Martin Universal Design U-DS24 User Manual

BERKELEY MAXUM U-DS24 ASSEMBLY

ITEM# PARTS LIST QTY
97-DS240A Stand Frame 1
97-DS240B Metal Guide 2
97-DS240C Plastic Knob 4
97-DS240D Hex Bolt 4
97-DS240E Phillips Screw 14

A. Stand Frame

D. Hex Bolt E. Phillips Screw

Y our new Berkeley MAXUM T able has been designed and manufactured to enhance your productivity and ef ficiency . This sturdy
folding table, properly assembled, will last through years of use. Follow the instructions below to assemble your Berkeley
Maxum and refer to the enclosed parts list for part identification. Tools needed for assembly: screwdriver, hammer , nail or awl,
tape measure and pencil. NOTE: Att aching T op instructions on reverse side of this sheet.

B. Metal Guide

C. Plastic Knob

Fig. 1

Brackets/Hinges

1. Swing the left and right side legs out
as shown. See Fig. 1

Any Questions with Assembly? We Can Help

PLEASE DO NOT RETURN THIS TABLE to the

Store where you purchased it. If you are

STO P

This Martin Universal Design, Inc. product has a one year guarantee to
be free from manufacturers defects during that period of use by the
original purchaser. Items or parts subjected to extreme temperature or
abuse or use of this product other than manufacturers intended purpose
is not covered under this guarantee.

Martin Universal Design, Inc. • 4444 Lawton Avenue, Detroit, MI 48208 USA

Tel: [phone] / Fax:[phone] • E-mail: [e-mail]

unable to assemble or parts are missing,

PLEASE Call Customer Service at

Martin Universal Design, Inc.

313-895-0700 or Email: [e-mail]

ONE YEAR GUARANTEE

Fig. 2

Fig. 3

NOTE:
Make sure the collar is in
the correct position as
shown. See Fig. 3

2. Put the hex bolt [D] inside the clamp (See Fig. 2)
and then attach knob [C] and tighten. (See Fig. 3)

3. Attach top to base. (Instructions on reverse side
of this sheet)

4. Once top is attached to base, to Adjust height of
table, loosen knobs on both rear collars, lift top
to chosen height/tilt. Tighten knobs to secure.
Continue by loosening front knobs on collars
and raise legs until desired front edge
height. Tighten knobs to secure.

BERKELEY MAXUM TOP ASSEMBLY

Determine which size top you have and follow the appropriate instructions

Instructions for 36” x 48” T op

Step [5] 3.75” from back edge

Bracket

Step [3]

1.5” from
left edge

Step [2] 1.5” from left side
to left edge of Metal Guide

Step [3]

1.5” from
right edge

Step [2] 1.5” from right side

to right edge of Metal Guide

Metal

Guide

Step [4] 3.75” from front edge

Step 1. Place top onto carpeted floor.
Step 2. Attach Left and Right Metal Guides by: Measuring 1.5” in

Step 3. Attaching Left and Right Brackets (already attached to

Step 4. Measure 3.75” from front edge and make pencil mark.
Step 5. Measure 3.75” from rear edge and make pencil mark.
Step 6. Position left and right Metal guides per above specs and

Step 7. Position left and right brackets per above specs and Attach

from left edge and mark with pencil, repeat with right side.
See above illustration.

base) by: Measuring 1.5” in from left edge and mark with
pencil, repeat with right side. See above illustration.

Repeat with other side for Metal Guides.
Repeat with other side for Brackets.
Attach with [3] phillips screws per guide.

Please Note: You may have to break top surface by
tapping a nail or awl in screw holes to make
starting hole in surface before attaching screws.

with [4] phillips screws per bracket.

Please Note: You may have to break top surface by
tapping a nail or awl in screw holes to make
starting hole in surface before attaching screws

Bracket

Metal
Guide

Instructions for 31.5” x 55” T o p

Bracket

Step [5] 1.5” from back edge

Step [3]

5” from
left edge

Step [2] 5” from left side
to left edge of Metal Guide

Step [3]

5” from
right edge

Step [2] 5” from right side to

right edge of Metal Guide

Metal

Guide

Step [4] 1.5” from front edge

Step 1. Place top onto carpeted floor.
Step 2. Attach Left and Right Metal Guides by: Measuring 1.5” in

Step 3. Attaching Left and Right Brackets (already attached to

Step 4. Measure 5” from front edge and make pencil mark.
Step 5. Measure 5” from rear edge and make pencil mark.
Step 6. Position left and right Metal guides per above specs and

Step 7. Position left and right brackets per above specs and Attach

from left edge and mark with pencil, repeat with right side.
See above illustration.

base) by: Measuring 1.5” in from left edge and mark with
pencil, repeat with right side. See above illustration.

Repeat with other side for Metal Guides.
Repeat with other side for Brackets.
Attach with [3] phillips screws per guide.

Please Note: You may have to break top surface by
tapping a nail or awl in screw holes to make
starting hole in surface before attaching screws.

with [4] phillips screws per bracket.

Please Note: You may have to break top surface by
tapping a nail or awl in screw holes to make
starting hole in surface before attaching screws

Bracket

Metal
Guide

Instructions for 37.5” x 48” T o p

Step [5] 4.5” from back edge

Bracket

Step [3]

1.5” from
left edge

Step [2] 1.5” from left side
to left edge of Metal Guide

Step [3]

1.5” from
right edge

Step [2] 1.5” from right side

to right edge of Metal Guide

Metal

Guide

Step [4] 4.5” from front edge

Step 1. Place top onto carpeted floor.
Step 2. Attach Left and Right Metal Guides by: Measuring 1.5” in

Step 3. Attaching Left and Right Brackets (already attached to

Step 4. Measure 4.5” from front edge and make pencil mark.
Repeat with other side for Metal Guides.
Step 5. Measure 4.5” from rear edge and make pencil mark.
Repeat with other side for Brackets.
Step 6. Position left and right Metal guides per above specs and

Step 7. Position left and right brackets per above specs and Attach

from left edge and mark with pencil, repeat with right side.
See above illustration.

base) by: Measuring 1.5” in from left edge and mark with
pencil, repeat with right side. See above illustration.

Attach with [3] phillips screws per guide.

Please Note: You may have to break top surface by
tapping a nail or awl in screw holes to make
starting hole in surface before attaching screws.

with [4] phillips screws per bracket.

Please Note: You may have to break top surface by
tapping a nail or awl in screw holes to make
starting hole in surface before attaching screws

Martin Universal Design, Inc. • 4444 Lawton Avenue, Detroit, MI 48208 USA • Tel: [phone] / Fax:[phone] • E-mail: [e-mail]

Bracket

Metal
Guide

Instructions for 37.5” x 60” T o p

Step [5] 4.5” from back edge

Bracket

Step [3]

7.5” from
left edge

Step [2] 7.5” from left side
to left edge of Metal Guide

Metal

Guide

Step [4] 4.5” from front edge

Step 1. Place top onto carpeted floor.
Step 2. Attach Left and Right Metal Guides by: Measuring 1.5” in

Step 3. Attaching Left and Right Brackets (already attached to

Step 4. Measure 3.75” from front edge and make pencil mark.
Step 5. Measure 3.75” from rear edge and make pencil mark.
Step 6. Position left and right Metal guides per above specs and

Step 7. Position left and right brackets per above specs and Attach

from left edge and mark with pencil, repeat with right side.
See above illustration.

base) by: Measuring 1.5” in from left edge and mark with
pencil, repeat with right side. See above illustration.

Repeat with other side for Metal Guides.
Repeat with other side for Brackets.
Attach with [3] phillips screws per guide.

Please Note: You may have to break top surface by
tapping a nail or awl in screw holes to make
starting hole in surface before attaching screws.

with [4] phillips screws per bracket.

Please Note: You may have to break top surface by
tapping a nail or awl in screw holes to make
starting hole in surface before attaching screws

Step [3]

7.5” from
right edge

Step [2] 7.5” from right side

to right edge of Metal Guide

Bracket

Metal
Guide