Master TV750 User Manual

GENERAL SAFETY RULES

WARNING:Read and understand all instructions. Failure to follow all instructions list-

ed below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and dark areas invite
accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or
fumes.

• Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Double insulated tools are equipped with a polarized plug (one blade is wider than
the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician
to install a polarized outlet. Do not change the plug in any way. Double insulation

eliminates the need for the three wire grounded power cord and grounded power supply
system.

• Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is grounded.

• Don’t expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords increase the risk of electric shock.

• When operating a power tool outside, use an outdoor extension cord marked "W-A"
or "W." These cords are rated for outdoor use and reduce the risk of electric shock.

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating power tools may result in serious

personal injury.

• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair
can be caught in moving parts. Air vents cover moving parts and should be avoided.

• Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with
your finger on the switch or plugging in tools that have the switch on invites accidents.

• Remove adjusting keys or wrenches before turning the tool on. Awrench or key that is
left attached to a rotating part of the tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enables better control of the tool in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss

of control.

• Do not force tool. Use the correct tool for your application. The correct tool will do the
job better and safer at the rate for which it is designed.

• Do not use tool if switch does not turn it on or off.Any tool that cannot be controlled with
the switch is dangerous and must be repaired.

• Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing the tool. Such preventative safety measures reduce
the risk of starting the tool accidentally.

• Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools, with sharp cutting edges are less likely to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tools operation. If damaged, have the tool serviced
before using. Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool, may become hazardous when used on
another tool.

SERVICE

• Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts. Follow instructions in
the Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of electric shock or injury.

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min........................minutes ......................alternating current

......................direct current

n

o........................no load speed

..........................

Class II Construction

........................earthing terminal

........................safety alert symbol .../min ..................revolutions or

reciprocations
per minute

CAT. NO. TV750 FORM NO.607532-00 PRINTEDIN U.S.A. (AUG-01CD -1)

KEY INFORMA TION YOU SHOULD KNOW :

• Never operate the sander without a recommended sanding disc properly installed
on the hook and loop base.

• The hook and loop pad and white pad brake disk are replaceable parts. If they
become worn, return the unit to a local service center for repair.

• Do not push down—let the sander do the work.

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y
PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR ELPRODUCTO.

INSTRUCTION MANUAL

TV750

5555"""" ((((111122227777mmmmmmmm))))PPPPaaaallllmmmm GGGGrrrriiiipppp

RRRRaaaannnnddddoooommmm OOOOrrrrbbbbiiiitttt SSSSaaaannnnddddeeeerr

rr

SAFETY WARNINGS AND INSTRUCTIONS: DOUBLE INSULATION

Double insulated tools are constructed throughout with two separate layers of electrical
insulation or a double thickness of insulation between you and the tool’s electrical system.
Tools built with double insulation are not intended to be grounded. As a result, your tool is
equipped with a two prong plug which permits you to use extension cords without concern for
maintaining a ground connection.

Double insulation does not take the place of normal safety precautions when operating this
tool. The insulation system is for added protection against injury resulting from a possible
electrical insulation failure within the tool.

REPLACEMENT PARTS: When servicing use only identical replacement parts. Repair or
replace damaged cords.

SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUGS

Polarized plugs (one blade is wider than the other) are used on equipment to reduce the risk
of electric shock. When provided, this plug will fit into a polarized outlet only one way. If the
plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.

SAFETY WARNINGS AND INSTRUCTIONS: SANDERS

• ALWA YS WEAR EYE PROTECTION.

• Clean your tool out periodically.

CAUTION: If you are using your sander as a random orbit polisher and elect to use draw
string bonnets, be sure to tuck the loose ends of the string securely under the bonnet after
tying the knot. Failure to do so may cause serious injury. Check often to assure string ends
remain tucked under bonnet.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-

struction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber. (CCA)

Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks that are specially designed to
filter out microscopic particles.

OTHER IMPORTANT SAFETY W ARNINGS AND INSTRUCTIONS

EXTENSION CORDS

When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. The following table shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the
gage number, the heavier the cord.

SANDING LEAD BASED PAINT

Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the
contaminated dust. The greatest danger of lead poisoning is to children and pregnant
women.
Since it is difficult to identify whether or not a paint contains lead without a chemical analysis,
we recommend the following precautions when sanding any paint:

PERSONAL SAFETY

• No children or pregnant women should enter the work area where the paint sanding is being
done until all clean up is completed.

• A dust mask or respirator should be worn by all persons entering the work area. The filter
should be replaced daily or whenever the wearer has difficulty breathing.

•NOTE: Only those dust masks suitable for working with lead paint dust and fumes should
be used. Ordinary painting masks do not offer this protection. See your local hardware
dealer for the proper (NIOSH approved) mask.

• NO EA TING, DRINKING or SMOKING should be done in the work area to prevent ingesting
contaminated paint particles. Workers should wash and clean up BEFORE eating, drinking
or smoking. Articles of food, drink, or smoking should not be left in the work area where dust
would settle on them.

ENVIRONMENTAL SAFETY

• Paint should be removed in such a manner as to minimize the amount of dust generated.

• Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils

thickness.

• Sanding should be done in a manner to reduce tracking of paint dust outside the work area.

CLEANING AND DISPOSAL

• All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the
duration of the sanding project. Vacuum filter bags should be changed frequently.

• Plastic drop cloths should be gathered up and disposed of along with any dust chips or

1

TWO SPEED ON OFF SWITCH

INTERRUPTEUR À DEUX VITESSES

INTERRUPTOR DE ENCENDIDO Y APAGADO DE DOS VELOCIDADES

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300

AmpereRating

More Not more American Wire Gage
Than Than

0-6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

1-800-544-6986

®

other removal debris. They should be placed in sealed refuse receptacles and disposed of
through regular trash pick-up procedures. During clean up, children and pregnant women
should be kept away from the immediate work area.

• All toys, washable furniture and utensils used by children should be washed thoroughly
before being used again.

SAVE THESE INSTRUCTIONS

MOTOR

Be sure your power supply agrees with the nameplate marking. Amarking of 120 volts, 50/60
Hz or 120 volts, AC only means that the tool is designed to operate on normal 120 volt house
current. Voltage decrease of more that 10% will cause loss of power and overheating. All
Black & Decker tools are factory tested. If this tool does not run, check the power supply.

ASSEMBLY/ADJUSTMENT SET -UP

WARNING: Always unplug sander from power supply before any of the following opera-

tions.

AT TACHING HOOK AND LOOP SANDING DISCS

Your sander is designed to use 5” (127mm) sanding discs with the 8 hole dust extraction
pattern. To attach the sanding disc, carefully center it over the sanding pad ensuring that the
holes in the disc align with the holes in the pad and press the disc firmly in place. The hook
and loop fastening system sanding disc can be easily removed by simply pulling it off. It can
be reused as desired.

OPERATING INSTRUCTIONS

WARNING: To reduce the risk of serious personal injury, read, understand and follow all

important safety warnings and instructions prior to using this tool.

SWITCH

To turn the tool ON, hold it as shown in Fig. 1 and push the portion of the switch marked"I" for
low speed and the portion marked “II” for high speed. The center position marked "O" is OFF.

NOTE: Always return the switch to the "OFF" position before changing operating speed.
Use the high speed for fast material removal and the low speed for a finer finish.

OPERATION

Grasp the sander as shown and turn it ON. Move it in long, sweeping strokes along the
surface, letting it do the work. Pushing down on the tool while sanding actually slows the
removal rate and produces an inferior quality finish.

Check your work often. This sander is capable of removing material rapidly .

DUST COLLECTION

WARNING: Collected sanding dust from sanding surface coatings (polyurethane,
linseed oil, etc.) can self-ignite in sander dust bag or elsewhere and cause fire. To
reduce risk, empty bag frequently and strictly follow sander manual and coating
manufacturer's instructions.

Your sander comes equipped with a cloth canister to collect the dust generated while
sanding. To attached the canister to the sander , fit it firmly onto the dust extraction port at the
back of the sander.

To empty the canister, remove it from the dust port and dump the sanding debris into an
appropriate trash receptacle.

You may, if you prefer, attach a vacuum cleaner to the tool to collect the dust as you sand.
Simply remove the dust bag and install the vacuum hose over or into the dust extraction port.
Shop vacuums come with two diameters of hoses and the dust extraction port is designed to
accept both of them.

Ensure that the vacuum cleaner can be placed such that it will not tip over or interfere with the
motion of the sander. If this cannot be done, do not use the vacuum cleaner. Turn on the
vacuum cleaner before beginning to sand and turn it off after turning off the sander. Empty
vacuum cleaner as required.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts.

30 DAY SATISF ACTION GUARANTEE

If, for any reason, you are not completely satisfied with the performance or results of this
product, within thirty days of original purchase, it will be repaired or replaced free of charge.
Simply provide proof of purchase and return the tool to your place of purchase.

If your tool requires out of warranty repairs, you may send or take your tool to a Black &
Decker owned Service Center. Black & Decker Service Centers are listed under “Tools­Electric” in the yellow pages of the phone directory or you may call 1-800-544-6986 for
information on your nearest Service Center.

TWO YEAR QUALITY GUARANTEE

This product is warranted for two years against any defects in material and workmanship, If
defective, the product will be repaired or replaced free of charge. Simply provide proof of
purchase and return the tool to your place of purchase. Normal wear or damage due to
abuse, mishandling or unauthorized repair is not covered. This warranty does not apply to
accessories, This warranty gives you specific legal rights and you may have other rights
which vary from state to state.

TruServ

8600 W. Bryn Mawr Ave.

Chicago, IL 60631-3505

• Éloigner les curieux, les enfants et les visiteurs de la zone de travail lorsqu'on utilise

un outil électrique. Une distraction peut entraîner la perte de maîtrise de l'outil.

MESURES DE SÉCURITÉ RELATIVES À L'ÉLECTRICITÉ

• Les outils à double isolation comportent une fiche polarisée (une lame plus large

que l'autre). La fiche n'entre que d'une façon dans une prise polarisée. Lorsque la
fiche n'entre pas à fond dans la prise, essayer de nouveau après avoir inversé les
broches de la fiche. Si la fiche n'entre toujours pas dans la prise, communiquer avec
un électricien certifié afin de faire installer une prise polarisée. Ne modifier en
aucune façon la fiche. La double isolation élimine le besoin d'un cordon trifilaire mis à
la terre et d'un système d'alimentation mis à la terre. Valable seulement pour les outils
de classe II (à double isolation).

• Éviter de toucher à des surfaces mises à la terre comme des tuyaux, des radiateurs,

des cuisinières et des réfrigérateurs. Les risques de secousses électriques sont plus

élevés si le corps de l'utilisateur est mis à la terre.

• Protéger les outils électriques de la pluie ou des conditions mouillées. Une infiltration
d'eau dans l'outil augmente les risques de secousses électriques.

• Manipuler le cordon avec soin. Ne jamais se servir du cordon afin de transporter
l'outil ni tirer sur le cordon pour débrancher l'outil. Éloigner le cordon des sources
de chaleur, des flaques d'huile, des arêtes tranchantes et des pièces mobiles.
Remplacer immédiatement les cordons endommagés. Les cordons endommagés

augmentent les risques de secousses électriques.

• Lorsqu'on utilise un outil électrique à l'extérieur, se servir d'un cordon de rallonge

prévu pour l'extérieur, portant la mention «W-A» ou «W». Ces cordons sont conçus
pour servir à l'extérieur et minimisent les risques de secousses électriques. Lorsqu’on se
sert d’un cordon de rallonge, s’assurer qu’il est de calibre approprié pour la tension
nécessaire au fonctionnement de l’outil. L’utilisation d’un cordon de calibre inférieur
occasionne une baisse de tension entraînant une perte de puissance et la surchauffe. Le
tableau suivant indique le calibre approprié selon la longueur du cordon et les mentions de
la plaque signalétique de l’outil. En cas de doute, utiliser un cordon de calibre supérieur.
Le chiffre indiquant le calibre est inversement proportionnel au calibre du cordon.

SÉCURITÉ PERSONNELLE

• Demeurer vigilant, prendre soin et faire preuve de jugement lorsqu'on utilise un outil
électrique. Ne pas s'en servir lorsqu'on est fatigué ou affaibli par des drogues, de
l'alcool ou des médicaments. De graves blessures peuvent résulter d'un moment

d'inattention lors de l'utilisation d'un outil électrique.

• Porter des vêtements appropriés. Éviter de porter des vêtements amples ou des
bijoux. Recouvrir la chevelure si elle est longue. Éloigner les cheveux, les
vêtements et les gants des pièces en mouvement qui peuvent les happer.

• Éviter les démarrages accidentels. S'assurer que l'interrupteur est en position hors
tension avant de brancher l'outil. Afin d'éviter les risques de blessures, ne pas

transporter l'outil avec le doigt sur l'interrupteur ni brancher un outil dont l'interrupteur est en
position sous tension.

• Enlever les clés de réglage avant de mettre l'outil sous tension. Une clé qui est
laissée sur une pièce rotative de l'outil présente des risques de blessures.

• Ne pas dépasser sa portée. Garder son équilibre en tout temps. On s'assure d'une
meilleure maîtrise de l'outil dans des situations imprévues grâce à une position stable et un
bon équilibre.

• Porter de l'équipement de sécurité. Toujours porter des lunettes de sécurité. Dans
certaines conditions, il faut porter des masques respiratoires, des chaussures
antidérapantes, un casque de sécurité ou des protège-tympans.

UTILISATION ET ENTRETIEN DE L'OUTIL

• Utiliser des pinces de serrage ou de tout autre moyen pratique afin de fixer et de
soutenir la pièce à ouvrer sur une plate-forme stable. La pièce est instable lorsqu'elle

est retenue par la main ou le corps de l'utilisateur. Cela présente des risques de perte de
maîtrise de l'outil.

• Ne pas forcer l'outil. Utiliser l'outil approprié à la tâche. L'outil approprié fonctionne
mieux et sûrement lorsqu'on s'en sert à son rendement nominal.

• Ne pas se servir de l'outil lorsque l'interrupteur est défectueux. Le cas échéant, l'outil
est dangereux et il faut le réparer.

• Débrancher l'outil de la source d'alimentation avant de le régler, d'en remplacer les
accessoires ou de le ranger. On minimise de la sorte le risque de démarrage accidentel

de l'outil.

• Ranger l'outil hors de portée des enfants et de toute autre personne qui n'en connaît
pas le fonctionnement. L'outil est dangereux entre les mains de ces personnes.

• Prendre soin des outils. S'assurer que les outils de coupe sont tranchants et
propres. Des outils bien entretenus à arêtes tranchantes ont moins tendance à se coincer

et ils se maîtrisent mieux.

• Vérifier l'alignement et les attaches des pièces mobiles, le degré d'usure des pièces
ainsi que tout autre facteur susceptible de nuire au bon fonctionnement de l'outil.
Faire réparer un outil endommagé avant de s'en servir. Des outils mal entretenus sont

la cause de nombreux accidents.

• Utiliser seulement les accessoires recommandés par le fabricant. Des accessoires
qui conviennent à un outil peuvent présenter des risques avec un autre outil

ENTRETIEN

• Confier l'entretien de l'outil seulement à du personnel qualifié. Le non-respect de la
présente directive présente des risques de blessures.

• Lors de l'entretien de l'outil, utiliser seulement des pièces de rechange identiques.
Respecter les consignes relatives à l'entretien du présent guide d'utilisation. Il y a

risque de secousses électriques ou de blessures lorsqu'on utilise des pièces non
autorisées ou lorsqu'on ne respecte pas les consignes relatives à l'entretien.

L’étiquette de l’outil peut comporter les symboles suivants:

V ....................................volts A..........................ampères

Hz ..................................hertz W ........................watts

min..................................minutes ......................courant alternatif

................................courant continu

n

o........................sous vide

....................................

Construction de classe II

........................borne de mise à la

minute

..................................symbole d´avertissement .../min ..................tours ou courses

à la minute

MESURES DE SÉCURITÉ : DOUBLE ISOLATION

Les outils à double isolation comportent deux couches distinctes d’isolant électrique ou une
double épaisseur d’isolant qui protègent l’utilisateur contre les risques de blessures
provenant du système électrique de l’outil. Ce système de double isolation élimine le besoin
de mettre les outils à la terre. En effet, l’outil est muni d’une fiche à deux broches, ce qui
permet d’utiliser une rallonge ordinaire sans avoir à se soucier d’assurer la mise à la terre.

La double isolation ne dispense pas des mesures de sécurité normales lors de l’utilisation
de l’outil. Elle vise à procurer une protection supplémentaire contre les blessures que peut

CONSERVER LE PRÉSENT GUIDE À TITRE DE RÉFÉRENCE.

RENSEIGNEMENTS IMPORTANTS

• Ne jamais utiliser la ponceuse sans avoir au préalable installé le disque approprié
sur le tampon.

• On peut remplacer le tampon et le disque blanc du frein du tampon. En cas
d’usure, confier la réparation de l’outil au centre de service de la région.

• Ne pas exercer une pression excessive sur l’outil - laisser la ponceuse travailler
seule.

PPPPoooonnnncccceeeeuuuusssseeee ddddeeee ffffiiiinnnniiiittttiiiioooonnnn oooorrrrbbbbiiiittttaaaalllleeee eeeexxxxcccceeeennnnttttrrrriiiiqqqquuuuee

ee

ddddeeee 111122227777 mmmmmmmm ((((5555 ppppoooo))))

Modèle TV750

AVANT DE RETOURNER LE PRODUIT, PEU IMPORTE LA RAI-

SON PRIÈRE DE COMPOSER

1 800 544-6986

Calibre minimal des cordons de rallonge

Tension Longueur totale du cordon en pieds

120 V De 0 à 25 De 26 à 50 De 51 à 100 De 101 à 150
240 V De 0 à 50 De 51à 100 De 101 à 200 De 201 à 300

Intensité (A)
Au Au Calibre moyen de fil

moins plus

0-6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Non recommandé

AVERTISSEMENT : IMPORTANTES MESURES DE SÉCURITÉ

AVERTISSEMENT! Vous devez lire et comprendre toutes les instructions. Le non-

respect, même partiel, des instructions ci-après entraîne un risque de choc électrique, d’in­cendie et/ou de blessures graves.

CONSERVEZ CES INSTRUCTIONS.

ZONE DE TRAVAIL

• S'assurer que la zone de travail est propre et bien éclairée. Des établis encombrés et
des endroits sombres présentent des risques d'accidents.

• Ne pas utiliser des outils électriques en présence de vapeurs explosives (comme
celles dégagées par des liquides, des gaz ou des poussières inflammables). Les

étincelles générées par le moteur des outils électriques peuvent enflammer les poussières
ou les vapeurs.