Page 1
OPERATING MANUAL
12.5A Angle Grinder
241-0781
IMPORTANT :
Carefully read this Owner’s Manual before using this tool. Pay close attention to all Safety Instructions, Warnings, and Caution sections. Use this tool
properly, and only for its intended use.
Safety symbols in this manual are used to flag possible dangers. The safety
symbols and their explanations require the operator’s full understanding. The
safety warnings do not, by themselves, eliminate any danger, and they are not
a substitute for proper accident prevention measures.
This Safety Alert Symbol indicates caution, warning, or danger. Failure to
obey a safety warning can result in serious injury to yourself or others. To reduce
the risk of injury, fire, or electric shock, always follow the safety precautions.
Page 2
2
3
TABLE OF CONTENTS
120V ~ 60Hz
Specifications .................................................................................................Page 2
Rules for Safe Operation ..............................................................................Page 3
Description ......................................................................................................Page 8
Assembly & Adjustments..............................................................................Page 9
Operation .........................................................................................................Page 11
Accessories .................................................................................................... Page 12
Maintenance...................................................................................................Page 12
Warranty .......................................................................................................... Page 13
SPECIFICATIONS
Rating 120 V 60Hz
Motor 12.5 A
No load Speed 6000 RPM
Wheel diameter 7”
Arbor size 5/8”-11 UNC
Cord length 8’
Weight: 10 lb 6 oz
SAFETY SYMBOLS FOR YOUR TOOL
The label on your tool may include the following symbols.
V...............................................................Volts
A...............................................................Amps
Hz.............................................................Hertz
W..............................................................Watts
min...........................................................Minutes
...........................................................Alternating Current
............................................................Direct Current
n
...........................................................No-load Speed
o
............................................................Class II construction
.../min.......................................................Revolutions or Strokes per minute
.................................................... Indicates danger, warning caution. It means
attention! Your safety is involved.
RULES FOR SAFE OPERATION
KNOW THE TOOL
Read this operating manual and all the labels affixed to the angle grinder
carefully before using this tool. Keep this manual available for future
reference.
IMPORTANT
This tool should only be serviced by a qualified service technician.
READ ALL INSTRUCTIONS THOROUGHLY
GENERAL SAFETY RULES FOR ALL POWER TOOLS
WARNING!Read and understand all instructions. Failure to follow all in-
structions listed below may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Work Area
Keep your work area clean and well lit. Cluttered benches and dark
areas invite accidents.
Do not operate power tools in explosive envirnments, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep bystanders, children, and visitors away while operating a power
tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
Double insulated tools are equipped with a polarized plug (one blade
is wider than the other.) This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician
to install a polarized outlet. Do not change the
plug in any way. Double insulation eliminates
the need for the three wire grounded power cord
and grounded power supply system.
Avoid body contact with grounded surfaces such
as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your
body is grounded.
Page 3
4
5
Don’t expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
footing and balance enables better control of the tool in unexpected
situations.
Do not abuse the cord. Never use the cord to carry the tools or pull
the plug from an outlet. Keep cord away from heat, oil, sharp edges or
moving parts. Replace damaged cords immediately. Damaged cords
increase the risk of electric shock.
When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These cords are rated for outdoor use and reduce
the risk of electric shock. The following table shows the correct size to
use, depending on cord length and nameplate amperage rating of the tool.
When in doubt, use the next heavier gauge. Always use UL and CSA listed
extension cords.
Recommended sizes of extension cords
Total length of cord in feet
Tool’s Ampere rating Volts
0-6
6-10 18 16 14 12
10-12 16 16 14 12
12-16 14 12 Not Recommended
PERSONAL SAFETY
Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use tool while tired or under the influence
of drugs, alcohol, or medication. A moment of inattention while operating
power tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure switch is off before plugging in.
Carrying tools with your finger on the switch or plugging in tools that have
the switch on invites accidents.
Remove adjusting keys or wrenches before turning the tool on. A wrench
or a key that is left attached to a rotating part of the tool may result in
personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper
120
V~
Cord size in A. W. G.(minimum)
25’ 50’ 100’ 150’
18 16 16 14
Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
Before connecting the tool to a power source (receptacle, outlet, etc.), be
sure voltage supplied is the same as that specified on the nameplate of
the tool. A power source with voltage greater than that specified for the
tool can result in serious injury to the user – as well as damage to the tool.
Tool Use and Care
Use clamps or other practical way to secure and support the workpiece
to a stable platform. Holding the work by hand or against your body is
unstable and may lead to loss of control.
Do not force tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which is designed.
Do not use tool if switch does not turn it on or off. Any tool that cannot be
controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
Store idle tools out of reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools, with sharp cutting edges are less likely to bind and are
easier to control.
Check for misalignment or binding of moving parts, breakage of parts,
and any other condition that may affect the tools operation. If damaged,
have the tool serviced before using. Many accidents are caused by poorly
maintained tools.
Use only accessories that are recommended by the manufacturer for
your model. Accessories that may be suitable for one tool, may become
hazardous when used on another tool.
Do not alter or misuse tool. These tools are precision built. Any alteration
or modification not specified is misuse and may result in a dangerous
condition.
Page 4
6
7
SERVICE
Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could result
in a risk of injury.
Do not use a grinding wheel that is larger than the maximum
recommended size for your tool or worn down damaged wheels from
larger grinders. Wheels intended for large angle sander/grinders are not
suitable for the high speed of a small angle sander/grinder; these wheels
may easily burst and the fragments strike you or bystanders.
When servicing a tool, use only identical replacement parts. Follow
instructions in the Maintenance section of this manual. Use of
unauthorized parts or failure to follow Maintenance Instructions may
create a risk of electric shock or injury.
SPECIFIC SAFETY RULES FOR ANGLE GRINDER
Always use the proper guard with the grinding wheel. A guard
protects operator from broken wheel fragments. When using grinding
wheel attachments, the guard must always be attached to the tool and
positioned for maximum safety, so the least amount of wheel is exposed
from the side from which the tool is being operated.
Accessories must be rated for at least the speed recommended on the
tool warning label. Wheels and other accessories running over the
rated speed can fly apart and cause injury. Grinding wheels or any other
accessory must have a maximum safe operating speed greater than the
“no load RPM” marked on the tool’s nameplate.
Hold the tool by its insulated gripping surfaces when performing an
operation where the cutting tool may contact hidden wiring or its own
cord. Contact with a “live” wire will make exposed metal parts of the tool
“live” and shock the operator.
Always use the auxiliary handle for maximum control over torque
reaction or kick-back. Operation of the grinder without the side handle
could cause loss of control of the grinder, resulting in possible serious
personal injury.
Before using a grinder or installing a new wheel, inspect the grinding
wheel for chips and cracks. Remove bad wheels immediately. Run the
tool at no load for one minute, holding the tool in the direction away from
people. Wheels with flaws will normally break apart during this time.
Carefully handle both the tool and individual grinding wheels to avoid
chipping or cracking. Install a new wheel if the tool is dropped while
grinding. Do not use a wheel that may be damaged. Fragments from a
wheel that bursts during operation will fly away at great velocity, possibly
striking you or bystanders.
Do not use depressed hub grinding wheels for cut-off operations.
Depressed hub wheels or type 27 wheels are not intended for side loading
and may shatter under overload.
Do not use this tool with a “Woodcarving” blade. Such blades create
frequent kick-back and loss of control.
Wear proper apparel while using a sander/grinder. Wear a face shield
(or at least safety goggles), dust mask, leather gloves and shop apron
capable of stopping small wheel or workpiece fragments.
Position the cord clear of the spinning grinding wheel or any other
sanding accessory. Do not wrap the cord around your arm or wrist. If you
lose control and have the cord wrapped around your arm or wrist it may
entrap you and cause injury.
Avoid bouncing and snagging the wheel, especially when working
corners, sharp edges, etc. This can cause loss of control and kick-back.
Regularly clean the tool’s air vents by compressed air. Excessive
accumulation of powdered metal inside the motor housing may cause
electrical failures.
Do not grind or sand near flammable materials. Sparks from the wheel
could ignite these materials.
This tool can be converted to a sander. When grinding is resumed the
proper guard and wheel flanges must be reinstalled before proceeding
with grinding. The guard must always be attached to the tool and
positioned for maximum safety, so the least amount of wheel is exposed
from the side the tool is being operated. The grinding wheel guard cannot
be used for most sanding operations or for wire brushing.
When sanding, do not use an oversized sanding disc. A larger sanding
disc will extend beyond the sanding pad,causing snagging, tearing of the
disc or kick-back. Extra paper extending beyond the sanding pad can also
cause serious lacerations.
When sanding chemically pressure-treated lumber, paint that may be
lead based, or any other materials that may contain carcinogens, use
Page 5
8
9
special precautions. A suitable breathing respirator must be worn by all
persons entering the work area. the work area should be sealed by plastic
sheeting and persons not protected should be kept out until the work area
is thoroughly cleaned.
Direct the discharge of the spinning wire brush away from you. Small
particles and tiny wire fragments may be discharged at high velocity
during the “cleaning” action with these brushes and may become
imbedded in your skin.
WARNING! Some dust created by power sanding, sawing, grinding, drill-
ing, and other construction activities contains chemicals known to cause
cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.
Fig. 1
3
4
1. Trigger switch
2. Lock-off button
3. Spindle lock button
4. Grinding wheel
5. Backing flange
6. Wheel guard
7. Side handle
8. Lock nut
2
1
7
6
5 8
DESCRIPTION
KNOW THE ANGLE GRINDER (Fig. 1)
The machine is intended for grinding metal and stone materials without using
water.
Before attempting to use this angle grinder, become familiar with all its
operating features and safety requirements.
WARNING! Do not allow familiarity with the angle grinder to cause carelessness. Remember that a careless fraction of a second is sufficient enough
to inflict severe injury.
WARNING! Remove the angle grinder from the carton and examine it
carefully. Do not leave carton or any packaging material until all parts are
examined.
ASSEMBLY AND ADJUSTMENT
WHEEL GUARD INSTALLATION
WARNING! To avoid injury, ALWAYS turn the tool off and the wheel grinder
and disconnect from the power outlet before installing or changing the grinding wheel.
WARNING! Always use wheel
guard with disc grinding wheels.
Always close the latch to secure
the guard. Keep the guard between you and the wheel. Do not
direct guard opening toward your
body.
The position of the guard can be
adjusted to accommodate the
operation being performed.
Fig. 2
Notch
Bump
Release/lock latch
Page 6
10
11
LOCK NUT
GRINDING
WHEEL
BACKING
FLANGE
SPINDLE
To attach the wheel guard, DISCONNECT the tool from the power source.
Open guard-release/lock latch and position the guard on the spindle neck so
that the bump guard lines up with the notch on the spindle neck.(Fig.2)
Rotate the guard to the desired position, and close the latch to secure the
guard in place.
OPERATION
SWITCH ON AND OFF (Fig.5)
1. To turn the angle grinder “ON”,
push in the lock-off button (2)
and press the trigger switch (1).
Fig. 5
NOTE: If the lock latch does not securely clamp the guard to the spindle
neck, open the latch and tighten the adjustment screw to increase the
clamping tension.
To remove guard: Open the guard-release/lock latch, rotate the guard until
the bump on the guard lines up with the notches on the spindle neck, and lift
the guard off the spindle neck.
LOCK NUT AND BACKING FLANGE
Fig.3
Your tool is equipped with a
threaded spindle for mounting
accessories. Always use the
supplied lock nut (and backing
flange), which has the same
thread size as the spindle.
SIDE HANDLE (Fig.3)
The side handle used to guide and
balance the tool can be threaded into the front housing on left, right and the
top side of tool. The tool, depending on personal preference and comfort.
Use the side handle for safe control and ease of operation.
DISC GRINDING WHEEL
Fig. 4
ASSEMBLY (Fig.4)
2. To turn the tool “OFF,” release
the trigger switch.
WARNING! Hold the tool with
both hands while starting the tool, since torque from the motor can cause the
tool to twist. Start the tool before applying it to the workpiece and allow the tool
to come to full speed before contacting the tool to the workpiece. Lift the tool
from the workpiece before releasing the switch. Do not turn the switch “ON”
and “OFF” while the tool is under load, this will greatly decrease the tool life and
cause severe injury.
SELECTING GRINDING WHEELS
WARNING! Before using a grinding wheel, be certain that its maximum
safe operating speed is not exceeded by the nameplate speed of the grinder.
Do not exceed the recommended wheel diameter.
DISC GRINDING WHEELS
Grinding wheels should be carefully selected in order to use the grinder most
efficiently. Wheels vary in type of abrasive, bond, hardness, grit size and
structure. The correct type of wheel to use is determined by the job. Use disc
grinding wheels for fast grinding of structural steel, heavy weld beads, steel
casting, stainless steel and other ferrous metals.
GRINDING TIPS (Fig.6)
Disconnect the tool from the
power source. Be sure that
the wheel guard is in place for
grinding. Place the backing flange
and grinding wheel on the spindle.
Thread on the lock nut and tighten
the nut using the supplied lock-nut wrench, while holding the spindle lock in.
To remove: Reverse procedure.
Efficient grinding is achieved
by controlling the pressure and
keeping the angle between wheel
and workpiece at 10
°
to 15°. If the
wheel is flat, the tool is difficult to
control. If the angle is too steep,
the pressure is concentrated on a
small area causing burning to the
work surface.
Fig. 6
100 to 15
0
Page 7
12
13
WARNING! Excessive or sudden pressure on the wheel will slow grinding
action and put dangerous stresses on the wheel.
When grinding with a new wheel, be certain to grind while pulling tool
backwards until wheel becomes rounded on its edge. New wheels have
sharp corners which tend to “bite” or cut into workpiece when pushing
forward.
ACCESSORIES
Spanner 1pc
Side handle 1pc
Safety guard 1pc
Metal grinding disc 1pc
Stone grinding disc 1pc
MAINTENANCE
Before each use, inspect the grinder, switch and cord for damage. Check
for damaged, missing, or worn parts. Check for loose screws, misalignment
or binding of moving parts, or any other conditions that may affect the
operation. If abnormal vibration or noise occurs, turn the tool off immediately
and have the problem corrected before further use.
WARRANTY
If, during normal use, this MASTERFORCE™ power tool breaks or fails due
to a defect in material or workmanship within three years from the date of
original purchase, simply bring this tool and its sales receipt back to your
nearest Menards
three years.
The warranty:
(1) excludes expendable parts including but not limited to blades, bits, light
bulbs, and/or batteries;
(2) shall be void if this tool is used for commercial or/and rental purposes;
and
(3) does not cover any losses, injuries to persons/properties, or costs. This
warranty does give you specific legal rights and you may have other
rights, which vary from state to state.
®
retail store for a free equivalent replacement within those
Before cleaning or performing any maintenance, the tool should be
unplugged from the power supply. Using compressed air may be the most
effective cleaning method. Always wear safety goggles when cleaning tools
with compressed air.
The brushes and commutator in your tool have been engineered for many
hours of dependable service. To maintain peak efficiency of the motor, we
recommend the brushes be examined every two to six months.
WARNING! Do not let brake fluids, gasoline, petroleum-based products,
penetrating oil, etc., come in contact with plastic parts. They contain chemicals that can damage, weaken or destroy plastic.
WARNING! When servicing use only identical replacement parts. Use of
any other parts may create a hazard or cause product damage.
WARNING! Check extension cords before each use. If damaged replace
immediately. Never use tool with a damaged cord.
WARNING! To ensure safety and reliability, all repairs should be performed
by a qualified service technician.
Page 8
14
Loading...