Marvel ML15WSP2LP User Manual

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien
ES Instrucciones de instalación, operación y mantenimiento

Wine Cellars
Celliers

Bodegas para vinos

Note: Wine Cellars are designed exclusively for the
storage of wine. Wine Cellars cannot attain storage
temperatures suitable for fresh food storage.

Remarque : Les celliers sont conçues exclusivement
pour y garder des vins. Elles ne peuvent pas atteindre des
températures de conservation convenant à l’entreposage
d’aliments frais.

ML15WS
ML24WS
ML24WD

Nota: Estas bodegas están diseñadas exclusivamente

para el almacenamiento de vino. Las bodegas para vinos
no pueden alcanzar las temperaturas adecuadas para el
almacenamiento de alimentos frescos.

CONTENTS

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti-tip device .................................................6

Product dimensions ............................................................8

Using your Electronic control ............................................10

Starting your appliance ..................................................10

Sleep mode ...................................................................10

Turning your appliance "ON" or "OFF" ..........................10

Adjusting the temperature .............................................11

Interior display lighting ...................................................11

Temperature mode ........................................................12

Control lock ....................................................................12

Alarms ...........................................................................12

Door ajar ..................................................................12

Power failure .............................................................12

Temperature alarm ....................................................12

Vacation mode ..............................................................13

Overlay door panel installation ........................................14

Shelving congurations ....................................................18

Care and cleaning .............................................................20

Energy saving tips ............................................................20

Door alignment .................................................................21

Obtaining service .............................................................21

Troubleshooting ................................................................22

Warranty ...........................................................................23

Important Safety Instructions

Warnings and safety instructions appearing in this guide
are not meant to cover all possible conditions and situa­tions that may occur. Common sense, caution, and care
must be exercised when installing, maintaining, or operat­ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

!

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

!

CAUTION

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE

NOTE-Important information to help assure a problem

free installation and operation.

State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals

known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals
known to the State of California to cause birth defects or
other reproductive harm..

is committed to building a quality product
in an environmentally friendly manner. Our processes are
tightly controlled and closely monitored. We have achieved

certications in ISO 9001 for quality assurance, ISO 14001
for environmental management, and OHSAS 18001 for oc-

cupational health and safety from Lloyd’s Register Quality
Assurance.

2

UNPACKING YOUR APPLIANCE

!

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts
that could be damaged by movement securely fastened.
Remove internal packing materials and any tape holding in­ternal components in place. The owners manual is shipped
inside the product in a plastic bag along with the warranty
registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has
been thoroughly inspected and found to be in good condi­tion. If there is damage, the packaging will be needed as
proof of damage in transit. Afterwards please dispose of all
items responsibly.

Warranty Registration

It is important you send in your warranty registration card
immediately after taking delivery of your appliance or you
can register online at www.agamarvel.com.

The following information will
be required when registering
your appliance.
Service Number
Serial Number
Date of Purchase
Dealer’s name and address

The service number and serial number can be found on the
serial plate which is located inside the cabinet on the left

side near the top. (See gure 1).

Online registration

available at

www.agamarvel.com

!

CAUTION

Dispose of the plastic bags which can be a suffocation
hazard.

Note to Customer

This merchandise was carefully packed and thoroughly
inspected before leaving our plant. Responsibility for its
safe delivery was assumed by the retailer upon acceptance
of the shipment. Claims for loss or damage sustained in
transit must be made to the retailer.

NOTE

DO NOT RETURN DAMAGED MERCHANDISE TO THE
MANUFACTURER - FILE THE CLAIM WITH THE
RETAILER.

!

CAUTION

If the appliance was shipped, handled, or stored in other
than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.
Plugging the appliance in immediately may cause damage
to internal parts.

XXXXXXXXXXXX

XXXXXXXXXXXX

Figure 1

!

CAUTION

Help Prevent Tragedies

Child entrapment and suffocation are not problems of the
past. Junked or abandoned refrigerators are still dangerous

- even if they sit out for "just a few days".

If you are getting rid of your old refrigerator, please follow
the instructions below to help prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not easily
climb inside.

3

INSTALLING YOUR APPLIANCE

Select Location

The proper location will ensure peak performance of your
appliance. We recommend a location where the unit will
be out of direct sunlight and away from heat sources. To
ensure your product performs to specications, the recom­mended installation location temperature range is from 55

to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli­ance. Keep this area open and clear of any obstructions.
Adjacent cabinets and counter top can be installed around
the appliance as long as the front grille remains unob­structed. Overlay door models with articulated hinges are
intended for built-in applications only.

!

WARNING

An optional stacking kit, shown in Table "A", is required
to stack products. Failure to use a stacking kit could
result in personal injury. Contact your dealer or Aga

Marvel customer service at 800-223-3900 to order.

Color Door Swing Kit Part Number

Stainless Steel Left Hand 42249095

Stainless Steel Right Hand 42249096

Black Left Hand 42249097

Black Right Hand 42249098

White Left Hand 42249099

White Right Hand 42249100

Front Grille,
keep this area
open.

Front Leveling
Legs

Figure 2

Rear

Leveling

Legs

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the
oor and level from side to side and front to back. The over-

all height of your Marvel appliance may be adjusted higher

(by turning the leveling leg out, CCW) and lower (by turning
the leveling leg in, CW) dimensions as shown in Table "B".

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid
scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.
Raise or lower the legs to the required dimension by turning
the legs. Repeat this process for the rear by tilting the appli­ance forward using caution. On a level surface check the
appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad­justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 3).

Table A

!

CAUTION

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex­changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason
it is important this area not be obstructed and the grille
openings kept clean. AGA MARVEL does not recommend

the use of a custom made grille as air ow may be restrict­ed. (See Figure 2).

Model Door Style

ML(15)(24)* (S) or (G)

ML(15)(24)* (P) or (F)

4

Table B

Minimum

Height

33 3⁄4"

(85.7 cm)

34"

(86.4 cm)

Maximum

Height

34 3⁄4"

(88.3 cm)

35"

(88.9 cm)

INSTALLING YOUR APPLIANCE

!

Electrical Shock Hazard

• Do not use an extension cord with this appliance.
They can be hazardous and can degrade product
performance.

• This appliance should not, under any circumstanc­es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power
cord.

• Do not use an adapter.

• Do not splash or spray water from a hose on the
appliance. Doing so may cause an electrical shock,
which may result in severe injury or death.

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

WARNING

Figure 3

Front grille

Front grille screw

This product is factory equipped with a power supply
cord that has a three-pronged, grounded plug. It must be
plugged into a mating grounding type receptacle in accor­dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 4). If the circuit does

not have a grounding type receptacle, it is the responsibility
and obligation of the customer to provide the proper power
supply. The third ground prong should not, under any cir­cumstances, be cut or removed.

Figure 4

NOTE

Ground Fault Circuit Interrupters (GFCI) are prone to nui­sance tripping which will cause the appliance to shut down.
GFCI’s are generally not used on circuits with power equip­ment that must run unattended for long periods of time, un­less required to meet local building codes and ordinances.

5

INSTALLING THE ANTI TIP DEVICE

!

WARNING

• ALL APPLIANCES CAN TIP
RESULTING IN INJURY.

Anti-Tip
Bracket

Leveling Leg

• INSTALL THE ANTI-TIP
BRACKET PACKED WITH
THE APPLIANCE.

• FOLLOW THE INSTRUC­TIONS BELOW

Anti-Tip Device

!

CAUTION

If your wine cellar is not located under a counter top (free

standing), you must use an anti-tip device installed as per

these instructions. If the wine cellar is removed from its lo­cation for any reason, make sure that the device is properly
engaged when you push the wine cellar back into the origi­nal location. If the device is not properly engaged, there is
a risk of the wine cellar tipping over, with the potential for
property damage or personal injury.

211⁄2"

(54.6 cm)

Bottom View of

Wine Cellar

Front of cabinet

Figure 5

Step by step instructions for locating the po­sition of the bracket:

1) Decide where you want to place the wine cellar. Slide it
into place, being careful not to damage the oor, leaving 1"
(2.5 cm) of clearance from the rear wall to allow room for

the anti-tip bracket.

2) Raise the rear leveling legs approximately 1⁄4" (6 mm) to

allow engagement with the anti-tip bracket. Level the unit
by adjusting all the leveling legs as required. Turning the
leveling leg counterclockwise will raise the unit and clock­wise will lower the unit.

NOTE

If installing on a concrete oor, concrete fasteners are
required, (not included with the anti-tip kit).

!

CAUTION

Any nished ooring should be protected with appropriate

material to avoid damage when moving the unit.

Floor Mount Installation

The anti-tip bracket is to be located on the oor in the left or

right rear corner of the wine cellar as shown in Figure 5.

3) Make sure the wine cellar is in the desired location, then
mark on the oor the rear and side corner of the cabinet

where the anti-tip bracket will be installed. If the installation
does not allow marking the rear corner of the cabinet, then

make temporary lines on the oor marking the front corner

of the cabinet, excluding the door. Slide the wine cellar out
of the way. From the temporary line extend the sidewall

line back 211⁄2" (54.6 cm) as shown in Figure 6.

4) Align the anti-tip bracket to the marks on the oor so

the side of the bracket lines up with the side of the cabinet
mark, and the "V" notches on the anti-tip bracket line up

with the end of the 211⁄2" (54.6 cm) line (Rear of cabinet
line).

5) Fasten the anti-tip bracket to the oor using the supplied
screw. (See Figure 6).

6) Slide the cabinet back into position, making sure the

rear cabinet leveling leg slides under the anti-tip bracket
engaging the slot.

6

INSTALLING THE ANTI TIP DEVICE

!

WARNING

TIP OVER HAZARD: One of the rear cabinet

leveling legs must be engaged under an anti-tip
bracket.

NOTE

When the oor mounted anti-tip bracket is used the mini­mum adjusted height of the cabinet is increased by

3

⁄8" (9 mm).

Front of cabinet line

Side of cabinet line

211⁄2"

(54.6 cm)

Figure 6

Rear Leveling leg

Rear of cabinet line

Screw

"V" notches
in bracket

Figure 6a

"V" notches
in bracket

7

PRODUCT DIMENSIONS

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

ML15WSG

ML15WS(P) or (F)

ML24W*G

ML24W*(P) or (F)

DOOR STYLE

(G) Glass Frame Door

(P) Solid Overlay Door (no handle)

(F) Frame Glass Overlay Door (no handle)

15"

(38.1 cm)

15"

(38.1 cm)

24"

(61 cm)

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

**341⁄4" to 351⁄4"
(87 to 89.5 cm)

**34" to 35"

(86.4 to 88.9 cm)

**341⁄4" to 351⁄4"
(87 to 89.5 cm)

*

*

*

*

147⁄8"

(37.8 cm)

147⁄8"

(37.8 cm)

237⁄8"

(60.7 cm)

237⁄8"

(60.7 cm)

333⁄4" to 343⁄4"

(85.7 to 88.3 cm)

34" to 35"

(86.4 to 88.9 cm)

333⁄4" to 343⁄4"

(85.7 to 88.3 cm)

34" to 35"

(86.4 to 88.9 cm)

2323⁄32"

(60.2 cm)

227⁄8"

(58.1 cm)

2323⁄32"

(60.2 cm)

227⁄8"

(58.1 cm)

2521⁄32"

(65.2 cm)

-

2521⁄32"

(65.2 cm)

-

3713⁄32"

(95 cm)

371⁄2"

(95.2 cm)

4613⁄32"

(117.9 cm)

461⁄2"

(118.1 cm)

1611⁄16"

(42.4 cm)

141⁄8"

35.9 cm)

2511⁄16"

(65.2 cm)

231⁄8"

(58.7 cm)

"C"

"A"

"B"

"E"

Figure 7

"D"

Figure 7a

If necessary to gain clearance inside
the rough-in opening a hole can be cut
through the adjacent cabinet and the
power cord routed through this hole to a
power outlet. Another way to increase the
available opening depth is to recess the

power outlet into the rear wall 1" (2.5 cm)

to gain the thickness of the power cord
plug.

8