Mastervolt SmartRemote Installation Manual

Specifications

Model:
Product code retail:
Product code OEM:

Dimensions:
Screen:

Weight:
Operating temperature:
Relative humidity:
Storage temperature:
Power supply:
Power consumption:
Protection degree:
Approvals:
Interfaces:

For additional information, like supported devices,
please visit our website: www.mastervolt.com

10000015712/02

SmartRemote
77010600
77010500

72×72×30 mm/2.8×2.8×1.2"
320x240 pixels,
16 bits color, 2.8"
75 g / 2.6 oz

-20 to 55°C/-4 to 131°F
max. 95% non-condensing

-30 to 70°C/-22 to 158°F
bus powered, 11-14V

<180mW (idle mode)

IP20
CE
MasterBus,
CZone (upcoming)

WARNING

If you are not knowledgeable about electrical
systems, have an electrical professional install this
unit.

CAUTION

The SmartRemote is not waterproof. Do not install
where the display is exposed to water.

Warranty

The Mastervolt product warranty covers the
SmartRemote for the first two years after the
purchase date.
The warranty is limited to the cost of repair and/or
replacement of the product. Costs of labor or
shipping are not covered by this warranty.
Mastervolt cannot accept liability for damage due to
the misuse of the SmartRemote.

Correct Disposal

Contact your local waste disposal depart­ment to properly dispose of the unit.

EMEA
Snijdersbergweg 93
1105 AN AMSTERDAM
The Netherlands
[phone]
[e-mail]

NORTH AMERICA
N86 W12500 Westbrook Crossing
Menomonee Falls, WISCONSIN 53051
USA
[phone], Option 1
[e-mail]

ASIA/PACIFIC
42 Apollo Drive, Rosedale
AUCKLAND 0632
New Zealand
+ 64 9 415 7261
[e-mail]

SmartRemote

QuickStart Installation Guide

Components included

Head unit Surface

mount bezel

4 × Phillips
countersunk
self-tapping

Bayonet collar

Mastervolt CZone Drop Cable*
(1m / 3.3ft)

MasterBus cable*
(6m / 20ft)

* Need to be ordered separately with OEM packaging

To download this guide in other languages,
please visit our website: www.mastervolt.com

screws (2.9×16)

MasterBus Terminator*

Operation Notes

The three push buttons P1, P2 and P3 provide a
scroll and select function. Their behavior depends
on the connected device.
When multiple devices are connected, first select
the required device.

P1 P2 P3

When idle, the button menu slides down. To get it
back, press any button.
To enter the main menu, simultaneously press P1
and P3 for 5 seconds.

The simple and intuitive screens speak for
themselves. For example when monitoring an
inverter or charger:
Press P1 to switch the inverter on or off.
Press P2 or P3 to adjust the power sharing level.

Installation Notes

• Before installing, be sure to turn electrical
power off.

• The SmartRemote is designed for indoor
use only.

• Make sure the front panel is easy
accessible and readable.

• Always check for existing wiring, pipes, etc.
before drilling or cutting into walls.

• Make sure there is adequate space behind
the mounting surface to fit the
SmartRemote, including its cables.

• The SmartRemote is powered by the
MasterBus network.

Surface Mount

Connect the required RJ45 cable at the back of
the SmartRemote.

SmartRemote
Back Side

CZone network wiring

Mounting Template

72mm [2.8"]

62mm [2.4"]

55mm [2.3"]

Ø 52mm [2"]

28mm [1.1"]

11mm [0.4"]

Mounting
Substrate

Network
Cables

Front Panel

Head
Unit

MasterBus network wiring

Ensure that the network is properly terminated.

360 Panel Mount

Note that this requires the 360 Panel Mounting Kit
PN 1525 (sold separately).

STEP 1

Snap header and footer into the mounting clips
on the panel frame. Snap the bezel mount into
place with the flat edge up.

STEP 2

Place the carrier mount behind the panel, aligning
mounting holes, and attach with 4 screws.

STEP 3

Place the SmartRemote and fasten with the
bayonet collar. Turn collar until is snaps.

Front
Panel

72mm [2.8"]

Bezel
Mount

Head
Unit

Header

Footer

Carrier MountPanel Frame

Bayonet
Collar

Network
Cables