Page 1
U-DS90W Creation Station
[1] Small Wrench [M]
[2] Castors [K]
[1] Large Wrench [L]
[2] Small Wood Screws [I]
[2] Locking Castors [J]
[4] Collars [G]
[4] Male Knobs [H]
[8] M4.2 x 16mm [E]
[8] M4.2 x 12mm [F]
[4] 1/4” x 35mm [C]
[8] 1/4” x 2-1/2” [D]
[8] M6 x 13mm [A]
[4] Nuts [B]
Assembly Instructions
Contents of Hardware Pack:
[1] Allen Wrench [N]
IMPORTANT
If you have difficulty assembling your U-DS90W
Creation Station or need customer service
assistance. Please call:
Martin Universal Design, Inc.
Customer Service Hot Line at
1-313-895-0700.
If you need additional parts,
it is not necessary to contact your dealer,
our Customer Service Rep. will forward them
to you immediately.
4444 Lawton Avenue, Detroit, MI 48208 USA • Tel:(313)895-0700/Fax:(313)895-0709
Email: Custservmud@aol.com • visit us at www.MartinUniversalDesign.com
List of Hardware:
Qty Part Description Part Number
[8] M6 x 35mm [A]
[4] Nuts [B]
[4] 1/4” x 35mm [C]
[8] 1/4” x 2-1/2” [D]
[8] M4.2 x 16mm [E]
[8] M4.2 x 12mm [F]
[4] Collars [G]
[4] Male Knobs [H]
[2] Small Wood Screws [I]
[2] Locking Castors [J]
[2] Castors [K]
[1] Large Wrench [L]
[1] Small Wrench [M]
[1] Allen Wrench [N]
Revised June 07- RPI
Page 2
U-DS90W Creation Station
[1 ea.] Pencil Edge [9]
[4 ea.] Drawer Supports
[10]
[1 ea.] Upper Base End
Unit (left) [3]
[1 ea.] 24” x 40” Top [1]
[2 ea.] Lower base End
Unit [2]
[1 ea.] Upper Base End
Unit (right) [4]
[1 ea.] Base Cross Support
Bar [5]
[1 ea.] Foot Bar
[7]
[1 ea.] Top Surface Cross
Support [6]
[2 ea.] Tilt Support
Mechanisms [8]
[2 ea.] L Bracket Top
Supports [11]
[2 ea.] Drawer Bank of 3
[12]
Assembly Instructions
Parts List:
IMPORTANT
If you have difficulty assembling your U-DS90W
Creation Station or need customer service
assistance. Please call:
Martin Universal Design, Inc.
Customer Service Hot Line at
1-313-895-0700.
If you need additional parts,
it is not necessary to contact your dealer,
our Customer Service Rep. will forward them
to you immediately.
4444 Lawton Avenue, Detroit, MI 48208 USA • Tel:(313)895-0700/Fax:(313)895-0709
Email: Custservmud@aol.com • visit us at www.MartinUniversalDesign.com
List of Parts:
Qty Part Description Part Number
[1] 20” x 40” White Top [1]
[2] Lower Base End Unit [2]
[1] Upper Base End Unit (left) [3]
[1] Upper Base End Unit (right) [4]
[1] Base Cross Support Bar [5]
[1] Top Surface Cross Support [6]
[1] Foot Bar [7]
[2] Tilt Support Mechanisms [8]
[1] Pencil Edge [9]
[4] Drawer Supports [10]
[2] L-Bracket Top Supports [11]
[2] Drawer Units (3 drawers each) [12]
Revised June 07- RPI
Page 3
Assembly Instructions:
STEP 1] Assembly Base of table
Begin by taking the [2] Lower Base End units (part #2 and
attach the foot bar (part # 7) and the Base Cross Support bar
(part# 5) to each base end using the 1/4” x 2-1/2” Allen Bolts
(part# D). Secure with Allen Wrench (part N), See FIG 1.
Once the base is assembled continue by adding the [4]
collars (part G) to the ends of the base, as pictured below.
Complete Step 1 by inserting [2] locking castors (part J)
into the front of the base end. Complete by inserting the [2]
remaining castors into the rear of the base.
See picture below.
G
D
5
K
7
G
D
D
2
J
STEP 3] Complete Base Assembly
Take the top portion and the lower portion of the base that
was just assembled. Insert the top portion into the lower por
tion, making sure the top ends slide into the collars that are
on the lower portion of the base. Secure with the [4] male
knobs (part H) tightening them into the collars. As shown
below in FIG 3.
G
H
H
G
-
K
D
2
FIG 1
J
STEP 2] Assemble upper portion of base
Take each upper Base end (left - part #3) and (right - part #4)
and attach to Top Surface Cross Support (part #6) using [2]
1/4” x 2-1/2” Allen bolts (part D). Secure with Allen Wrench
See FIG 2.
4
D
FIG 2
3
6
FIG 3
STEP 4] Drawer Support Assembly
Attach [2] Drawer Supports (part #10) to each set of drawers (part #12) by sliding one onto each end of the drawers
making sure the hooked end is positioned as pictured below
and the 2 holes are on the bottom side of the drawer unit.
Secure each support using [2] M4.2 x 12mm (part F) in each
support. [4] total for each drawer unit. See FIG 4.
10
12
Hooked bent end
D
Pg. 3
F
F
FIG 4
Revised June 07- RPI
Page 4
Assembly Instructions:
STEP 5] Attach Drawer Units to Base
Attach the drawer units to the table base as illustrated below
using [4] M4.2 x 16mm screws (part E) for each drawer unit.
See FIG 5 below.
5
5
5
12
5
12
FIG 5
STEP 7] Attach L-Bracket to Base
Take the L-Bracket (part #11) and insert the pin that is attached to the L-Bracket into the hole on the inside section of
the upper base end. Repeat with other side.
NOTE: This L-bracket has two holes which are used to
attach to the bottom of the top with [2] Allen M6 x 13mm
bolts per L-bracket. See Step 9.
11
STEP 8] Attaching Tilt Supports to Top
Attach the [2] Tilt Supports (part #8) to the Top (part #1) us
ing [2] M6 x 13mm Allen Bolts (part A) into the T-Nuts found
on the underside of the Table Top (part #1). Tighten with
Allen Wrench. NOTE: This step is easier if you place the
assembled base upside down onto the table top on a
carpeted surface. Have [2] people help lifting and turn
the base upside down.
-
STEP 6] Attaching Tilt Supports to base
Attach the [2] Tilt Supports (part #8) to the Top Surface Cross
Support (part #6) using [2] M6 x 13mm Allen Bolts (part A) in
the upper portion of the tilt support and [2] 1/4” x 35mm Allen
bolts (part C) and secure with [2] nuts (part B). SEE FIG 6.
8
C
C
FIG 6
6
B
8
C
C
STEP 9] Attach L-Bracket to Top
Complete Top assembly by attaching L-Brackets to Top using
[2] M6 x 13mm Allen Bolts and securing them into T-Nuts
found on the underside of Top. Tighten with Allen Wrench.
Turn table back onto
its castors for use.
Lift up on back edge
of top to tilt surface.
4444 Lawton Avenue, Detroit, MI 48208 USA • Tel:(313)895-0700/Fax:(313)895-0709
Revised June 07- RPI
Email: Custservmud@aol.com • visit us at www.MartinUniversalDesign.com
Pg. 4
Loading...