Mastercraft Mbs-1500ef, Mbs-1500e, Mbs-1500efc Owner's Manual

1000 / 1500 / 2000 RPM

BURNISHERS

SAFETY,

READ & FOLLOW ALL INSTRUCTIONS,

PERATION

O

&

MAINTENANCE

MANUAL

WARNINGS & CAUTIONS

BEFORE USING THIS BURNISHER

This burnisher will afford you many years of
trouble free operating satisfaction if it is
given proper care. All parts have passed
rigid quality control standards before being
assembled to produce the finished product.
Prior to packaging, the units again inspect­ed for assurance of flawless assembly.

Your burnisher was protectively packed to
prevent damage in shipment. We recom­mend that upon delivery, remove the unit
from its carton and carefully inspect it for
any possible damage in transit.

SAVE THESE INSTRUCTIONS

If damage is discovered, immediately notify
the transportation company that delivered
your burnisher. As a shipper, we are
unable to act upon any claim for concealed
damage. You must originate any claim
within 5 days of delivery.

These instructions are for your protection
and information. PLEASE READ CAREFUL-
LY ! Failure to follow these precautions could
result in injury or discomfort.

AGE 1

P

Burnisher Manual - PN 344249 - Printed in USA 05/12/06

READ ALL

INSTRUCTIONS

BEFORE

OPERATING

IMPORTANT
SAFETY

NSTRUCTIONS

I

WARNING:

To reduce the risk of fire, electric shock or injury:

When using an electric burnisher, basic precautions should

always be following, including the following:

1) DO NOT leave burnisher plugged in

when not in use. Unplug from outlet when
not in use and before servicing.

2) Electric shock could occur if exposed to
rain. Store indoors.

3) This is NOT a toy. Close attention is nec­essary when used around or near children.

4) Use only as described in this manual.
Use only manufacturer's recommended
attachments.

5) DO NOT use with damaged cord plug.
When burnisher is not working as it should
because it has been dropped, damaged,
left outdoors, or dropped into water, con­tact the manufacturer or authorized serv­ice center.

6) DO NOT pull or carry by the cord, use
power cord as a handle, close a door on
cord, or pull cord around sharp edges or
corners. DO NOT run burnisher over cord.
Keep cord away from heated surfaces.

7) DO NOT handle the burnisher plug with
wet hands.

8) DO NOT unplug by pulling on the cord.
To unplug, grasp the plug, not the power
cord.

9) DO NOT put any objects into motor
openings.

10) Keep hair, loose clothing, fingers and
all parts of body away from moving parts.

11) DO NOT operate where oxygen or
anesthetics are used.

12) DO NOT use around flammable or com­bustible liquids such as gasoline or use in
areas where they may be present.

13) DO NOT use an extension cord unless
absolutely necessary. If an extension cord
is used, then wire size must be #14 gauge
or thicker and should not exceed 50 feet in
length. Extension cord must be three-wire
type to insure grounding protection.

14) Replace damaged or worn parts
immediately with genuine original equip­ment parts to maintain safety and to pro­tect your limited warranty.

GROUNDING
SAFETY

NSTRUCTIONS

I

DANGER:

Improper use of the grounding plug can result in a risk

of electric shock.

This burnisher must be grounded. If it
should malfunction or breakdown, ground­ing provides a path of least resistance for
electrical current to reduce the risk of elec­tric shock. The burnisher is equipped with
a cord having an equipment-grounded plug.
The plug must be inserted into an appropri­ate outlet that is properly installed and
grounded in accordance with all local
codes and ordinances

PAGE 2

If repair or replacement of the cord or plug
is necessary, DO NOT connect the ground­ing wire to either flat blade terminal. The
wire with insulation having an outer surface
that is green with or without yellow stripes
is the grounding wire.