LO
CK
Master Model GT-70 Industrial Torch Instructions
Mode d'emploi du chalumeau industriel modèle GT-70
Instrucciones para el uso del soplete industrial modelo GT-70
Fuel Adjustment Knob
Bouton de réglage du gaz
Perilla de ajuste del gas
Safety Slide Bar
Glissière de sécurité
Barra deslizante de seguridad
Air Control Ring
Anneau de régulation d’air
Anillo de control del aire
Flame Orifice
Orifice de la flamme
Orificio de la flama
Removable
Stand
Base d’appui amovible
Soporte desmontable
Filling Valve
Clapet de remplissage
Válvula de carga
Metal Body
Corps métallique
Cuerpo metálico
Ignition Trigger
Gâchette d’allumage
Gatillo de encendido
Hands Free
ON/OFF slide
Interrupteur «on-off»
à glissière pour utilisation mains libres
Interruptor deslizante
de «on-off» para
operación de manos
libres
BACK
THE GT-70 INDUSTRIAL TORCH DOES NOT CONTAIN BUTANE GAS WHEN PURCHASED
GAS REFILLING
• Use only Master Ultratane™ Butane Fuel.
• Shake gas container a few times to warm fuel up.
• Make sure the Fuel Adjustment Knob is in the “OFF” position (fully clockwise).
• Insert the Butane container nozzle tip vertically down into the unit gas valve
refill opening. Use a pumping action for best results (Figure 1).
• After filling, allow a few minutes for the gas to stabilize.
IGNITION
•Turn the Fuel Adjustment Knob counter-clockwise 1 full turn. (Figure 2)
• To Ignite: Push Safety Slide Bar up and hold while depressing Ignition
Trigger (Figure 3). When you remove pressure from the ignition trigger,
unit will shut off instantly.
• For Hands Free Mode: Push Hands Free ON/OFF slide switch foreword
while depressing trigger (Figure 4). To shut off unit, return slide switch to
“OFF” position.
• Note: It is sometimes difficult to ignite when the Air Control Ring covers
the air control holes. Adjust Accordingly.
FLAME ADJUSTMENT
• Adjust the torch flame length by turning the Fuel Adjustment Knob (+) (-)
(Figure 2). Don’t make the flame too long as it will only waste the gas and
make the flame unstable.
• Turn the Air Control Ring forward to convert the blue pinpoint flame to a
soft/cooler flame. CAUTION: Air Control Ring can be very hot.
STORAGE
•
Turn the Fuel Adjustment Knob clockwise to “OFF” position until snug.
Let tool cool down before storing.
• To prevent gas leakage make sure Hands Free ON/OFF Slide switch is
returned completely to “OFF” position.
WARNINGS:
L
O
C
K
OFF
ON
2
FERMÉ
DESACTIVADO
ENGAGÉ
ACTIVADO
GAS
L
O
C
K
1
4
3
1. Read Instructions Before Operation.
2. Keep out of reach of children.
3. Do not touch flame guard when HOT!
4. Use only Master Ultratane™ Butane Fuel. Butane gas is extremely flammable, please handle
with care.
5.
Always point away from your face, eyes, and body when igniting or during operation.
6. Do not store under direct sunlight or anywhere temperature will exceed 104°F/40°C.
7. Make sure the Fuel Adjustment Knob is firmly closed (Figure 2) and flame is completely
extinguished after using.
8. After using let tool cool down before storing.
9. Keep the nozzle clean from dust and do not drop the torch as these may cause malfunctions.
10. Do not continually use this tool for over 1 hour.
11. Never puncture or dispose of in a fire.
12. Read and follow all instructions and cautions on the fuel canister.
WARNING:
This product, when used for soldering and similar applications, produces chemicals
known
to the state of California to cause cancer and birth defects or other reproductive harm.
WARNING: The Department of Transportation Hazardous Material Regulations forbid carriage of
butane or other flammable gas products on passenger aircraft. Do not pack this item or any other
flammable gas item, in any checked or carry-on baggage.
Contains flammable gas under pressure. Do not use near sparks or open flame. Do not puncture
or incinerate container or store at temperatures above 120°F. Keep out of reach of children.
Loading...