Page 1
241-0465
BRUSHLESS 1/2”
HAMMER DRILL
For questions / comments, technical assistance or repair parts –
Please Call Toll Free: 1-866-917-4374. (M-F 8:30am-5:00pm Est.)
OPERATOR’S MANUAL
CAUTION:
To Reduce The Risk Of Injury, User Must Read And
Understand Operator’s Manual. Save These Instructions For Future
Reference.
Page 2
TABLE OF CONTENTS
Safety Symbols ......................................................... Page 2
Safety Instructions ...................................................... Page 3
Overview/Specications .................................................Page 7
Assembly .............................................................Page 8
Operation ............................................................ Page 12
Maintenance .......................................................... Page 15
Troubleshooting .......................................................Page 16
Warranty .............................................................Page 18
Page 3
Page 2
SAFETY SYMBOLS
Some of these following symbols may be used on this tool. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the tool better and
more safely.
WARNING:
To ensure safety and reliability, all repairs should be performed by a
qualied service technician.
Symbol
Name
Designation / Explanation
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watts Power
∿
Alternating current Type of current
�
Direct current Type or characteristic of current
n
o
No-load speed Rotational speed at no load
lbs Pounds Weight
Class II construction Double insulated construction
.../min
Per minute
Revolutions, strokes, surface speed
orbits, etc., per minute
Wear safety goggles
WARNING:
The operation of any
power tool can result in foreign objects
being thrown into your eyes, which can
result in severe eye damage. Before
beginning power tool operation, always
wear safety goggles or safety glasses
with side shields and a full-face shield
when needed. We recommend a Wide
Vision Safety Mask for use over eyeglasses or standard safety glasses with
side shields. Always use eye protection
which is marked to comply with
ANSI Z87.1.
Page 4
Page 3
The purpose of safety symbols is to attract your attention to possible dangers. The
safety symbols and the explanations with them deserve your careful attention and
understanding. The symbol warnings do not, by themselves, eliminate any danger. The
instructions and warnings they give are not substitutes for proper accident prevention
measures.
WARNING:
Be sure to read and understand all safety instructions in this manual,
including all safety alert symbols such as “DANGER,” “WARNING,” and “CAUTION”
before using this tool. Failure to follow all instructions listed below may result in electric
shock, re, and/or serious personal injury.
SYMBOL MEANING
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, OR CAUTION.
May be used in conjunction with other symbols or pictographs.
DANGER:
Indicates an imminently hazardous situation, which, if not avoided,
will result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided,
could result in minor or moderate injury.
NOTICE:
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SAVE THESE INSTRUCTIONS!
SAFETY INSTRUCTIONS
Page 5
Page 4
GENERAL POWER TOOL SAFETY
WARNINGS
WARNING:
Read all safety
warnings and all instructions. Failure to
follow the warnings and instructions may
result in electric shock, re and/or serious
injury.
Save all warnings and instructions for
future reference.
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
WORK AREA SAFETY
1. Keep work area clean and well
lit. Cluttered and dark areas invite
accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence
of ammable liquids, gases or dust.
Power tools create sparks which may
ignite the dust or fumes.
3. Keep children and bystanders away
while operating a power tool. Distractions
can cause you to lose control
ELECTRICAL SAFETY
1. Power tool plugs must match the
outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.
Unmodied plugs and matching outlets
will reduce risk of electric shock.
2. Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric
shock if your body is earthed or
grounded.
3. Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric
shock.
4. Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase
the risk of electric shock.
5. When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric
shock.
6. If operating a power tool in a damp
location is unavoidable, use a groundfault circuit interrupter (GFCI) protected
supply. Use of a GFCI reduces the risk
of electric shock.
PERSONAL SAFETY
1. Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired or
under the inuence of drugs, alcohol
or medication. A moment of inattention
while operating power tools may result
in serious personal injury.
2. Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, nonskid safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal injuries.
3. Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or
battery pack, picking up or carrying
the tool. Carrying power tools with your
nger on the switch or energising power
tools that have the switch on invites
accidents.
4. Remove any adjusting key or wrench
before turning the power tool on.
A wrench or a key left attached to a
rotating part of the power tool may
result in personal injury.
5. Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in
unexpected situations.
6. Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
7. If devices are provided for the
connection of dust extraction and
collection facilities, ensure that these
are connected and properly used.
Use of these devices can reduce dustrelated hazards.
SAFETY INSTRUCTIONS
Page 6
Page 5
SAFETY INSTRUCTIONS
POWER TOOL USE AND CARE
1. Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and more safely at the rate for
which it was designed.
2. Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with
the switch is dangerous and must be
repaired.
3. Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories,
or storing power tools. Such preventive
safety measures reduce the risk of
starting the power tool accidentally.
4. Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands
of untrained users.
5. Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power
tool’s operation. If damaged, have
the power tool repaired before use.
Many accidents are caused by poorly
maintained power tools.
6. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
7. Use the power tool, accessories, tool
bits, etc. in accordance with these
instructions, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
BATTERY TOOL USE AND CARE
1. Recharge only with the charger
specied by the manufacturer. A
charger that is suitable for one type of
battery pack may create a risk of re
when used with another battery pack.
2. Use power tools only with specically
designated battery packs. Use of any
other battery packs may create a risk of
injury and re.
3. When battery pack is not in use, keep
it away from other metal objects, like
paper clips, coins, keys, nails, screws
or other small metal objects, that can
make a connection from one terminal
to another. Shorting the battery
terminals together may cause burns or
a re.
4. Under abusive conditions, liquid may
be ejected from the battery; avoid
contact. If contact accidentally occurs,
ush with water. if liquid contact eyes,
additionally seek medical help. Liquid
ejected from the battery may cause
irritation or burns.
SERVICE
1. Have your power tool serviced by
a qualied repair person using only
identical replacement parts. This will
ensure that the safety of the power tool
is maintained.
SPECIFIC SAFETY RULES FOR
HAMMER DRILLS
1. Use only with battery and charger listed
below.
Battery pack Charger
252-8024
252-8028
252-8029
252-8030
252-8031
252-8032
252-8033
252-8034
252-8035
252-8025
252-8036
252-8037
252-8044
2. Wear ear protectors when impact
drilling. Exposure to noise can cause
hearing loss.
3. Use auxiliary handle(s), if supplied
with the tool. Loss of control can
cause personal injury.
Page 7
Page 6
SAFETY INSTRUCTIONS
4. Hold power tool by insulated gripping
surfaces, when performing an
operation where the cutting accessory
may contact hidden wiring. Cutting
accessory contacting a “live” wire may
make exposed metal parts of the power
tool “live” and could give the operator
an electric shock.
5. Use clamps or another practical way to
secure and support the workpiece to
a stable platform. Holding the work by
your hand or against the body leaves it
unstable and may lead to loss of control.
6. Do not drill, fasten or break into
existing walls or other blind areas
where electrical wiring may exist. If
this situation is unavoidable, disconnect
all fuses or circuit breakers feeding this
worksite.
7. Always wear safety goggles or eye
protection when using this tool.
8. Use thick cushioned gloves and limit
the exposure time by taking frequent
rest periods. Vibration caused by
hammer-drill action may be harmful to
your hands and arms.
9. Secure the material being fastened.
Never hold it in your hand or across
your legs. Unstable support can cause
loss of control and injury.
10. Avoid accidental starting. Be sure the
forward/reverse switch is in the off
position before inserting battery pack.
Carrying appliances with your nger on
the switch or inserting the battery pack
into an appliance with the switch on
invites accidents.
11. Remove battery pack before changing
accessories. Accidental starting may
occur because battery appliances with
a battery inserted are in the operative
condition.
12. Do not use dull or damaged bits
and accessories. When installing an
accessory, insert the shank of the bit
well within the chuck. Be sure the chuck
has locked onto the bit correctly.
WARNING:
Some dust created by
power sanding, sawing, grinding, drilling
and other construction activities contains
chemicals known to the state of California
to cause cancer, birth defects or other
reproductive harm. Some examples of
these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and
cement and other masonry products,
and
• Arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to these
chemical: work in a well ventilated area,
and work with approved safety equipment,
such as those dust masks that are specially
designed to lter out microscopic particles.
Page 8
Page 7
OVERVIEW
Side Handle
Torque-Adjustment
Ring Clutch
Chuck Sleeve
Variable-Speed
Trigger Switch
Bit Holder
LED Worklight
Belt Clip
Mode-Selector Ring
Two-Speed Gearbox Switch
Direction-of-Rotation
Selector (Forward/
Center-Lock/Reverse)
SPECIFICATIONS
No-load Speed 0-500/ 0-1,850 RPM
Impact Rate 0-6,500/ 0-24,050 BPM
Torque 700 in.lb.
Chuck Size 1/2 in. (13mm)
Tool Weight (without battery) 3 lb. (1.36kg)
Page 9
Page 8
ASSEMBLY
WARNING:
If any part is broken
or missing, DO NOT attempt to plug in the
power cord or operate the tool until the
broken or missing part is replaced. Failure
to do so could result in possible serious
injury.
WARNING:
Do not attempt to
modify this tool or create accessories not
recommended for use with this tool. Any
such alteration or modication is misuse
and could result in a hazardous condition
leading to possible serious injury.
WARNING:
Your tool should
never be connected to the power source
when you are assembling parts, making
adjustments, installing or removing
blades, cleaning, or when it is not in
use. Disconnecting the tool will prevent
accidental starting, which could cause
serious personal injury.
CONTENTS
Brushless hammer drill, belt clip, bit holder,
bit, side handle and instruction manual.
UNPACKING
1. Carefully remove the tool and any
accessories from the carton. Make sure
that all items listed in the packing list are
included.
2. Inspect the tool carefully to make sure
that no breakage or damage occurred
during shipping.
3. Do not discard the packing material
until you have carefully inspected and
satisfactorily operated the tool.
Page 10
Page 9
ASSEMBLY
TO ATTACH BATTERY PACK
(FIG. 1)
1. Lock the trigger switch on the hammer
drill by placing the direction-of-rotation
selector in the center position.
2. Align the ribs on the battery pack with
the grooves of the hammer drill, and
then attach the battery pack.
NOTICE: Make sure that the latch on the
battery pack snaps into place and the
battery pack is secured to the hammer
drill before operation.
FIG. 1
Battery-release button
Detach
Attach
TO DETACH BATTERY PACK (FIG. 1)
1. Lock the trigger switch on the hammer
drill by placing the direction-of-rotation
selector in the center position.
2. Depress the battery-release button
located on the battery pack to release
the battery pack.
3. Pull the battery pack out and remove it
from the tool.
INSTALLING BITS (FIG. 2)
WARNING:
Disconnect the
battery pack from tool before making
any assembly, adjustments or changing
accessories. Such preventive safety
measures reduce the risk of starting the
tool accidentally.
1. Lock the trigger switch on the hammer
drill by placing the direction-of-rotation
selector in the center position.
2. Rotate the chuck sleeve
counterclockwise when viewed from
chuck end, and open the chuck to the
approximate drill-bit diameter.
3. Insert a bit up to the drill bit utes for
small bits, or as far as it will go for large
bits.
4. Close the chuck by rotating the chuck
sleeve clockwise when viewed from
chuck end and securely tighten it by
hand.
WARNING:
Do not use the power
of the hammer drill while grasping chuck
to loosen or tighten the chuck on the bit.
A friction burn or hand injury is possible if
attempting to grasp the spinning chuck.
FIG. 2
Release
Grip
REMOVING BITS (FIG. 2)
1. Lock the trigger switch by placing the
direction-of-rotation selector in the
center position.
2. Rotate the chuck sleeve
counterclockwise when viewed from the
chuck end.
3. Remove the bit.
WARNING:
Use protective gloves
when removing the bit from the tool, or
rst allow the bit to cool down. The bit
may be hot after prolonged use.
Page 11
Page 10
ASSEMBLY
INSTALLING AND REMOVING
THE BELT CLIP (FIG. 3)
To install the belt clip:
1. Remove the battery from the tool.
2. Align the rib of the clip with the hole on
the base of the hammer drill.
3. Insert the screw (included) and tighten
the screw securely with a screwdriver
(not included). The belt clip can be
positioned on either side of the tool.
To remove the belt clip:
1. Remove the battery from the tool.
2. Use a screwdriver to loosen the screw
that attaches the belt clip to the hammer
drill.
3. Remove the screw and the belt clip.
FIG. 3
Belt clip
Screw
INSTALLING AND REMOVING
THE BIT HOLDER (FIG. 4)
To install the bit holder:
1. Remove the battery from the tool.
2. Align the rib of the bit holder with the
hole in the base of the hammer drill.
3. Insert the screw (included) and tighten
the screw securely with a screwdriver
(not included). The bit holder can be
positioned on either side of the tool.
To remove the bit holder:
1. Remove the battery from the tool.
2. Use a screwdriver to loosen the screw
that attaches the bit holder to the
hammer drill.
3. Remove the screw and the bit holder.
FIG. 4
Bit holder
Screw
INSTALLING AND REMOVING
THE SIDE HANDLE (FIG. 5)
WARNING:
To reduce the risk
of injury, always use a side handle when
using this tool. Always hold it securely.
Ensure that side handle is tightened
securely before each use.
To install the side handle:
1. Remove the battery from the tool.
2. Loosen the side handle grip until the
hooks are far enough apart to t into the
slots on the gear-case ring.
3. Position the side handle on the left or
the right side of the tool.
4. Slide the hooks into the slots as far as
the hooks will go.
5. Tighten the side handle grip until it is
secure.
To remove the side handle:
1. Remove the battery from the tool.
2. Loosen the side handle grip until the
side handle can be removed.
FIG. 5
Slot
Hook
Loosen
Tighten
Page 12
Page 11
OPERATION
VARIABLE-SPEED TRIGGER
SWITCH (FIG. 6)
1. To turn the hammer drill ON, press the
trigger switch.
2. To turn the hammer drill OFF, release the
trigger switch.
3. The variable-speed trigger switch
delivers higher speed with increased
trigger pressure and lower speed with
decreased trigger pressure.
FIG. 6
Trigger switch
Direction-
of-Rotation
Selector
ELECTRIC BRAKE
When the trigger switch is released, it
activates the brake to stop the chuck
quickly. This is especially useful in the
repetitive driving and removal of screws.
DIRECTION-OF-ROTATION
SELECTOR (FIG. 7)
The direction of bit rotation is reversible and
is controlled by a selector located above the
trigger switch. With the hammer drill held in
the normal operating position:
1. Position the direction-of-rotation
selector to the left of the tool for forward
rotation.
2. Position the direction-of-rotation
selector to the right of the tool for
reverse rotation.
3. Setting the direction-of-rotation selector
in the OFF (center-lock) position helps
reduce the possibility of accidental
starting when not in use.
NOTICE: To prevent gear damage,
always allow the hammer drill to come
to a complete stop before changing the
direction of rotation.
FIG. 7
Forward
Reverse
Page 13
Page 12
OPERATION
TWO-SPEED GEARBOX SWITCH
(FIG. 8)
Your tool is equipped with two separate
speed ranges: speed 1 (low speed) and
speed 2 (high speed). Speed 1 provides
high-torque and slower drilling speeds
for heavy duty-work or for driving screws.
Speed 2 provides faster speeds for drilling
and lighter work. To change speeds, slide
gearbox switch, to the high or low position.
NOTICE: Do not change speeds when the
tool is running. Always allow the drill to
come to a complete stop before changing
speeds.
NOTICE: Avoid running the hammer drill
at low speed for extended periods of time.
Running at low speed under constant use
may cause the drill to become overheated.
If this occurs, cool the drill by running it
without a load at high speed.
5 7 9 11 13
FIG. 8
Two-speed gearbox switch
MODE SELECTION (FIG. 9)
Your tool has three operating modes: drilling
with hammering action, drilling only, and
driving screws. -To set the operating mode,
rotate the mode-selector ring and torqueadjustment ring to the desired settings.
To use the hammer-drilling mode:
1. Rotate the mode-selector ring until the
hammer symbol
appears in line with
the arrow.
2. Apply pressure to the bit during
operation to engage the hammering
mechanism.
NOTE: The number selected on the
torque-adjustment ring has no effect on
operation of the drill in hammer mode.
To use the drilling only mode:
Rotate the mode-selector ring until the drill
symbol appears in line with the arrow.
NOTE: The number selected on the
torque-adjustment ring has no effect on
the operation of the drill in the drilling
mode.
To use the driving screws mode:
1. Rotate the mode selector ring until the
drive symbol appears in line with the
arrow.
2. Then rotate the torque-adjustment ring
until the desired clutch setting appears
in line with the arrow. The torqueadjustment ring, when properly adjusted,
will slip at a preset torque to prevent
driving the screw too deeply into different
materials and to prevent damage to the
screw or tool.
5 7 9 11 13
FIG. 9
Mode selector ring
Torque-adjustment ring
Page 14
Page 13
OPERATION
LED WORKLIGHT (FIG. 11)
Your tool is equipped with a light that
turns on automatically when the switch is
activated to provide better visibility when
drilling/driving.
FIG. 11
LED worklight
DRILLING (FIG. 12)
WARNING:
To reduce the risk of
injury, always use the side handle when
using this tool. Always hold it securely.
Ensure that the side handle is tightened
securely before each use.
1. Check that the direction-of-rotation
selector for the correct setting.
2. Secure the material to be drilled in a vise
or with clamps to keep it from turning as
the drill bit rotates.
3. Hold the drill rmly and place the bit at
the point to be drilled.
4. Depress the trigger switch to start the
drill.
5. Move the drill bit into the workpiece,
applying only enough pressure to keep
the bit cutting. Do not force the drill or
apply side pressure to elongate a hole.
Let the tool do the work.
6. When drilling hard, smooth surfaces,
use a center punch to mark the desired
location of the hole. This will prevent the
drill bit from slipping off center as the
hole is started.
7. When drilling metals, use light oil on
the drill bit to keep it from overheating.
The oil will prolong the life of the bit and
increase the drilling action.
ADJUSTABLE CLUTCH (FIG. 10)
Your tool features 24 clutch settings. Output torque will increase as the torque-adjustment ring is rotated from 1 to 24. When
using the hammer drill for different driving
applications, it is necessary to increase or
decrease the torque in order to help prevent
the possibility of damaging screw heads,
threads, workpiece, etc.
The proper setting depends on the job and
the type of bit, fastener, and material you will
be using. In general, use greater torque for
larger screws, but if the torque is too high,
the screws may be damaged or broken.
For delicate operations, such as removing
a partially stripped screw, use a low torque
setting. For operations such as drilling into
hardwood, use a higher torque setting.
5 7 9 11 13
FIG. 10
To increase torque
To decrease torque
Page 15
Page 14
OPERATION
8. If the bit jams in the workpiece or if the
drill stalls, stop the tool immediately.
Remove the bit from the workpiece and
determine the reason for jamming.
FIG. 12
WOOD DRILLING
For maximum performance, use high-speed
steel or brad point bits for wood drilling.
1. Begin drilling at a very low speed to
prevent the bit from slipping off the
starting point.
2. Increase speed as the drill bit bites into
the material.
3. When drilling “through” holes, place a
block of wood behind the workpiece to
prevent ragged or splintered edges on
the back side of the hole.
METAL DRILLING
For maximum performance, use high-speed
steel bits for metal or steel drilling.
1. When drilling metals, use a light oil on
the drill bit to keep it from overheating.
The oil will prolong the life of the bit and
increase the drilling action.
2. Begin drilling at a very low speed to
prevent the bit from slipping off of the
starting point.
3. Maintain a speed and pressure that
allows cutting without overheating the
bit. Applying too much pressure will:
- Overheat the hammer drill.
- Wear the bearings.
- Bend or burn bits.
- Produce off-center or irregular-shaped
holes.
MASONRY DRILLING
For maximum performance, use high-speed
steel bits for masonry drilling.
1. When drilling in masonry, select the
hammer drill operating mode.
2. Drilling soft masonry materials such
as cinder block requires little pressure.
Hard materials like concrete require
more pressure.
3. A smooth, even ow of dust indicates
the proper drilling rate. Do not let the bit
spin in the hole without cutting. Do not
use water to settle dust or to cool bit.
WARNING:
Always wear safety
goggles or safety glasses with side
shields during power tool operation or
when blowing dust. If operation is dusty,
also wear a dust mask.
Page 16
Page 15
MAINTENANCE
WARNING:
To avoid serious
personal injury, always remove the battery
pack from the tool when cleaning or
performing any maintenance.
WARNING:
When servicing, use
only identical replacement parts. Use of
any other parts may create a hazard or
cause product damage.
WARNING:
It is not recommended
to use compressed dry air as cleaning
method of the hammer drill. If cleaning
with compressed air is the only method
to apply, always wear safety goggles or
safety glasses with side shields when
using compressed air to clean the tool. If
the operation is dusty, also wear a dust
mask.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic
parts. Most plastics are susceptible to
damage from various types of commercial
solvents. Use clean cloth to remove dirt,
dust, oil, grease, etc.
WARNING:
Do not at any time
allow brake uids, gasoline, petroleumbased products, penetrating oils, etc.
to come in contact with plastic parts.
Chemicals can damage, weaken or
destroy plastic which may result in
serious personal injury.
WARNING:
When servicing, use
only identical replacement parts. Use
of any other parts may create a hazard
or cause product damage. To ensure
safety and reliability, all repairs should
be performed by a qualied service
technician.
CHUCK REMOVAL (FIG. 13)
The chuck can be removed and replaced
with a new one.
1. Lock the trigger switch by placing the
direction-of-rotation selector in the
center position.
2. Open the chuck jaws. Using a
screwdriver, remove the chuck screw by
turning it clockwise,
3. Insert a 5/16-in. or larger hex key into
the chuck of the hammer drill and
tighten the chuck jaws securely.
4. Tap the hex key sharply with a mallet in
a counterclockwise direction. This will
loosen the chuck for easy removal.
5. Attach a new chuck to the spindle and
tighten the chuck screw.
FIG. 13
Mallet
Chuck jaws
Hex wrench
Page 17
Page 16
TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
The hammer drill does not work. The battery is depleted. Charge the battery.
The bit cannot be installed. The sleeve is not released. Release the sleeve.
The bit does not t the
sleeve.
Use a suitable bit.
Page 18
Page 17
NOTES
Page 19
Page 18
SAVE YOUR RECEIPTS
THIS WARRANTY IS VOID WITHOUT THEM
BRUSHLESS 1/2” HAMMER DRILL
WARRANTY
90-DAY MONEY BACK GUARANTEE:
This MASTERFORCE® brand power tool carries our 90-DAY Money Back
Guarantee. If you are not completely satised with your MASTERFORCE® brand
power tool for any reason within ninety (90) days from the date of purchase, return
the tool with your original receipt to any MENARDS® retail store, and we will provide
you a refund – no questions asked.
3-YEAR LIMITED WARRANTY:
This MASTERFORCE® brand power tool carries our famous No Hassle 3-Year
Limited Warranty to the original purchaser. If, during normal use, this
MASTERFORCE® power tool breaks or fails due to a defect in material or
workmanship within three (3) years from the date of original purchase, simply bring
this tool with the original sales receipt back to your nearest MENARDS® retail store.
At its discretion, MASTERFORCE
®
agrees to have the tool or any defective part(s)
repaired or replaced with the same or similar MASTERFORCE
®
product or part
free of charge, within the stated warranty period, when returned by the original
purchaser with original sales receipt. Not withstanding the foregoing, this limited
warranty does not cover any damage that has resulted from abuse or misuse of the
Merchandise. This warranty: (1) excludes expendable parts including but not limited
to blades, brushes, belts, bits, light bulbs, and/or batteries; (2) shall be void if this
tool is used for commercial and/or rental purposes; and (3) does not cover any
losses, injuries to persons/property or costs. This warranty does give you specic
legal rights and you may have other rights, which vary from state to state. Be
careful, tools are dangerous if improperly used or maintained. Seller’s employees
are not qualied to advise you on the use of this Merchandise. Any oral
representation(s) made will not be binding on seller or its employees. The rights
under this limited warranty are to the original purchaser of the Merchandise and may
not be transferred to any subsequent owner. This limited warranty is in lieu of all
warranties, expressed or implied including warranties or merchantability and tness
for a particular purpose. Seller shall not be liable for any special, incidental, or
consequential damages. The sole exclusive remedy against the seller will be for the
replacement of any defects as provided herein, as long as the seller is willing or
able to replace this product or is willing to refund the purchase price as provided
above. For insurance purposes, seller is not allowed to demonstrate any of these
power tools for you.
For questions / comments, technical assistance or repair parts – Please Call Toll
Free at: 1-866-917-4374. (M-F 8:30am-5:00pm Est.)
Page 20
12/2016
© 2016 Menard, Inc., Eau Claire, WI 54703
Loading...