Martin Professional CYCLO 02, CYCLO 04, CYCLO 03 User Manual

martinarchitectural

l

Cyclo

user manua

Measurements are in millimeters

Cyclo 03

Cyclo 02

Cyclo 04

63

Cyclo 02

1190

88

Cyclo 03

81

1000

88

Cyclo 04

All rights reserved. No part of this manual may be reproduced, in any form or by an y means , with-

out permission in writing from Martin Professional A/S, Denmark.

98

88

© 2002 Martin Professional A/S, Denmark.

Printed in Denmark.

P/N 35000124, Rev C

I

NTRODUCTION

Thank you for selecting the Martin Cyclo. The Cyclo Series is a range of
controllable, fluorescent color changers. These fixtures are designed to be
used for cove lighting, perimeter lighting, light walls, behind semi­transparent materials, or any place where room is restricted.

Cyclo is a family of fixtures based on dimmable fluorescent T5 tubes. The
T5 tubes have achiev ed widespread popularity due to their sleek design and
high efficacy combined with their long lamp life.

In order to be DMX controlled, the Cyclo fixtures require the Martin 516
DMX to 0-10 V Converter. The 516 Conver ter converts DMX to 0-10 V
analog output. Additional Cyclos can be daisy-chained for synchronous
dimming. A single 516 Controller can control 4-8 Cyclo groups individually,
each group consisting of one to ten of the same Cyclo model wired in series
(the number of groups depends on the model of Cyclo that is installed). The
member fixtures in each group will react similarly when controlled.

Cyclo control and power-cables are through-wired for easy installation.
The Cyclo series offers:

• Controllable RGB color-mixing and/or color temperature

• Bright output

• Long lamp life of 20,000 hours

Note: It is important to read this manual through before you attempt

to install this product.

Cyclo fixtures

CYCLO 02

Cyclo 02 contains a single warm white tube and a single cold white tube.
It is designed as a functional lighting fixture for applications where dimmable

color temperature control ranging from 2700K up to 6000K are desirable.

CYCLO 03

Cyclo 03 contains dimmable red, green and blue tubes and is a cost efficient
RGB solution.

Cyclo user manual

3

CYCLO 04

Cyclo 04 contains dimmable red, green, blue and white tubes, and provides
a wider color range.

SAFETY INFORMATION

Warning! This product is for professi onal use only. It is not for household

use.

These products present risks of lethal or severe injury due to fire and heat,
electric shock and falls. Read this manual before powering or installing
these fixtures, follow the safety precautions listed below and observe all
warnings in this manual and on the fixtures. If you have questions about how
to operate these fixtures safely, please contact your Martin dealer or call the
Martin 24-hour service hotline at [phone].

Protection from electric shock

• Disconnect the fixtures from AC power before removing or installing a lamp,
fuses, or any part, and when not in use.

• Always ground (earth) the fixtures electrically.

• Use only a source of AC power that complies with local building and
electrical codes and has both overload and ground-fault protection.

• Do not expose the fixtures to rain or moisture.

• Refer all service to a Martin service technician.

Protection from burns and fire

• Provide a minimum clearance of 0.1 meters (4 inches) around the fixture.

• Do not modify the fixture or install other than genuine Martin parts.

• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C
(104° F).

Protection from injury due to falls

• Verify that all external covers and rigging hardware are securely fastened

• Block access below the work area wheneve r installing or removing the
fixture.

4

Cyclo user manual

I

NSTALLATION

This section describes in general terms how to install the fixture and
connect it to AC and dimmer power. These procedures shall be performed
by qualified professionals.

Mains

200-250V AC

50/60 Hz

516

DMX control device

Open the fixture:

1 Remove the fixture’s clear plastic

cover using a 2.5 mm Allen wrench.

2 Carefully remove each of the tubes by

rotating them (at the ends) until you
are able to pull one end out, and then
remove the entire tube.

DMX-to-analog (10V) converter

3 Using a Phillips screwdriver, loosen the two screws holding the cover of the

wiring housing in place; remove the cover.

Cyclo user manual

5

To ensure adequate ventilation, we
recommend that the Cyclo be installed with a
minimum of 25 mm (1 inch) of free space on
each side. Screw the fixture into place using,
either:

• 2 x 10 mm hardware together with the
supplied washers, separated by 1 metre (3.3
feet), or

• 4 x 8 mm hardware, in a matrix 1 metre by

6.5 cm square
Connect the AC power and dimmer control wiring (as described in the

following sections) before replacing the wiring-housing cover, the tubes, and
the clear plastic cover.

Ø8

Ø10

Ø8

AC POWER

Maximum power usage data for the three Cyclo models in supplied in
“Specifications - Cyclo 02” on page 11.

You can power Cyclo fixtures by wiring them in series. The internal wiring of
the fixtures carries AC power through the fixture. Holes are supplied at both
ends for input and output cables.

Warning: In the Cyclo series fixtures incorporate a single electronic

ballast per tube. Each of these “leaks” around 0,2 til 1 mA of
power. Because of this we recommend connecting a maximum
of 30 electronic ballasts (or tubes) per phase on a 30mA HPFI
circuit breaker.

A normal 30 mA HPFI circuit breaker normally trips because of a
current fault or leakage of approximately 20mA. It is important
that the installation is carried out correctly in order to avoid
unintentional tripping of the circuit breaker.

Many installations use common neutral leads in branch circuit
distribution boxes. It i s important that the neutral lead in the
cable is connected to the same HPFI circuit breaker, that it is
not connected to the neutral leads from other HPFI circuit
breakers. The neutral lead must be only associated with that
specific circuit breaker. Additionally it is important that the
fixtures are connected correctly to the ground (earth) to ensure
that the power leakage is able to run off.

6

Cyclo user manual

The cable for AC power is passed
through one of the two 5 mm holes
at the end of the fixture. These are
sealed with plastic an d you will
need to break a hole in one of the
them.

A clamp connector can be found at
each end of the fixture. One is used
to supply power and dimmer control
to the fixture and the other is used
to send power and dimmer control
onwards to other fixtures in a series.
The number of terminals present on
each clamp connector is dependent
on the Cyclo model.

Use the three terminals not shaded
in grey to connect A C power - L live,
or positive), N (neutral) and ground (or earth).

1

2

L

N

4

3

AC power

connections

Be sure to refer and comply with local standards. Some common AC cable
configuratio ns are:

Wire (EU) Wire (US) Pin Marking

brown black live “L”

blue white neutral “N”

yellow/green green ground

If the fixture is being wired in series with other Cyclo fixtures of the same
type, perform these steps at the other end of the fixture to connect it to the
next fixture.

Cyclo user manual

7

DIMMER CONTROL FROM A 516-II DMX

TO 0-10 V CONVERTER

Note: If you apply power to a Cyclo fixture that is not connected to a

dimmer then it will operate at full power.

The 516-II DMX to 0-10 V Converter has 16 analog outputs for connecting
0-10 V analog devices. For independent control, a Cyclo 02 requires two of
these outputs (one per ballast), a Cyclo 03 requires three outputs, and a
Cyclo 04 requires four outputs.

A maximum of 10 Cyclos (ballasts) of the same model can be wired in
series to the same analog output/s on the 516-II DMX to 0-10 V Conver ter.
Each Cyclo in the series will mimic the behavior of the others. Do not wire
different Cyclo models in series to the same analog outputs.

This means that a single 516-II DMX to 0-10 V Converter can provide
independent control of up to 8 groups of 10 Cyclo 02s (80 fixtures), 5 groups
of 10 Cyclo 03s (50 fixtures), 4 groups of 10 Cyclo 04s (40 fixtures), or a
combination of groups of up to 10 of each model.

Each output on the 516-II DMX to 0-10 V Converter is connected to both a
5-pin DIN socket and the 25-pin D-SUB socket. For the purposes of wiring,
the pin configuration can be found on the rear panel of the 516 controller.

Wiring the 5-pin DIN connector

Use a 5-pin DIN connector to connect the controller to a
series of one of more Cyclos of the same type. (The
controller has 4 5-pin DIN outputs enabling control of up
to four parallel series of Cyclo fixtures.)

Always connect the ground wire to pin 2, and control
leads to the other pins (between 2-4 depending on the
number of tubes in the Cyclo that is being connected). The pin number of
each output is shown on the rear panel. Make a note of which colored leads
are connected to which channels as well as which colored wire is the ground
wire.

Note: Connections can be tested without a controller by setting all

pins on the converter’s DIP-switch to the off position and then
applying power to the conver ter and the devices.

3

5

4

2

1

8

Cyclo user manual

Connecting the dimmer control cable to a Cyclo
fixture

The cable for dimmer control is
passed through one of the two 5
mm holes at the end of the fixture.
These are sealed with pla stic and
you will need to break a hole in one
of the them.

A clamp connector can be found at
each end of the fixture. One is used
to supply power and dimmer control
to the fixture and the other is used
to send power and dimmer control
onwards to other fixtures in a series.
The number of terminals present on
each clamp connector is dependent
on the Cyclo model.

2

Use the numbered terminals to
connect dimmer control. (Note that
there are fewer connectors on Cyclo models with fewer than four tubes.)
Connect the ground (earth) lead to the - terminal. Connect the other leads to
the appropriate connectors. Notes that there are two connectors at each
position and that you can use either one of these.

1

4

3

Dimmer

connectors

L

N

The internal wir ing in the fixture carries the di mmer control through the
fixture. Holes are supplied at both ends for input and output cables. If the
fixture is being wired in ser ies with other Cyclo fixtures of th e same type,
perform these steps at the other end of the fixture to connect dimmer control
to the next fixture.

Note: You can simultaneously control dimming on multiple Cyclo

fixtures of the same type by wiring them in series. However,
each analog output from the 516 Converter supplies 20mA. This
means that a maximum of 10 Cyclos (ballasts) in series can be
controlled from each 516 Converter channel. Each ballast
requires 1.5-2 mA.

If you are connecting multiple Cyclo fixtures in series that the
length and diameter of the control (dimmer) cabling must be
dimensioned so that the voltage drop over the cabling is less
than 0.5 volts.

Cyclo user manual

9

FLUORESCENT TUBES

Burning in new tubes

In order to obtain the full 200 00 hour life time, new fluorescent tubes must
be burned in for 100 hundred hours at full power (10 volts).

Identifying tube positions

Tube positions are identified in the Cyclo 03 and Cyclo 04 as follows:

Marking in fixture Marking on tube Color Reference illustration

R OSRAM 28/60 Red
G OSRAM 28/66 Green
B OSRAM 28/67 Blue

2700K white
4000K white
6000K white

None

OSRAM 28/827
OSRAM 28/840
OSRAM 28/860

CLEANING

We recommend that you clean the dust cover with a damp cloth.

B

G

R

S

PECIFICATIONS

PHYSICAL

L x W x H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1190 x 63 x 88 mm (50.1 x 2.7 x 3.7 in)

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.8 kg (8.4 lbs)

Shipping dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 1210 x 115 x 95 mm, (51 x 4.8 x 4 in)

Shipping weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.1 kg (9.1 lbs)

Fixture color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . white (NCS 0402-G06-Y)

INSTALLATION

Orientation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .any

Minimum free space around fixture when installed . . . . . . . . . . . . . . . . . . . 25 mm (1 inch)

SOURCE

Approved lamp type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .OSRAM T5 FH 28 watt tubes

Light source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T5 tubes (2x28W)

Expected lamp life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20000 hours

POWER

AC power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .198V-254V,50/60hz

Dimmer control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , 1-10V control

Maximum power and current @ 230 V / 50 Hz . . . . . . . . . . . . . . . . . . . . . 0.28 A / 64 watts

- C

YCLO

02

THERMAL

Maximum ambient temperature (Ta). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40° C (104° F)

DYNAMIC EFFECTS

Color temperature control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2700K up to 6000K

Independent dimming of each tube via 516 Converter

CONTROL (VIA 516 CONVERTER)

Number of independently controllable dimming channels . . . . . . . . . . . . . . . . . . . . . . . . .16

Channels required per independently controlled Cyclo 02 group . . . . . . . . . . . . . . . . . . . . .2

Channels required per independently controlled Cyclo 03 group . . . . . . . . . . . . . . . . . . . . .3

Channels required per independently controlled Cyclo 04 group . . . . . . . . . . . . . . . . . . . . .4

Number of Cyclos per group (fixtures wired in series). . . . . . . . . .1-10 (of the same model)

ORDERING INFORMATION

Cyclo 02. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90550020

INCLUDED ITEMS

Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .OSRAM T5 FH28W/827 (2700K) (white)

Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .OSRAM T5 FH28W/860 (6000K) (white)

User manual

ACCESSORIES

Martin 516 II DMX to 0-10V Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90758225

S

PECIFICATIONS

PHYSICAL

L x W x H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1190 x 81 x 88 mm (50.1 x 3.4 x 3.7 in)

Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7 kg (10.4 lbs)

Shipping dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 1210 x 115 x 95 mm, (51 x 4.8 x 4 in)

Shipping weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 kg (11 lbs)

Fixture color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . white (NCS 0402-G06-Y)

INSTALLATION

Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . any

Minimum free space around fixture when installed. . . . . . . . . . . . . . . . . . . . 25 mm (1 inch)

SOURCE

Approved lamp type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OSRAM T5 FH 28 watt tubes

Light source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T5 tubes (3x28W)

Expected lamp life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20000 hours

POWER

AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .198 V - 254 V, 50 / 60 Hz

Dimmer control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , 1-10V control

Maximum power and current @ 230 V / 50 Hz. . . . . . . . . . . . . . . . . . . . . .0.42 A / 96 watts

- C

YCLO

03

THERMAL

Maximum ambient temperature (Ta) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40° C (104° F)

DYNAMIC EFFECTS

Dimmable tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Red, green and blue

Independent dimming of each tube via 516 Converter

CONTROL (VIA 516 CONVERTER)

Number of independently controllable dimming channels . . . . . . . . . . . . . . . . . . . . . . . . 16

Channels required per independently controlled Cyclo 02 group . . . . . . . . . . . . . . . . . . . . 2

Channels required per independently controlled Cyclo 03 group . . . . . . . . . . . . . . . . . . . . 3

Channels required per independently controlled Cyclo 04 group . . . . . . . . . . . . . . . . . . . . 4

Number of Cyclos per group (fixtures wired in series) . . . . . . . . . 1-10 (of the same model)

ORDERING INFORMATION

Cyclo 03 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P/N 90550010

INCLUDED ITEMS

Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .OSRAM T5 FH28W/60 (red)

Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OSRAM T5 FH 28W/66 (green)

Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .OSRAM T5 FH28W/67 (blue)

User manual

ACCESSORIES

Martin 516 II DMX to 0-10V Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90758225

S

PECIFICATIONS

PHYSICAL

L x W x H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1190 x 98 x 88 mm (50 x 4 x 3.7 in)

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.5 kg (12.1 lbs)

Shipping dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 1210 x 115 x 95 mm, (51 x 4.8 x 4 in)

Shipping weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.9 kg (13 lbs)

Fixture color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . white (NCS 0402-G06-Y)

INSTALLATION

Orientation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .any

Minimum free space around fixture when installed . . . . . . . . . . . . . . . . . . . 25 mm (1 inch)

SOURCE

Approved lamp type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .OSRAM T5 FH 28 watt tubes

Light source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T5 tubes (3x28W)

Expected lamp life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20000 hours

POWER

AC power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 V - 254 V, 50 / 60 Hz

Dimmer control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , 1-10V control

Maximum power and current @ 230 V / 50 Hz . . . . . . . . . . . . . . . . . . . . 0.56 A / 128 watts

- C

YCLO

04

THERMAL

Maximum ambient temperature (Ta). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40° C (104° F)

DYNAMIC EFFECTS

Dimmable tubes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Red, green, blue and white

Independent dimming of each tube via 516 Converter

CONTROL (VIA 516 CONVERTER)

Number of independently controllable dimming channels . . . . . . . . . . . . . . . . . . . . . . . . .16

Channels required per independently controlled Cyclo 02 group . . . . . . . . . . . . . . . . . . . . .2

Channels required per independently controlled Cyclo 03 group . . . . . . . . . . . . . . . . . . . . .3

Channels required per independently controlled Cyclo 04 group . . . . . . . . . . . . . . . . . . . . .4

Number of Cyclos per group (fixtures wired in series). . . . . . . . . .1-10 (of the same model)

ORDERING INFORMATION

Cyclo 04. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90550000

INCLUDED ITEMS

Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OSRAM T5 FH28W/60 (red)

Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .OSRAM T5 FH 28W/66 (green)

Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OSRAM T5 FH28W/67 (blue)

Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OSRAM T5 FH28W/840 (white)

User manual

ACCESSORIES

Martin 516 II DMX to 0-10V Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P/N 90758225

www.martin-architectural.com • Olof Palmes Allé 18 • 8200 Aarhus N • Denmark

Tel: [phone] •

Fax [phone]