Martin U-DS90W, U-DS90B Instruction Manual

Creation Station Table

Assembly Instructions

Video Assembly Instructions:

Go to www.MartinUniversalDesign.com and click on
Assembly Instructions to watch a video for HOW TO
ASSEMBLE the U-DS90W / U-DS90B, Creation Station
Table.

4444 Lawton Street, Detroit, MI, 48208 USA • Tel: [phone] • Fax: [phone]
Email: [e-mail] • www.MartinUniversalDesign.com

IMPORTANT:

If you have difficulty assembling your U-DS90W/U-DS90B
Creative Center or need customer service assistance.
Please call: Martin Universal Design, Inc. Customer service
Hot Line at 1-313-895-0700. If you need additional parts, it
is not necessary to contact your dealer. Our customer ser­vice rep. will forward them to you immediatly.

01/2012 SM

Page 2

U-DS90W / U-DS90B
Creation Station Table Parts List

24”x40” Top

Upper Base End

Lower Base End

(2 pieces)

(2 pieces)

Drawer Supports

Tilt Mechanism (2 Pieces)

Top L-Bracket

(4 Pieces) 6x55mm (6 pieces) Washer (4 Pieces)

(2 Pieces)

6x28mm (8 pieces)

5x14mm

(8 Pieces)

: Table Components

: Fasteners and Tools

Allen Wrench

Wrench (10mm)

Foot Bar

Cross Support

Top Support

Pencil Ledge

Drawer Support Rods

(4 pieces)

Casters

End Caps (2 pieces)

Footbar Spacers

(4 Pieces) Nuts (4 Pieces)

Cross Support

(2 Pieces) Collars (4 pieces)

4x12mm

6x65mm (6 pieces)

Drawers:

(2 Pieces)

Wrench (12mm)

Packaged with Casters

Phillips Head screw driver
NOT INCLUDED

Please see Last Page of assembly
sheet for drawers.

01/2012 SM

Step 1: Lower Base Ends

Fastener parts needed for this step: T= 2 ea., N=2 ea.

• Take the lower base end units (Part C ) and line

up next to each other so the welds are on the inside.

• Take 6x65mm bolt (Part T ) and insert it in the

base end from the outside. Once inserted, slide the

footbar spacer (Part N ) onto the the 6x65 mm bolt

(Part T )making sure the curved end is facing the

lower base and the at part is toward the foot bar.

• Spin foot bar (Part D ) onto the 6x65 mm bolt (Part

T ) using the Allen Wrench (Part W ) to hold the

6x65 mm bolt (Part T ) still. Be sure to leave it loose.

• Take opposite lower base end and repeat Step 1-2

with that base end.

Page 3

C

D

T

N

T

N

D

• Line up the base end and secure it loosely to the

foot bar (Part D ). using the Allen Wrench (Part W

) and be sure to leave loose for Step 2.

Step 2: Attaching Cross Support

Fastener parts needed for this step: O=4 ea. M=2 ea.

•Locate the 2 vertical holes on the Lower Base Ends
(Part C ) and insert the 6x55mm bolts (Part O )
through these holes.

• Slide on cross support end cap (Part M ) mak­ing sure curved part faces the lower base end
(Part C ) and at part faces the Cross Sup­port (Part E ). DO NOT OVER TIGHTEN to
avoid damaging the cross support end caps.

• Line up holes on Cross Support (Part E )

O

T

C

M

O

E

M

E

and tighten with the allen wrench (Part W ).

• Place other support cap up to opposite leg, thread
bolts through the holes and tighten to cross support
(Part E )

• Go back and tighten all 6 bolts so they are snug but
again, BE CAREFUL NOT TO OVER TIGHTEN.

O

01/2012 SM