MasterCraft 175 RPM Maintenance Manual
175 RPM
TANDARD
S
FLOOR MACHINE
SAFETY &
AINTENANCE
M
MANUAL
This unit is intended for commercial use.
READ
& FOLLOW ALL INSTRUCTIONS,
WARNINGS & CAUTIONS
BEFORE USING THIS FLOOR MACHINE
This floor machine will afford you many years
of trouble free operating satisfaction if it is
given proper care. All parts have passed
rigid quality control standards before being
assembled to produce the finished product.
Prior to packaging, the units are again
inspected for assurance of flawless assembly.
This floor machine was protectively packed
to prevent damage in shipment. We recommend that upon delivery, remove the unit
from its carton and carefully inspect it for
any possible damage in transit.
If damage is discovered, immediately notify
the transportation company that delivered
your floor machine. As a shipper, we are
unable to act upon any claim for concealed
damage. You must originate any claim within
5 days of delivery.
These instructions are for your protection
and information. PLEASE READ CAREFUL-
LY! Failure to follow these precautions could
result in injury or discomfort.
Treat this floor machine as you would any
other high grade precision made product.
Throwing, dropping, unreasonable bumping
across thresholds and other misuse may
result in a damaged unit and invalidate the
warranty.
PLEASE READ
CAREFULLY
BEFORE
OPERATING
SAVE THESE INSTRUCTIONS
PAGE 1
175 RPM Floor Machine Manual - PN 344346 Rev C - Printed in USA 11/29/05
IMPORTANT
WARNING:
SAFETY
INSTRUCTIONS
1) DO NOT leave this machine plugged in
when not in use. Unplug from outlet when
not in use and/or before servicing.
2) Electric shock could occur if exposed to
rain. Store indoors.
3) This is NOT a toy. Close attention is necessary when used around or near children.
4) Use only as described in this manual.
Use only manufacturer's recommended
attachments.
5) DO NOT use with damaged cord plug.
If the floor machine is not working as it
should because it has been dropped, damaged, left outdoors, or dropped into water,
contact the manufacturer or authorized
service center.
ROUNDING
G
INSTRUCTIONS
To reduce the risk of fire, electric shock or injury;
Read all instructions before using this floor machine.
When using this floor machine, basic precautions should always be followed,
including the following:
6) DO NOT pull or carry by cord, use power
cord as a handle, close a door on cord, or
pull cord around sharp edges or corners.
DO NOT run floor machine over the cord.
Keep cord away from heated surfaces.
7) DO NOT handle the plug or operate with
wet hands.
8) DO NOT put any object into the motor
openings.
9) DO NOT unplug by pulling on cord. To
unplug, grasp plug, not the power cord.
10) Keep hair, loose clothing, fingers and
all parts of body away from moving parts.
11) DO NOT operate where oxygen or
anesthetics are used.
This floor machine must be grounded. If it
should malfunction or breakdown, grounding
provides a path of least resistance for electrical current to reduce the risk of electric
shock. This machine is equipped with a cord
having an equipment-grounded plug. The
plug must be inserted into an appropriate
outlet that is properly installed and grounded
12) DO NOT use around flammable or
combustible liquids such as gasoline or use
in areas where they may be present.
13) DO NOT use an extension cord unless
absolutely necessary. If an extension cord is
used, then wire size must be #14 gauge or
thicker and should not exceed 50 feet in
length. Use only a 3 wire grounded extension cord to ensure grounding protection.
14) Replace damaged or worn parts immediately with genuine original equipment
parts to maintain safety and protect your
limited warranty.
15) Floor sanding can result in an explosive
mixture of fine dust and air. Use a floor
sanding machine only in a well ventilated
area.
in accordance with all local codes and ordinances
If repair or replacement of the cord or plug
is necessary, DO NOT connect the grounding wire to either flat blade terminal. The
wire with insulation having an outer surface
that is green with or without yellow stripes
is the grounding wire.
GROUNDING
METHODS
DANGER:
Improper use of the
grounding plug can
result in a risk of
electrical shock.
Improper connection of the equipment-grounding conductor can result in a risk of electrical shock.
Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded.
NOTE: In Canada, the use of a temporary adaptor is not permitted by the Canadian Electrical Code.
This floor machine is for use on a nominal
120 volt circuit, and has a grounding plug
that looks like the plug illustrated in (Fig A).
A temporary adaptor that looks like the
adaptor illustrated in (Fig B & C) may be
used to connect the plug to a 2-pole receptacle as shown in (Fig A) if a properly
grounded outlet is not available.
ARNING:
W
DO NOT modify the plug provided with the machine. If it will not fit the outlet,
have a proper outlet installed by a qualified electrician.
The temporary adaptor should be used only
until a properly grounded outlet (Fig A) can
be installed by a qualified electrician. The
green color rigid ear, lug, or like extending
from the adaptor must be connected to a
permanent ground such as a properly
grounded outlet box cover. Whenever the
adaptor is used, it must be held in place by
the metal screw (Fig C).
PAGE 2
Loading...