QUICK START GUIDE
QUICK START GUIDE
ADORN Series Quick Start Guide
Models covered in this quick-start guide:
ADORN A40, ADORN A40T, ADORN A55, ADORN A55T
Thank you for choosing Martin Audio’s ADORN Series. If you would like further information about this or any other Martin Audio product,
please visit our website www.martin-audio.com.
Unpacking
Every Martin Audio loudspeaker is built to the highest standard and thoroughly inspected before it leaves the factory. After unpacking the
system, examine it carefully for any signs of transit damage and inform your dealer if any is found. It is suggested that you keep the original
packaging so that the system can be repacked at a future date if necessary.
System Requirements
Low Impedance Systems
The ADORN A40 and A55 are designed to be used in a low impedance system. The A40T and A55T can also be used in a low impedance
system by selecting the 16W position on the selector switch on the back of the speaker. A conventional power amplifier or mixer-amplifier
designed for use with low impedance loads must be used. We recommend an amplifier that can deliver the full peak power rating without
risk of clipping to ensure the best possible performance and to avoid damage. The Martin Audio VIA amplifier range are a good match for
the ADORN Series. Performance can be further maintained by using a good quality system processor in particular to introduce a system
protection limiter. The Martin Audio DX0.5 is recommended for use with the ADORN Series.
70/100V Line Systems
The ADORN A40T and A55T can be used in a 70 or 100V line system. An amplifier designed for driving distributed line system must be
used. The appropriate tap must be selected using the rotary switch on the back of the speaker.
Ensure that the sum of all speaker taps does not exceed the amplifier’s rated power output.
Adding Subwoofers
For full range music systems, a subwoofer may be added. We would recommend a speaker from the Martin Audio SX Series such as the
SX110 which is a very compact single 10” subwoofer. This must be driven by another amplifier, for small low impedance systems the
four channel VIA Series amplifiers VIA2504 or VIA5004 are an excellent option. A system controller will be required to act as a crossover
between the subwoofer and ADORN speakers. The DX0.5 is the recommended processor.
Connections
Connections are made to all ADORN Series speakers using simple spring-loaded push terminals. Strip approximately 10mm of insulation
from the ends of your speaker cables, twist stranded cable or use crimped bootlace ferrule on the ends. Depress the push lever, insert the
cables into the hole and release the lever. Positive, ‘+’ connections should be made to the red terminal, Negative, ‘-‘ connections should go
to the black terminal. If “daisy-chaining” connections to several speakers, either twist two wires together prior to inserting in the terminal
or insert two wires together.
Copyright © 2018 Martin Audio Ltd. 2 ADORN QUICK START GUIDE V1.0
QUICK START GUIDE
Wall Mounting
Wall brackets are supplied with all models. The bracket is a three-part design which allows adjustment in both horizontal and vertical
planes.
The first stage is to disassemble the bracket so that the cabinet half can be fitted to the speaker and the wall section attached to the wall.
A 4mm Allen Key is required. If adjustment is only required in one plane, vertical or horizontal, the middle section can be removed. This
has the added advantage that the speaker will be closer to the wall.
Fit the wall bracket in the appropriate orientation for horizontal or vertical adjustment. Fixings appropriate for the wall surface and weight
of the cabinet must be used to ensure a safe and secure installation.
Copyright © 2018 Martin Audio Ltd. 3 ADORN QUICK START GUIDE V1.0
QUICK START GUIDE
Fit the cabinet half of the bracket to the speaker using the four screws in the centre of the rear of the cabinet.
The cabinet can be fitted to the wall by linking the two halves of the bracket using the M4 Allen head bolt.
Ceiling mount
An alternative option is to ceiling mount the ADORN speakers using the optional Ceiling Bracket part number CDDCB5.
Accessories
ADORN COVER Waterproof connector cover
ADORN GRILLE Water resistant grille
Copyright © 2018 Martin Audio Ltd. 4 ADORN QUICK START GUIDE V1.0
QUICK START GUIDE
System Examples
System 1 - A basic ADORN system
System input connected to a VIA2502 Amplifier. Up to four ADORN A40 or A55 speakers connected per channel. The speakers are wired
in parallel by “daisy-chaining” speaker connections from each speakers’ push terminal inputs.
ADORN A40 / A55 ADORN A40 / A55
2
1
SYSTEM INPUT
MARTIN AUDIO
LON DON
PROTECT
CLIP
-6 dB
SIGNAL
BRIDGE
POWER
VIA2504
AMPLIFIER
System 2 - Adding a DX0.5 system processor
System input is to the DX0.5, this adds system EQ and limiting to protect the system from abuse by over-driving. Two of the DX0.5 outputs
are connected to the VIA2502 amplifier inputs. The VIA2502 is connected to the ADORN A40 or A55 speakers as in system 1.
ADORN A40 / A55 ADORN A40 / A55
2
1
PROTECT
CLIP
-6 dB
MARTIN AUDIO
LON DON
SIGNAL
BRIDGE
POWER
VIA2504
AMPLIFIER
SYSTEM INPUT
DX0.5 LOUDSPEAKER MANAGEMENT SYSTEM
NAV/EDIT
1
EDIT2EDIT3
ENTER ESC UTILITY
CLIP CLIP
LIMIT LIMIT LIMIT LIMIT LIMIT LIMIT
CLIP CLIP CLIP CLIP CLIP CLIP
+15 +15
+15 +15 +15 +15 +15 +15
+9 +9
+3 +3 +9 +9 +9 +9 +9 +9
0 0 +3 +3 +3 +3 +3 +3
-10 -10 0 0 0 0 0 0
-20 -20
-15 -15 -15 -15 -15 -15
EDIT EDIT EDIT EDIT EDIT EDIT EDIT EDIT
MUTE MUTE
MUTE
MUTE MUTE MUTE MUTE MUTE
1A 2B 3 4 5 6
USB
DX0.5
LOUDSPEAKER
PROCESSOR
Copyright © 2018 Martin Audio Ltd. 5 ADORN QUICK START GUIDE V1.0
QUICK START GUIDE
System 3 - Adding a subwoofer
System input is again to the DX0.5. An additional VIA2502 amplifier (or VIA5002 for more powerful subwoofers) is added to power a pair
of SX100 subwoofers. This is routed from 1 or 2 outputs from the DX0.5 depending on whether a mono or stereo feed is required for the
subs. Inputs and outputs to the VIA2502 driving the ADORN A50 or A55s is identical to the previous system.
ADORN A40 / A55 ADORN A40 / A55
2
1
PROTECT
CLIP
-6 dB
MARTIN AUDIO
LON DON
SIGNAL
BRIDGE
POWER
SX110 SUBWOOFER
SYSTEM INPUT
MARTIN AUDIO
LON DON
DX0.5 LOUDSPEAKER MANAGEMENT SYSTEM
2
1
PROTECT
CLIP
-6 dB
SIGNAL
BRIDGE
CLIP CLIP
NAV/EDIT
1
EDIT2EDIT3
ENTER ESC UTILITY
LIMIT LIMIT LIMIT LIMIT LIMIT LIMIT
CLIP CLIP CLIP CLIP CLIP CLIP
+15 +15
+15 +15 +15 +15 +15 +15
+9 +9
+3 +3 +9 +9 +9 +9 +9 +9
0 0 +3 +3 +3 +3 +3 +3
-10 -10 0 0 0 0 0 0
-20 -20
-15 -15 -15 -15 -15 -15
EDIT EDIT EDIT EDIT EDIT EDIT EDIT EDIT
MUTE MUTE
MUTE
MUTE MUTE MUTE MUTE MUTE
1A 2B 3 4 5 6
POWER
USB
SX110 SUBWOOFER
VIA2504
AMPLIFIER
DX0.5
LOUDSPEAKER
PROCESSOR
System 4 - Using a 4-channel VIA amplifier
This system is identical to system 3 but uses VIA2004 four channel amplifier (or VIA5004 if a more powerful system is required) which
makes for a more cost effective and compact solution than using separate amplifiers for driving the subwoofers and ADORN speakers.
ADORN A40 / A55 ADORN A40 / A55
SX110 SUBWOOFER
SYSTEM INPUT
MARTIN AUDIO
LON DON
DX0.5 LOUDSPEAKER MANAGEMENT SYSTEM
3
4
2
1
PROTECT
PROTECT
CLIP
CLIP
-6 dB
-6 dB
SIGNAL
SIGNAL
CLIP CLIP
NAV/EDIT
1
EDIT2EDIT3
ENTER ESC UTILITY
LIMIT LIMIT LIMIT LIMIT LIMIT LIMIT
CLIP CLIP CLIP CLIP CLIP CLIP
+15 +15
+15 +15 +15 +15 +15 +15
+9 +9
+3 +3 +9 +9 +9 +9 +9 +9
0 0 +3 +3 +3 +3 +3 +3
-10 -10 0 0 0 0 0 0
-20 -20
-15 -15 -15 -15 -15 -15
EDIT EDIT EDIT EDIT EDIT EDIT EDIT EDIT
MUTE MUTE
MUTE
MUTE MUTE MUTE MUTE MUTE
1A 2B 3 4 5 6
POWER
USB
SX110 SUBWOOFER
VIA2504
AMPLIFIER
DX0.5
LOUDSPEAKER
PROCESSOR
Copyright © 2018 Martin Audio Ltd. 6 ADORN QUICK START GUIDE V1.0
Martin Audio Limited
Century Point
Halifax Road
Cressex Business Park
High Wycombe
Buckinghamshire
HP12 3SL
England
FOR SALES ENQUIRIES:
UK
Telephone: +44 (0)1494 535312
E-mail: info@martin-audio.com
NORTH AMERICA
Telephone: 818 649 7776
www.martin-audio.com
All information is Copyright © 2018 Martin Audio Ltd.
Martin Audio, the Martin Audio logo and Hybrid are registered trademarks of Martin Audio Ltd. in the United Kingdom, United States
and other countries; all other Martin Audio trademarks are the property of Martin Audio Ltd.
Loading...