Massive Audio Blade 1000.2 Instruction Manual

2

280 W

420 W

NA

1000 W

8Hz - 185Hz

>92 dB

16Hz - 139Hz

N/A

67 Kohm

85%

>100

0.2-5V

40A

0.6 A
2 Ohm

40

2.6x8.7x9
66 x 220 x 229

160 W

280 W

1

SPECIFICATIONS

1000

Blade 1000Blade

RMS @ 2 Ohm (<1% distortion)

RMS @ 4 Ohm (<1% distortion)

420 W

RMS @ 1 Ohm (<1% distortion)

1000 W

Maximum Power @ 14.4VDC

8Hz - 185Hz

Frequency Response @ -3 dB

>92 dB

16Hz - 139Hz

S/N Ratio ( A.Wtg )1Watt reff.

Frequency Response @ -1 dB

N/A

67 Kohm

Input Impedance

Bass Boost @ 45 Hz 12 dB

85%

>100

0.2-5V

Damping 100 Hz @ 4 Ohms

Input Sensitivity

0.6 A

Idle Current

Efficiency

40A

1 Ohm

Minimum Impendence

Max Peak Current

40

Required External Fuse

2.6x8.7x9
66 x 220 x 229

Dimensions (H x W x L) Inches

Dimensions (H x W x L) Metric(mm)

2006 Massive Audio Inc.

C

Printed in the U.S.A.

V.012006

1. Speaker connection

··Never connect the speaker cables with the chassis ground. This could destroy

your amplifier.
Check that your speakers are connected correctly which means plus to plus and minus
to minus.

2. BATT+

Battery + (plus) terminal. The + (plus) 12 Volt power cable must be connected with a fuse on the
battery + (plus) terminal. We recommend a 40 ampere fuse and a copper cable with a thickness of
gauge 8 for cable length up to 5 metres.

10. Low Pass Filter

To filter out the high frequency and only produce low frequency with 12dB filter to insure high
quality solid bass reproduction.

11. POWER-LED

Indicate the amplifier is switched on.

12. PROTECTION-LED

Indicate if the amplifier is in protection or other malfunction.

3. REM

Remote terminal. The remote cable must be connected with the radio remote output terminal so
that the amplifier will switch on and off automatically with the radio. If there are 2 or more
amplifiers connected to this antenna terminal it might be necessary to add an additional relay.
Please consult your dealer.

4. GND

Chassis ground-terminal. The chassis ground cable must be connected very tight on a
nearby massive and electric conductive place.

5. RCA audio-input

These RCA inputs are to be connected with your radio preamp RCA outputs. Please use
RCA cables made for car audio, otherwise there could be disturbances. Keep these cables
as short as possible. To avoid disturbances from your car electronics, install the RCA cables
not to close from existing car cables.

6. RCA Audio Output

These RCA outputs are to be connected with other amplifier inputs. This buffered output signal is easy to use
for daisy chain amplifier installation.

7. FUSE

To protect the amplifier when current is more than rated.
Never replace a fuse with a higher fuse.
Never replace a burnt fuse before checking the system for cause of the malfunction.

8. High Level input

High level input can receive a speaker level input signal if the CD player dose not have a RCA
output signal. Make sure this input will not be used when RCA input is active.

R

1000

1

-

9

+

10

11

12

9.GAIN

Gain control regulates the sensitivity of the amplifier to match the signal output voltage of the
source unit. The gain control is not intended for volume adjustment.
Use high quality CD music and increase the volume of your source unit to 75%.
Position the gain at minimum and then slowly increase Gain (clockwise).
Stop at the first sign of distortion, then lower the Gain a little (counter clockwise) to achieve clear
undistorted music at maximum level.

1

5

6

8

7

2

3

4