Page 1
Operator’s Manual
18.0-Volt Lithium-Ion Hammer Drill
Model No. 241-0412
IMPORTANT:
WARNING! To reduce the risk of injury, user must read instruction manual.
Safety symbols in this manual are used to flag possible dangers. The safety symbols and their explanations require your full understanding. The safety
warnings do not, by themselves, eliminate any danger, nor are they substitutes
for proper accident prevention measures.
This Safety Alert Symbol indicates caution, warning, or danger. Failure to
obey a safety warning can result in serious injury to yourself or others. To
reduce the risk of injury, fire, or electric shock, always follow the safety precautions.
CHARGE BATTERY
BEFORE FIRST USE
Page 2
2
3
TABLE OF CONTENTS
Safety Symbols .......................................................................................... page 3-4
Safety Instructions .................................................................................... page 5-9
Description ................................................................................................. page 10-12
Assembly ..................................................................................................... page 12
Operation .................................................................................................... page 13-23
Maintenance .............................................................................................. page 24-25
Troubleshooting ......................................................................................... page 26
Warranty ..................................................................................................... page 27
SAVE THESE INSTRUCTIONS!
This hammer drill has many features for making its use more pleasant and
enjoyable. Safety, performance, and dependability have been given top priority in
the design of this product making it easy to maintain and operate.
SAFETY SYMBOLS
The purpose of safety symbols is to attract your attention to possible
dangers.
The safety symbols and the explanations with them deserve your careful
attention and understanding. The symbol warnings do not by themselves
eliminate any danger. The instructions and warning they give are no
substitutes for proper accident prevention measures.
WARNING: Be sure to read and understand all safety instructions in this
manual, including all safety alert symbols such as “DANGER,” “WARNING”
and “CAUTION,” before using this drill. Failure to following all instructions
listed below may result in electric shock, fire and/or serious personal injury.
SYMBOL SIGNAL MEANING
DANGER:
Indicates an imminently hazardous situation,
which, if not avoided, will result in death or
serious injury.
WARNING:
Indicates a potentially hazardous situation, which,
if not avoided, could result in death or serious
injury.
CAUTION:
Indicates a potentially hazardous situation, which,
if not avoided, may result in minor or moderate
injury.
NOTE:
(Without Safety Alert Symbol) Indicates a situation
that may result in property damage.
WARNING: To ensure safety and reliability, all repairs should be performed
by a qualified service technician at Authorized Service Center.
WARNING: The operation of any power tool can result in
foreign objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool operation,
always wear safety goggles or safety glasses with side shields
and a full-face shield when needed. We recommend a Wide
Vision Safety Mask for use over eyeglasses or standard safety
glasses with side shields. Always use eye protection which is
marked to comply with ANSI Z87.1
Page 3
4
5
SAVE THESE INSTRUCTIONS
Some of these following symbols may be used on this tool. Please study them
and learn their meaning. Proper interpretation of these symbols will allow you to
operate the tool better and more safely.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
min Minutes Time
Alternating Current Type of current
Direct Current Type or a characteristic of current
n
o
No Load Speed Rotational speed, at no load
Class II
Construction
Double-insulated construction
.../min
Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
.../min
Wet Conditions
Alert
Do not expose to rain or use in damp locations.
.../min
Read The
Operator’s Manual
To reduce the risk of injury, user must read operator’s
manual.
.../min
Eye Protection
Always wear safety goggles or safety glasses with side
shields, or a full face shield when operating this product.
Safety Alert Precautions that involve your safety.
.../min
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
.../min
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
.../min
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
.../min
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
.../min
Hot Surface
To reduce the risk of injury or damage, avoid contact with
any hot surface.
SAFETY INSTRUCTIONS
WARNING: Read all safety warnings and instructions. Failure to follow
the warnings and instructions may result in electric shock, fire and / or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
The term power tool in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
WORK AREA SAFETY
Keep the work area clean and well lit. Cluttered or dark areas invite
accidents.
Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep the cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk of
electric shock.
When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
Page 4
6
7
PERSONAL SAFETY
Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use the tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection.
Protective equipment, such as dust mask, non-skid safety shoes, hard hat,
or hearing protection, used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and / or battery pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch or
energizing power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may
result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use
of these devices can reduce dust-related hazards.
4) POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and more safely
at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and
must be repaired.
Disconnect the plug from the power source and/or the battery pack from
the power tool before making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained
users.
Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc., in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
Recharge only with the charger specified by the manufacturer. A charger
that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.
Use power tools only with specifically designated battery packs. Use of
any other battery packs may create a risk of injury and fire.
When a battery pack is not in use, keep it away from other metal objects,
like paper clips, coins, keys, nails, screws or other small metal objects
that can make a connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burns.
6) SERVICE
Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
SPECIFIC SAFETY RULES FOR CORDLESS HAMMER DRILL
Use batteries only with charger listed.
Battery pack Charger
252-8024
252-8036
252-8028
252-8032
Hold power tools by their insulated gripping surfaces when performing
an operation where the cutting tool may contact hidden wiring or its own
cord. Contact with a “live” wire will also make exposed metal parts of the
tool “live” and shock the operator.
Page 5
8
9
Use protective gloves when removing the bit from the tool, or first allow
the clamp to cool down. The bit may be hot after prolonged use.
Use protective gloves when operating the tool. Protective gloves can help
to keep you from being burnt and hurt.
Keep your hands away from the motor-housing vents. Hot gas comes from
the vents during operation.
Do not operate the tool at full-load for long time, as this can cause the
motor to become too hot, which may damage the motor.
Release the trigger immediately when the screws are tightened to avoid
breaking the screw.
For best results, your battery tool should be charged in a location where
the temperature is more that 41°F(5°C) but less that 122°F (50°C). Do not
store outside or in vehicles.
SAFETY RULES FOR CHARGER
WARNING! Read and understand all instructions. Failure to follow all in-
structions listed below may result in electric shock, fire, and/or serious personal injury.
Before using the battery charger, read all instructions and cautionary
markings in this manual and on the battery charger, the battery, and the
product using the battery to prevent misuse of the products and possible
injury or damage.
CAUTION! To reduce the risk of electric shock or damage to the charger
and battery, charge only those rechargeable batteries specifically designated
on your charger’s label. Other types of batteries may burst, causing personal
injury or damage.
Do not use the charger outdoors or expose it to wet or damp conditions.
Water entering the charger will increase the risk of electric shock.
Use of an attachment not recommended or sold by the battery-charger
manufacturer may result in a risk of fire, electric shock or injury to
persons.
Do not abuse the cord or charger. Never use the cord to carry the charger.
Do not pull the charger cord to disconnect the plug from receptacle.
Damage to the cord or charger could occur and create an electric shock
hazard. Replace damaged cords immediately.
Make sure that the cord is located so that it will not be stepped on,
tripped over, come in contact with sharp edges or moving parts, or
otherwise subjected to damage or stress. This will reduce the risk of
accidental falls, which could cause injury and damage to the cord, which
could then result in electric shock.
Keep the cord and charger from heat to prevent damage to the housing or
internal parts.
Do not allow gasoline, oils, petroleum-based products, etc. to come in
contact with plastic parts. These materials contain chemicals that can
damage, weaken, or destroy plastic.
An extension cord should not be used unless absolutely necessary. Use of
an improper extension cord could result in a risk of fire and electric shock.
If an extension cord must be used, make sure that:
The pins on plug of extension cord are the same number, size and shape as
those of the plug on charger.
The cord is properly wired and in good electrical condition
The size is large enough for AC ampere rating of charger as specified below:
The Cord Length (Feet) 25’ 50’ 100’
Cord Size (AWG) 16 16 16
NOTE: AWG = American Wire Gauge
Do not operate the charger with a damaged cord or plug, which could
cause shorting and electric shock. If damaged, have the charger repaired
or replaced by an authorized service technician at an Authorized Service
Center.
Do not operate the charger if it has received a sharp blow, been dropped,
or has otherwise been damaged in any way. Take it to an authorized
service technician at an Authorized Service Center for an electrical check
to determine if the charger is in good working order.
Do not disassemble the charger. Take it to an authorized service
technician at an Authorized Service Center when service or repair is
required. Incorrect reassembly may result in a risk of electric shock or fire.
Unplug the charger from the electrical outlet before attempting any
maintenance or cleaning to reduce the risk of electric shock.
Disconnect the charger from the power supply when not in use. This will
reduce the risk of electric shock or damage to the charger if metal items
should fall into the opening. It will also help prevent damage to the charger
during a power surge.
Risk of electric shock. Do not touch the uninsulated portion of the output
connector or uninsulated battery terminal.
Save these instructions. Refer to them frequently and use them to instruct
others who may use this tool. If you lend this tool to someone else, also
lend these instructions to them to prevent misuse of the product and
possible injury.
Page 6
10
11
PRODUCT SPECIFICATIONS
Motor 18 Volt DC
Switch VSR (Variable Speed Reversible)
No Load Speed LO: 0-300 RPM / HI: 0-1300 RPM
Hammer LO: 0-3900 BPM / HI: 0-16900 BPM
Clutch 24 position
Chuck
1/2” (13mm), ratcheting, single-
sleeve keyless
Max torque 480in.lbs
Charging time 75 Min
Drill Weight 3.06 lbs
Battery Voltage 18 Volt DC
Charger Input 120-Volts, 60 Hz AC only
Optimum Charging Temperature 32°F (0° C) -122°F (50°C)
WARNING! The safe use of this product requires an understanding of
the information included on the tool and in this operator’s manual, as well as
knowledge of the project you are attempting. Before using this product, familiarize yourself with all operating features and safety rules.
ADJUSTABLE TORQUE
The drill has 24 screw-driving positions.
TWO-SPEED GEAR BOX
The two-speed gear box is designed for drilling or driving at LO or HI speeds.
A slide switch is located on top of your hammer drill for selecting the
appropriate setting.
VARIABLE SPEED
The variable-speed trigger switch delivers higher speed with increased
trigger pressure and lower speed with decreased trigger pressure.
RATCHETING KEYLESS CHUCK
The keyless chuck allows you to hand-tighten or release the drill bit in the
chuck jaws. The ratcheting feature is designed to prevent the chuck from
opening during operation.
DESCRIPTION
KNOW YOUR HAMMER DRILL (Fig. 1)
Before attempting to use this hammer drill, familiarize yourself with all of its
operating features and safety requirements.
WARNING! Do not allow familiarity with your hammer drill to make you
careless. Remember that a careless fraction of a second is sufficient to inflict
severe injury.
Ratcheting
keyless
chuck
LED worklight
Battery release button
Power display button
Power display Battery pack
Anti-vibration handle
Torque
adjustment
ring
Hammer/screw/drill
mode selection ring
Two-speed
gearbox switch
Fig. 1
Page 7
12
13
FORWARD/REVERSE/CENTER LOCK
The direction-of-rotation selector located above the trigger switch changes
the direction of bit rotation. Setting the trigger switch in the OFF (center lock)
position helps reduce the possibility of accidental starting when not in use.
LED WORKLIGHT
Pressing the trigger switch illuminates the LED worklight, located on the front
of the drill. This feature provides extra light for increased visibility.
ASSEMBLY
WARNING! If any part is broken or missing, DO NOT attempt to plug in the
power cord or operate the drill until the broken or missing part is replaced.
Failure to do so could result in possible serious injury.
WARNING! Do not attempt to modify this hammer drill or create accessories not recommended for use with this hammer drill. Any such alteration
or modification is misuse and could result in a hazardous condition leading to
possible serious injury.
WARNING! To prevent accidental starting that could cause serious personal injury, always remove the battery pack from the drill when assembling
parts.
UNPACKING
This product has been shipped completely assembled.
Carefully remove the tool and any accessories from the box. Make sure
that all items listed in the packing list are included.
Inspect the tool carefully to make sure no breakage or damage occurred
during shipping.
Do not discard the packing material until you have carefully inspected and
satisfactorily operated the tool.
PACKING LIST
Hammer drill, double ended bit, auxiliary handle, 2 Lithium-Ion battery packs,
charger, soft case and Operator’s Manual
OPERATION
POWER INDICATOR (Fig.2)
This Li-ion battery pack is equipped with a power indicator that displays the
battery pack’s charge status. Press the power indicator button to display the
LED lights. The LED lights will stay lit for approximately 4 seconds.
NOTE: The power indicator can be used whether the battery is attached to
or removed from tool.
80-100%
Charge
60-79%
Charge
40-59%
Charge
20-39%
Charge
Under 20%
Charge
High/low temperature
LOW CAPACITY WARNING
If one LED on the power indicator begins to flash, the battery pack’s charge is
under 20% capacity and should be recharged.
Unlike other battery pack types, Lithium-Ion battery packs deliver fade-free
power for their entire run time. The tool will not experience a slow, gradual
loss of power as you work. To signal that the battery pack is at the end of
its run time and needs to be charged, power to the tool will drop quickly.
The power indicator will begin to display four flashing LED lights when it
is completely discharged. When this happens, remove the tool from the
workpiece and charge the battery pack as needed.
BATTERY PROTECTION
To protect the battery from damage and prolong its life, the battery pack
circuitry will turn off the battery pack if it becomes overloaded or if the
temperature becomes too high during use. This may happen in extremely
high torque, binding and stalling situations. The battery pack will begin
normal operation when it cools down.
The power indicator will display four flashing LED lights if the circuitry
detects a momentary overload. You can conveniently reset the battery pack
by releasing the power-tool trigger. Press the power indicator button again to
display the remaining charge.
Fig. 2
Page 8
14
15
NOTE: If the power indicator continues to flash four LED lights after resetting,
place the battery pack on the charger to evaluate the battery condition.
NOTE: A significantly reduced run time after fully charging the battery
pack indicates that the battery is near the end of its usable life and must be
replaced.
COLD WEATHER OPERATION
When the battery pack is very cold, it may “pulse” for the first minute of
use to warm itself. Put the battery pack on a tool and use the tool in a light
application. After about a minute, the battery pack will have warmed itself
and will operate normally.
WHEN TO CHARGE THE BATTERY PACK
The Lithium-Ion battery can be charged at any time and will not develop a
“memory” when charged after only a partial discharge. It is not necessary
to run down the battery pack charge before recharging. Remove the battery
pack from the tool when it is convenient for you and your job.
Use the power indicator to determine when you need to recharge the
battery pack.
You can “top-off” your battery pack’s charge before starting a big job or
long period of use.
Due to Lithium-Ion’s fade-free properties, the only time it is necessary to
charge the Lithium-Ion battery pack is when the pack has reached the
end of its charge. To signal the end of charge, power to the tool will drop
quickly. Charge the battery pack as needed.
HOW TO CHARGE THE BATTERY PACK
NOTE: This Lithium-Ion battery pack is shipped partially charged. Before
using it the first time, fully charge the battery pack.
A fully discharged battery pack will charge in about 75 minutes (for included
battery pack 252-8032) in a surrounding temperature between 41° F (5° C) and
122° F (50° C).
1. Charge the battery pack with the
correct charger.
2. Connect the charger to a power
supply.
3. Attach the battery pack to the
charger by aligning the raised ribs
of the battery pack with the slot in
the charger. Slide the battery pack
onto the charger (Fig. 3)
4. The Charger will communicate with the battery pack’s circuitry to evaluate
the condition of the battery pack.
5. During normal charging, the green LED on the charger will flash
continuously.
6. After charging is complete, the green LED on the charger will be on. The
power indicator LED lights will not be displayed when the power indicator
button is pressed while the battery pack is on the charger.
7. The battery pack will fully charge, but will not overcharge, if left on the
Charger.
LED FUNCTIONS OF CHARGER (Fig. 4)
LED INDICATOR
BATTERY
PACK
RED LED
GREEN
LED
ACTION
HI / LO TEMP.
Hot/Cold
battery
On Off
Fast charge will begin
when battery returns
to 41
o
F (5oC) and 122oF
(50
o
C)
DEFECTIVE
BATTERY
HI / LO TEMP.
Defective Flashing Off
Battery pack or
charger is defetive
DEFECTIVE
BATTERY
BATTERY
CHARGING
HI / LO TEMP.
Charging Off Flashing Charging
DEFECTIVE
BATTERY
BATTERY
CHARGING
BATTERY
FULL
HI / LO TEMP.
Fully
charged
Off On Charging is complete
CHARGING A HOT BATTERY PACK
If the battery pack is above normal temperature range, the red LED will
illuminate and the green LED will be off. When the battery pack cools down
to approximately 122°F (50°C), the charger will automatically begin charging.
CHARGING A COLD BATTERY PACK
If the battery pack is below the normal temperature range, the red LED
will illuminate and the green LED will be off. When the battery warms to a
temperature of more than 41°F (5°C), the charger will automatically begin
charging.
Li-ion
Use only with charger 252-8036.
Model #: 252-8028
Fig. 3
Page 9
16
17
DEFECTIVE BATTERY
If the charger detects a problem, the red LED will begin flashing and the
green LED will be off.
1. If registering as defective, remove and reinsert the battery pack in the
charger. If the LED status reads “defective” a second time, try charging a
different battery pack.
2. If a different battery pack charges normally, dispose of the defective
battery pack (see Maintenance section).
3. If a different battery pack also indicates “defective,” the charger may be
defective.
BATTERY CHARGING
If the battery pack is within normal temperature range, the green LED will
begin flashing and the red LED will be off. The battery pack included with this
product reach a full charge in 75 minutes. The power indicator LED lights will
cycle from right to left during charging. This is part of the normal charging
operation.
BATTERY FULL
When fully charged, the green LED Light on the charger will be on and the
red LED light will be off.
NOTE: The battery pack will fully charge, but will not overcharge, if left on the
charger.
NOTE: The power indicator LED lights will not be displayed when the power
indicator button pressed while the battery pack is still on the charger.
NOTE: Charger may warm with several continuous charge cycles. This is part
of the normal operation of the charge. Charge in a well ventilated area.
TO ATTACH BATTERY PACK (Fig. 5)
1. Lock the trigger switch on the drill
by placing the direction of rotation
(forward/reverse/center lock)
selector in center position
2. Align the raised portion on the
battery pack with the grooves on
the bottom of the drill, and then
attach the battery pack to the drill
as shown.
3. Make sure that the latch on the battery pack snaps into place and the
battery pack is secured to the drill before beginning operation.
TO DETACH BATTERY PACK (Fig. 5)
1. Lock the trigger switch on the drill by placing the direction of rotation
(forward/ reverse/ center lock) selector in center position.
2. Depress the battery release buttons located on the front of the battery
pack to release the battery pack.
3. Pull forward on the battery pack to remove from the tool.
CAUTION! When placing the battery pack in the tool, be sure that the
raised rib on battery pack aligns with the groove on the drill and the latches
snap into place properly. Improper assembly of the battery pack can cause
damage to internal components.
USING THE AUXILIARY HANDLE ASSEMBLY
WARNING! To reduce the risk of injury, always use the auxiliary handle
when operating, hold the tool with both hands to maximize control.
The auxiliary handle must be tightened sufficiently to resist the twisting
action of the tool if the accessory binds or stalls. Be sure to grip the side
handle at the far end to control the tool during a stall.
The auxiliary handle can be attached to either side for left or right hand use.
TRIGGER SWITCH (Fig. 6a)
To turn the drill ON, depress the
trigger switch. To turn it OFF, release
the trigger switch.
VARIABLE SPEED (Fig.6a)
The variable-speed trigger switch
delivers higher speed with increased
trigger pressure and lower speed
with decreased trigger pressure.
DETACH
ATTACH
Fig. 5
Direction-of-rotation
selector
Variable-speed
trigger switch
Fig. 6a
Page 10
18
19
DIRECTION-OF-ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK) (Fig. 6b)
The direction of bit rotation is
reversible and is controlled by a
selector located above the trigger
switch.
With the drill held in normal operating
position:
1. Position the direction of rotation
selector to the left of the tool for
forward rotation.
2. Position the direction of rotation
selector to the right of the tool for
reverse rotation.
3. Setting the switch in the OFF (center lock) position helps reduce the
possibility of accidental starting when not in use.
CAUTION! To prevent gear damage, always allow the chuck to come to
complete stop before changing the direction of rotation.
NOTE: The hammer drill will not run unless the direction of rotation selector
is engaged fully to the left or right.
ELECTRIC BRAKE
To stop the hammer drill, release the trigger switch and allow the chuck to
come to a complete stop. The electric brake quickly stops the chuck from
rotating. This feature engages automatically when you release the trigger
switch.
RATCHETING KEYLESS CHUCK (Fig.7)
The hammer drill has a ratcheting
keyless chuck to tighten or release
drill bits in the chuck jaws. The
arrows on the chuck indicate which
direction to rotate the chuck body
in order to GRIP (tighten) or OPEN
(release) the chuck jaws on the
drill bit. The ratcheting feature is
designed to prevent the chuck from
opening during operation.
WARNING! Do not hold the chuck body with one hand and use the power
of the drill to tighten the chuck jaws on the drill bit. The chuck body could slip
in your hand, or your hand could slip and come in contact with the rotating bit.
This could cause an accident resulting in serious personal injury.
TWO-SPEED GEAR BOX (Fig. 8)
The drill has a two-speed gear box
designed for drilling or driving at
LO or HI speeds. A slide switch is
located on the top of the drill to
select either LO or HI speed.
When using the drill in the LO speed
range, the speed will decrease and
the drill will have more power and
torque. When using the drill in the HI
speed range, the speed will increase
and the drill will have less power and torque. Use LO speed for high power
and torque applications and HI speed for fast drilling or driving applications.
Use LO speed for starting holes without a center punch, drilling metals or
plastic, drilling ceramics, or in applications requiring a higher torque (see
below).
HI speed is better for drilling wood and wood composites and for using
abrasive and polishing accessories.
NOTE: Avoid running the drill at LO speed for extended periods of time.
Running at LO speed under constant usage may cause the drill to become
overheated. If this occurs, cool the drill by running it without a load at HI
speed.
NOTE: Never change gears while the tool is running. Failure to obey this caution could result in serious damage to the drill.
SCREWDRIVING/DRILLING/
HAMMER DRILLING MODE
SELECTION (Fig.9)
To select the mode, rotate the
mode selection ring until the icons
align with the arrow and clicks into
position.
Keyless chuck
GRIP
(Tighten)
OPEN
(Release)
Fig. 7
Two-speed gearbox switch
Fig. 8
FORWARD REVERSE
Fig. 6b
Mode selection ring
Arrow
Fig. 9
Page 11
20
21
Screwdriving
Rotate the mode selection ring so the screw symbol is aligned with the
arrow.
Set the torque adjustment ring to the appropriate number setting for the
torque desired.
Drilling
NOTE! When the mode selection ring is in the drill or hammer drill mode, the
clutch will not slip, regardless of the position of the torque adjustment ring.
Rotate the mode selection ring so the drill symbol is aligned with the arrow.
NOTE: The torque adjustment ring may be set on any number.
Hammer drilling
Rotate the mode selection ring so the hammer symbol is aligned with the
arrow.
ADJUSTABLE TORQUE CLUTCH (Fig.
10)
The torque clutch can be adjusted
to 24 different settings. The higher
the torque setting, the more force
the drill produces to turn an object in
either LO or HI rotation speed.
When using the drill for different
driving applications, it is necessary
to increase or decrease the torque
to help prevent the possibility of
damaging screw heads, threads, workpiece, etc.
Adjust the torque by rotating the torque-adjustment ring.
The proper setting depends on the job and the type of bit, fastener, and
material you will be using. In general, use greater torque for larger screws,
but if the torque is too high, the screws may be damaged or broken.
For delicate operations, such as removing a partially stripped screw, use
a low torque setting. For operations such as drilling into hardwood, use a
higher torque setting.
NOTE: When adjusting the torque ring make sure that the speed switch is
either completely in the LO or HI position.
CAUTION! Do not change the torque setting when the tool is running.
LED WORKLIGHT (Fig. 11)
The LED worklight, located on the
base of the drill, will illuminate when
the trigger switch is depressed.
The LED worklight will turn off
when the trigger switch is released.
This provides additional light on
the surface of the workpiece for
operation in lower-light areas.
INSTALLING BITS (Fig. 12a)
1. Lock the trigger switch by placing
the direction of rotation selector in
the OFF (center) position.
2. Open or close the chuck jaws to a
point where the opening is slightly
larger than the bit size you intend
to use.
3. Insert a drill bit.
NOTE: Rotate the chuck body in the
direction of the arrow marked GRIP
to close the chuck jaws. Do not use
a wrench to tighten or loosen the
chuck jaws.
4. Tighten the chuck jaws securely
on the bit.
REMOVING BITS (Fig. 12b)
1. Lock the trigger switch by placing
the direction of rotation selector in
the OFF (center) position.
2. Open the chuck jaws.
NOTE: Rotate the chuck body in the
direction of the arrow marked OPEN
to open the chuck jaws. Do not use a wrench to tighten or loosen the chuck
jaws.
3. Remove the drill bit.
LED worklight
Fig. 11
Torque
adjustment
ring
To increase torque
To decrease torque
15
17
19
21
23
Fig. 10
Fig. 12b
Keyless chuck
GRIP
(Tighten)
OPEN
(Release)
Fig. 12a
Page 12
22
23
WARNING! Make sure to insert the drill bit straight into the chuck jaws.
Do not insert the drill bit into the chuck jaws at an angle and then tighten it, ,
as shown in figure 12b. This could cause the drill bit to be thrown from the drill,
resulting in possible serious personal injury or damage to the chuck.
GENERAL DRILLING (Fig. 13)
1. Check the direction of rotation
selector for the correct setting
(forward or reverse).
2. Secure the material to be drilled
in a vise or with clamps to keep it
from turning as the drill bit rotates.
3. Hold the drill firmly and place the
bit at the point to be drilled.
4. Depress the trigger switch to start
the drill.
5. Move the drill bit to contact the
workpiece, applying only enough pressure to keep the bit cutting. Do not
force the drill or apply side pressure to elongate a hole. Let the tool do the
work.
6. When drilling hard, smooth surfaces, use a center punch to mark the
desired location of the hole before beginning to drill. This will prevent the
drill bit from slipping off-center as the hole is started.
7. When drilling metals, use light oil on the drill bit to keep it from
overheating. The oil will prolong the life of the bit and increase the drilling
action.
8. If the bit jams in the workpiece or if the drill stalls, stop the tool
immediately. Remove the bit from the workpiece and determine the reason
for jamming.
WARNING! This drill is equipped with an electric brake. When the brake is
functioning properly, sparks may be visible through the vent slots in the housing. This is normal and is the action of the brake.
DRILLING MODE OPERATION
1. Select the desired speed to match the planned operation.
2. For wood drilling, use twist bits, spade bits, power auger bits or hole
saws. Begin drilling at a very low speed to prevent the bit from slipping
off the starting point, and increase the speed as the drill bit bites into the
material. When drilling “through” holes, place a block of wood behind the
workpiece to prevent ragged or splintered edges on the back side of the
hole.
3. For metal drilling, use high speed steel twist drill bits. Begin drilling at
a very low speed to prevent the bit from slipping off the starting point.
Maintain a speed and pressure which allows cutting without overheating
the bit.
4. Use light oil on the drill bit to keep it from overheating; the oil will prolong
the life of the bit and increase the drilling action.
5. If the drill stalls, it is usually because it is being overloaded. Release the
trigger switch immediately, remove drill bit from the work, , and determine
cause of stalling.
6. Keep the motor running when pulling the bit back out of drilled hole. This
will prevent jamming.
HAMMER DRILLING MODE OPERATION
1. When hammer drilling, use just enough force on the drill to keep it from
bouncing excessively. Too much force will cause slower drilling speeds,
overheating and a lower drilling rate.
2. Do not exert side pressure on the bit when drilling as this will cause
clogging of the bit flutes and a slower drilling speed.
3. When drilling deep holes, if the drill speed starts to drop off, pull the bit
partially out of the hole with the tool still running to help clear debris from
the hole.
4. For masonry, use carbide-tipped bits or masonry bits. A smooth, even flow
of dust indicates the proper drilling rate.
WARNING! Always wear safety goggles or safety glasses with side shields
during power tool operation or when blowing dust. If operation is dusty, also
wear a dust mask.
SCREWDRIVER OPERATION
1. Select the desired speed/torque range to match the planned operation.
2. Attach the desired fastener accessory into the chuck.
3. Make a few practice runs in scrap piece before working.
Fig. 13
Page 13
24
25
MAINTENANCE
GENERAL MAINTENANCE
WARNING! To avoid personal injury, always remove the battery pack from
the tool when cleaning or performing any maintenance.
The tool may be cleaned most effectively with compressed dry air. Always
wear safety goggles when cleaning tools with compressed air.
Avoid using solvents when cleaning plastic parts. Most plastics are
susceptible to damage from various types of commercial solvents and may
be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease,
etc.
WARNING! When servicing, use only identical replacement parts. Use of
any other parts may create a hazard or cause product damage. To ensure
safety and reliability, all repairs should be performed by a qualified service
technician at Authorized Service Center.
BATTERIES:
The battery pack is equipped with Lithium-Ion rechargeable batteries. The
duration of use from each charge will depend on the type of work performed.
The batteries in this tool have been designed to provide maximum troublefree life. Like all batteries, they will eventually wear out. Do not disassemble
the battery pack or attempt to replace the batteries. Handling of the batteries,
especially when wearing rings and jewelry could result in a serious burn.
To obtain the longest possible battery life, read and understand the operator’s
manual.
It is good practice to unplug the Charger/Adapter and remove the Lithium-
Ion battery pack when not in use.
For Lithium-Ion battery pack storage longer than 30
days:
Store the Lithium-Ion battery pack where the
temperature is below 80°F (26°C) and free of
moisture.
Store Lithium-Ion battery packs in a 30%-50%
charged condition.
Every six months of storage, fully charge the
Lithium-Ion battery pack.
Exterior may be cleaned with a cloth or soft non-metallic brush.
BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING
To preserve natural resources, please recycle or dispose of batteries
properly. This product contains lithium-ion batteries. Local, state, or federal
laws may prohibit disposal of lithium-ion batteries in ordinary trash. Consult
your local waste authority for information regarding available recycling and/
or disposal options.
WARNING! Upon removal of the battery pack for disposal or recycling,
cover the battery pack’s terminals with heavy-duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its components.
Lithium-Ion batteries must be recycled or disposed of properly. Also, never
touch both terminals with metal objects and/or body parts as short circuit may
result. Keep away from children. Failure to comply with these warnings could
result in fire and/or serious injury.
CHUCK REMOVAL (Fig. 14)
The chuck can be removed and
replaced with a new one.
1. Lock the trigger switch by placing
the direction of rotation selector in
center position.
2. Open the chuck jaws. Using a
screwdriver, remove the chuck
screw by turning it in a clockwise
direction.
3. Insert a 5/16-in. or larger hex key
into the chuck of the drill and
tighten the chuck jaws securely.
4. Tap the hex key sharply with a mallet in a anti-clockwise direction. This will
loosen the chuck for easy removal.
5. Attach a new chuck to the spindle and tighten the chuck screw.
Mallet
Hex key
Chuck
Fig. 14
Page 14
26
27
TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
The drill does not work Battery is depleted Charge the battery
Bit cannot be installed
Sleeve is not released Release the sleeve
Bit does not fit the sleeve Use suitable adapter
Motor overheating
Be sure cooling vents
are free from dust and
obstacles
Clean, clear vents. Do
not cover with hand
during operation
WARRANTY
3-MONTH MONEY BACK GUARANTEE:
This MASTERFORCE™ brand power tool carries our 3-Month Money Back
Guarantee. If you are not completely satisfied with your MASTERFORCE™
brand power tool for any reason within three (3) months from the date of
purchase, return the tool with your original receipt to any retail store, and
we will provide you a refund – no questions asked.
3-YEAR LIMITED WARRANTY:
This MASTERFORCE™ brand power tool carries our famous No Hassle 3-Year
Limited Warranty to the original purchaser. If the tool fails within three (3)
years from the date of purchase, simply bring this tool and its sale receipt
back to your nearest retail store for a free equivalent replacement within
those three years. Notwithstanding the foregoing, this limited warranty
does not cover any damage that has resulted from abuse or misuse of the
Merchandise. This warranty: (1) excludes expendable parts including but
not limited to blades, belts, bits, light bulbs, and/or batteries; (2) shall be void
if this tool is used for commercial and/or rental purposes; and (3) does not
cover any losses, injuries to persons/property or costs. This warranty does
give you specific legal rights and you may have other rights, which vary
from state to state. Be careful, tools are dangerous if improperly used or
maintained. Seller’s employees are not qualified to advise you on the use
of this Merchandise. Any oral representation(s) made will not be binding
on seller or its employees. The rights under this limited warranty are to
the original purchaser of the Merchandise and may not be transferred to
any subsequent owner. This limited warranty is in lieu of all warranties,
expressed or implied including warranties or merchantability and fitness for
a particular purpose. Seller shall not be liable for any special, incidental, or
consequential damages. The sole exclusive remedy against the seller will be
for the replacement of any defects as provided herein, as long as the seller
is willing or able to replace this product or is willing to refund the purchase
price as provided above. For insurance purposes, seller is not allowed to
demonstrate any of these power tools for you.
For questions / comments, technical assistance or repair parts –
Please Call Toll Free at: 1-866-917-4374 (M-F 8am – 6pm)
SAVE YOUR RECEIPTS. THIS WARRANTY IS VOID WITHOUT THEM.
Page 15
28
Loading...