Martin MAC III Performance User Manual

Page 1
MAC III™ PERFORMANCE
USER MANUAL
Page 2
Dimensions
All measurements are expressed in millimeters
The minimum center-to-center distance can be reduced if pan limits are set via the control menus
nies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by
the use of, inability to use or reliance on the information contained in this manual. The Martin logo, the Martin name and all other
trademarks in this document pertaining to services or products by Martin Professional A/S or its affiliates and subsidiaries are trade-
marks owned or licensed by Martin Professional A/S or its affiliates or subsidiaries.
P/N 35000247, Rev. B
Page 3
Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
AC power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power input and primary fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
About the discharge lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Lamp replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
DMX data link. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Tips for reliable data transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Physical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Control panel operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DMX address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
DMX modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Fixture ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Personality – tailoring performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Fixture information readouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
DMX signal monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Test sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Manual control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Setup Wizard menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Adjusting settings via DMX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Resetting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Lamp on / off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Adjusting lamp power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Illuminating the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Control menu setting overrides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Effects. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Shutter and strobe effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Dimming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cyan, Magenta, Yellow and CTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Color wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Rotating gobos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Gobo animation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Beam effect (frost). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Focus and zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Pan and tilt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Rotatable Framing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Followspot mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
RDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
RDM port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
RDM ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
RDM communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Service and maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Tilt lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Service utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Event log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Calibrating effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Software installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Page 4
Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Replacing a color filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Gobos in the MAC III Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Replacing the gobo animation wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Removing modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
MAC III Performance DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Control panel menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Service and display messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Service warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Page 5

Safety Information

WARNING!
Read the safety precautions in this section before
installing, powering, operating or servicing this
product.
The following symbols are used to identify important safety information on the product and in this manual:
DANGER!
Safety hazard. Risk of severe
injury or death.
This product is for professional use only. It is not for household use. This product presents risks of severe injury or death due to fire and burn hazards, electric shock, lamp
explosion and falls.
Read this manual before installing, powering or servicing the fixture, follow the safety precautions listed below and observe all warnings in this manual and printed on the fixture.
If you have questions about how to operate the fixture safely, please contact your Martin supplier or call the Martin 24-hour service hotline on +45 8740 0000, or in the USA on 1-888-tech-180.
PROTECTION FROM ELECTRIC SHOCK
• Disconnect the fixture from AC power before remo ving or installing any cov er or part – including the lamp and fuses – and when not in use.
• Ensure that the fixture is electrically connected to ground (earth).
• Use only a source of AC power that complies with local building and electrical codes and has both overload and ground-fault (earth-fault) protection.
• Connect the fixture to AC power either using the supplied power cable or via 3-conductor cable that is rated minimum 20 amp, extra hard usage. Suitable cable types include ST, STW, SEO, SEOW and STO.
• Before using the fixture, check that all power distribution equipment and cables are in perfect condition and rated for the current requirements of all connected devices.
• Isolate the fixture from power immediately if the power cable or power plug are in any way damaged, defective or wet, or if they show signs of overheating.
• Do not expose the fixture to rain or moisture.
• Refer any service operation not described in this manual to an authorized Mart in Service partner.
DANGER!
Refer to
manual before
installing,
powering or
servicing.
DANGER!
Hazardous voltage. Risk of severe or lethal
electric shock.
Warning!
Fire hazard.
Warning!
Burn hazard.
Hot surface. Do
not touch.
Warning!
Risk of eye injury. Safety glasses must
be worn.
Warning!
Risk of hand injury. Safety
gloves must be
worn.
Safety Information 5
Page 6
LAMP SAFETY
• Prolonged exposure to an unshielded discharge lamp can cause eye and skin burns. Do not stare directly into the light output. Never look at an exposed lamp while it is lit.
• Do not operate the fixture with missing or damaged covers, shields, lenses or ultraviolet screens.
• A hot discharge lamp is under pressure and can explode without warning. Allow the fixture to cool for at least 2 hours 45 minutes and protect yourself with safety glasses and gloves before handling a lamp or servicing the fixture internals.
• Replace the lamp immediately if it becomes visual ly deformed, damaged or in any way defective
• Monitor hours of lamp use and lamp intensity and replace the lamp when it reaches the limit of its service life as specified in this manual or by the lamp manufacturer.
• Install only an approved lamp.
• If the quartz envelope of a discharge lamp is broken, the lamp releases a small quantity of mercury and other toxic gases. If a discharge lamp explodes in a confined area, evacuate the area and ventilate it thoroughly. Wear nitrite gloves when handling a broken discharge lamp. Treat broken or used discharge lamps as hazardous waste and send to a specialist for disposal.
PROTECTION FROM BURNS AND FIRE
• The exterior of the fixture becomes very hot – up to 170° C (338° F) – during use. Avoid contact by persons and materials. Allow the fixture to cool for at least 2 hours 45 minutes before handling.
• Keep all combustible materials (e.g. f abric, wood, paper) at least 0.2 m (8 in.) aw ay from the fixture. Keep flammable materials well away from the fixture.
• Provide a minimum clearance of 0.1 m (4 in.) around fans and air vents.
• Do not illuminate surfaces within 2.5 m (100 in.) of the fixture.
• Position or shade the head so that the lens does not face the sun at any time during daylight hours. The lens can focus the sun's rays inside the fixture, creating a potential fire hazard.
• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).
• Do not modify the fixture in any way not described in this manual or install other than genuine Martin parts. Do not stick filters, masks or other materials onto any lens or other optical component. Use only Martin-approved accessories to mask or modify the light beam.
• Do not attempt to bypass a thermostatic switch or fuse. Replace defective fuses with ones of the specified type and rating only.
PROTECTION FROM INJURY DUE TO FALLS
• Do not lift or carry the fixture alone.
• Use two evenly spaced clamps to suspend the fixture from rigging structures. Do not use only one clamp.
• When clamping the fixture to a truss or other supporting structure at any other angle than with the yoke hanging vertically downwards, use two half-coupler clamps. Do not use G-clamps, quick-trigger clamps or any other type of clamp that does not completely encircle the supporting structure when fastened.
• When suspending the fixture, ensure that the supporting structure and all hardware used can hold at least 10 times the weight of all devices suspended from them.
• Do not use the handles in the base or the handles on the top of the yoke for hoisting or secondary attachment.
• Install as described in this manual a secondary attachment such as a safety cable that is approved by an official body such as TÜV as a safety attachment for the weight of all the fixtures it secures. The safety cable must comply with EN 60598-2-17 Section 17.6.6 and be capable of bearing a static suspended load ten times the weight of the fixture.
• Check that all external covers and rigging hardware are securely fastened.
• Block access below the work area and work from a stable platform whenever installing, servicing or moving the fixture.
6 MAC III Performance user manual
Page 7

Introduction

Thank you for selecting the Martin™ MAC III Performance™. This moving-head spotlight features:
• 1500 Watt short-arc high-output Osram HTI 1500W/60/P50 discharge lamp with semi-hot restrike
• Backlit graphic display and battery power (mains power not required for fixture setup)
• Full-range mechanical dimmer with four dimming curve options, plus mechanical shutter
• Full-spectrum CMY color mixing and CTO color temperature control
• 7 interchangeable dichroic color filters
• Gobo wheel with 5 interchangeable rotating gobos with 16-bit position indexing
• Interchangeable gobo animation wheel
• 4-blade continuously rotatable framing with quick access to framing shapes using pre-programmed macros
• Interchangeable frost filter (can be replaced with four-facet rotating prism from the MAC III Profile, available as an accessory)
•Iris
• Variable focus and zoom with 3-zone zoom/focus linking system
• 540° of pan and 268° of tilt with user-settable pan/tilt limits
• Electronic “flicker-free” ballast and auto-sensing switch-mode power supply.
For the latest firmware updates, documentation, and other information about this and all Martin Professional products, please visit the Martin website at http://www.martin.com
Comments or suggestions regarding this document may be e-mailed to service@martin.dk or posted to: Technical Documentation, Martin Professional A/S, Olof Palmes Allé 18, DK-8200 Aarhus N, Denmark.

Unpacking

The MAC III Performance is packaged in either a cardboard box or a flightcase that is designed to protect the product during shipment. The following items are included:
• 1500 W discharge lamp (installed)
• Two 16 AT fuses (installed)
• 2 omega brackets for clamp attachment
• This user manual

Using for the first time

Before applying power to the fixture:
• Carefully review the safety information starting on page 5.
• Check that the fuses in the Live and Neutral fuseholders near the main on/off switch match the local AC power voltage as described in “Power input and primary fuses” on page 8.
• If necessary, install a cord cap (mains plug) on the power cable as described in “Power connection” on page 8.
• Unlock the tilt lock as described on page 33.
• Check that the base is fastened securely so that the torque reaction when the head is panned does not cause the fixture to move.
When powered up, check lamp alignment as described on page 10.

Packing

Important! Release the tilt lock before repacking in the flightcase.
The tilt lock must be released during transportation in the MAC III flightcase.
Introduction 7
Page 8

AC power

Warning! For protection from electric shock, the fixture must be grounded (earthed). The AC mains supply must be fitted with a fuse or circuit breaker and ground-fault (earth-fault) protection.
Important!Check that the correct fuse is installed before applying power.

Power input and primary fuses

The MAC III Performance features an auto-sensing switch-mode power supply that automatically adapts to 200-240 V (nominal) AC power at 50 or 60 Hz. It is protected by two 16 A slow-blow primary fuses, one for the live conductor and one for the neutral conductor.
To install fuses:
1. Disconnect the fixture from
AC power.
2. Use a flat-headed
screwdriver to open the two main fuseholders, located above the power on/off switch and mains input socket.
3. Install one 16 AT fuse in
each fuseholder.
4. Reinstall the fuseholders
before reapplying power.

Power connection

Important! Connect the MAC III
Performance directly to AC power. Do not connect it to a dimmer system; doing so may damage the fixture.
If you install a cord cap (mains plug) on the power cable to allow connection to power outlets, install a grounding-type (earthed) plug, following the plug manufacturer’s instructions. Table 1 shows some possible mains power pin identification schemes; if the pins are not clearly identified, or if you have any doubts about proper installation, consult a qualified electrician.
To apply power, first check that the head tilt locks are released and then set the power switch on the base to the “I” position.
Wire Color Pin Symbol Screw (US)
brown live L yellow or brass blue neutral N silver yellow/green ground (earth) green
The MAC III Performance is su pplied with a power cable with a Neutrik PowerCon NAC3FCA cable connector for power input. If you replace the power cable, obser ve the pinout marked on this cable connector. Connect the terminal marked to ground (earth), the terminal marked N to neutral, and the terminal marked L to live. Replacement power cable must be 3-conductor, rated minimum 20 amp, extra-hard usage. Suitable cable types include ST, STW, SEO, SEOW and STO.
Table 1: Cord cap connections
8 MAC III Performance user manual
Page 9

Lamp

About the discharge lamp

The MAC III Performance is designed for use with an Osram HTI 1500W/60/P50 lamp. This highly efficient double-ended short-arc source provides a color temperature of 6000 K, a color rendering index greater than 85, an average service life of 750 hours and semi-hot restrike, meaning that a hot lamp is ready to strike again after 90 seconds.
Lamp power is automatically reduced to approximately 800 W after 10 seconds when the fixture is blacked out in order to reduce cooling fan activity and power consumption. The lamp returns to 1500 W as soon as the dimmer and/or shutter are opened.
Warning! Installing any other lamp may create a safety hazard or damage the fixture!
To reduce the risk of explosion, replace the lamp when it reaches the limit of its average service life, i.e. when usage reaches 750 hours. Never exceed the lamp’s average service life by more than 10%. To read lamp hours in the fixture’s display, refer to the section on lamp hours readouts on page 19. Replace the lamp immediately if it is deformed or in any way defective.
For maximum service life, avoid powering the lamp off until it has warmed up for at least 5 minutes.

Lamp replacement

Warning! W ear safety glasses and gloves when handling lamps. The clear lamp bulb is integral with the ceramic lamp base. Do not try to separate the bulb from the base.
Important! The lamp can be a stiff fit in its holder. Twist the lamp base a full 45° clockwise when installing to ensure that the lamp contacts are fully engaged.
Replacement lamps are available from your Martin dealer requesting P/N 97010326. The clear bulb must be perfectly clean. Do not touch it with your fingers. Clean the lamp with an alcohol
wipe and polish it with a dry cloth before installing, particularly if you accidentally touch the bulb. To replace the lamp:
1. Disconnect the fixture from power and allow it to cool for at
least 2 hours 45 minutes.
2. Lock the head.
3. Release the screw on the lamp access cover and open the
cover.
4. Grasp the ceramic lamp base, twist it 45° counterclockwise
and withdraw the lamp from the fixture as shown in Figure 2.
5. The lamp base has two metal contacts, one narrow and one
wide, that fit into corresponding narrow and wide slots in the lampholder. Line up the contacts on the replacement lamp’s base with the corresponding slots in the lampholder, slide the lamp into the fixture so that the contacts are fully engaged in the slots, and then twist the lamp base a full 45° clockwise until it locks into position with a noticeable click. The lamp is a stiff fit and trying to strike a lamp that is not correctly installed can cause damage that is not covered by the product warranty, so ensure that the lamp is correctly locked into po si ti on.
6. Close the lamp access cover and tighten the screw to
secure the cover before reapplying power.
7. After installing a new lamp, reset the lamp hour counter (see
the section on lamp hours readouts on page 19).
Figure 2: Lamp removal / refitting
Lamp 9
Page 10
Lamp adjustment
Warning! Adjust the lamp with the fixture cool. The fixture may become hot during adjustment, so wear heat-resistant safety gloves.
As well as being undesirable for aesthetic reasons, a significant hot-spot in the beam will focus extra heat onto optical components and may cause damage that is not covered by the product warranty.
After fitting a new lamp, adjustment may be required to obtain an even beam. To adjust the lamp:
1. If the fixture has been in use, allow it to cool for at least 2 hours 45 minutes to avoid the danger of burns,
and wear heat-resistant safety gloves.
2. Apply power, allo w the fixture to reset, then set
zoom to narrow, turn on the lamp and open the mechanical shutter.
3. Aim the fixture at an even surface and make
sure no further commands can be sent by DMX.
4. See Figure 3. Screw the three lamp adjustment
screws in or out to obtain the most even beam.
Figure 3: Lamp adjustment screws
10 MAC III Performance user manual
Page 11

DMX data link

The MAC III Performance has 5-pin locking XLR sockets for DMX and RDM input and output. The default pin-out on both sockets is:
• pin 1 to shield
Port 1, DMX and RDM communication:
• pin 2 to data 1 cold (-)
• pin 3 to data 1 hot (+)
Port 2, not used by default but available for data communication:
• pin 4 to data 2 cold (-)
• pin 5 to data 2 hot (+).
The default use of Port 1 for DMX and RDM can be altered in the control panel (see “Personality – tailoring performance” on page 16).

Tips for reliable data transmission

• Use shielded twisted-pair cable designed for RS-485 devices: standard microphone cable cannot transmit control data reliably over long runs. 24 AWG cab le is suitable for runs up to 300 meters (1000 ft). Heavier gauge cable and/or an amplifier is recommended for longer runs.
• To split the serial link into branches, use a splitter such as the Martin 4-Channel Opto-Isolated RS-485 Splitter/Amplifier.
• Do not overload the link. Up to 32 devices may be connected on a serial link.
• Install a DMX termination plug on the last fixture on the link.
To connect the data link
1. Connect the DMX data output from the controller to the MAC III Performance’s data input (male XLR)
socket.
2. Run the data link from the MAC III Performance’s data output (female XLR) socket to the data input of
the next fixture.
3. Terminate the data link by connecting a 120 Ohm, 0.25 Watt resistor between the data 1 hot (+) and cold
(-) conductors (and between data 2 hot and cold if used) at the data output of the last fixture on the link. If a splitter is used, terminate each branch of the link.
DMX data link 11
Page 12

Physical installation

Warning! The MAC III Performance has a powerful pan motor. The torque reaction when the head is panned suddenly can cause the base to move if the fixture is standing unsecured on a surface. Do not apply power to the MAC III Performance unless the base is securely fastened to a surface or to rigging hardware.
Warning! Use 2 clamps to rig the fixture. Do not hang the fixture from only one clamp. Lock each clamp with both 1/4-turn fasteners. Fasteners are locked only when turned fully clockwise.
Warning! When suspending the fixture above ground level, secure it against failure of primary attachments by attaching a safety wire that is approved as a safety attachment for the weight of the fixture to the attachment point in the base. Do not use the carrying handles for secondary attachment.
Warning! When clamping the fixture to a truss or other structure at any other angle than with the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structu r e when fastened.
Warning! Position or shade the head so that the lens does not face the sun at any time during daylight hours. The MAC III Performance’ s lens can focus the sun's rays inside the fixture, creating a potential fire hazard and causing internal damage.
Important! Do not point the output from other lighting fixtures at the MAC III Performance from a distance of less than 3 m (10 ft.), as intense illumination can damage the display.
The MAC III Performance can be fastened to a surface such as a stage or clamped to a truss in any orientation. Clamps must be half-coupler type (see Figure 5) unless the fixture is installed with the yoke hanging vertically downwards. The mounting points allo w th e clamp brackets to be fastened parallel, perpendicular or at 45° to the front, as shown Figure 4.
Pan and tilt range can be limited via the control panel to allow fixtures to be installed close to each other or to obstacles with no risk of collision (see
PAN/TILT SETTINGS on page 16).
Clamping the fixture on a truss
1. Check that the rigging clamps are
undamaged and can bear at least 10 times the weight of the fixture. Check that the structure can bear at least 10 times the weight of all installed fixtures, clamps, cables, auxiliary equipment, etc.
12 MAC III Performance user manual
Figure 4: Clamp bracket positions
Page 13
2. Bolt each clamp securely to a clamp bracket with an M12 bolt (minimum
grade 8.8) and lock nut.
3. See Figure 6. Note the position of
the arrows on the bottom of the base that indicate the front of the fixture.
Figure 6: Front of fixture
4. Align a clamp with 2 mounting points in the base. See
Figure 7. Insert the fasteners into the base and turn both levers a full 1/4-turn clockwise to lock. Install the second clamp.
5. Block access under the work area. Working from a stable
platform, hang the fixture on the truss with the arrows marked FRONT printed on the base of the fixture facing towards the area to be illuminated. Tighten the rigging clamps.
Figure 5: Martin
half-coupler clamp
6. See Figure 8. Install a safety wire that is approved as a
safety attachment for the weight of the fixture by looping it through the safety attachment wheel on the bottom of the base.
7. Check that the tilt lock is released. Check that there are no
combustible materials within 0.2 m (8 in.) or surfaces to be illuminated within 2.5 m (100 in.) of the fixture, and that there are no flammable materials nearby.
8. Check that there is no possibility of heads or yokes colliding
with other fixtures. Note that pan and tilt range on the MAC III Performance can be restricted by setting minimum and maximum limits via the control menus. This feature allows fixtures to be installed closer together or closer to obstacles.
9. Check that other lighting fixtures cannot project light at the
MAC III P erformance from a distance of less than 3 m (10 ft.), as intense illumination can damage the MAC III Performance’s display.
Figure 7: Locking 1/4-turn fasteners
Figure 8: Safety cable attachment
point
Physical instal la tion 13
Page 14

Control panel operations

You can configure individual fixture settings such as the MAC III Performance’ s DMX address, read out data, execute service and view the event log using the fixture’s backlit graphic display and control panel. The control menu overview starting on page 55 gives a complete list in table form of the menus and commands available.
A
C
Figure 9: Display and control panel
B
After a pause while the fixture boots and resets, the DMX address and any status messages (see page 59) appear in the graphic display A when the MAC III Performance is powered on.
Using the control panel
Click (i.e. press once) the jog wheel B once to enter the menus. Rotate the jog wheel to scroll up and down menus and click the jog wheel once to make a selection. Rotating the jog wheel faster gives high-speed scrolling.
Once you have made a selection, either click the jog wheel to save it or press the Escape button C to cancel. If you save the selection, Saving... is displayed for 1 second. If you cancel, the menu returns to the previously saved value. Press the Escape button to step backwards through the menus.
The jog wheel and Escape button continue to function while the Saving... message is displayed.
Status LED on jog wheel
An LED in the center of the jog wheel indicates fixture status depending on the color displayed and DMX status depending on whether the LED flashes or lights constantly:
GREEN: All fixture parameters normal.
AMBER: Warning active (service interval exceeded, for example). If ERROR MODE is set to Normal, the warning message will be shown in display. If ERROR MODE is set to Silent, the display must be activ ated with the jog wheel to display the warning message.
RED: Error detected. If ERROR MODE is set to Normal, the error message will be shown in display. If ERROR MODE is set to Silent, the display must be activated with the jog wheel to display the error message.
FLASHING: No DMX signal detected.
LIGHTS CONSTANTLY: Valid DMX signal detected.
If an error has been detected and the LED is red when the fixture is powered off, the LED will continue to flash red slowly. This feature allows easy identification of fixtures that require service intervention even if fixtures are disconnected from power.
Martin flightcases for the MAC III Performance contain a small window through which the status LED is visible.
14 MAC III Performance user manual
Page 15
Battery power
The display and control panel are powered by the MAC III P erf ormance’s onboard battery . This giv es access to the most important functions in the control panel – including DMX addressing – when the fixture is not connected to AC power.
To activate the display when the fixture is not connected to power, press the Escape button. The display extinguishes after 10 seconds with no jog wheel activity and the control panel is de-activated after 1 minute with no jog wheel activity. Press the Escape button again to re-activate.
Mains power indicator
When the fixture is connected to AC mains power, a ‘battery recharging’ icon appears in the display. When the battery is fully charged, the battery icon is replaced a mains plug icon.
Status indicators in display
The status indicators on the right of the display have the following functions:
LAMP lights green when the lamp is powered.
ETHERNET lights green when the MAC III Perf ormance is correctly connected to an Ethernet network (at the moment there is no provision for direct connection to Ethernet).
DMX lights green when the MAC III Performance is receiving a valid DMX signal.
PAN/TILT lights yellow when pan/tilt limits have been activated (see page 16) and lights orange when Followspot Mode is enabled (see “Rotating Framing” on page 26).
Shortcuts pop-up
If you hold the Escape button pressed in for 2 - 3 seconds, a pop-up window with shortcuts to important commands appears. Select a command and click the jog wheel to activate, or press Escape to cancel.
RESET resets the whole fixture
LAMP ON/OFF strikes or douses the lamp.
ROTATE DISPLAY rotates the MAC III Performance display.
FOLLOWSPOT MODE calls up the followspot menu.
EVENT LOG calls up the event log menu.
Settings stored permanently
The following settings are stored permanently in the fixture memory and are not affected by powering the MAC III Performance off and on or by updating the fixture software:
• DMX address
• DMX Protocol setting
• Fixture ID
• All personality settings (pan/tilt and pan/tilt limit, linked zoom/focus, lamp cooling, fan clean mode, dimming curve, DMX lamp off, DMX reset, parameter shortcuts, all display settings, error mode)
• Factory settings
• Fixture info (resettable power-on, lamp-on, lamp strikes, and air filter counters)
• All Service settings (adjust, calibration, firmware)
These settings can be returned to factory defaults using the control menus or via DMX.

DMX address

The DMX address, also known as the start channel, is the first channel used to receive instructions from the controller. For independent control, each fixture must be assigned its own control channels. If you give two MAC III Performances the same address, they will behave identically. Address sharing can be useful for diagnostic purposes and symmetrical control, particularly when combined with the inverse pan and tilt options.
Control panel operations 15
Page 16
DMX addressing is limited to channels 1 - 478 in 16-bit mode and 1 - 472 in 16-bit extended mode. The upper limit makes it impossible to set the DMX address so high that you are left without enough control channels for the fixture.
DMX address setting
To set the fixture’s DMX address:
1. Press the jog wheel to enter the main menu.
2. Rotate the jog wheel to scroll down to DMX ADDRESS, then
click the jog button. Rotate the jog wheel to scroll to the desired address and click the jog button to save.
3. Press the Escape button to step back to the main menu.

DMX modes

The PROTOCOL SET menu lets you set the MAC III Perf ormance to one of the two DMX operating modes, 16-bit and 16-bit extended.
The basic 16-bit mode offers coarse control of all effects plus fine control of gobo indexing angle on both gobo wheels, pan and tilt. The 16-bit extended mode requires six more DMX channels than the basic 16-bit mode and provides all features of the basic 16-bit mode plus fine control of the dimmer, zoom and focus. It also allows the selection of frame shape macros, adjustment of their size and adjustment of crossfading speed from one macro to another.
The MAC III Performance requires 34 DMX channels in 16-bit mode and 40 DMX channels in 16-bit extended mode.
DMX mode setting
To set the fixture’s DMX mode:
1. Click the jog wheel to enter the main menu.
2. Rotate the jog wheel to scroll down to PROTOCOL SET, then clic k the jog wheel. Rotate the jog wheel to
select either 16 bit or 16 Bit Ext., then click the jog wheel to save.
3. Press the Escape button to step back to the main menu.

Fixture ID

The MAC III Performance lets you set a four-digit ID number to ease identification of the fixtures in an installation. When a fixture is powered on for the first time, it displays its DMX address by default. As soon as you set an ID number other than 0000 in FIXTURE ID , the MAC III Performance will display this ID number by default.
To let you distinguish easily between ID numbers and DMX addresses, the ID number is always displayed with four digits and DMX address is displayed with between one and three digits.
Personality – tailoring performance
The MAC III Performance provides several options that let you optimize the fixture for different applications in the PERSONALITY menu:
• The PAN/TILT SETTINGS menu gives three options:
- PAN/TILT CONTROL lets you swap and/or invert pan and tilt
and activate the pan and tilt limits you define in PAN & TILT LIMIT SETTINGS (see below).
- MOVE ON RESET lets you choose if you want pan and tilt to
move when the fixture resets or not. Pan and tilt movement can be a useful visual sign that fixtures in a rig are powering up and resetting.
- PAN & TILT LIMIT SETTINGS lets you define minimum and
maximum limits for both pan and tilt angles, making it possible to install fixtures close to obstacles such as other fixtures with no risk of collision. Settings are based on the following principles:
16 MAC III Performance user manual
Page 17
Pan range for pan limit purposes runs from 0° to 360° clockwise as seen looking at the fixture from the bottom of the base towards the yoke, as if the fixture was hanging downwards underneath you.
Tilt range is +134° and -134° either side of 0°, which is the head straight up position with the front glass pointed directly away from the base.
The light beam points fully forward (the front of the fixture is indicated by the arrows printed under the base) when pan is set to 90° or 450° and tilt is set to +90°.
Selecting Inside keeps pan and tilt inside the limits you set – i.e. angles define a ‘safe zone’. Selecting Outside keeps pan and tilt outside the limits you set – i.e. angles define a ‘no-go zone’. Limits are not activated until the head is panned and tilted into its safe zone or out of its no-go zone. When pan/tilt limits are active, the PAN/TILT light at the bottom right of the display lights yellow.
See Figure 10. T o limit pan so that it sta ys inside a saf e zone 20° either side of fully forw ard and limit tilt so that it stays inside a safe zone 18° either side of fully forward, for example:
1. Set PAN MINIMUM to 70°.
2. Set PAN MAXIMUM to 110°.
3. Set TILT MINIMUM to +72°.
4. Set TILT MAXIMUM to +108°.
5. Set P/T LIMIT AREA to Inside.
+72°
+70°
+90°
+90°
Safe zone
+108°
Safe zone
+110°
Pan safe zone
Inside, min. +70°, max. +110°
Figure 10: Pan/Tilt limit settings
Important! Regardless of the pan and tilt limits you set, when you power the fixture off, the head will sink under
gravity to the nearest rest position (e.g. with the lens pointing vertically downwards if the fixture is hanging in a rig, or to one side if the fixture is standing fastened to a horizontal surface). When you power the fixture on, the head will not move until the fixture receives a pan or tilt command. When a command is received, if the head’s rest position is outside its pan/tilt limits, the head will move slowly until it is within its limits. This feature reduces the risk of damage caused by a collision.
Pan and tilt limits can quickly be returned to the factory default setting (all limits at 0°, pan/tilt limits disabled) by setting DEFAULT LIMIT SETTINGS to On and clicking with the jog wheel to confirm.
SPEED SETTINGS lets you set PAN & TILT SPEED to Normal, Fast (optimized for speed) or Slow (optimized for smooth movement – useful in long-throw applications). Likewise, you can set EFFECT SPEED to Normal, Fast or Slow. You can also set effect speed to Follow P/T speed, in which effects will always use whatever speed is set for pan and tilt.
The FANS
- LAMP COOLING sets the lamp cooling effect to 50% or 80%. The color temperature of the lamp and
lamp performance towards the end of the lamp life vary slightly with the level of lamp cooling applied. The default level is 80%, which is recommended for optimum performance over the full life of the lamp. Setting to 50% gives a slightly lower color temperature and quieter fan operation but accelerates the gradual reduction in output which is normal over the lifetime of a discharge lamp.
- FAN CLEAN gives three option s for automatically clearing dirt from fans:
menu gives three cooling fan options:
Off sets fans to normal operation with no fan cleaning function. Auto sets fans to normal operation, but if a fan error is detected, the fan that has reported an error
speeds up to 100% for a short period and then returns to normal operation. If the fan error is still detected after three attempts at cleaning, the fan returns to normal operation but continues to report a fan error. This f eature works independently for each of the fans. Attempts at cleaning are reset to zero if the fixture is reset or if FAN CLEAN MODE is updated.
Inside, min. +72°, max. +108°
Tilt safe zone
Control panel operations 17
Page 18
Forced sets all fans to 100% speed until another FAN CLEAN MODE setting is selected.
This feature does not eliminate the need to inspect and clean cooling fans at regular intervals (see “Cleaning” on page 39).
- FAN MODE allows you to set fans to Always on or Follow lamp off mode, in which fan operation is
disabled when the lamp is powered off.
DIMMING CURVE provides four dimming options (see Figure 11):
Output
Output
Output
Output
DMX % DMX % DMX % DMX %
Optically linear VRMS linear Square law Inverse square law
Figure 11: Dimming curve options
- Optically linear – the increase in light intensity appears to be linear as DMX value is increased.
- VRMS linear (S-curve) – light intensity control is finer at low levels and high levels and coarser at
medium levels. This curve emulates the RMS v oltage dimming characteristics of an incandescent lamp such as the tungsten halogen lamp of the Martin™ MAC TW1™.
- Square law – light intensity control is finer at low levels and coarser at high levels .
- Inverse square law – light intensity control is coarser at low levels and finer at high levels.
FOCUS TRACKING sets focus to automatically self-adjust when you use the zoom effect (see “Zoom/focus linking” on page 25).
FOLLOWSPOT MODE enables pan, tilt, or pan and tilt movement to be unlocked so that the head of the fixture can be directed by hand using a user-supplied handle (see “Rotating Framing” on page 26). In followspot mode the motors can be applied as a brake to pan, tilt, or both pan and tilt mov ement to pre vent head movement when the fixture is not “manned”; in this case DMX or menu-based control over pan and tilt is still disabled.
• AUTOMATIC LAMP ON gives three lamp strike options:
- When set to Off, the lamp remains off until a “lamp on” command is received via DMX.
- When set to On, the lamp strikes automatically after the fixture is powered on.
- When set to DMX, the lamp strikes automatically when the fixture begins to receive DMX data, and
lamp power is shut down 15 minutes after the fixture stops receiving DMX data. Automatic lamp strikes are staggered to prevent all lamps from striking at once. The delay is determined by the fixture address. No matter what the AUTOMATIC LAMP ON setting is, the lamp can be struck by sending a lamp on command via DMX on channel 26 in basic mode or 29 in extended mode.
DMX LAMP OFF and DMX RESET define whether the lamp can be powered off, or whether fixture or individual effects can be reset by sending a DMX command on channel 26 in 16-bit mode or 29 in 16-bit extended mode. If either of these settings are set to Off, you can override this setting and cut lamp power or reset effects by applying a special combination of DMX values (see “MAC III Performance DMX protocol” on page 47).
PARAMETER SHORTCUTS determines whether the gobo wheels and color wheel take the shortest path between two positions (shortcuts enabled), crossing the open position if necessary, or always avoid the open position (shortcuts disabled).
DISPLAY determines whether the display remains on permanently, or goes into sleep mode 2, 5 or 10 minutes after the last movement of the jog wheel or Escape button.
DISPLAY INTENSITY lets you define the brightness of the backlit graphic display. Select Auto for automatic adjustment to match the ambient light level, or manually set the intensity to a level from 0% to 100%.
DISPLAY ROTATION lets you rotate the display manually through 0°, 90°, 180° or 270° so that it can be read easily no matter how the fixture is oriented. If set to Auto, the MAC III Performance senses its orientation and rotates the display automatically.
18 MAC III Performance user manual
Page 19
ERROR MODE enables or disables error warnings. If set to Start, the display is activated and lights up if the fixture needs to report an error. If set to Silent, the fixture does not light the display with error warnings but error messages can still be read when the display is activated manually. In both Start and Silent modes, the status LED in the jog wheel lights amber to indicate a warning and red to indicate an error.

Factory settings

FACTORY SETTINGS lets you restore the fixture’s default setup options. Effect calibration is not affected,
so any effects that have been re-calibrated will not be returned to factory calibration settings.

Fixture information readouts

The following fixture information can be called up in the display:
FIRMWARE VERSION displays the currently installed fixture software version.
POWER ON TIME provides two counters:
- The TOTAL POWER ON counter is not user-resettable and
displays total hours powered on since manufacture.
- The RESETTABLE POWER ON counter is user-resettable
and displays the number of hours the fixture has been powered on since the counter was last reset.
LAMP ON TIME provides two counters:
- The TOTAL LAMP ON counter is not user-resettable and displays total hours the lamp has been
powered on since manufacture.
- The RESETTABLE LAMP ON counter is user-resettable and displa ys the n umber of hours the lamp
has been powered on since the counter was last reset.
LAMP STRIKES provides two counters:
- The TOTAL LAMP STRIKES counter is not user-resettable and displays the total number of lamp
strikes since manufacture.
- The RESETT ABLE LAMP STRIKES counter is user-resettable and displa ys the number of lamp strikes
since the counter was last reset.
AIR FILTERS provides an alert feature for service interventions:
- The RESETTABLE AIR FILTER counter displays the total number of hours the fixture has been
powered on since the alert timer was last cleared.
- SET TIME ALERT lets you set the number of hours from 1 to 750 you want the fixture to be powered on
before a service alert appears in the display. If you set this figure to 0, the time alert is disabled.
- CLEAR RESETTABLE AIR FILTER lets you reset the resettable air filter counter to zero after
completing service work.
FIXTURE MAC ID displays the fixture’s factory-set MAC (Media Access Control) address.
RDM UID displays the fixture’s factory-se t unique ID for identification in RDM systems.
FANS SPEED provides separate status readouts from the fixture’s cooling fans.
TEMPERATURE provides a fixture temperature status readout.
POWER UNIT provides the following readouts:
- MAINS VOLTAGE displays a mains power voltage readout
measured at the fixture’s mains power input.
- LAMP VOLTAGE, LAMP CURRENT and LAMP WATTAGE
display readouts measured at the fixture’s lamp terminals.
- LAMP STATE gives a lamp status readout.
- IGNITER STATE gives an igniter (starter) lamp status
readout.
- INTENSITY indicates current lamp intensity.
EVENT LOG VIEWER lets you view event logs in the fixture’s display panel. See “Event log” on page 34.
Control panel operations 19
Page 20

DMX signal monitoring

The MAC III Performance provides data on the DMX signal it is receiving in the DMX LIVE menu. This information can be useful for troubleshooting control problems.
RATE displays the DMX refresh rate in packets per second. Values lower than 10 or higher than 44 may result in erratic performance, especially when using tracking control.
QUALITY displays the quality of the received DMX data as a percentage of packets received. Values much below 100 indicate interference, poor connections, or other problems with the serial data link that are the most common cause of control problems.
START CODE displays the DMX start code. Packets with a start code other than 0 may cause irregular performance.
The remaining options under DMX LIVE display the DMX values in a range from 0 - 255 that are being received on each channel. The DMX channels shown will depend on whether the fixture is in 16-bit or 16-bit extended mode.

Test sequence

TEST SEQUENCE activates effects in sequence, allowing you
to test them quickly without a DMX controller:
ACTION lets you star t, pause, and stop the sequence. TYPE lets you test all effects, pan/tilt movement only, or the
other effects only. REPEAT sets the current test to repeat when finished. Status readouts for the current test sequence are displayed
below the ACTION, TYPE and REPEAT commands.

Manual control

The MANUAL CONTROL menu lets you reset the fixture, strike our douse the lamp, apply effects and move pan and tilt manually.

Setup Wizard menu

The SETUP WIZARD menu gives quick access to the most frequently required items in the control menus.
20 MAC III Performance user manual
Page 21

Adjusting settings via DMX

Certain fixture settings and parameters ca n be adjusted from the DMX controller on DMX channels 33 and 34 in 16-bit mode or channels 39 and 40 in 16-bit extended mode.
Commands sent via DMX override any settings entered in the fixture’s onboard control menus. However, to reset the fixture, reset individual effects or cut power to the lamp via DMX if DMX Reset or DMX Lamp Off are disabled in the control menus, the following conditions must be met:
• Slot 1 must be selected on the color wheel (DMX value 20 on channel 8 in 16-bit mode or 9 in 16-bit extended mode),
• the beam effect (frost as standard) must be on (DMX value 20-59 on channel 24 in 16-bit or channel 28 in 16-bit extended mode), and
• open gobo must be selected on the gobo wheel (DMX value 0 on channels 8 and 9 in 16-bit or channels 9 and 10 in 16-bit extended mode).
Note also that a lamp off command sent by DMX must be applied for 5 seconds before it executes. These requirements are a safeguard to help you avoid resetting the fixture or powering the lamp off
accidentally.

Resetting

Either the entire fixture or individual effects can be reset to their initial positions. Resetting individual effects can allow on-the-fly recovery if an effect loses its correct position, for example, without having to reset the entire fixture.

Lamp on / off

The lamp can be struck and doused from the DMX controller. A peak of electric current that is many times the operating current is drawn for a fraction of a second when
striking a discharge lamp. Striking many lamps at once may cause a voltage drop large enough to prevent lamps from striking or draw enough current to trip electronic circuit breakers. If sending lamp-on commands to multiple fixtures, program a sequence that strikes lamps one at a time.

Adjusting lamp power

If full light output is not required, the power supplied to the lamp by the ballast can be reduced. Reducing lamp power reduces heat output and therefore reduces noise from the cooling fans. It also reduces power consumption, and it helps reduce the gradual fall in output that occurs over the lifetime of a discharge lamp.
Lamp power can be to set to 1500 W (full power), 1200 W, 1100 W, 1000 W or 900 W via DMX using the ballast output control commands available on channel 26 (16-bit) or 29 (16-bit extended).
If the shutter and/or dimmer are closed for longer than 10 seconds, lamp power is automatically switched to 900 W. When the shutter is opened again, the lamp returns to full power.

Illuminating the display

The fixture’s display panel can be brought out of sleep mode with a DMX command. This makes it possible to read the fixture’s DMX address while the fixture is installed in the rig.
After being illuminated in this way, the display will return to sleep mode according to the setting entered in the onboard control menus.

Control menu setting overrides

The following fixture settings can be adjusted via DMX, overriding the settings entered in the onboard control menus. See under “Control panel operations” on page 14 for details of these parameters.
• Dimming curve
• Parameter shortcuts
Adjusting settings via DMX 21
Page 22
• Zoom/focus linking
• Pan/tilt limits
• Calibration offsets
Defining calibration offsets via DMX
The ”Fixture adjustments/calibration” DMX channel allows effect offsets to be adjusted and stored in the fixture from the DMX controller.
To adjust an effect offset:
1. Set the effect to a DMX value from 0 to 255 on its own
DMX channel (for example, set Cy an to 192 on channel 3 in 16-bit mode or 4 in 16-bit extended mode).
2. Send a ‘Store’ command for the effect on the Fixture
Adjustment/Calibration channel (for example, send DMX value 130-134 on channel 34 in 16-bit mode or channel 40 in 16-bit extended mode to store the Cyan adjustment).
The MAC III Performance now reads the value on the effect channel (192 for Cyan in the example above), translates it to an adjustment value of between -5% and +5% as shown in Figure 12 (+2.5% Cyan adjustment in the example above) and stores that offset in memory.
See ”Fixture adjustments/calibration” in the DMX protocol on page 54 for details of the offsets that can be adjusted using this method.
Effect offsets stored in memory are not affected by powering the fixture off and on or by updating the fixture software. To return all offsets to their factory defaults, send a DMX value from 245 to 249 on the ”Fixture adjustments/calibration” channel 34 (16-bit mode) or 40 (16-bit extended mode) or apply LOAD FACTORY SETTINGS in the FACTORY SETTINGS menu in the fixture’s control panel.
255
192
128
64
0
Effect channel
value
Figure 12: Offset adjustment values
+5%
+2.5%
0
-2.5%
-5%
Adjustment
value
22 MAC III Performance user manual
Page 23

Effects

This section gives details of the effects that can be controlled via DMX. See “MAC III Performance DMX protocol” on page 47 for details of the channels used to control them.
Where fine control is available, the main control channel sets the first 8 bits (the most significant byte or MSB), and the fine channels set the second 8 bits (the least significant byte or LSB) of the 16-bit control byte. In other words, the fine channel works within the position set by the coarse channel.

Shutter and strobe effects

The MAC III Performance’s mechanical shutter provides regular or random strobe and pulse effects with variable speed from 2 Hz to 10 Hz approximately.
To ensure total blackout, the mechanical dimmer also deploys if the shutter is closed for more than 5 seconds.

Dimming

The MAC III Performance’s mechanical dimmer provides smooth, high-resolution 100 percent fading. Fine control of the dimmer is available in 16-bit extended mode. To ensure total blackout, the mechanical shutter also deploys if the dimmer is reduced to 0% for more than 5
seconds.

Cyan, Magenta, Yellow and CTO

The amount of cyan, magenta, yellow and CTO (color temperature control orange) applied to the MAC III Performance’s light output can be varied from zero to 100%. Color temperature can be varied from 6000 ­3200 K.

Color wheel

The MAC III Performance features a color wheel with 7 interchangeable dichroic color filters and an open position. Color filters can be applied as split colors or in full-color steps. The color wheel can also be scrolled continuously, applying the color filters in sequence with control of color wheel speed and direction. Color filters can also be applied at random at fast, medium or slow speed.
As standard the MAC III Performance is supplied with the following color filters:
• Slot 1 - Blue 101 - P/N 46404500
• Slot 2 - Green 203 - P/N 46404510
• Slot 3 - Orange 311 - P/N 46404520
• Slot 4 - Minus green - P/N 46404540
• Slot 5 - Yellow 610 - P/N 46404530
• Slot 6 - Congo - P/N 46404550
• Slot 7 - Red 310 - P/N 46404560
• Slot 8 - Open
The DMX Protocol on page 47 gives details of color filter selection.

Rotating gobos

The rotating gobo wheel in the MAC III Performance provides 5 rotating gobos plus an open position. The standard gobos are shown in the correct order in Figure 13.
Gobos can be selected, indexed (positioned at an angle), rotated continuously, and shaken (bounced). The gobo wheel can also be scrolled continuously or shaken. Indexing, continuous gobo rotation, gobo shake and continuous gobo wheel scrolling are selected on one channel. Depending on what is selected on this
Effects 23
Page 24
first channel, the indexed angle or rotation speed are set on the next channel. If gobo indexing is selected on the first channel, fine control of gobo index angle is available on the third gobo wheel control channel in both 16-bit and 16-bit extended modes.
Crossfading speed between rotating gobos can be set on channel 21 (in 16-bit) or 25 (in 16-bit extended mode).
All gobos are interchangeable, but replacement gobos must match the dimensions, construction and quality of the gobos supplied as standard (see under “Specifications” on page 65).
Handling, installing and storing the gobos in the MAC III Performance requires special care. See “Gobos in the MAC III Performance” on pa ge 42 for details.
1
1. Leaf breakup (medium).........P/N 43042060
5
2. Dot breakup...........................P/N 43042061
3. Limbo (with holder)................P/N 62325128
4. Linear 3 .................................P/N 43042062
5. Raytraces..............................P/N 43042063
2
4
Gobo wheel viewed from front lens

Gobo animation

The gobo animation system lets you create animated effects by rotating the animation wheel and masking the resulting pattern with a gobo.
The system uses two channels:
• On the first channel, you set the animation wheel so that its pattern is horizontal, vertical or set at an indexed angle, with the animation wheel either static or rotating.
• On the second channel, you can either set the indexed angle of the animation wheel pattern (if you have set the animation wheel to a static position on the first channel), or set the animation wheel direction and speed (if you have selected rotation on the first channel).
When projecting onto a surface or stage, setting the pattern to horizontal with very slow rotation can simulate windswept clouds, for e xample , and setting the pattern close to vertical with faster rotation can simulate flames. Adjust the fixture’s focus to obtain the most realistic results.
The animation wheel can also give mid-air and linear projection effects that are different from rotating gobo effects in that they do not rotate around a center axis.
3
Figure 13: Rotating gobos installed as standard
24 MAC III Performance user manual
Page 25
Animation wheel
The MAC III Performance is supplied with the “Tribal waves” gobo animation wheel (P/N 62325143) installed. See under “Specifications” on page 65 for full specifications for this component. Additional stock patterns will be available as accessories from Martin dealers.

Beam effect (frost)

The MAC III Performance is fitted with a frost filter that can be applied to or removed from the beam remotely.
If preferred, the frost filter can be replaced with the four-facet prism (available as an accessory: P/N
62329120) installed as standard in MAC III Profile fixtures. The prism can be applied at indexed angles or
rotated with variable direction and speed.

Iris

The iris can be set to a static diameter, or regular and random pulsing effects can be set with variable speed.

Focus and zoom

The focus lens focuses the beam from approximately 2 meters (6.5 feet) to infinity. The separate zoom lens varies the focused beam angle from 11.5° to 55° with the standard lens installed.
Zoom/focus linking
Focus can be linked to zoom so that it automatically adjusts to match changes in zoom angle. Focus on rotating gobos matches zoom closely, while focus on the gobo animation wheel matches zoom best in the center of the zoom range and slightly less precisely at the two extremes of the zoom range.
Linked zoom/focus works within 3 distance ranges:
• Near (5 - 10 meters)
• Medium (10 - 20 meters)
• Far (20 meters - infinity)
To link zoom and focus, select a distance range using the Fixture Control/Settings DMX channel or FOCUS TRACKING in the PERSONALITY menu in the control panel. Then adjust focus to obtain the required degree of sharpness. Linking is now enabled and focus will auto-adjust.
Figure 14: Tribal waves gobo animation wheel
Effects 25
Page 26

Pan and tilt

Coarse and fine pan and tilt control are available in both 16-bit and 16-bit extended modes. Maximum and minimum pan and tilt limits can be set using the control panel (see “Personality – tailoring
performance” on page 16) and via DMX.

Rotating Framing

The 4-blade framing module in the MAC III Performance can be held static or rotated continuously with variable speed. It can form the beam into any shape with three or four sides and morph between shapes.
Framing macros
If the fixture is set to 16-bit extended mode, a number of framing macros can be selected on DMX channel
22. These macros are pre-programmed framing effects with quick access via DM X.
Macro 1
Vertical bar
Macro 6
Trapezoid Up
Macro 11
Equilateral Triangle
Left
Macro 16
Right-angle Triangle
Up Right
Macro 2
Horizontal bar
Macro 7
Trapezoid Left
Macro 12
Equilateral Triangle
Down
Macro 17
Right-angle Triangle
Up Left
Macro 3
Square
Macro 8
Trapezoid Down
Macro 13
Equilateral Triangle
Right
Macro 4
Parallelogram Right
Macro 9
Trapezoid Right
Macro 14
Right-angle Triangle
Down Left
Macro 5
Parallelogram Left
Macro 10
Equilateral Triangle
Up
Macro 15
Right-angle Triangle
Down Right
Table 2: Framing shape macros
The size of the framing macro and crossfading speed between macro shapes can be adjusted via DMX on channels 23 and 24 in 16-bit extended mode.
When a framing macro is selected, the eight individual frame position and angle channels from 11/12 to 18/19 and the macro size channel 23 (in 16-bit extended mode) act as offsets that can modify the macro shape and size. These channels must be at DMX value 128 for the basic macro shape to be displayed.
Note that an offset applied to a framing macro using any of these channels will not respond to crossfading times set on channel 24 in 16-bit extended mode. To adjust crossfading speed when the basic macro shape has been modified, channel 24 must be set so that macro crossfading speed follows console timing, and crossfading speed must be set on the console.
26 MAC III Performance user manual
Page 27

Followspot mode

The MAC III P erformance fixture software from version 1.6.0 features a follo wspot mode in which the fixture ignores any pan, tilt, or pan and tilt commands sent via DMX or the control menu, releasing the head for use as a followspot.
In followspot mode, the pan and/or tilt motors can be engaged or disengaged from the control menu as a brake to pan, tilt, or both pan and tilt movement to prevent the head from moving when it is not being held in place. in this case DMX or menu-based control over pan and tilt is still disabled (see “Personality – tailoring performance” on page 16 and “Control panel menus” on page 55).
Followspot handles can be custom-made by the user to suit the user’s own preferences and requirements.
Followspot handles safety precautions
Warning! It is the user’s responsibility to ensure that the followspot handles and any mounting brackets are safe and that the fixture is kept in followspot mode at all times while handles are installed to avoid collision between the followspot handles and the yoke.
Warning! Intermediate brackets for permanent mounting on the back of the MAC III Performance head must be constructed so that they will not touch the yoke at any point in the head’s tilt range!
Warning! Screws used to fasten any item to the rear of the head may only be fastened into the holes (arrowed in Figure 15) provided in the rear head cover. Do not attempt to fasten any item to the rear of the head by any other method. Screws must not protrude more than 15 mm (0.6 inches) into the rear head cover, or there is a danger that they may damage electrical insulation inside the head and create a risk of serious or lethal electric shock for the operator.
Warning! Followspot handles must be thermally insulated so that it is impossible f or the operator to suffer discomfort or a burn injury.
Followspot handles use and construction
The MAC III Performance’s rear head cover is a magnesium alloy casting. Magnesium alloy is prone to galvanic corrosion when steel screws are fastened into it and has a relatively low resistance to mechanical wear on threads. Self-tapping screws fastened into magnesium alloy should be left there perm anently.
If you are going to switch between using the MAC III Performance as a manually-controlled followspot and as a DMX-controlled moving head from time to time, you will need to install and remove followspot handles. In this case, we recommend that you fabricate two intermediate mounting brackets in a suitable material for repeated installation and removal of screws, fasten the brackets permanently to the rear head cover, and use these brackets as mounting points for the followspot handles.
If followspot handles are going to be installed permanently, there is no need for intermediate brackets. The design of the brackets and followspot handles is left up to the user to match user requirements, but the
following points must be noted:
• Intermediate mounting brackets must be as light as possible in order to minimize the effect of their extra weight on the balance of the head. It may be best to make them in aluminium.
• Four holes (arrowed in Figure 15) are provided in the fixture’s rear head cover for fastening followspot handle mounting brackets.
• On most MAC III Profile fixtures manufactured before August 2009, the four holes are drilled but not threaded. If you have reconfigured a MAC III Profile as a MAC III Performance, check these holes. If they are not threaded, use M6 thread-forming screws (DIN 7500) to fasten mounting brackets. Torx head screws are recommended because considerable force will be required to tighten the screws into the rear cover. If the four holes are threaded, use regular M6 machine screws for attachment.
Effects 27
Page 28
• Whatever type of screw used, the portion of the screw that goes into the rear head cover must have a length of between 12 mm (0.47 in.) and 15 mm (0.6 in.).
• The rear head cover becomes very hot. Ensure that handles are insulated well enough to avoid discomfort or burn injuries for the followspot operator.
• A handle must only be fitted after followspot mode is enabled and tilt is performed manually. Always remove any handle that is fitted before disengaging followspot mode.
Besides being constructed so that they will not foul the yoke at any point in the tilt range, mounting brackets must match the dimensions shown in Figure 15.
Dimensions in Figure 15 are shown in millimeters:
• 216.8 mm = 8.53 in.
• 230.7 mm = 9.08 in.
• 78.9 mm = 3.11 in.
Figure 15: Dimensions for followspot handles
28 MAC III Performance user manual
Page 29
RDM
The MAC III Performance can communicate using RDM (Remote Device Management) in accordance with ESTA’s American National Standard E1.20-2006: Entertainment Technology RDM Remote Device Management Over DMX512 Networks.
RDM is a bi-directional communications protocol for use in DMX512 control systems, it is the open standard for DMX512 device configuration and status monitoring.
The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely affecting existing non-RDM equipment. The RDM protocol allows a console or dedicated RDM controller to send commands to and receive messages from specific fixtures.

RDM port

In line with the RDM standard, the MAC III Performance running firmware version 1.6.0 or later uses Port 1 for both RDM and DMX signals. We recommend that MAC III Performance users running earlier firmware upgrade to the latest available version; see “Software installation” on page 38.

RDM ID

Each MAC III Performance has an RDM UID that makes it uniquely addressable. This can be found in the control panel menus under FIXTURE INFORMAT ION. RDM UID shows the fixture’s factory-set unique ID for identification in RDM systems.

RDM communication

The MAC III Performance running firmware version 1.6.0 or later will respond to:
1. ”MAC III Performance supported standard commands”; see page 30.
2. ”MAC III Performance supported manufacturer specific commands”; see page 31.
The parameter IDs listed here are described in the Martin RDM User Reference Guide (P/N 35000234), only available online from the Martin website at http://www.martin.com mid-2010.
RDM 29
Page 30
MAC III Performance supported standard commands
GET
allowed
9 QUEUED_MESSAGE 9 STATUS_MESSAGES 9 STATUS_ID_DESCRIPTION
9 SUPPORTED_PARAMETERS 9 PARAMETER_DESCRIPTION
9 DEVICE_INFO 9 DEVICE_MODEL_DESCRIPTION 9 MANUFACTURER_LABEL 99DEVICE_LABEL 99FACTORY_DEFAULTS 9 SOFTWARE_VERSION_LABEL
99DMX_PERSONALITY 9 DMX_PERSONALITY_DESCRIPTION 99DMX_START_ADDRESS 9 SLOT_DESCRIPTION
9 SENSOR_DEFINITION 99SENSOR_VALUE
99DEVICE_HOURS 99LAMP_HOURS 99LAMP_STRIKES 99LAMP_STATE 99LAMP_ON_MODE 99DEVICE_POWER_CYCLES
99DISPLAY_INVERT 99DISPLAY_LEVEL
99PAN_INVERT 99TILT_INVERT 99PAN_TILT_SWAP
99IDENTIFY_DEVICE
99PERFORM_SELFTEST 99SELF_TEST_DESCRIPTION
SET
allowed RDM parameter ID’s (slot 21-22) Notes
Category – Network Management DISC_UNIQUE_BRANCH DISC_MUTE DISC_UN_MUTE Category - Status Collection
9 CLEAR_STATUS_ID
Category - RDM Information
Category – Product Information
Category - DMX512 Setup
Category – Sensors See “RDM accessible onboard sensors” on page 31
Category – Dimmer Settings Reserved for future use Category – Power/Lamp Settings
Category - Display Settings
Category – Configuration
Category – Control
9 RESET_DEVICE
30 MAC III Performance user manual
Page 31
RDM accessible onboard sensors
The following onboard sensors are RDM accessible:
LAMP R FAN LAMP L FAN BOTTOM FAN
FAN SPEED
TEMPERATURE
POWER UNIT
CMY FAN TOP FAN MAINBOARD FAN POWER FAN 1 POWER FAN 2 UI PCB CHARGER PCB BATTERY FAN PCB ANIMATION FX PCB GOBO FX PCB CMY PCB ZOOM FOCUS PCB PAN/TILT PCB POWER UNIT PCB POWER UNIT CAPACITOR MAINS VOLTAGE LAMP VOLTAGE LAMP CURRENT LAMP WATTAGE
MAC III Performance supported manufacturer specific commands
GET
allowed
99DMX_LAMP_OFF 99DMX_RESET
99EFFECT_SPEED 99EFFECT_SHORTCUTS 99LAMP_HOUR_WARNING_HOURS Data range is 0 - 750 hours 99AIR_FILTER_HOUR Data range is 0 - 750 hours 99AIR_FILTER _HOUR_WARNING_HOURS Data range is 0 - 750 hours 99DIMMER_CURVE 99FOCUS_TRACKING 99DISPLAY_AUTO_OFF
99PAN_TILT_SPEED 99PAN_TILT_MOVE_ON_RESET 99PAN_TILT_LIMITATION 99PAN_LIMITATION_MINIMUM 99PAN_LIMITATION_MAXIMUM 99TILT_LIMITATION_MINIMUM 99TILT_LIMITATION_MAXIMUM 99PAN_TILT_LIMITATION_AREA
SET
allowed RDM parameter ID’s (slot 21-22) Notes
Category – DMX protocol settings
Fixture behavioral settings
Fixture pan/tilt settings
Fixture followspot settings
RDM 31
Page 32
99FOLLOW_SPOT_MODE
9 FOLLOW_SPOT_MODE_LOCK_TOGGLE 99FOLLOW_SPOT_MODE _LOCK_PAN 99FOLLOW_SPOT_MODE _LOCK_TILT
Fixture cooling settings
99LAMP_COOLING 99FAN_CLEAN 99FAN_MODE
Fixture other settings
9 SERIAL_NUMBER
9 LICENSE_KEY
9 EVENT_LOG_USER_EVENT_TRIGGER
32 MAC III Performance user manual
Page 33

Service and maintenance

Warning! Disconnect the fixture from power and allow to cool for 2 hours 45 minutes before removing any cover.
Important! Excessive dust, smoke fluid, and particulate buildup degrades performance, causes overheating and will damage the fixture. Damage caused by inadequate maintenance is not covered by the warranty.
This section lists service and maintenance operations that may be carried out by the user. Refer any operation that is not described here to a qualified Martin technician.
The MAC III Performance requires routine cleaning. The schedule depends heavily on the operating environment. It is essential to follow the cleaning guidelines given later in this section.

Tilt lock

Important! Release the tilt lock before
operating the fixture.
The tilt position of the head can be locked at various angles for service. Push the lock in towards the yoke in one direction to lock the head and back in from the other side to unlock the head.
There is no pan lock on the MAC III Performance.
Important! Release the tilt lock before
packing the fixture in the flightcase.
Figure 16: Tilt lock

Service utilities

The SERVICE menu in the main menu provides utilities for technicians rigging or servicing the fixture:
PAN/TILT FEEDB ACK lets you disable feedback to the fixture software from the pan, tilt and effects positioning systems. If feedback is set to On and a pan, tilt or effect position error is detected, the shutter closes and the effect resets. This feature can be disabled by setting feedback to Off. The Off setting is not saved when the fixture is powered off, and the system will be re-enabled the next time the fixture starts. If a pan/tilt position error occurs and the system cannot correct pan/tilt position within 10 seconds, feedback is automatically disabled.
ADJUST is for use at the factory and by authorized Martin Service technicians only. This menu allows dimmer, shutter, pan and tilt positions to be adjusted after replacement of components, etc. To adjust the default positions of all the MAC III Performance’s eff ects, use the CALIBRATION menu instead.
Important! Do not enter the ADJUST menu without service documentation from Martin.
• CALIBRATION sets effects to their factory default positions or lets you set new default positions for calibration purposes. See ”Calibrating effects” later in this chapter for full details.
UPDATE FIRMWARE, updates the firmware (fixture software). For a detailed guide to updating the firmware, see ”Software installation” later in this chapter.
• EVENT LOG gives access to the fixture’s log. See next section.
Service and maintenance 33
Page 34

Event log

The MAC III Performance from software version 1.5.0 monitors performance, any errors or warnings, temperatures, etc. and stores data in an ongoing service event log that can be viewed in the fixture’s displa y or downloaded to a USB memory device and viewed on a PC.
Power cycle reports are created automatically each time the fixture is powered up. The fixture stores up to 25 power cycle reports in memory. If the memory is full, the oldest report is deleted each time a new report is generated.
A power cycle report lists three types of data:
1. General data, settings 2. Events 3. Dynamic Content
General data, settings displays fixture information and lists current settings. Events is only displayed if any warnings, errors or changes in settings occur, and lists these with the
amount of time that has passed since they occurred. Dynamic content displays technical data for the fixture that is intended to help troubleshooting. It is only
displayed if warnings or errors are listed in the Events section. Dynamic content is updated automatically with current data — and the old data is saved to the event log — every 15 minutes for up to 10 hours. The oldest data is then replaced by new data. If an error or warning occurs, data is updated immediately. Dynamic content can also be updated manually. This can be useful if a fixture does not behave as e xpected, for example, b ut the fixture is not showing an error or a warning. the user can check that the DMX start code is zero to eliminate poor data transmission as a possible cause of the problem. To renew the dynamic content in the current power cycle report with the current data:
•select SERVICE
•select Event log trigger by sending DMX value 250-255 on DMX channel 26 (in 16-bit basic mode) or 29
• send the RDM command EVENT_LOG_USER_EVENT_TRIGGER.
To delete all previous power cycle reports in the event log from memory, select SERVICE EVENT LOG Clean Event Log in the control panel.
General Information Personality Settings Adjust Settings Calibration Settings Fixture Information Module Information PCB Information
EVENT LOG EVENT LOG TRIGGER in the control panel, or
(in 16-bit extended mode), or
Errors, warnings, changes in settings
Fan speeds Temperatures Other data
Viewing the event log in the fixture’s display panel
To view the event log in the fixture’s display panel, select FIXTURE INFORMATION control panel.
The EVENT LOG VIEWER displays all the power cycle reports in memory and supplementary information about any event you scroll to. Use the jog wheel to scroll through the power cycle reports. As you scroll and highlight each event, details of the event are shown at the bottom of the display:
TIME gives the time after power up that the event occurred.
DESCRIPTION gives type of event.
VALUE gives either the value of a new personality setting (e.g. On/Off) or the long description of an error code (e.g. FOER = focus error).
EVENT LOG VIEWER in the
Viewing power cycle reports on a PC
To view the current and most recent power cycle reports on a PC:
1. Insert a USB memory device in the fixture’s USB port to open the USB device pop-up window.
2. Select Download Event Log and wait for the log file to be saved to the USB device.
3. Remove the USB memory device, and carry out this procedure with other fixtures if required.
34 MAC III Performance user manual
Page 35
4. Connect the USB memory device to a PC. Logs are stored in the root directory of the memory device in
a folder called EVENT LOGS MAC III SERIES using the naming convention LOG MACIII XXXXXXXXXX.xml (where XXXXXXXXXX is the serial number of the fixture). The XML files can be viewed using any web browser that supports XSLT 1.0 such as Internet Explorer 6, Firefox 3, Google Chrome 1, Opera 9, Apple Safari 3 or later versions.
5. Double-click on the event log to open it in your web browser.
Event log structure when viewed in a web browser
The title Power Cycle is displayed in red if that power cycle report includes an error. Event log XML files are divided into boxes:
General information lists the most important information held by the fixture.
Personality Settings lists the fixture’s settings at power up.
• Adjustment Settings displays the fixture’s factory adjustment settings at power up. These settings should only be changed by Martin Service or its authorized agents.
• Calibration Settings displays the fixture’s calibration settings at power up. These settings can be changed by the user (see “Calibrating effects” on page 37).
Service and maintenance 35
Page 36
• Fixture Information displays data from the fixture’s timers when it was last powered up.
• Module Information displays data from the fixture’s effects modules.
• PCB information displays data from the fixture’s PCBs.
The Event Section lists all the errors, warnings and setting changes carried out by the user since the last po wer cycle in the event log. The Time column on the left of the box displays the amount of time between the fixture powering up and the event. Thus, in the example on the right, a main PCB fan error occurred 2 minutes and 7 seconds after power up and the pan/tilt sensor was not calibrated (warning was listed as ACTIVE) 1 minute and 24 seconds after power up but was calibrated (warning was listed as INACTIVE) 8 minutes and 48 seconds after power up.
Dynamic Content displays the speed of the fixture’s fans , fixture temperatures and other data:
- current data (in the
example on the right, two minutes and one second after power up).
- previously logged data
(captured at 15-minute intervals over a tot al of u p to 10 hours, most recent data at the top — see following example showing time).
36 MAC III Performance user manual
Page 37
The example below in the Dynamic Content section, shows temperature data for the different sensors in the fixture. In the example, the fixture was powered on 3 hours and 15 minutes before the current temperature data was logged. Temperature change over ti me at 15 minute intervals can be followed in the table. If you wish, it can also be copied and pasted into spreadsheet software such as Microsoft Excel.
Handling XML log files
The XML event log files can be archived and e-mailed, but you must include the folder templates and its contents MACIII_EventLog.css and MACIII_EventLog.xsl in the same folder as the XML files so that web browsers can view the event logs correctly:
Zipping the EVENT LOGS MAC III SERIES folder before storing or sending should ensure that the nested
templates folder is correctly included.

Calibrating effects

The CALIBRATION menu lets you define offsets in software that are relative to the mechanical reset or home positions. This allows you to fine-tune optical alignment and achieve uniform performance between fixtures. Fixtures are calibrated at the factory, and further calibration will normally only be necessary if fixtures have been subjected to abnormal shocks during transport or if norm al wear and tear has affected alignment after an extended period of use.
Calibrating pan and tilt sensors
When you select PAN/TILT SENSOR CALIBRATION, a display message appears asking you to move pan and tilt to their end stop positions. To calibrate pan and tilt:
1. Move pan to its end stop position by rotating the yoke
clockwise (as seen from above the head looking down at the base) to maximum pan.
2. Move tilt to its end stop by tilting the head to its maximum
angle with the front glass pointing away from the display panel.
3. Press the jog wheel to register the positions. The fixture
will display Saving...
Warning! As soon as you exit pan/tilt sensor calibration, the head will move to its original position.
Service and maintenance 37
Page 38
4. Make sure that you are ready for the head to move , then press the Escape button to exit pan/tilt sensor
calibration. The head will now pan and tilt back to where it was before you entered calibration mode.
Calibrating effects
Calibration can be carried out via DMX (see “Defining calibration offsets via DMX” on page 22) but the easiest approach is probably to set multiple fixtures to the same position (e.g. dimmer open 1%) and then calibrate each fixture using its onboard control panel while comparing its light output with a reference fixture.
The calibration range available for each eff e ct varies but is approx 5%. After selecting a calibration value, click on the jog wheel to set the effect to that value.
Loading and storing default calibration offsets
LOAD DEFAULTS? lets you load the factory default calibration offsets stored in memory. SA VE FACT ORY DEFAULT? lets you overwrite the factory default calibration offsets stored in memory with
any new offsets you have defined. Overwriting is permanent, so once you have saved new factory default offsets, LOAD DEFAULTS? will reload the new offsets.

Software installation

The currently installed firmware (fixture software) version can be viewed under FIXTURE INFORMATION in the main menu. Firmware updates are available from the Martin website and can be installed using either of two methods:
• a USB memory device loaded with ‘bank’ files and inserted in the MAC III Performance’s USB port, or
• a Windows PC loaded with ‘MU3’ files and running the Mar tin Uploader application, connected to the MAC III Performance’s data input socket via a Martin Universal USB/DMX™ or a Martin DABS1™ hardware interface.
Installing using a USB memory device
The following are required in order to install firmware using a USB memory device:
• The MAC III Performance fir m ware ‘bank’ update file, available for download from the Product Support area of the Martin website at http://www.martin.com.
• A USB memory storage device (e.g. USB stick) with the update file copied from a PC into the memory device’s root directory.
To install the MAC III Perfor mance firmware:
1. Download the firmware ‘bank’ from the MAC III Performance support page on the Martin website at
www.martin.com, read the firmware release notes carefully to check for any instructions or warnings, and copy the ‘bank’ to the root directory of a USB memory stick.
2. Disconnect the data link from the MAC III Performance.
3. Insert the USB stick in the MAC III Performance’s USB host
socket. The fixture should recognize the USB stick, illuminate the display panel and show the UPDATE FIRMWARE window in the display. Alternatively, scroll to the UPDATE FIRMWARE menu under SERVICE in the control panel.
4. Select BANK. Scroll up and down to see the firmware
versions present on the USB stick and in the fixture’s internal memory. LOCATION indicates whether the firmware is located on the USB stick or in internal memory.
5. If you scroll to a firmware version on the USB stick and click
the jog wheel, the firmware is downloaded to internal memory (where it will be available for future firmware updates), validated, unpacked and installed, and the fixture will restart using the new firmware.
6. Remove the USB stick. The newly-installed firmware version will now be displayed in the FIXTURE
INFORMATION menu.
38 MAC III Performance user manual
Page 39
7. Reconnect the data link.
Zoom-focus linking is reset to default (medium distance) when new software is uploaded. Other fixture information and settings are unaffected.
Forced upload
The fixture can be forced to automatically upload a software fi le from a USB stick if the Escape button is held down during power up. We recommend that only one software update file is located in the memory device’s root directory, but in the event that several versions are available, the fixture will upload the file with the most recent software version.
Installing using a PC and hardware interface
The following are required in order to install firmware using a PC and hardware interface:
• The MAC III Performance fir m ware ‘MU3’ update file, available for download from the Product Support area of the Martin website at http://www.martin.com.
• A Windows PC running the latest version of the Martin Uploader™ application (also available for download free of charge from www.martin.com) and loaded with the firmware update file.
• A USB/DMX hardware interface device such as the Martin Universal USB/DMX™ or Martin DABS1™.
To install the MAC III Perfor mance firmware:
1. Download the firmware ‘.MU3’ file from the MAC III Performance support page on the Martin website at
www.martin.com to the PC.
2. Read the firmware release notes carefully to check for any instructions or warnings.
3. Follow the instructions for an auto upload/upload via DMX in the Martin Uploader application help files
and supplied with the hardware interface.

Cleaning

Regular cleaning is very important for fixture life and performance. Buildup of dust, dirt, smoke particles, fog fluid residues, etc. degrades the fixture’s light output and cooling ability.
Cleaning schedules for lighting fixtures vary greatly depending on the operating environment. It is therefore impossible to specify precise cleaning intervals for the MAC III Performan ce . Coo ling fans suck in airborne dust and smoke particles, and in extreme cases fixtures may require cleaning after surprisingly few hours of operation. Environmental factors that may result in a need for frequent cleaning include:
• Use of smoke or fog machines.
• High airflow rates (near air conditioning vents, for example).
• Presence of cigarette smoke.
• Airborne dust (from stage effects, building structures and fittings or the natural environment at outdoor events, for example).
If one or more of these factors is present, inspect fixtures within their first 25 hours of operation to see whether cleaning is necessary. Check again at frequen t intervals. This procedure will allow you to assess cleaning requirements in your particular situation. If in doubt, consult your Martin dealer about a suitable maintenance schedule.
Use care when cleaning optical components and work in a clean, well lit area. The coated surfaces are fragile and easily scratched. Do not use solvents that can damage plastic or painted surfaces.
Service and maintenance 39
Page 40
Cleaning and replacing the air filters
The item AIR FILTERS in the FIXTURE INFORMA T ION menu is intended to be used to monitor intervals between air filter cleaning, although this counter can be used to monitor any aspect of the fixture.
When air filters require cleaning:
1. Disconnect the fixture from power and allow
the components to cool for 2 hours 45 minutes.
2. See Figure 17. On each side of the head, use
a flat-bladed screwdriver to lever the front edge of each filter holder away from the head and pull the filter holders forwards to unclip and remove them.
Figure 17: Removing head air filters
3. See Figure 18. On each side of the base,
pinch the air filter holders in from the sides as illustrated, then pull the center of the holders outwards to unclip and remove them.
4. Clean the air filter elements. If they are saturated with smoke
fluid, soak them in warm, soapy water and blot dry . If the filters cannot be cleaned completely or are not in perfect condition, replace them with new items.
5. Pinch the base filter holders in from the side and engage the
ends of the filter holders their slots to clip them back into position.
6. See Figure 19. Engage the three tabs in the head filter
holders in their slots in the head, pinch the foremost corners of the filter holder together slightly and press them into the head to clip them back into position.
7. Check that all fil ter holders ar e correctly insta lled so that there
is an airtight seal around all their edges.
Figure 18: Base air filters
Figure 19: Reinstalling head air filters
40 MAC III Performance user manual
Page 41
Cleaning the fixture
To clean the head:
1. Disconnect the fixture from power and allow the components to cool for
2 hours 45 minutes.
2. Remove both head covers by loosening their quarter-turn retaining
screws (see Figure 20).
3. Vacuum or gently blow away dust and loose particles inside the head
with compressed air.
4. Carefully clean the optical components, but note that special precautions
apply to the gobos (see “If no further service work is to be carried out, reinstall the top cover with its safety wire and release the tilt lock.” on page 41). Remove smoke and other residues with cotton swabs or unscented tissues moistened with isopropyl alcohol. A commercial glass cleaner may be used, but residues must be removed with distilled water. Clean with a slow circular motion from center to edge. Dry with a clean, soft and lint-free cloth or compressed air. Remove stuc k particles with an unscented tissue or cotton swab moistened with glass cleaner or distilled water. Do not rub the surface: lift the par ticles off with a soft repeated press.
5. Remove dust from fans and air vents with a soft bru s h, cotton swab, vacuum, or compressed air.
6. Reinstall the head covers.

Lubrication

Figure 20: Head cover
screws
The MAC III P erf ormance does not require lubrication under normal circumstances. The slides for the zoom and focus lens cars are lubricated with a long-lasting teflon-based grease that can be reapplied by a Martin service partner if necessary.

Replacing a color filter

Note: Wear cotton gloves while handling color filters and use only genuine Martin filters.
1. Power the lamp off but leave the fixture powered on with fans running and allow it to cool.
2. The top of the head is above the text on the lamp cover. Lock the head in a convenient position for
access to the top of the head.
3. Remove the two quarter-turn retaining screws (see Figure 20) from the top cover and lift it away from the
head. Let the cover hang on its safety wire or unclip the safety wire and remove the cover completely.
4. See A in Figure 21 on page 42. Rotate the color wheel until the filter you want to change is accessible.
Lift the filter away from the color wheel slightly to release it, then grasp it by the edges and remove. If your fingers are too large, protect the glass with a piece of paper that has been folded sev eral times and grasp the filter with needle nose pliers.
5. To insert a filter, slide it under the retention spri ng until it snaps into place.
6. If no further service work is to be carried out, reinstall the top cover with its safety wire and release the
tilt lock.
Service and maintenance 41
Page 42
A
B
Figure 21: Color filter and gobo replacement

Gobos in the MAC III Performance

The MAC III Performance uses specially-designed borosilicate 3.3 gobos with a heavy matted aluminum coating that require particularly careful handling and storage.
The use of metal gobos in the MAC III Performance is not recommended. Do not use gobos with dark coatings on any side, as these will absorb heat – either directly from the lamp or
reflected back from other gobos and optical components – and will not be durable.
Handling and storage
1. Store all gobos in a dust-free environment with approx. 50% humidity.
2. Always use clean gloves when handling gobos.
3. Avoid touching the other gobos when taking out a gobo from the rack: the sharp edge of one gobo can
scratch the others.
4. Clean the coated side of gobos with dust and oil-free compressed air only.
5. Clean the uncoated side of gobos with photographic quality lens-cleaner and optics cleaning tissues.
Use a repeated dabbing action rather than a rubbing action.
6. Avoid scratching coated and uncoated sides.
7. Never place a gobo with the coated side face-down on any surface.
8. Mount the gobo with the matted coating towards the lens.
42 MAC III Performance user manual
Page 43
Replacing rotating gobos
Important! The gobo can fall out if the spring is inserted backwards.
Do not lubricate gobo bearings: excess grease can cause loss of step.
Correct gobo orientation is critical. Read the guidelines in Figure 23 carefully before installing a gobo.
To replace a gobo:
1. Open the top cover as described under “Replacing a color filter”
on page 41.
2. See B in Figure 21 on page 42. Rotate the relevant gobo wheel
until the gobo you want to replace is accessible.
3. Grasp the holder by the teeth and pull the holder lightly away
from the gobo wheel to release the holder and remove it from the wheel.
4. With a small screwdriver or similar, unhook the end of the gob o spring furthest from the gobo and pull
out the spring. Drop the gobo out of the holder.
5. Insert the new gobo in the holder with the side that must face towards the lamp facing upwards, to wards
the spring (see Figure 22 and Figure 23).
6. Insert the spring with th e narrow end against the gobo, as shown in Figure 22. To identify the narrow
end, press the spring flat: the narrow end is on the inside. Push the end of the spring in under the lip of the holder.
7. Check that the gobo is seated flush against the holder. Press the spring as flat as possible against the
back of the gobo.
8. Check that the goboholder is the right way up (see Figure 21), then work the rim of the gobo holder
under both clips and snap the gobo holder back into position on the gobo wheel. If necessary, a small screwdriver or similar tool may be used to pry the clips away from the wheel.
9. If no further service work is to be carried out, reinstall the top cover with its safety wire and release the
tilt lock.
Figure 22: Rotating gobo holder
Service and maintenance 43
Page 44
Gobo orientation
abc
abc
The orientations shown in Figure 23 are correct in most cases, but consult your Martin dealer or gobo supplier if you are in any doubt about the orientation of a specific gobo type. To minimize the risk of heat damage, priority must be given to installing gobos with their more reflective sides facing the lamp.
Coated Glass Gobos
The heavy matted aluminum coated borosilicate gobos in the MAC III Performance are factory-installed with the more reflective sides facing towards the lamp. Replacement gobos must also be installed with more reflective sides facing the lamp.
More reflective side towards lamp
To minimize the risk of gobo overheating and damage, turn the more reflective side of a coated gobo towards the lamp.
Less reflective side away from lamp
The less reflective side of a coated gobo will absorb less heat if it faces away from the lamp.
Textured Glass Gobos
Textured side to wards lamp Smooth side away from lamp
Textured glass gobos in the MAC III Performan c e sit most squarely in the gobo wheel with the textured side towards the lamp. If in doubt, consult your Martin dealer or gobo supplier.
Image / text Gobos
True image towards lamp Reversed image away from lamp
Figure 23. Correct gobo orientation
44 MAC III Performance user manual
Page 45

Replacing the gobo animation wheel

Important! The gobo animation wheel is glass and m ust be h andled gentl y. Do not attempt to bend it or you will
break it. Breakages caused by mishandling are not covered by the pr od uct warranty.
1. Disconnect the fixture
from power and allow it to cool for 2 hours 45 minutes.
2. Apply the tilt lock in a
convenient position. Open the top cover as described under “Replacing a color filter” on page 41.
3. See Figure 24. Bring the
animation wheel up to the top of the head by pulling its sliding car with a finger.
4. The animation wheel is
retained by a magnetic hub. To avoid breaking the animation wheel while removing, release the hub by gently levering the hub off its mounting with a screwdriver. Do not apply pressure to the animation wheel itself. See Figure
25. Once the hub is released, you can safely grasp the wheel and remove it.
5. When installing an
animation wheel, slide the hub in over the drive mechanism and align it with its mounting until the magnetic hub locks into place on the mounting.
6. If no further service work
is to be carried out, reinstall the top cover with its safety wire and release the tilt lock before re-applying power.
Figure 24: Animation wheel access
Figure 25: Animation wheel removal
Service and maintenance 45
Page 46

Removing modules

The MAC III Performance is modular in design. A full procedure for removing and servicing effect modules is included in the Martin™ service package available for the MAC III Performance.
Important! The zoom/focus car and animation wheel
must be mo ved to the po sitions desc ribed below before modules can be removed.
1. See Figure 26. Move the zoom/focus car
as far as possible towards the front lens by first pushing on one of its sliders (A), then holding it in the fully forward position by pressing on one of its drive belt pulleys (B).
2. Move the gobo animation wheel as far as
possible up towards the top of the head by pulling on its drive car as shown in Figure 24 on page 45. The animation wheel is glass. Do not apply pressure to it, or you may cause damage that is not covered by the product warranty.
A
B
3. Modules are released for removal by
disconnecting their multi-connectors and removing their retaining screws (arrowed in Figure 27). Take great care not to damage wiring during module removal or re-installation.
Figure 26: Moving the zoom/focus car fully forward
Figure 27: Module retaining screws
46 MAC III Performance user manual
Page 47

MAC III Performance DMX protocol

Available in software 1.6.0 or later
Basic 16-bit Mode
16-bit Extended Mode
11
22
-3
DMX Value Percent Function
Strobe/shutter
0 - 19
20 - 49 50 - 64 65 - 69 70 - 84 85 - 89
90 - 104 105 - 109 110 - 124 125 - 129 130 - 144 145 - 149 150 - 164 165 - 169 170 - 184 185 - 189 190 - 204 205 - 209 210 - 224 225 - 229 230 - 244 245 - 255
0 - 255 0 - 100 0 - 255 0 - 100 Dimmer fade, fine (LSB)
0 - 255
0 - 7
8 - 19 20 - 25 26 - 27 28 - 33 34 - 35 36 - 41 42 - 43 44 - 49 50 - 51 52 - 57 58 - 59 60 - 65 66 - 67 68 - 73 74 - 75 76 - 81 82 - 83 84 - 89 90 - 91 92 - 97
98 - 100
0 - 100
Shutter closed (Lamp Switches to 800 watt mode after shutter is closed for 10 seconds)
Shutter open Strobe, fast slow Shutter open Opening pulse, fast slow Shutter open Closing pulse, fast slow Shutter open Random strobe, fast → slow Shutter open Random opening pulse, fast slow Shutter open Random closing pulse, fast slow Shutter open Burst pulse, fast slow Shutter open Random burst pulse, fast slow Shutter open Electronic sine wave strobe, fast slow Shutter open Electronic burst strobe, fast slow Shutter open
Dimmer fade (MSB)
Closed open
Cyan
White full cyan
34
128 - 254
45
128 - 254
0
1 - 127
255
0 - 255
0
1 - 127
255
Cyan range in random CMY color
when random CMY selected on channel 21 (16-bit) or 25 (16-bit extended)
0
1 - 50 51 - 99
100
0 - 100
0
1 - 50 51 - 99
100
Table 3: MAC III Performance DMX Protocol
Normal (full range) Minimum cyan setting (127 = full cyan) Maximum cyan setting (128 = no cyan) Normal (full range)
Magenta
White full magenta
Magenta range in random CMY color
when random CMY selected on channel 21 (16-bit) or 25 (16-bit extended)
Normal (full range) Minimum magenta setting (127 = full magenta) Maximum magenta setting (128 = no magenta) Normal (full range)
MAC III Performance DMX protocol 47
Page 48
Basic 16-bit Mode
16-bit Extended Mode
56
67
78
DMX Value Percent Function
Yellow
0 - 255
0
1 - 127
128 - 254
255
0 - 255 0 - 100
0
1 - 19
20
21 - 39
40
41 - 59
60
61 - 79
80
81 - 99
100
101 - 119
120
121 - 139
140
141 - 159
160
161 - 164 165 - 168 169 - 172 173 - 176 177 - 180 181 - 184 185 - 188 189 - 192
193 - 214 215 - 221 222 - 243
244 - 247 248 - 251 252 - 255
0 - 100
1 - 50 51 - 99
100
1 - 7
9 - 15
16
17 - 23
24
25 - 31
32
33 - 39
40
41 - 47
48
49 - 55
56
57 - 63
64
65 - 66 67 - 68 69 - 70 71 - 72 73 - 74 75 - 76 77 - 78 79 - 80
81 - 86 87 - 88 89 - 94
95 - 96 97 - 98
99 - 100
0
0
8
White full yellow
Yellow range in random CMY color
when random CMY selected on channel 21 (16-bit) or 25 (16-bit extended)
Normal (full range) Minimum yellow setting (127 = full yellow) Maximum yellow setting (128 = no yellow) Normal (full range)
CTO
Open (6000 K) warm (3200 K)
Color Wheel
Continuous Scroll
Open Open Slot 1 - Blue Slot 1 Slot 1 Slot 2 - Green Slot 2 Slot 2 Slot 3 - Orange Slot 3 Slot 3 Slot 4 - Minus green Slot 4 Slot 4 Slot 5 - Yellow Slot 5 Slot 5 Slot 6 - Congo (deep blue) Slot 6 Slot 6 Slot 7 - Red Slot 7 Slot 7 → Open Open
Stepped Scroll (snap to full color positions)
Slot 7 - Red Slot 6 - Congo (deep blue) Slot 5 - Yellow Slot 4 - Minus green Slot 3 - Orange Slot 2 - Green Slot 1 - Blue Open
Continuous Rotation
CW, Fast Slow Stop (This will stop wherever the wheel is at the time) CCW, Slow Fast
Random color
Fast Medium Slow
Table 3: MAC III Performance DMX Protocol
48 MAC III Performance user manual
Page 49
Basic 16-bit Mode
16-bit Extended Mode
89
910
10 11
DMX Value Percent Function
Gobo wheel: gobo selection, indexing, shake, rotation
Indexed gobo: set indexed angle on channel 9 (16-bit) or 10 (16-bit ext.)
0 - 9 10 - 14 15 - 19 20 - 24 25 - 29 30 - 34
35 - 39 40 - 44 45 - 49 50 - 54 55 - 59
60 - 89
90 - 119 120 - 149 150 - 179 180 - 209
210 - 232 233 - 255
0 - 255
0 - 2
3 - 126 127 - 129 130 - 253 254 - 255
0 - 255
0 - 255
0 - 4 4 - 5 5 - 8
8 - 10 10 - 12 12 - 14
14 - 16 16 - 18 18 - 20 20 - 22 22 - 24
24 - 34 35 - 45 46 - 56 57 - 67 68 - 78
79 - 89
90 - 100
0 - 100
0
1 - 50
51
52 - 99
100
0 - 100
0 - 100
Open Gobo 1 - Leaf breakup Gobo 2 - Dot breakup Gobo 3 - Limbo Gobo 4 - Linear 3 Gobo 5 - Raytraces
Continuous gobo rotation: set gobo rotation speed on channel 9 (16-bit) or 10 (16-bit ext.)
Gobo 1 - Leaf breakup Gobo 2 - Dot breakup Gobo 3 - Limbo Gobo 4 - Linear 3 Gobo 5 - Raytraces
Gobo shake centered on indexed position: set indexed angle on channel 9 (16-bit) or 10 (16-bit ext.). Shake angle increments in following steps: 10°, 15°, 30°, 45°, 60°, 90°, 135°, 180°, 270° and 360°
Gobo 1 - Leaf breakup, 360° slow 10° fast Gobo 2 - Dot breakup, 360° slow 10° fast Gobo 3 - Limbo, 360° slow 10° fast Gobo 4 - Linear 3, 360° slow 10° fast Gobo 5 - Raytraces, 360° slow 10° fast
Continuous gobo wheel scroll with continuous gobo rotation: set gobo rotation speed on channel 9 (16-bit) or 10 (16-bit extended)
CW scroll, fast slow CCW scroll, slow fast
Gobo wheel: indexing, direction, speed (MSB)
If indexed gobo is selected on channel 8 (16-bit) or 9 (16-bit ext.)
Rotating gobo indexing, 0 395°
If continuous gobo rotation is selected on channel 8 (16-bit) or 9 (16-bit ext.)
No rotation CW, fast slow No rotation CCW, slow fast No rotation
Gobo wheel: rotating gobo fine indexing or rotation speed (LSB)
If indexed gobo is selected on channel 8 (16-bit) or 9 (16-bit ext.)
Rotating gobo indexing, fine
If continuous gobo rotation is selected on channel 8 (16-bit) or 9 (16-bit ext.)
Rotating gobo rotation speed, fine
11 12
12 13
13 14
14 15
15 16
16 17
0 - 255 0 - 100
0 -126 127 - 128 129 - 255
0 - 255 0 - 100
0 -126 127 - 128 129 - 255
0 - 255 0 - 100
0 -126 127 - 128 129 - 255
0 - 49
50
51 - 100
0 - 49
50
51 - 100
0 - 49
50
51 - 100
Table 3: MAC III Performance DMX Protocol
Framing blade 1, position
Out in
Framing blade 1, angle
Angle – Parallel Angle +
Framing blade 2, position
Out in
Framing blade 2, angle
Angle – Parallel Angle +
Framing blade 3, position
Out in
Framing blade 3, angle
Angle – Parallel Angle +
MAC III Performance DMX protocol 49
Page 50
Basic 16-bit Mode
17 18
18 19
19 20
20 21
16-bit Extended Mode
22
23
24
DMX Value Percent Function
Framing blade 4, position
0 - 255 0 - 100
0 -126 127 - 128 129 - 255
0 - 199 200 - 225 226 - 229 230 - 255
0 - 255 0 - 100 Frame rotation: Fine indexing or rotation speed (LSB)
0 -19 20 - 39 40 - 59 60 - 79 80 - 84 85 - 89 90 - 94 95 - 99
100 - 104 105 - 109 110 - 114 115 - 119 120 - 124 125 - 129 130 - 134 135 - 139 140 - 144 145 - 149 150 - 255
0 - 255 0 - 100
0 - 2 3 - 5 6 - 8
9 - 11
165 - 167
168 169
216 217 218
228 229 230
252
253 - 255
0 - 49
50
51 - 100
0 - 78 79 - 88 89 - 90
91 - 100
0 - 7
7 - 16 17 - 24 25 - 31 31 - 33 33 - 34 34 - 35 36 - 37 38 - 39 40 - 41 42 - 43 44 - 45 46 - 47 48 - 49 50 - 51 52 - 53 54 - 55 56 - 57
58 - 100
0 1 2 3
65 66 66
85 85 85
89 90 90
99
100
Out in
Framing blade 4, angle
Angle – Parallel Angle +
Frame rotation: indexing or rotation (MSB)
0 - 395° CW, fast slow No rotation CCW, slow fast
Frame shape macros
No macro applied, individual framing blade control channels active Macro 1: Vertical Bar Macro 2: Horizontal Bar Macro 3: Square Macro 4: Parallelogram Right Macro 5: Parallelogram Left Macro 6: Trapezoid Up Macro 7: Trapezoid Left Macro 8: Trapezoid Down Macro 9: Trapezoid Right Macro 10: Equilateral Triangle Up Macro 11: Equilateral Triangle Left Macro 12: Equilateral Triangle Down Macro 13: Equilateral Triangle Right Macro 14: Right-angled Triangle Down Left Macro 15: Right-angled Triangle Down Right Macro 16: Right-angled Triangle Up Right Macro 17: Right-angled Triangle Up Left Reserved for future use
Frame shape macro size
Small large
Frame shape macro crossfade timing
Follow console timing
0.2 seconds
0.4 seconds
0.4 seconds
0.2-second intervals up to 10.8 seconds
11 seconds 12 seconds 13 seconds
1-second intervals up to 60 seconds
60 seconds 65 seconds 70 seconds
5-second intervals up to 120 seconds
120 seconds 130 seconds 140 seconds
10-second intervals up to 360 seconds
360 seconds Follow console timing
Table 3: MAC III Performance DMX Protocol
50 MAC III Performance user manual
Page 51
Basic 16-bit Mode
16-bit Extended Mode
21 25
22 26
23 27
24 28
25 29
26 30
27 31
-32
DMX Value Percent Function
Color/CMY macros
0 - 18
19 - 57
58 - 83
84 - 109 110 - 135 136 - 207 208 - 255
0 - 5
6 - 10 11 - 15 16 - 20
21 - 25
26 - 110 111 - 195 196 - 255
0 - 255
0 - 2
3 - 126 127 - 129 130 - 253 254 - 255
0 -19 20 - 39 40 - 59
60 - 79
80 - 255
0 - 255
0 - 2
3 - 126
127 - 129 130 - 253 254 - 255
0 - 199
200 - 215 216 - 229 230 - 243 244 - 249 250 - 255
0 - 255 0 - 100 0 - 255 0 - 100 Focus, fine (LSB)
0 - 6
7 - 22
23 - 32 33 - 42 43 - 52 53 - 82
83 - 100
0 - 2 2 - 4 4 - 6 6 - 8
8 - 10 10 - 43 44 - 76
77 - 100
0 - 100
0
1 - 50
51
52 - 99
100
0 - 7
7 - 16 17 - 24
25 - 31
32 - 100
0 - 100
0
1 - 50
51
52 - 99
100
0 - 77 78 - 84 85 - 89 90 - 94 95 - 97
98 - 100
No function (Note: this value is used for setting calibration values on channel 34/40)
Color wheel: fast narrow shake slow wide shake, around currently selected color
Random CMY: set min./ max. CMY range limits on channels 3 - 5 (16-bit) or 4
- 6 (16-bit ext.)
Fast Medium Slow Crossfading speed on rotating gobo wheel slow fast
No function
Gobo animation wheel: position and function
Open Horizontal indexed position: set indexing on ch. 23 (16-bit) or 27 (16-bit ext.) Vertical indexed position: set indexing on ch. 23 (16-bit) or 27 (16-bit ext.) Horizontal position, continuous rotation: set direction & speed on ch. 23
(16-bit) or 27 (16-bit ext.) Vertical position, continuous rotation: set direction & speed on ch. 23 (16-bit)
or 27 (16-bit ext.) Angled position, vertical horizontal, continuous rotation: set direction &
speed on ch. 23 (16-bit) or 27 (16-bit ext.) Angled position, horizontal vertical: set indexing on ch. 23 (16-bit) or 27
(16-bit ext.) Angled position, vertical open: set indexing on ch. 23 (16-bit) or 27 (16-bit
ext.)
Gobo animation wheel: indexed angled position, rotation direction and speed
If indexed angled position is selected on channel 22 (16-bit) or 26 (16-bit ext.):
Indexed angle, 0° 395°
If continuous rotation is selected on channel 22 (16-bit) or 26 (16-bit ext.):
No rotation CW, fast slow No rotation CCW, slow fast No rotation
Beam effect (frost or prism depending on which is installed)
Beam effect off Beam effect 1 indexing: set angle on ch. 25 (16-bit) or 29 (16-bit ext.) Beam effect 1 rotating: set direction and speed on ch. 25 (16-bit) or 29 (16-bit
ext.) Beam effect off
No function
Beam effect (frost or prism depending on which is installed) indexing angle, rotation direction and speed
If beam effect indexing is selected on channel 24 (16-bit) or 28 (16-bit ext.):
Indexed angle 0° - 395°
If beam effect rotation is selected on channel 24 (16-bit) or 28 (16-bit ext.):
No rotation CW, fast slow No rotation CCW, slow fast No rotation
Iris
Open closed Closed Opening pulse, fast slow Closing pulse, fast slow Random opening pulse, fast slow Random closing pulse, fast slow
Focus (MSB)
Infinity near
Table 3: MAC III Performance DMX Protocol
MAC III Performance DMX protocol 51
Page 52
Basic 16-bit Mode
16-bit Extended Mode
28 33
-34 29 35 30 36 31 37 32 38
DMX Value Percent Function
0 - 255 0 - 100 0 - 255 0 - 100 Zoom, fine (LSB)
0 - 255 0 - 100 0 - 255 0 - 100 Pan, fine (LSB)
0 - 255 0 - 100 0 - 255 0 - 100 Tilt, fine (LSB)
Table 3: MAC III Performance DMX Protocol
Zoom (MSB)
Flood spot
Pan (MSB) Left right (128 = neutral)
Tilt (MSB)
Left right (128 = neutral)
52 MAC III Performance user manual
Page 53
Basic 16-bit Mode
33 39
16-bit Extended Mode
DMX Value Percent Function
Fixture control/settings
0 - 9 10 - 14 15 - 19 20 - 24 25 - 29 30 - 34 35 - 39 40 - 44 45 - 49 50 - 54 55 - 59
60 - 64 65 - 69 70 - 74 75 - 79 80 - 84
85 - 89
0 - 1 2 - 3 4 - 5 6 - 7
8 - 9 10 - 11 12 - 13 14 - 15 16 - 17 18 - 19 20 - 21
22 - 23 24 - 25 26 - 27 28 - 29 30 - 31
32 - 33
No function
Reset entire fixture Reset dimmer and shutter only Reset CMYC and color wheel only Reset effects module (gobo wheel, framing, gobo animation, iris, frost) only Reset zoom and focus only Reset pan and tilt only
No function
Lamp on Lamp off No function (Note: this value is used for managing pan/tilt limits and storing
calibration values on channel 34/40) Dimmer curve = Optically linear
(menu override, setting unaffected by power off/on)(2) Dimmer curve = Square law
(menu override, factory default setting, setting unaffected by power off/on)(2) Dimmer curve = Inverse square law
(menu override, setting unaffected by power off/on)(2) Dimmer curve = S-curve
(menu override, setting unaffected by power off/on)(2)
No function
Pan & tilt speed = Normal (menu override - Setting returns to MENU setting after power on/off)
90 - 94
34 - 35
Pan & tilt speed = F ast (menu o verride - Setting returns to MENU setting after power on/off)
95 - 99
36 - 37
Pan & tilt speed = Slow (menu ov erride - Setting returns to MENU setting after
power on/off) 100 - 139 140 - 144
145 - 149 100 - 154
155 - 159 160 - 164 165 - 169 170 - 174 175 - 199 200 - 204 205 - 209 210 - 214 215 - 219 220 - 224 225 - 239 240 - 244 245 - 249 250 - 255
38 - 53 54 - 55
56 - 57 58 - 59
60 - 61 62 - 63 64 - 65 66 - 67 68 - 77 78 - 79 80 - 81 82 - 83 84 - 85 86 - 87 88 - 93 94 - 95 96 - 97
98 - 100
No function
Parameter shortcuts = ON
(menu override, setting stays at factory default ON at power off/on)
Parameter shortcuts = OFF
(menu override, setting returns to factory default ON at power off/on)
No function
Disable zoom/focus linking
Enable zoom/focus linking, near distance
Enable zoom/focus linking, medium distance (factory default setting)
Enable zoom/focus linking, far distance
No function
Ballast output full, set to 1500 W
Ballast output reduced, output set to 1200 W
Ballast output reduced, output set to 1100 W
Ballast output reduced, output set to 1000 W
Ballast output reduced, output set to 900 W
No function
Illuminate display on fixture
No function
Trigger event log (inserts new dynamic content into current report)
(1)
If DMX Reset or DMX Lamp Off are disabled in the control menus, a full or
partial reset command or a lamp off command can be executed only if:
Slot 1 is selected on the color wheel (DMX value 20 on channel 7 in16-bit or 8 in 16-bit ext.), and
The beam effect (frost filter or prism) is on (DMX value 20-59 on channel 24 in 16-bit or 28 in 16-bit ext.), and
Open gobo is selected on the gobo wheel (DMX value 0 on channel 8 in 16-bit or 9 in 16-bit ext.)
(2)
Value must be held for 5 seconds to activate
(1)
(1)
(1)
(1)
(1)
(1)
(1, 2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
(2)
Table 3: MAC III Performance DMX Protocol
MAC III Performance DMX protocol 53
Page 54
Basic 16-bit Mode
34 40
16-bit Extended Mode
DMX Value Percent Function
Fixture adjustments/calibration
0 - 39 40 - 44 45 - 49 50 - 54 55 - 59 60 - 64 65 - 69 70 - 74 75 - 79 80 - 84 85 - 89 90 - 94 95 - 99
100 - 104 105 - 109 110 - 114 115 - 124 125 - 129 130 - 134 135 - 139 140 - 144 145 - 149 150 - 154 155 - 159 160 - 179 180 - 184 185 - 189 190 - 194 195 - 199 200 - 204 205 - 209 210 - 214 215 - 219 220 - 224 225 - 229 230 - 234 235 - 239 240 - 244 245 - 249 250 - 255
0 - 13 14 - 15 16 - 17 18 - 19 20 - 21 22 - 23 24 - 25 26 - 27 28 - 29 30 - 31 32 - 33 34 - 35 36 - 37 38 - 39 40 - 41 42 - 43 44 - 47 48 - 49 50 - 51 52 - 53 54 - 55 56 - 57 58 - 59 60 - 61 62 - 69 70 - 71 72 - 73 74 - 75 76 - 77 78 - 79 80 - 81 82 - 83 84 - 85 86 - 87 88 - 89 90 - 91 92 - 93 94 - 95 96 - 97
98 - 100
No function:
Enable pan/tilt limitation
No function
Disable pan/tilt limitation
No function
Set pan/tilt limit: head must stay inside defined area (create safe zone)
No function
Set pan/tilt limit: head must stay outside defined limits (create no-go zone)
No function
Store current pan position as lower pan limit Store current pan position as upper pan limit
No function
Store current tilt position as lower tilt limit Store current tilt position as upper tilt limit
No function
Reset pan and tilt limits
No function
Store dimmer calibration Store cyan calibration Store magenta calibration Store yellow calibration Store CTC calibration Store CMYC calibration Store gobo wheel slots 1 – 5 index calibration
No function
Store framing blade 1 calibration Store framing blade 2 calibration Store framing blade 3 calibration Store framing blade 4 calibration Store framing blade rotation calibration Store gobo animation wheel index calibration Store beam effect (prism) index calibration Store iris calibration Store focus calibration Store zoom calibration Store pan calibration Store tilt calibration
No function
Reset all calibrations to factory default
No function
(3)
To activate:
Value must be held for 5 seconds The CMY channels (3, 4 and 5 in 16-bit mode or 4, 5 and 6 in 16-bit
extended mode) must all be set to DMX value 232 The beam effect channel (24 in 16-bit mode or 28 in 16-bit extended
mode) must be set to DMX value 030.
(4)
To activate:
Value must be held for 5 seconds Color/CMY macros channel 21 in 16-bit or 25 in 16-bit ext. must be set
to DMX value 005 - 010 Fixture control channel 33 in 16-bit or 39 in 16-bit ext. must be set to
DMX value 055 - 059.
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(3)
(4)
(4)
(4)
(4)
(4)
(4)
(4)
(4) (4) (4) (4)
(4)
(4)
(4)
(4)
(4) (4)
(4)
(4)
(4)
Table 3: MAC III Performance DMX Protocol
MSB = Most significant byte LSB = Least significant byte
54 MAC III Performance user manual
Page 55

Control panel menus

Commands marked * can also be executed via DMX
Menu level 1 Menu level 2 Menu level 3 Menu level 4 Notes (Default settings in bold print)
Gives quick access to most frequently-used menus: FACTORY SETTINGS, DMX ADDRESS, PROTOCOL
SETUP WIZARD
DMX ADDRESS
PROTOCOL SET
FIXTURE ID 0000 – 9999 User-settable fixture ID number
PERSONALITY
SET, FIXTURE ID plus most frequently-used PERSONALITY settings: PAN/TILT SETTINGS, SPEED SETTINGS, FANS, DIMMING CURVE, AUTOMATIC LAMP ON, DISPLAY. See table below for details of
these settings.
1 – 479 (16-bit) 1 – 473 (16-bit ext.)
16 Bit
16 Bit extended
PAN/TILT SETTINGS
SPEED SETTINGS
SWAP PAN INVERT Reverse DMX pan control: right left
TILT INVERT Reverse DMX tilt control: down up MOVE ON RESET
P/T LIMITATION Enable pan and tilt range limits PAN MINIMUM Set minimum pan angle ( – 360°) PAN M AXIMUM Set maximum pan angle (360° – 0°)
PAN & TILT LIMIT SETTINGS
PAN & TILT SPEED
EFFECT SPEED
TILT MINIMUM Set minimum tilt angle (-134° – 134°) TILT MAXIMUM Set maximum tilt angle (134° – -134°)
P/T LIMIT AREA DEFAULT LIMIT
SETTINGS? Normal Normal speed pan and tilt Fast Optimize pan/tilt movement for speed
Slow
Follow P/T speed
Normal Normal effects speed Fast Optimize effects movement for speed
Slow
DMX address (new fixtures are supplied with address set to 1)
16-bit basic DMX mode with 2-channel (coarse and fine) control of rotating gobo indexing or speed, pan, and tilt
16-bit extended DMX mode with basic mode features plus fine control of dimmer, focus and zoom
Map DMX pan control to tilt channel and vice versa
Enable/disable pan/tilt movement when fixture resets. Default = On
Set pan/tilt to stay inside safe zone or sta y outside no-go zone (Inside/Outside)
Reset all pan and tilt limit settings to factory defaults.
Optimize pan/tilt movement for smoothness
Effects speed follows the speed setting applied to pan and tilt via DMX or in control menu
Optimize effects movement for smoothness
Table 4: Control menus
Control panel menus 55
Page 56
Menu level 1 Menu level 2 Menu level 3 Menu level 4 Notes (Default settings in bold print)
Sets lamp cooling fans to 50% capacity (color temperature of light output from the lamp is different at different thermal lamp temperatures)
Fan cleaning mode activated automatically if fan error reported
Cooling fans stop when lamp is powered off
S-curve (fixture emulates incandescent lamp voltage linear RMS dimming curve)
Enables zoom focus linking, optimized for short-throw projection (5 - 10 m)
Enables zoom focus linking, optimized for medium-throw projection (10 - 20 m)
Enables zoom focus linking, optimized for long-throw projection (20+ m)
Enables/disables followspot mode. In followspot mode DMX control of pan and tilt is disabled and the pan and tilt motors are disengaged so the head can be freely moved using a followspot handle.
Engages or disengages both the pan and tilt motors acting as a brake on head movement. DMX control over pan is still disabled and this is only available when followspot mode is on.
Will engage (ON) the pan motor to acts as a brake on head movement, or disengage (OFF) it so the head can be freely panned using a followspot handle. DMX control over pan is still disabled and this command is only available when followspot mode is on.
Will engage (ON) the tilt motor to acts as a brake on head movement, or disengage (OFF) it so the head can be freely tilted using a followspot handle. DMX control over tilt is still disabled and this command is only available when followspot mode is on.
Lamp strikes automatically within 90 seconds of fixture being powered on
Lamp strikes automatically when the fixture receives a DMX signal
Lamp cannot be powered off via DMX (can be overridden: see DMX protocol)
Fixture cannot be reset via DMX (can be overridden: see DMX protocol)
PERSONALITY
(continued)
FANS
DIMMING CURVE
FOCUS TRACKING
FOLLOWSPOT MODE
AUTOMATIC LAMP ON
DMX LAMP OFF
DMX RESET
LAMP COOLING
FAN CLEAN
FAN MODE
Optical linear Optically linear dimming curve S-Curve Square law Square law dimming curve
Inv.sq.law Inverse square law dimming curve Off Disables zoom focus linking
Near
Medium
Far
FOLLOWSPOT MODE
LOCK/UNLOCK PAN & TILT
LOCK PAN Off / On
LOCK TILT Off / On
Off Automatic lamp striking disabled On
DMX
Off On Lamp can be powered off via DMX Off On Fixture can be reset via DMX
50%
80% Sets lamp cooling fans to 80% capacity Off Sets all cooling fans to no cleaning
Auto Forced Sets all cooling fans to run at 100%
Always on Cooling fans operate constantly
Follow lamp off
Off / On
Table 4: Control menus
56 MAC III Performance user manual
Page 57
Menu level 1 Menu level 2 Menu level 3 Menu level 4 Notes (Default settings in bold print)
Effects avoid open positions during effects changes
Effects take shortest route during changes, crossing open positions if necessary.
Display goes into sleep mode 2 minutes after last key press
Display goes into sleep mode 5 minutes after last key press
Display goes into sleep mode 10 minutes after last key press
Rotate display manually or set to auto-rotate to match fixture orientation
Enable error messages and warnings in display
Disable error messages and warnings in display (the LED in the jog wheel will still light to indicate fixture status if an error has been detected or the fixture has a warning)
Return all settings (except calibrations) to factory defaults
Display hours fixture has been powered on since manufacture (not user-resettable)
Display hours fixture has been powered on since last counter reset (user-resettable)
Reset RESETTABLE POWER ON counter to zero.
Display hours of lamp use since manufacture (not user-resettable)
Display hours of lamp use since last counter reset (user-resettable)
Reset RESETTABLE LAMP ON counter to zero.
Display number of times lamp has been struck since manufacture (not user-resettable)
Display number of times lamp has been struck since last counter reset (user-resettable)
Reset RESETTABLE LAMP STRIKES counter to zero.
Display hours fixture has been powered on since timer was last cleared.
AIR FILTER timer to zero.
PERSONALITY
(continued)
FACTORY SETTINGS
FIXTURE INFORMATION
Off
PARAMETER SHORTCUTS
DISPLAY
DISPLAY INTENSITY
DISPLAY ROTATION
ERROR MODE
LOAD FACTORY SETTINGS FIRMWARE
VERSION
POWER ON TIME
LAMP ON TIME
LAMP STRIKES
AIR FILTERS
MAC ID xx.xx.xx.xx.xx.xx Fixture’s MAC address SERIAL NUMBER (xx)xxxxxxxxxxxx Fixture’s serial number RDM UID xxxx.xxxxxxxx Fixture’s unique RDM ID
On
On Display permanently on 2 min.
5 min.
10 min. Auto Display auto-adjusts to ambient light level
1 - 100% Manually set display intensity 0° / 90° / 180° / 270° / Auto
Normal
Silent with LED
Vxx.xx.xx Fixture software version
TOTAL POWER ON
RESETTABLE POWER ON
CLEAR RESETTABLE POWER ON
TOTAL LAMP ON
RESETTABLE LAMP ON
CLEAR RESETTABLE LAMP ON
TOTAL LAMP STRIKES
RESETTABLE LAMP STRIKES
CLEAR RESETTABLE LAMP STRIKES
RESETTABLE AIR FILTER SET TIME ALERT Set alert timer from 0 - 750 hours.
CLEAR RESETTABLE AIR FILTER Resets
Table 4: Control menus
Control panel menus 57
Page 58
Menu level 1 Menu level 2 Menu level 3 Menu level 4 Notes (Default settings in bold print)
FAN SPEED Displays speed in RPM of all cooling fans
Displays temperature in °C of all PCBs and of ballast capacitor
Displays voltage at mains power input, voltage, current and wattage at lamp terminals, lamp status, igniter status and lamp intensity.
DMX transmission speed in packets per second
DMX value (0 - 255) received on each channel
Values for fine control channels can only be viewed if available in the DMX mode the fixture is set to
Enable pan/tilt position feedback systems
For use by qualified service technicians – see Martin service documentation before entering this menu
Move pan and tilt to end stops following instructions in the display, then execute to calibrate pan and tilt sensors
Set individual effects to calibration positions (approx. +/- 5% offset available)
Replace factory default calibration settings with current calibration settings
Execute to update fixture firmware from bank shown in display
Clears event log and any current errors
FIXTURE INFORMATION
(continued)
DMX LIVE
TEST SEQUENCE
MANUAL CONTROL
SERVICE
TEMPERATURE
POWER UNIT
EVENT LOG VIEWER Views fixture event log RATE QUALITY Percent of packets received
START CODE Value of the DMX start code
STROBE/SHUTTER FIXTURE ADJUSTM E NTS
ACTION Start / Stop / Pause Run test sequence of all functions REPEAT On / Off Enable auto-repeat of test sequence STATUS DURATION Scene status information for test sequence RESET ACTION Click jog wheel to reset fixture LAMP ON/OFF ACTION Manually strike/douse lamp STROBE/SHUTTER TILT Set each effect manually.
PAN/TILT FEEDBACK
ADJUST
CALIBRATION
UPDATE FIRMWARE
EVENT LOG
On Off Disable pan/tilt position feedback
CMY MODULE DIMMER EFFECT MODULE SHUTTER
PAN/TILT MODULE
PAN/TILT SENSOR CALIBRATION
DIMMER ... TILT LOAD DEFAULTS? Load factory default calibration settings SAVE FACTORY DEFAULT?
UPDATE BANK Firmware bank version
LOCATION Location of firmware bank EVENT LOG TRIGGER Triggers generation of event log CLEAN EVENT LOG
PAN TILT
PAN/TILT AT END STOP
Table 4: Control menus
58 MAC III Performance user manual
Page 59

Service and display messages

The MAC III Perf ormance gives service and maintenance information by displaying a large 3- or 4-character short code and a smaller full-text message in the display. The short code is visible at a distance, allowing error identification with the fixture still in the rig, for example, while the full-text message gives more detailed information about the error.

Service warnings

If the MAC III Performance requires service, it displays a warning indicating the service required. The most important short codes and messages are given in T a ble 5 below
Short code Full-text message
LLW LAMP LIFE WARNING
Lamp life is within 10% of its limit.
AIRS AIR FILTER SERVICE WARNING (s/w versions from ver. 1.3)
The timer available in the SERVICE menu has reached the point for which the alarm was set.
AFSW AIR FILTER SERVICE WARNING (s/w versions prior to ver. 1.3)
The timer available in the SERVICE menu has reached the point for which the alarm was set.
Table 5: Service warning messages

Error messages

:
The MAC III Performance monitors its own operation. If it detects an error, it displays an error warning. The most important short codes and messages are given in Table 6 below:
Short code Full-text message
APER ANIMATION WHEEL POSITION ERROR ARER ANIMATION WHEEL ROTATION ERROR BANK UNABLE TO UNPACK BANK
BATM BATTERY MODE
BEER BEAM SHAPER ERROR
BOTV BOOTLOADER(S) VERSION NOT VALID
BRER BEAM SHAPER ROTATION ERROR
BT W BASE TEMPERATURE TOO HIGH
BTCO BASE TEMPERATURE CUTOFF
BTER BASE TEMP HIGH
C1ER COLOR WHEEL 1 ERROR CCDE CMY CALIBRATE DATA PCB (s/w versions prior to ver. 1.3)
CDCM CALIBRATE DATA CMY
CDEF CALIBRATE DATA EFFECT
Error unpacking firmware during/after software reload
Switched to battery power source with limited functionality. Plug in power cable to restore full function operation.
Decentralized firmware in module cannot be replaced / does not match bank. Module or module bootloader replacement required.
At least one base PCB temperature >75°C
At least one base PCB temperature >85°C
The temperature on a PCB in the base is high. A fan might be defective or the ambient temperature may be too high.
Unable to read/write data to external EEPROM board (calibrate date) on CMY module
Unable to read/write data to external EEPROM board (Calibrate Data) on CMY module. The PCB needs to be replaced.
Unable to read/write data to external EEPROM board (Calibrate Data) on Effect module. The PCB needs to be replaced.
T able 6: Error messages
Service and display messages 59
Page 60
Short code Full-text message
CDPT CALIBRATE DATA PAN/TILT
CDZF CALIBRATE DATA ZOOM/FOCUS
CECH COM ERROR CHARGER
CECM COM ERROR CMY
CECO COM ERROR COOLING
CEEF COM ERROR EFFECT
CELF CLEAN EVENT LOG FAILED
CEPT COM ERROR PAN/TILT
CEPU COM ERROR POWER UNIT
CEUI COM ERROR UI
CEZF COM ERROR ZOOM/FOCUS
COLD FIXTURE IS COLD
CONC COOLING NO CONNECTION
CONE EFFECT NO CONNECTION
CONM CMY NO CONNECTION
CONP PAN/TILT NO CONNECTION
CONZ ZOOM/FOCUS NO CONNECTION
CTER CTC ERROR
CYER CYAN ERROR
DIER DIMMER ERROR
DINA DIMMER NOT ADJUSTED
ECDE EFFECT CALIBRATE DATA PCB
EEDF WRITING EEPROM DEFAULT(S)
EEPR EEPROM INVALID/NO CONN.
EFSM ERROR FAILSAFE MODE
FAN LAMP R FAN ERROR
Unable to read/write data to external eeprom board (Calibrate Data) on Yoke. The PCB needs to be replaced.
Unable to read/write data to external eeprom board (Calibrate Data) on Zoom/Focus module. The cables need to be checked or the module may need to be replaced.
I2C communication between main controller and charger failed. The cables need to be checked or the module may need to be replaced.
CAN communication between main controller and CMY driver failed. The cables need to be checked or the driver may need to be replaced.
CAN communication between main controller and cooling driver failed. The cables need to be checked or the driver may need to be replaced.
CAN communication between main controller and effects driver failed. The cables need to be checked or the driver may need to be replaced.
CAN communication between main controller and pan/tilt driver failed. The cables need to be checked or the driver may need to be replaced.
I2C communication between main controller and ballast failed. The cables need to be checked or the module may need to be replaced.
User interface communication failure. The cab les need to be check ed or the module ma y need to be replaced.
CAN communication between main controller and zoom/focus driver failed. The cables need to be checked or the driver may need to be replaced.
PCBs are below -20° C (-4° F)
(s/w versions prior to ver. 1.3)
(s/w versions prior to ver. 1.3)
(s/w versions prior to ver. 1.3)
(s/w versions prior to ver. 1.3)
(s/w versions prior to ver. 1.3)
The sensors, wiring and motor need to be checked and the driver PCB may need to be replaced.
The sensors, wiring and motor need to be checked and the driver PCB may need to be replaced.
The sensors, wiring and motor need to be checked and the driver PCB may need to be replaced.
Dimmers need to be adjusted by a qualified service technician.
(s/w versions prior to ver. 1.3) Unable to read/write data to external EEPROM board (calibrate date) on effect module
No valid EEPROM in a CAN module. Writing default into the EEPROM based on the CAN address. Module is possibly incorrectly connected
No connection or EEPROM data invalid
Module error detected during self-check at startup. Service intervention required. Fixture control possibly disabled, depending on nature of error.
T able 6: Error messages
60 MAC III Performance user manual
Page 61
Short code Full-text message
FAN LAMP L FAN ERROR FAN BOTTOM FAN ERROR FAN CMY FAN ERROR FAN TOP FAN ERROR FAN MAINBOARD FAN 1ERROR FAN POWER FAN 1 ERROR FAN POWER FAN 2 ERROR
FBEP PAN FEEDBACK ERROR
Unable to correct pan position
FBET TILT FEEDBACK ERROR
Unable to correct tilt position
FOER FOCUS ERROR
FRER FRAMING ROTATION ERROR
FSER FRAMING SHUTTER 1 INS ERROR
FSER FRAMING SHUTTER 1 ANG ERROR
FSER FRAMING SHUTTER 2 INS ERROR
FSER FRAMING SHUTTER 2 ANG ERROR
FSER FRAMING SHUTTER 3 INS ERROR
FSER FRAMING SHUTTER 3 ANG ERROR
FSER FRAMING SHUTTER 4 INS ERROR
FSER FRAMING SHUTTER 4 ANG ERROR
FUSB FORCED USB UPLOAD ENABLED
G11M GOBO WHEEL GOBO 1 MISSING
G12M GOBO WHEEL GOBO 2 MISSING
G13M GOBO WHEEL GOBO 3 MISSING
G14M GOBO WHEEL GOBO 4 MISSING
G15M GOBO WHEEL GOBO 5 MISSING
G1ER GOBO WHEEL ERROR
GELF GENERATE EVENT LOG FAILED GOER GOBO WHEEL ERROR
HOT LAMP TOO HOT TO RESTRIKE
HT W HEAD TEMPERATURE TOO HIGH
HTCO HEAD TEMP CUT OFF
HTER HEAD TEMP HIGH
IRER IRIS ERROR
LAER LAMP ERROR
The fixture has been started in forced upload mode (the Escape button was held during power up).
The gobo is not installed, faulty, or operating in extremely cold temperatures. Instal, replace or allow the gobo to warm up.
The gobo is not installed, faulty, or operating in extremely cold temperatures. Instal, replace or allow the gobo to warm up.
The gobo is not installed, faulty, or operating in extremely cold temperatures. Instal, replace or allow the gobo to warm up.
The gobo is not installed, faulty, or operating in extremely cold temperatures. Instal, replace or allow the gobo to warm up.
The gobo is not installed, faulty, or operating in extremely cold temperatures. Instal, replace or allow the gobo to warm up.
The sensors, wiring and motor need to be checked and the driver PCB may need to be replaced.
The fixture will attempt to restrike at 20 second intervals. After 90 seconds if the lamp still refuses to strike, LERR is displayed
One or more of the PCB's in the head is above 85 degrees celsius. Power off the fixture, allow it to cool, and restart.
One or more of the PCB's in the head is above 95 degrees celsius. Power off the fixture, allow it to cool, and restart.
The temperature on a PCB in the head is high. A fan might be defectiv e or the ambient temperature may be too high.
The lamp is defective or has exploded, is missing, or the lamp cannot restrike after 90 seconds.
T able 6: Error messages
Service and display messages 61
Page 62
Short code Full-text message
LSER LAMP SENSING CIRCUIT ERROR (s/w versions from ver. 1.3)
LSRR LAMP SENSING CIRCUIT ERROR (s/w versions prior to ver. 1.3)
LTIM LAMP LIFE WARNING
MAER MAGENTA ERROR MALE MAINS LOW
MALW MAINS LOW
PAER PAN ERROR
PANA PAN NOT ADJUSTED
PCDE PAN/TILT CALIBRATE DATA PCB (s/w versions prior to ver. 1.3)
PSER PAN SENSOR ERROR PTCM PAN/TILT SENSOR CAL MISSING
PTCO PSU TEMP CUTOFF
PTCS PAN/TILT CALIBRATE SENSOR (s/w versions prior to ver. 1.3)
PTER PSU TEMP HIGH
R1ER GOBO WHEEL ROTATION ERROR SHNA SHUTTER NOT ADJUSTED
SHUE SHUTTER ERROR
SLER SAFETY LOOP ERROR
SSTO SYSTEM STATE TIMEOUT
TIER TILT ERROR TINA TILT NOT ADJUSTED
TSER TILT SENSOR ERROR UECH UPLOAD ERROR CHARGER
UECM UPLOAD ERROR CMY
UECO UPLOAD ERROR COOLING
UEEF UPLOAD ERROR EFFECT
UEPT UPLOAD ERROR PAN/TILT
UEPU UPLOAD ERROR POWER UNIT
UEUI UPLOAD ERROR UI
UEZF UPLOAD ERROR ZOOM/FOCUS
UPLB UPLOAD ERROR ON BALLAST (s/w versions prior to ver. 1.3)
UPLC UPLOAD ERROR ON COOLING (s/w versions prior to ver. 1.3)
Lamp sensing circuit reports that lamp should be on but is not actually on.
Lamp sensing circuit reports that lamp should be on but is not actually on.
Lamp on counter has timed out and it is time to change the lamp. The counter must be reset once this is done.
The input voltage on the electronic ballast is too low to strike the lamp.
Mains voltage is below acceptable level. The lamp may not be able to strike.
Pan needs to be adjusted by a qualified service technician.
Unable to read/write data to external EEPROM board (calibrate date) on yoke
The pan/tilt sensors are not calibrated.
Ballast in thermal cutoff
Pan/tilt sensors not calibrated
The temperature on a PCB in the power supply unit or ballast is high. A fan might be def ectiv e or the ambient temperature may be too high.
No shutter adjustment data in EEPROM
Lamp safety loop circuit activated: the lamp access hatch is open or lamp is too hot
Failure to communicate with module during self-check at startup. Service intervention required. Fixture control possibly disabled, depending on nature of error.
Tilt needs to be adjusted by a qualified service technician.
Could not upload new firmware to the Charger module.
Could not upload new firmware to the CMY module.
Could not upload new firmware to the Cooling module.
Could not upload new firmware to the Effects module.
Could not upload new firmware to the Pan/Tilt Focus module.
Could not upload new firmware to the Power Unit module.
Could not upload new firmware to the User Interface module.
Could not upload new firmware to the Zoom Focus module.
T able 6: Error messages
62 MAC III Performance user manual
Page 63
Short code Full-text message
UPLD DMX UPLOAD ERROR
UPLD DMX UPLOAD ERROR
UPLE UPLOAD ERROR ON EFFECT (s/w versions prior to ver. 1.3)
An error occurred during upload via DMX. Check cabling and connections, and then restart.
Firmware upload via DMX failed.
T able 6: Error messages
Service and display messages 63
Page 64

Troubleshooting

Problem Probable cause(s) Remedy
No power to fixture.
One or more of the fixtures is completely dead.
Fixtures reset correctly but respond erratically or not at all to the controller.
Time out error after fixture reset. Effect requires mechanical adjustment. Contact Martin technician for service. Mechanical effect loses
position.
No light and lamp error message displayed.
Lamp cuts out intermittently. Fixture is too hot.
Primary fuse blown (located near mains inlet). Isolate fixture from power and replace fuse. Secondary fuse(s) blown (located on PCBs in
base). Bad data link.
Data link not terminated. Incorrect addressing of fixtures. Check fixture address and protocol settings.
One of the fixtures is defective and disturbs data transmission on the link.
DMX and RDM ports switched
Mechanical train requires cleaning, adjustment, or lubrication.
Lamp blown Disconnect fixture and replace lamp. Lamp not installed Disconnect fixture and install lamp.
Lamp access door safety switch open
Check that power is switched on and cables are plugged in.
Isolate fixture from power. Check fuses and replace.
Inspect connections and cables. Correct poor connections. Repair or replace damaged cables.
Insert DMX termination plug in data output socket of the last MAC III Performance on the data link.
Unplug the XLR in and out connectors and connect them directly together to bypass one fixture at a time until normal operation is regained. Have the fixture serviced by a qualified technician.
Check that data port settings match desired pinout at XLR connectors
Contact Martin technician for service.
Verify that lamp access door is fully seated and locked in place.
Allow fixture to cool. Clean fixture. Reduce ambient temperature.
Table 7: Troubleshooting
64 MAC III Performance user manual
Page 65

Specifications

Physical
Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690 mm (27.2 in.)
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 536 mm (21.1 in.)
Height (head straight up) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 914 mm (36.0 in.)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53.5 kg (117.9 lbs.)
Lamp
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1500 W short arc discharge
Approved lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Osram HTI 1500W/60/P50
Color temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6000 K
CRI (Color rendering index). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>85
Average lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .750 hours
Hot restrike . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Semi-hot
Socket:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PGJ50
Ballast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Electronic
Dynamic Effects
Color mixing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CMY, independently variable 0 - 100%
Color temperature control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CTO, variable 6000 - 3200 K
Color wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 interchangeable dichroic filters + open, indexing,
Framing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Continuously rotatable framing module with 4
Rotating gobos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotating gobo wheel with 5 interchangeable rotating
Gobo animation . . . . . . . . . . . . . . . . . . . . . . . . . . . Interchangeable animation wheel, indexing, continuous
Beam effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interchangeable frost filter
Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 - 100%, pulse effects
Mechanical dimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 - 100%
Mechanical shutter. . . . . . . . . . . . . . . . . . Strobe effect 2 - 10 Hz, pulse effects, instant open and blackout
Focus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 m to infinity
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.5° - 55°
Pan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540°
Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268°
Position correction system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute position monitoring
continuous rotation, random color
individually controllable blades
gobos + open, indexing, continuous gobo rotation, shake
rotation with variable angle, speed and direction
Control and programming
DMX channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33/40
Setting and addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control panel with backlit graphic display
RDM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Implemented
16-bit control . . . . . . . . . . . . . . . .Dimmer, gobo indexing (gobo wheels 1 and 2), focus, zoom, pan and tilt
Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U SITT DMX512-A
Fixture identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Four-digit user-settable ID number
Receiver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Opto-isolated RS-485
Firmware update . . . . . . . . . . . . . . . . . . . . . . . . . . . USB memory device or USB/DMX hardware interface
Photometric data
Standard lens, zoom at minimum
Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22%
One tenth-peak angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11°
Total output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31500 lm
Specifications 65
Page 66
Standard lens, zoom at median
Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23%
One tenth-peak angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32°
Total output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33300 lm
Standard lens, zoom at maximum
Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23%
One tenth-peak angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53°
Total output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33800 lm
Measurement source: Osram HTI 1500W/60/P50 Measurement conditions: 227 V, 50 Hz, no effects applied
Construction
Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Black
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Magnesium alloy, UV-resistant fiber-reinforced composite
Reflector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Glass, cold light
Protection rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IP20
Gobos
Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E
Outside diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37.5 mm (1.5 in.) +0/- 0.2 mm (0.01 in.)
Maximum image diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mm (1.2 in.) +/- 0.4 mm (0.02 in.)
Maximum thickness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 mm (0.04 in.) +/- 0.1 mm (0.004 in.)
Recommended glass. . . . . . . . .Borosilicate 3.3 or better with dichroic or heavy matted aluminum coating
Gobo animation wheel
Outside diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133.9 mm (5.3 in.) +/- 0.1 mm (0.004 in.)
Image outer diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 mm (5.1 in.)
Image inner diameter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 mm (1.3 in.)
Thickness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 mm (0.04 in.) +/- 0.1 mm (0.004 in.)
Recommended glass. . . Borosilicate 3.3 or better with dichroic or normal/double mirror aluminum coating
Installation
Mounting points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 pairs of 1/4-turn locks
Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Any
Minimum distance from illuminated surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 m (100 in.)
Minimum distance from combustible materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.2 m (8 in.)
Connections
AC power input . . . . . . . . . . . . . . . . . . . . . . . . . . . Neutrik PowerCon connector with 3 m (9.8 ft.) cable tail
DMX and RDM data in/out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-pin locking XLR
Ethernet (Artnet II compatible, ACN-ready). . . . . . . . . . . Neutrik RJ-45 socket (accepts Neutrik EtherCon
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .connectors in housing)
USB devices (including USB memory storage) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB host socket
Future USB options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .USB de vice socket
Electrical
AC input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 m trailing cable w/o cord cap
AC power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200-240 V nominal, 50/60 Hz
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .auto-ranging electronic switch-mode
Main fuse for 200 - 240 V power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 AT (x 2)
Typical power and current
200 V, 50 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1801 W, 9. 0 A, PF 0.996
200 V, 60 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1805 W, 9. 1 A, PF 0.995
208 V, 60 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1802 W, 8. 8 A, PF 0.994
220 V, 50 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1788 W, 8. 2 A, PF 0.994
230 V, 50 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1783 W, 7. 8 A, PF 0.993
240 V, 50 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1779 W, 7. 5 A, PF 0.989
240 V, 60 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1786 W, 7. 5 A, PF 0.987
Measurements made at nominal voltage. Allow for a deviation of +/- 10%. PF = power factor
66 MAC III Performance user manual
Page 67
Thermal
Maximum ambient temperature (Ta) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40° C (104° F)
Maximum surface temperature, steady state, T
Cooling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Filtered forced air (temperature-regulated, low noise)
Total heat dissipation (calculated, +/- 10% at 200 V, 60 Hz) . . . . . . . . . . . . . . . . . . . . . . . . . . 6160 BTU/hr
= 40° C . . . . . . . . . . . . . . . . . . . . . . . . . . 170° C (338° F)
a
Approvals
EU EMC. . . . . . . . . . . . . . . . . . . .EN 55 103-1, EN 55 015, EN 61 547
EU safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .EN 60598-2-17
US safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ANSI/UL 1573
Canadian safety. . . . . . . . CAN/CSA-E60598-1, CAN/CSA-E598 -2-17
Included items
Osram HTI 1500W/60/P50 lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 97010326
3 m (9.8 ft.) 12 AWG, SJT power cable with Neutrik PowerCon NAC3FCA cable connector P/N 11541503
Tribal Waves gobo animation wheel (installed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 62 325143
2 omega clamp attachment brackets with quarter-turn fasteners . . . . . . . . . . . . . . . . . . 2 x P/N 91602001
User manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 35000247
Accessories
Philips MSR Gold 1500 Fastfit lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 97010340
MAC III Projection Module Kit (converts MAC III Performance to MAC III Profile). . . . . . . . . P/N 91614033
Four-facet prism in holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 62329120
Hole Lot of Fun gobo animation wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91611354
Radial Waves gobo animation wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91611355
Clouds Go By gobo animation wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91611356
Flick It gobo animation wheel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91611357
Half-coupler clamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91 602005
G-clamp (suspension with yoke vertically downwards only) . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91602003
Quick-trigger clamp (suspension with yoke vertically downwards only). . . . . . . . . . . . . . . . . P/N 91 602007
Omega clamp attachment bracket with 1/4-turn fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91602001
T-shaped omega clamp attachment bracket with 1/4-turn fasteners . . . . . . . . . . . . . . . . . . . P/N 91602008
Swing-wing truss mounting plate with half-couplers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91602010
Super Truss 20.5" mounting plate with half-couplers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91602014
Safety wire, 70 kg SWL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91604004
MAC III flightcase. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91 510080
Spare parts
Osram HTI 1500W/60/P50 lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 97010326
Base air filter, short . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 20800220
Base air filter, long. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 20800230
Head air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 20800240
Neutrik PowerCon NAC3FCA cable connector for power cable. . . . . . . . . . . . . . . . . . . . . . . P/N 05342804
16 AT (slow blow) fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 05020047
Related Items
Martin Universal USB-DMX Interface Box™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90702045
Ordering information
MAC III Performance in cardboard packing case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90206200
MAC III Performance in flightcase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 902062 10
MAC III Framing Module Kit (converts MAC III Profile to MAC III Performance) . . . . . . . . . . P/N 91614032
Specifications subject to change without notice. For the latest product specifications, see www.martin.com
Specifications 67
Page 68
Intellectual Property Rights
MAC III™ products are covered by one or more of these patents: US 6,241,366; EP 1234197; US 6,601,973; US 6,687,063; US 6,971,770; US 7,222,997; US 7,498,756; US 7,559,676; US
7,654,693 and/or one or more of these patent applications: CN 1985125A; EP 1747399 (A1); CN 101430073A; EP 2058589; US 2009/0122548; US 12/767,941; CN 101431847A; EP
2091302; US 2009/0196627; CN 200810128771.3; EP 2103864; CN 200810128777.0; US 12/107,827; CN 200810125884.8; DK PA2008/00410; EP2117284; US 12/107,833; CN 200810125883.3; EP2112431; US 2009/0268467; CN 101430070A; EP
2113714; US 2009/0273763; CN 10143554 A; EP 2133626; US 2009/0303724; CN101430076A; EP 2136136; US 2009/0310375; EP 2146141; US 2010/0008080; PCT/DK2010/050081; DK PA2009 01015; DK PA2010 00034
and/or one or more other intellectual property rights, including one or more intellectual property rights listed on www.martin.com/ipr
Disposing of this product
Martin™ products are supplied in compliance with Directive 2002/96/EC of the European Parliament and of the Council of the European Union on WEEE (Waste Electrical and Electronic Equipment), as amended by Directive 2003/108/EC, where applicable.
Help preserve the environment! Ensure that this product is recycled at the end of its life. Your supplier can give details of local arrangements for the disposal of Martin products.
This product contains two batteries. Ensure that they are disposed of responsibly by an authorized recycling or waste disposal center at the end of their life. Where applicable, Martin participates in schemes whose aim is to ensure that local recycling and/or waste disposal centers accept batteries from Martin products.
Page 69
Page 70
Page 71
Page 72
www.martin.com Olof Palmes Allé 18 8200 Aarhus N • Denmark
Tel: +45 8740 0000 Fax +45 8740 0010
Loading...