Match MS 42C, MS 62C, MS 52C, MS 6X, MS 5X User Manual

a.

CD

c:

(i)

(')

";j'

-

MS

MS

Komponenten-

Component-

62C

6X

I

MS 52C

I

MS

und

and

Koaxiallautsprechersysteme

coaxial

SX

I

MS 42C

I

MS

speaker

4X

systems

Dear Customer,

Congratulations on your purchase

of

quality MATCH speaker system.

This system highlights best quality,

excellent

facturing and state-of-the-art technology.

research & deve-

After

30

years

experiences

of

in

this high-

manu-

audio products this speaker system ge-

lopment

of

neration sets new standards.

We wish you many hours

of

new MATCH speakers.

Yours
AUDIOTEC FISCHER

Team

enjoyment with your

General instructions for

installing

a MATCH

speaker system

prevent damage to the speakers and possible in-

To
jury, read this manual

carefully and

follow all

instal­lation instructions. This product has been checked
for proper function prior to shipping and is guaran­teed against manufacturing defects.

For a proper performance and to ensure

full war­ranty coverage, we strongly recommend to get this
product
If
the
Failure to

installed by an authorized MATCH dealer.

you choose to perform your own

installation

following information and precautions

follow

the stated precautions may result

read

carefully.

in

personal injury and/or damage to the audio system

vehicle.

or

fit into

Always make sure that the speaker

1.

will
the intended mounting location and that there
is adequate depth for the magnet system.

Check for adequate space between spea-

2.
ker and window, window crank, power win­dow mechanism, seat, rear deck torsion
bars, and other items which may interfere
with the speaker's mounting. This is very
important if any hole cutting is required.
Detailed size information is indicated

this manu-

the dimension section

in
al.
face is flat

Take care that the mounting sur-

and free from

of

obstructions.

all

the

4. The quality

of

ficant effect on the overall

installation

has a signi-

performance
the speaker system. Treat each installa­tion step with a high degree

5.

Avoid low frequency

cancellation

of

by air leakage between the speaker
basket and the mounting surface (e.g.

mounted on a bended or uneven sur-

an oversized hole).

face or mounted

6.

Mounting panel

cessary

some cases

in

in

reinforcement may be ne-

order to ensure a

in
stable , torsion-free and even surface. This
can be achieved by mounting the spea-

ker on a

hind the body

installation

most cases you can use the original spea-

In

7.

metal

or wooden sub-baffle be-

panel. Consult an

door

or

specialist for further advices.

ker mounting locations at the doors, body pa-

these are not

or the rear deck.

nels

If
you have to prepare your own secure
tion place. Due to their structural integrity and
accessibility the precut mounting holes
be used whenever possible.

Important:

that is an integral part

Never cut any

metal

automobile's safety or structural car body.

of

attention.

caused

available

installa-

should

an

of

Do not mount the speakers where water may

3.
splash on them.

7

General instructions for connecting MATCH
speaker systems

General

instructions for mounting MATCH spea-

ker systems

strongly

We

audio system at low volume

plete
stallation.
securing the loudspeakers into their mounting
tions.

Make sure that

from cutting or wear at sharp edges. This can

into a short circuit which might damage your head

amplifier

unit,

Make sure that
length
thout stress on the wire or connectors.

recommend that

This will allow

speaker wiring is

all

and/or

order to reach the speaker

in

speaker system.

speaker wires have sufficient

all

you operate the com-

before

trial listening test before

a

fully

final in-

protected

terminals

loca-

lead

wi-

Once you have tested the
and have confirmed correct operation, turn off the
audio system and prepare the loudspeaker for
mounting.

Place

1.
on as shown
woofer".
Fix the speaker with its mounting ring in its in-

2.
stallation place
the right position to the fixing
included
Tighten all
Attach the mesh to the mounting ring.

3.

the loudspeaker in the mounting positi-

in

screw

screws

complete

the illustration ,Mounting the

and check if

to secure the screws.

clips

evenly.

speaker system

final

screws are

all

holes. Use the

in

Component systems

2-way component system with reduced moun­ting depth for easy
Woofer with high damping coated paper cone

silk

1"

25 mm
neodymium magnet
Separate, compact crossover with high-grade
components and tweeter protection
Grille, cables

in

I

delivery

installation

dome tweeter with

and mounting

material included

Coaxial

systems

2-way coaxial system with reduced mounting
depth for easier installation
Woofer with high damping coated paper cone

Integrated tweeter with

neodymium magnet

Grille, cables

delivery

in

and mounting material included

polymer

dome and

8