
Contents
1 List of applicable FCC rules ......................................................................................................................... 2
2 Summarize the specific operational use conditions .................................................................................. 2
3 Limited module procedures ....................................................................................................................... 2
4 Trace antenna designs ............................................................................................................................... 2
5 RF exposure considerations ....................................................................................................................... 2
6 Antennas .................................................................................................................................................... 2
7 Label and compliance information ............................................................................................................ 2
8 Information on test modes and additional testing requirements ............................................................. 3
9 Additional testing, Part 15 Subpart B disclaimer ....................................................................................... 3
1

1 List of applicable FCC rules
MWMII is tested to below:
47 CFR § FCC 15.247:2019 - Operation within the bands 902–928 MHz, 2400–2483.5 MHz,
and 5725–5850 MHz
47 CFR § FCC 15.407:2019 - General technical requirements
2 Summarize the specific operational use conditions
Below antennas are to be used with MWMII –
Ethertronics 9000129
Ethertronics 1000672
The radio module is intended for professional users.
3 Limited module procedures
Not applicable. MWMII module is certified as Single Modular Approval.
4 Trace antenna designs
Not applicable. MWMII uses external antennas please refer to section 6.
5 RF exposure considerations
MWMII module is intended for mobile application conditions.
6 Antennas
MWMII uses one of two (external) antennas: Ethertronics 9000129 and Ethertronics 1000672.
Ethertronics 9000129 uses an ultra-small u. Fl. connector with 100 mm long cable and Ethertronics
1000672 uses an ultra-small u. Fl. connector with 200 mm long cable.
7 Label and compliance information
Host product manufactures are required to provide physical or e-label stating “Contains FCC ID VKFMWM2” or equivalent with their finished product. For regulatory information to be provided, refer to
2

the FCC rules that apply to the host product. The label requirements for the RF device depends on the
type of the equipment authorization used. So provide regulatory information as appropriate.
8 Information on test modes and additional testing requirements
MWMII has been tested in standalone configuration for FCC compliance testing and thus the
simultaneous transmission conditions, if applicable, must be evaluated by the integrator. Evaluate
compliance for a host using certified modules and/or a stand-alone product requires: addressing EMC
requirements for composite system testing and for simultaneous transmission.
Host manufactures are required to perform testing for spurious emissions if only one module is installed
in the host.
Host manufactures are required to perform testing on the product with transmitter or transmitters
operating to confirm that the host product meets the FCC requirements. This investigation of the final
product can be done by spot checking emissions from the device while operating the host as a
composite system (with all the transmitters operating simultaneously). This testing is performed with
the host product configured in typical operational modes to check the fundamental-frequency and
spurious emissions for compliance with all the applicable rules. Masimo Corporation provides test
scripts which allow host to operate for FCC compliance testing.
In order to verify the continued FCC compliance, host manufacturers are required to consider test
modes for different operational conditions as well as for multiple simultaneous transmitting modules or
other transmitters, if any, in a host product. It is host product manufacture’s responsibility to evaluate
compliance.
In cases where host product is regulated under different or additional FCC rules, host product
manufacturers are required to perform verification testing to confirm that the end product complies
with all the accountable FCC compliance requirements.
9 Additional testing, Part 15 Subpart B disclaimer
Modular transmitter MWMII is FCC authorized for the rules specified on the grant and the host product
manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by
the modular transmitter grant of certification.
Host manufactures are required to obtain the equipment authorization of the applicable unintentional
radiator functions under part 15 subpart B of the host product, and if required any additional testing
and certification for any other included transmitters.
3