2) Open the printing module compartment covers. 3) Using the cleaning swab that is provided

in the Cleaning Kit, clean the printhead by rubbing the swab it in the direction indicated by the arrow in the figure below.

4) Close the printing module compartment covers. 5) The printhead cleaning procedure is now

concluded.

5-8 User Guide

Printing Test Cards

Test Cards are used to check that the printer is operating correctly and to obtain some important printing parameters.

Open the Printer Manager and click the Maintenance button. The following screen is displayed.

Printing a Text Test Card

In the Test Card area, click the Monochromatic button to launch the Text Test Card print quality test. Used mostly when a monochrome ribbon is installed or to test the black panel in a multi-panel ribbon.

Printer information is printed on the Text Test Card.

Printing Graphic Test Card

In the Test Card area, click the Color button to launch a Graphics Test Card print quality test. It is mainly used when a multi-panel ribbon is installed.

Printing a Dual-Side Test Card

In the Test Card area, click the Dual Side button to launch the Dual-Side Test Card print quality test. The button is only displayed when the Printer Manager is installed on a printer with the dual-side option.

User Guide 5-9

Encoding Options

Chip Encoding

The Chip Encoder is an optional module for the Espresso products that allows the encoding of chip cards (smart cards).

Available chip encoding modules and related functionalities:

• CHIP ENCODING STATION COMBO PCTWIN +

OMNIKEY

Allows yo

u to run chip encoding on contact cards (via Chip PCTwin) and on cards wi

out contacts (via Chip Omnikey) Code PR000015

• CHIP ENCODING STATION CONTACT PCTWIN

Allows you to run chip encoding on contactless cards only (via Chip PCTwin) Code PR000024

• CHIP ENCODING STATION CONTACT OMNIKEY

Allows yo

u to run chip encoding on contact cards only (via Chip Omnikey) Code PR000025

• CHIP ENCODING STATION CONTAC

TLESS OMNIKEY

Allows yo

u to run only on chip encoding contactless cards (via Chip Omnikey) Code PR000026

• CONTACT STATION AND EXTERNAL ENCODER CONNECTION

Allows you to run chip encoding using an encoding system off the printer Code PR000020

• CONTACT STATION FOR CHIP ENCODING

Allows you to run chip encoding with user-selected. Encoder boards other th

an those proposed by Matica Code PR000223

Install the module according to the instructions contained in the package.

Encoding Test

Warning: Before proceeding with the configuration of the module make sure the printer is turned on and

connected to your computer via USB.

Warni

ng: before proceeding with encoding operations, download the driver compatible with the O.S: used

in the PC from the site of the encoder board manufacturer.

User Guide 6-1

6-2 User Guide

Test

Open Printer Manager and click the Encoding button. The following screen is displayed from where it is possible obtain the Smart Card ATR number.

Reading the Chip Encoding

This area provides the ATR number of the contact card. This operation is performed to ensure that the contact encoder is working correctly.

Selecting

the Encoder option from the drop-down list, choose the type of encoder you require. If only one

encoder is available, this option is not active.

1) Load Button

Click to start a batch job, consisting of

Taking the card from the selected or default input (see card path in the printer driver Card tab)

b) Moving the

card to the contact encode

2) Read ATR Button

Click to rea

d the contact card’s ATR number. For the ATR Number to be read, the card must be positioned in the contact encoder by clicking Load. The encoder then reads the card and displays the ATR number in the window. The encoder reads and displays the ATR number until clicking the Eject button, at which point the card is moved from the encoder to the output specified for the card path

(see card path in the printer driver Card tab

3) Eject Button

Click to move

the card that has been left inside the printer to the selected or default output. (

see card path in

the printer driver Card tab

External Encoding

The machine configured with an external encoder is equipped with a specific 12-pin connector, configured in the following way:

Pin Name Description

1 C8 RFU

2 C4 RFU

3 C7 I/O

4 C3 CLOCK

5 C6 VPP

6 C2 RESET

7 C5 GND

8 C1 VCC=5V

9 CDD_NO CARD DETECT NO

10 CDD_NC CARD DETECT NC

11 Free

Binder female socket 12 ways

black connector 720 series

p/n 99 9136 00 12

Free

A sequence of commands must be sent via the printer interface to insert a card into the printer, position it under the station and establish contact. Sending the command sequence:

• A card is moved automatically from the feeder to the encoding station and stops. The contact station is

pushed downward to make contact with the ca

•

The chip can be programmed via the external coupler.

Magnetic Encoding

The Magnetic Encoder is an optional module for the Espresso and Moca products that allows the encoding of magnetic cards.

The following modules are available:

• MAG ENCO

DER ISO

It allo

ws you to perform the encoding magnetic in ISO format Code PR000023

• MAG ENCO

DER JIS2

It allo

ws you to perform the magnetic encoding format JIS2 (Japan

) Cod

e PR000018

Install the module according to the instructions contained in the package.

Configuration and Test

Warning: Before proceeding with the configuration of the module make sure the printer is turned on and

connected to your computer via USB.

User Guide 6-3

6-4 User Guide

Configuration

To print using the Magnetic Encoder, enable these modules on the printer so that the printer driver can use them correctly.

1) Set the Coercitivity values from High, Low.

Set the "Standard" encoding preferences. With this drop down menu is possible to set which standa

to u

se for encoding the cards. These are the possible choices: ISO (Default) - ISO 7811 Standard or JIS-

2 - Japanese JISB9561-1979 Standard.

Tracks (ISO Standard), With these commands, for every single track, is possible enable / disable t

ack and make the ISO Standard choice

Track 1, Track2, Track 3: with the selection boxes is possible enable/disable the tracks, with the drop down box is possible choose the standard ISO. The possible choices of Standard ISO in the drop down menu are:

Standar

d Track 1 Track 2 Track 3

ISO1 DEFAULT ISO2 DEFAULT ISO3 DEFAULT

Tracks (JIS-2 Standard): If the JIS-2 standard is choose appear only the track 1 and in the drop down menu is possible only chose the JIS-2 standard. The possible choices of JIS-2 standard in the drop down menu are:

Standard Track 1

JIS-2 DEFAULT

4) Mag strip start/end sentinels: with these command is possible to set the “Special Character Strings”

used for the in-line magnetic encoding. These special characters are placed at the beginning and e

nd of the characters that we want to write in the magnetic fields, for more details please refer to the rule ISO7811. Every Start and end sentinel must have the possibility to manage until of 3 characters each. In the drop down menu there are two type of choices:

• Def

ault: the strip start/end sentinels Characters are the Standard DCP and they are not editable.

• Personalized: the strip start/end sentinels Characters are editable by the user. In the "begin" and "end" boxes is possible display or set the specials characters. Every row correspond to a track. For each track, you can use up to a maximum of three characters, always followed by the track number as follows:

track 1: start= -%1 end=? track 2: start= -%2 end=? track 3: start= -%3 end=?

User Guide 6-5

Test and Encoding

The magnetic card is read and written in the magnetic encoding area.

1) The Tr

ack Area contains the fields (ISO Standard or JIS-II Standard) where the magnetic tracks can be

read or written

Printer Driver

Track Status

Track Label

Track Window Result Box

Enabled Black

Active (inside, the text displayed in grey shows how the track is

set for the printer driver)

Active (empty)

Disabled

Grey light

Not Active, the background is slightly grey (inside, the text displayed

in light grey shows how the track is set for the printer driver)

Not Active

(empty)

When the read mode is selected, the characters read are displayed in the Read/Write window. When the write mode is selected the characters to be encoded are written in this window. In the write window, certain checks have to be performed on the characters typed. Characters have to be compatible with the ISO or JIS-II standard chosen for the printer driver, otherwise an error message is displayed.

2) Load Button

Click to start a batch job, consisting of:

Taking the card from the selected or default input (see card path in the printer driver Card tab)

Moving the card to the magnetic encoding area.

3) Encode button

Click to encode a magnetic card.

To encode the card, it must firstly be positioned in the magnetic encoder by clicking Load.

Card encoding: for the enabled tracks, reads the characters written in the track window and encode

them.

The results window displays whether the operation was executed correctly or not.

Upon completion of the card writing, the card remains in the magnetic encoding area until clickin

Eject,

at which point the card is then ejected to the specified card path

d) If an error occurs during encoding, the card is sent to the Reject

bin.

4) Read Button

Click to read a magnetic card.

To read the card, it must firstly be positioned in the magnetic encoder by clicking

Load

For enabled Tracks, it displays the value read in the track windows. In the results window, it indicates whether the operation was executed correctly or

not.

Upon completion of the card reading, the card remains in the magnetic encoding area until clicking

Eject

, at which point the card is then ejected to the specified card path.

5) Eject Button

Click to move the card that has been left inside the printer to the selected or default output

(see

card path in the printer driver Card tab).

User Guide 7-1

Trobleshooting

Printer does not power on

Printer has printing problems

Printer does not power on

USER

Disconnect and reconnect again the power cables making sure

that an electricity supply is actually present

Printer does not start

printing (no movement)

USER

• Make sure that a Moca/Espresso printer appears in “Devices and Printers” and that it is active (icon appears in dark grey)

• Make sure that options “popup prints error” and “popup jobs status” are selected

• Make sure that card is present in the input hopper

• Make sure that the front panel (output bin) is closed

• Make sure that the ribbon is actually loaded and that its

cover is fully closed

Executes movements but

card is not printed

(blank card)

USER

• Make sure that the ribbon cartridge is inserted correctly

• The identifier of the ribbon has been damaged and as a

result cannot be used by the machine: change the ribbon

Defects in Print Quality

USER

• Single or Multiple horizontal lines: clean the printhead using a swab or pen as described in the User Manual

• Dots appear on printout due to dirty cleaning roller: clean with water as described in the User Manual

• Partial printing or dots due to dirty cards: use only clean cards

• If printout colours or appearance are not satisfactory, modify the Brightness, Contrast and Sharpness values in Printer Preferences and check printout improvement

• Red marks appearing on printouts: these may occur when printing dark images with high contrast and brightness settings. To eliminate them, reduce the “contrast” and “brightness” values in the “colour settings” menu on the “ribbon/preferences” page

7-2 User Guide

Printer has problem with ribbon

Chip Encoding problems

Printer takes up the card

but remains blocked

USER

• The card thickness setting does not correspond with that of the card being used: set the correct value, remove the card, then switch the printer off and on again.

• If you are using non-original ribbon, check that the type of ribbon set for the driver corresponds with the one actually being used

• Flip Over not in position: switch off the machine, remove by hand any card left in the flip over, then switch the printer on again

• The weight of the input hopper does not rest on the card in the tray or is missing. Free the weight or introduce it

• Check that the cleaning roller is not out of place. If it is, switch off the machine, put the roller back into position and switch the machine on again.

• Check that no ribbon fragments are present in the card path. If there are, switch the machine off and remove them, then switch the machine on again

• Check that no card is present in the path. If there is, switch the machine off, remove the card, then switch the machine on again

If the ribbon has tears or

locks with error 14

USER

• lower the “contrast” and “brightness” values in the “colour settings” menu on the “ribbon/preferences” tab

Difficulties or failures in

the code reading ATR

USER

• Open the “Devices and Printer” window and select the “USB smart card reader” device

• Select the “Hardware” “Properties” of the device, then go to the “Power Management” tab

• Remove the flag on the line “allow the computer to turn off the device to save power”

Ribbons

The following Matica ribbons can be used:

Ribbon Type Code to order

Monochrome BLACK-2000 : 2000 prints, standard quality

PR000034

Color YMCKO : 200 prints

PR000032

YMCKO : 250 prints -

NOT available for MOCA

PR000031

Color 1/2 YMCKO : ½ 400 prints

PR000166

YMCKOK: 200 prints

PR000033

Monochrome KO-600: 600 prints

PR000165

Monochrome RED-1000: 1.000 prints

PR000098

Monochrome BLUE-1000: 1.000 prints

PR000100

Monochrome GREEN-1000: 1.000 prints

PR000099

Monochrome WHITE-1000: 1.000 prints

PR000101

Monochrome SILVER-500: 500 prints

PR000162

Monochrome GOLD-500: 500 prints

PR000163

Each Matica ribbon has an RFID tag with ribbon identification data that allows the printer to configure all the counting and optimization parameters and procedures.

It is strongly suggested to exclusively use original Matica ribbons. The use of non-original accessories could damage the product and therefore void the factory warranty.

Cleaning Kits

The following Cleaning Kits can be used:

Cleaning Kits Code to order

Standard Cleaning Kit: 5 cleaning sticky cards and 5 cleaning swabs

PR000196

Advanced Service Cleaning Kit: 2 cleaning T-cards, 2 cleaning sticky cards, 1 cleaning pen

PR000197

User Guide 8-1

Technical Characteristics

• Single-side or dual-side (*) printing module

• Edge-to-edge printing

• Color dye sublimation and monochrome thermal transfer

• 300 dpi printhead (11.8 dots/mm)

• Up to 128MB of RAM

• Drop-in ribbon carrier

• User-friendly features for easy-to-use functionality and maintenance

Connectivity*

• High-speed USB 2.0

• Ethernet TCP-IP, 10BaseT, 100BaseT with Traffic LED (*)

• WiFi IEEE 802.11 b/g (*)

• SD card slot (*)

• Round connector for external encoding (*)

Card Management

• 100 card capacity in automatic input Hopper (0.76 mm – 30 mil)

• 30 or 80 (*) card capacity in output Hopper (0.76 mm – 30 mil)

• Exception card manual feeder (*)

• Rear bin (*)

• Card types: PVC and composite PVC cards, PET cards, ABS cards (*)

• Card thickness: 0.25 to 1.25 mm (10 to 50 mil)

• Card format: ISO CR80 - ISO 7810 (53,98 mm x 85,60 mm)

Ribbons

• Automatic detection and parameter setting

• Smart Ribbon level memory and management

• Smart Ribbon optimization in monochrome printing

• Available ribbon: please refer to Matica website: www.maticatech.com

Print Speed

• Single-side Monochrome: up to 850 cph (*)

• Single-side YMCKO: up to 210 cph (*)

• Dual-side YMCKO-K: up to 140 cph (*)

Encoding (*)

• Magnetic encoder (read/write) 3-track HiCo/LoCo ISO 7811 and JIS II

• Smart card contact station ISO 7816-1, -2 (excluding Appendix B), -3, -4

• Contact/Contactless encoders compatible with std Cards MIFARE®, MIFARE DESFire® iCLASS®

ICODE, ISO 14443 A&B, ISO 15693 and ISO 7816

User Guide 9-1

Software

• Printer driver

• Printer Manager

• Automatic Installer

• Compatible with Windows: XP SP3; W7 32/64 bit, W8.x 32/64 bit

Security

• Slot for Kensington® lock

• Lockers with keys for input Hopper, rear bin and ribbon (*)

Power Supply

• Auto-switching external power supply unit with interchangeable power cords

• Input 100-240 Volts AC, 50-60 Hz, 1.5 A

• Output 24 Volts DC, 3.0 A

Dimensions and Weight

• Dimensions (H x W x L): 253 x 200 x 395 mm

• Weight: 6.6 kg

Quality Standards

• CE

• Standby mode and reduced power consumption

• Sound pressure less than 48 dB (A) in operation mode (ISO 7779)

• Min/max operating temperature: 15° / 30 °C (59° / 86 °F)

• Humidity: 20% to 65% non-condensing

• Min/max storage temperature: –5° / +70 °C (23° / 158 °F)

• Storage humidity: 20% to 70% non-condensing

(*) Only in some models/options

9-2 User Guide

DECLARATION OF CONFORMITY (according to ISO/IEC 17050)

Manufacturer: Matica Technologies AG

Address: Teckstraße 52

Germany - 73 734 Esslingen am Neckar

Equipment category: Information Technology Equipment Product type: Card Printer

Models: ESPRESSO,

MOCA XXXXX (X = A-Z, 0-9 or BLANK)

The undersigned hereby declares, on behalf of Matica Technol

ogies AG, that the abovereferenced product, to which this declaration relates, complies with the following council directives and harmonized standards.

Council Directives: 1999/5/EC relating to radio and telecommunications terminal

equipments

2006/95/EC Low Voltage Directive 2004/108/EC EMC Directive 2011/65/UE ROHS Directive

Harmonized Standards: EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011

Information technology equipment – Safety – Part 1:General requirements

EN 55022:2010 Information technology equipment– Radio disturbance characteristics– Limits and methods of measurement

EN 55024:1998 + A1:2001 + A2:2003 Information technology equipment - Immunity characteristics Limits and methods of measurement

E N 61000-3-2:2006 + A 1 : 2 0 0 9 + A 2 . 2 0 0 9 Electromagnetic compatibility (EM C ) - Part 3: Limits – Section 2: Limits for harmonic current emissions (equipment input current ≤16 A per phase)

EN 61000-3-3:2013 Electromagnetic compatibility (EMC). Part 3: Limits. Section 3: Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection

Year of CE marking: 2014 Date and place of issue: 17.10

.2014

Typed name and position of a

uthorized person Signature of authorized person

Haral

d Zi

VP Marketing and Training

roduct ode CM00000154en revision C

Matica moca espresso User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual