Page 1
Mania EFX Series
user manual
EFX500 EFX600
EFX700 EFX800
Page 2
Dimensions
Measurements are expressed in millimeters.
EFX500
EFX600
410
410
500
500
180
230
180
230
EFX700 & EFX800
400
© 2006 Martin Professional A/S, Denmark.
All rights reserved. No part of this manual may be reproduced, in any form or by any means,
without permission in writing from Martin Professional A/S, Denmark.
P/N 35000178 Rev. C
500
140
230
Page 3
Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Physical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Creating a data link for DMX and synchronized operation . . . . . 12
Gobo wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Music trig, auto trig and DMX modes . . . . . . . . . . . . . . . . . . . . . 16
Synchronized music trig and auto trig operation . . . . . . . . . . . . 17
DMX controller operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Changing personality settings . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Inverting effects movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Error messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Restriking the discharge lamp . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Adjusting focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Service and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Lamp replacement and adjustment . . . . . . . . . . . . . . . . . . . . . . 27
Replacing the main fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Firmware and hard boot uploads . . . . . . . . . . . . . . . . . . . . . . . . 31
Circuit board layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Control panel overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Mania EFX500 DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Mania EFX600 DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Mania EFX700 DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Mania EFX800 DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Mania EFX Series specifications . . . . . . . . . . . . . . . . . . . . . . . 48
Page 4
Overview
A
B
C
D
E
F
G
A: Power inlet
B: Voltage selector switch (EFX600, EFX700 &
EFX800: fitted to EU models only)
C: DMX in
D: DMX out
E: Display and control buttons
F: Safety cable attachment point
G: Power on/off switch
4 Mania EFX user manual
Page 5
Introduction
Thank you for selecting a dynamic lighting fixture from the Martin Mania
EFX Series. This series consists of DJ lighting fixtures with a motorized
rotating parabolic mirror dish and a motorized rotating gobo wheel (gobos
are outlines or masks placed in a light beam). The fixtures project
complex moving colored flower effects.
The EFX500 and EFX600 feature an additional mirror drum with
motorized pan (swivel) and tilt (rotation) that further enhances beam
dynamics. The EFX800 features an additional motorized tilting (rotating)
color paddlewheel that further enhances beam dynamics and color.
All Mania EFX fixtures offer the following features:
• St and-alone single fixture and synchronized (master/slave) operation in
auto and music triggering modes
• Adjustable music triggering sensitivity
• DMX control with two DMX modes: DMX mode 2 gives extended
functionality on additional channels
• Adjustable focus
The EFX500 uses a long-life 250 watt halogen lamp. All other Mania
EFX fixtures use a long-life 150 watt discharge lamp.
Safety information
Warning! This product is not for household use. It presents risks of
lethal or severe injury due to fire and heat, electric shock,
ultraviolet radiation, lamp explosion and falls.
This product presents risks of lethal or severe injury due to fire and heat,
electric shock, ultraviolet radiation, lamp explosion, and falls. Read this
manual before installing or powering the fixture, follow the safety
precautions listed below and observe all warnings in this manual and on
the fixture. If you have any questions about how to operate the fixture
safely , please contact your Martin dealer or call the Martin 24-hour service
hotline.
Protecting yourself and others from electric shock
• Ensure that the fixture is electrically connected to ground (earth).
Introduction 5
Page 6
• Check the fixture’s voltage setting switch (if fitted) and serial number
label before applying power. Only use the fixture if the fixture’s voltage
setting matches your local AC power voltage.
• Disconnect the fixture from AC power before removing or installing the
lamp, fuse, or any part, and when not in use.
• Use only a source of AC power that complies with local building and
electrical codes and has both overload and ground-fault (earth leakage)
protection.
• Refer all service not described in this manual to a Martin service
technician.
• Do not expose the fixture to rain or moisture.
• Do not operate the fixture if any covers or components are missing,
damaged or deformed.
• Do not use the product if the power cable is damaged. Replace the
cable with a Martin item only (available from your Martin dealer).
Protecting yourself and others from burns and fire
Warning! Hot lamp. The exterior of the fixture can become hot. Allow to
cool for at least 10 minutes before handling or opening.
• Surface temperature under steady state condition = 100°C (212° F).
• Do not operate the fixture if the ambient temperature (T
) exceeds 40° C
a
(104° F).
• Never attempt to bypass the thermostatic switch or fuses. Always
replace defective fuses with ones of the specified type and rating.
• See serial label for replacement fuse size and lamp type.
• Keep all combustible materials (for example fabric, wood, paper) at
least 0.3 meters (4 inches) away from the fixture. Keep flammable
materials well away from the fixture.
• Do not illuminate surfaces within 1 meter (3.3 feet) of the fixture.
• Provide a minimum clearance of 0.1 meters (4 inches) around fans and
air vents and ensure that air flow through and around vents is free and
unobstructed.
• Never place filters or other materials over the lens or in the optical path.
• Do not look directly into the light.
• Change the lamp immediately if it becomes damaged or thermally
deformed.
• Do not operate the fixture if any optical components or shields are
missing, damaged or deformed: an unshielded discharge lamp emits
dangerous UV radiation that can cause burns and eye injuries.
• Do not modify the fixture or install other than genuine Martin parts.
6 Mania EFX user manual
Page 7
Preventing injuries due to falls
• When suspending the fixture above ground level, verify that the
structure can hold at least 10 times the weight of all installed devices.
• Ensure that all external covers and rigging hardware are securely
fastened and use an approved means of secondary attachment such as
a safety cable.
• Block access below the work area and work from a stable platform
whenever installing or removing the fixture.
Unpacking
Important! Do not lift or carry a fixture by holding the motor housing (if
fitted) on the front of the fixture. It is not designed for this
purpose. You could injure yourself or others, and you could
cause damage that is not covered by the product guarantee.
The packing material is carefully designed to protect the fixture during
shipment - always use it to transport the fixture.
Mania EFX fixtures are supplied with the following items:
• 3-wire power cable(s) with IEC power input connector.
• 5m (16.4 ft.) DMX cable.
• Mounting plate (installed).
• EFX500 only: 250 watt halogen lamp (installed).
• EFX600, EFX700 and EFX800: 150 watt discharge lamp (this is
supplied separately to avoid damage during shipping and must be
installed before use – see “Installing a discharge lamp” on page 29).
Removing protective packaging
Important! The EFX500 and EFX600 mirror drum
is secured with packaging and white
plastic ties for shipment. Wearing
gloves to avoid cutting yourself on
the mirrors, cut and remove the
plastic ties. Check that the drum can
be swivelled through 180° and rotated
through 360° before operating the
fixture. If it cannot, you may have
missed one of the plastic ties.
Remove the clear protective film from
the mirror drum before operating the fixture.
Introduction 7
Page 8
Installation
AC power
Warning! Ensure that the fixt ure’s voltage setting matches your local AC
power voltage before applying power.
For protection from fire and electric shock, the fixture must be grounded
(earthed). The power supply must have both overload and ground-fault
(earth fault) protection.
Check that power cables are undamaged and rated for the current
requirements of all connected devices before use.
Important! Do not connect the fixture to a dimmer system, as this may
cause damage that is not covered by the product guarantee.
Mania EFX500 power settings
All Mania EFX500 models must be set to 115 V, 60 Hz or 230 V , 50 Hz AC
power using the red voltage selector switch on the connections panel.
• Set the switch so that 115 V is visible if you have110-120 V, 60 Hz AC
power.
• Set the switch so that 230 V is visible if you have 220-240 V, 50 Hz AC
power.
Mania EFX600, EFX700 & EFX800 power settings
• Mania EFX600, EFX700 and EFX800 EU models can be set to 230 or
240 V, 50 Hz AC power using the switch on the connections panel. Use
the 230 V setting if you have 220-230 V power, and use the 240 V
setting if you have 230-240 V.
• Mania EFX600, EFX700 and EFX800 US models do not have a voltage
selector switch and are supplied set up for 110-120 V, 60 Hz AC power.
Warning! Do not operate the fixture if local AC power v olta ge is outside the
range specified for the fixture.
Power plugs
Mania EFX fixtures are supplied with power cables to match most local
power outlet sockets (see “Included items” on page 50), but if there is no
8 Mania EFX user manual
Page 9
power plug that matches your socket type, install a suitable groundingtype (earthed) power plug on the power cable. Consult a qualified
electrician if you have any doubts about proper installation.
Follow the power plug manufacturer’s instructions, connecting the
appropriate wires to ground (earth), live, and neutral. The table below
shows some common wire identification schemes.
Function Wire (EU) Wire (US) Marking Screw color
live brown black “L” yellow or brass
neutral blue white “N” silver
ground (earth) yellow/green green green
Table 1: Cord cap wiring
Physical installation
Each Mania EFX fixture must be either:
• fastened to an overhead structure by means of its mounting plate and a
Martin rigging clamp (available from your Martin dealer), or
• fastened to a surface by means of its mounting plate and suitable bolts.
Do not install the fixture by any other means, as this can cause the fixture
to overheat.
Ensure that the mounting structure or surface and all fasteners used can
support at least 10 times the weight of all installed fixtures, clamps,
cables, auxiliary equipment, etc.
Ensure that the fixture is located:
• at least 1 meter (3.3 ft.) away from the surface to be illuminated,
• at least 0.1 meters (4 in.) from any combustible materials (wood, fabric,
paper, etc.) and
• well away from any flammable materials.
Ensure that the clearance around the fan and air vents is at least 0.1
meters (4 in.) and that airflow is free and unobstructed.
Warning! Block access below the work area and work from a stable
platform when installing or servicing the fixture.
Always use a secure means of secondary attachment that can
hold at least 10 times the weight of the fixture, looping it
through the attachment point shown at F in “Overview” on
page 4. Do not simply pass the secondary attachment around
the mounting plate, as this will leave the fixture unsecured.
Installation 9
Page 10
Beam angles and fixture orientation
The fixtures in the Mania EFX series have different optical configurations.
Referring to the illustration below will help you decide how to orient your
fixture.
EFX500, EFX600 EFX700 EFX800
Surface mounting
To mount the fixture on a surface, you will need four grade 8.8 (minimum)
8mm diameter, 13mm head hex screwbolts (or similar type fasteners of
the same grade and size) and an eyebolt for the safety cable.
Installing the mounting plate separately
Surface mounting is easiest if you detach the mounting plate from the
fixture, bolt the mounting plate to the surface, and then reattach the
fixture. If you choose this method, access for reattachment and
adjustment can be easier if you remove the swivel locks and replace them
with two M8 hexagonal lock nuts (P/N 08132701). Install an eyebolt and
safety attachment once the fixture is mounted.
Installing the fixture and mounting plate as a unit
If you prefer to install the fixture and mounting plate without separating
them:
1. Using the inside back cover of this manual as a guide, drill three holes
in the positions marked A.
10 Mania EFX user manual
Page 11
2. Screw three grade
max
13mm
/
½"
Ø8mm
8.8 (minimum)
8mm diameter,
13mm head hex
screwbolts or bolts
into the holes at A,
but do not tighten
them fully –allow
enough clearance
between the bolt
head and surface
for the 3mm thick
mounting plate.
3. Fold the mounting
plate so that it lies flat against the back of the fixture and tighten the
swivel locks. For easier access for adjustment, it is possible to remove
the swivel locks and replace them with two M8 hexagonal lock nuts,
P/N 08132701).
4. Hold the fixture up to the surface so that the screwbolt heads pass
through the centers of the keyholes A in the mounting plate, and slide
the fixture to engage the screwbolt heads in the mounting plate.
max 13mm / ½"
A
A
5. Using one of the remaining holes in the mounting plate as a guide,
mark a position for a fourth hole to accept a screwbolt that will lock the
fixture in place.
6. Remove the fixture from the surface, drill the fourth hole and replace
the fixture on the surface as described in point 4 above. Screw the
fourth screwbolt through the mounting plate into the surface to lock the
fixture in place, using a washer on the screwbolt if necessary.
7. Install an eyebolt and safety attachment once the fixture is mounted.
Overhead mounting
To hang a fixture on an overhead structure:
1. If using a rigging clamp, ensure that the clamp is undamaged and can
bear at least 10 times the fixture’s weight. Bolt the clamp securely to
the fixture’s mounting plate with a grade 8.8 (minimum) M12 bolt and
lock nut through one of the 13 mm holes provided, or as recommended
by the clamp manufacturer. The clamp must be attached centrally in
the mounting plate to distribute the load evenly .
Installation 11
Page 12
2. Working from a stable
platform, clamp or fasten the
fixture to the structure.
3. Install a safety cable that can
hold at least 10 times the
weight of the fixture.
4. Loosen the swivel locks, tilt
the fixture to the desired
angle, and retighten.
Important! Check to make sure that the EFX500 and EFX600 mirror drum
cable does not rub on the mounting plate. If necessary, reverse
the mounting plate (see illustration).
Creating a data link for DMX and
synchronized operation
You need a serial data link to:
• run light shows on one or more fixtures using a DMX controller, or
• run synchronized light shows on two or more fixtures (master/slave
operation).
Fixtures on a serial data link must be daisy-chained in one single line,
maximum 500 meters (1640 ft.) long, with maximum 32 fixtures on the
link. If you wish to exceed 32 fixtures or 500 meters, or to split the link into
branches, use an optically isolated amplifier-splitter such as the Martin
RS-485 Opto-Splitter (P/N 90758060).
Reliable data connection requires suitable cable. Standard microphone
cable cannot transmit DMX data reliably over long runs. For best results,
use cable with at least one twisted pair specifically designed for RS-485
applications. Your Martin dealer can supply suitable high quality cable in
various lengths.
Connecting the serial data link
The Mania EFX has XLR data connectors, wired with pin 1 to ground, pin
2 to signal - (cold), and pin 3 to signal + (hot). This is the standard
configuration for DMX devices.
One or more adaptor cables may be required to connect a Mania EFX
fixture to the controller and/or other types of fixture, because some
devices may have 5-pin XLR connectors, and others may have reversed
12 Mania EFX user manual
Page 13
signal polarity (pin 2 hot and pin 3 cold). Connector polarity is normally
specified on the device or in the device’s user manual.
5-pin to 3-pin
Adaptor
Male Female
1
2
3
4
5
P/N 11820005
1
2
3
To connect the data link:
1. Power all devices off.
2. If you intend to use a DMX controller, run a data cable from the DMX
3-pin to 5-pin
Adaptor
Male Female
1
2
3
P/N 11820004
1
2
3
4
5
3-pin to 3-pin
Phase-Reversing
Adaptor
Male Female
1
2
3
P/N 11820006
1
2
3
Male
Termination Plug
Male XLR
1
2
120 Ohm
3
P/N 91613017
Female DMX
Termination Plug
Female XLR
1
2
120 Ohm
3
P/N 91613018
DMX connectors and polarity
controller’s data output to the first fixture’s data IN socket. If the
controller has a 5-pin output, use a 5-pin male to 3-pin female adaptor
cable (P/N 11 820005).
3. If you intend to run fixtures in master/slave operation, insert a female
DMX termination plug (P/N 91613018) in the first fixture’s data IN
socket.
4. Plug a data cable into the OUT socket of the first fixture and the IN
socket of the next one. Continue connecting up to 32 Mania EFXs
output-to-input.
5. Terminate the link by inserting a male termination plug (P/N 91613017)
into the data output of the last fixture. A termination plug is simply an
XLR connector with a 120 Ohm, 0.25 W resistor soldered across pins 2
and 3.
Gobo wheels
All Mania EFX fixtures contain a gobo wheel. Note that it is the whole
wheel, and not the individual gobos, that rotates. Rotating gobo image
effects are created by the mirror dish.
• The EFX500 has 11 colored gobos plus blackout.
• The EFX600 has 12 colored gobos.
• The EFX700 has 12 colored gobos.
• The EFX800 has 12 gobos. Color is provided by the color paddlewheel.
Installation 13
Page 14
The Mania EFX500 contains the gobo wheel shown below.
1
2
3
4
5
6
7
8
9
10
11
12
12
11
1
9
10
8
7
5
2
3
4
6
EFX500 Gobo wheel
The Mania EFX600 contains the gobo wheel shown below.
14 Mania EFX user manual
EFX600 Gobo wheel
Page 15
The Mania EFX700 contains the gobo wheel shown below.
12
11 1
2
3
4
9
10
8
7
5
6
EFX700 Gobo wheel
The Mania EFX800 contains the gobo wheel shown below.
12
11
1
9
10
2
3
8
7
5
4
6
EFX800 Gobo wheel
Installation 15
Page 16
Operation
Getting started
Mania EFX fixtures are supplied in DMX mode with DMX address set to 1.
If you want to operate a fixture without a DMX controller, you need to set it
to music trig or auto trig mode before use (see “Selecting DMX, music trig
or auto trig operating modes” on page 17).
Powering on
Once the fixture is correctly and safely installed, power on at the fixture’s
power on/off switch. The fixture will start up and reset.
If the fixture resets successfully, the software version installed will appear
in the fixture’s display. For example, if software version 1.00 is installed,
the message
100 should appear in the display.
Once the fixture has reset, the fixture will display either its DMX address,
901 (music trig mode) or 900 (auto trig mode).
If any other message is displayed, the fixture has detected an error (see
“Error messages” on page 24). If this occurs, switch off, wait a few
seconds and switch on again. If the error message appears again, consult
your Martin dealer.
Music trig, auto trig and DMX
modes
Mania EFX fixtures have three main operating modes:
Music trig mode: In this mode, lighting effects are triggered by music
intensity. Multiple fixtures can be synchronized if one master fixture is set
to music trig mode and the other fixtures are set to DMX mode.
Auto trig mode: In this mode, the fixture runs a factory-set dynamic light
show that uses all the fixture’s effects in a random program. Multiple
fixtures can be synchronized if one master fixture is set to auto trig mode
and the other fixtures are set to DMX mode.
16 Mania EFX user manual
Page 17
DMX mode: In DMX mode, fixtures receive control instructions via the
X100 X10 X1 Mode
DMX Address
serial data link. They will respond to control signals from a DMX controller
(or from another fixture set as master).
Selecting DMX, music trig or auto trig operating
modes
Fixtures are supplied set to DMX mode with DMX address set to 1. If you
intend to operate the fixture without a DMX controller, you need to set the
fixture to music trig or auto trig mode.
To switch between DMX, auto trig and music trig modes:
1. Apply power to the fixture and wait
while it resets. If the fixture is in DMX
mode, the display will show the
fixture’s DMX address.
2. Press the [Mode] button once. The
fixture enters auto trig mode and
appears in the display.
900
3. Press the [Mode] button again once.
The fixture enters music trig mode,
901 appears in the display.
and
4. Press the [Mode] button again once to
return to DMX mode. The fixture’s
DMX address appears in the display.
The fixture will return to the mode you have set when it is powered off and
on.
If you set the fixture to music trig mode but it does not respond
satisfactorily to the music beat, adjust the music trig sensitivity level (see
“Adjusting music trig sensitivity” on page 22).
[Mode] button
Synchronized music trig and auto
trig operation
You can set multiple fixtures on a serial data link to respond together to a
music trig or auto trig signal from one fixture. This feature allows
synchronized operation without a DMX controller. The fixture sending the
signal is the ‘master’ fixture and the fixtures that receive the signal are the
‘slave’ fixtures.
Important! Set only one fixture as master: damage can occur if two master s,
or a master and a DMX controller, are linked.
Operation 17
Page 18
Setting up synchronized operation
X100 X10 X1 Mode
DMX Address
To set up fixtures for synchronized operation:
1. Ensure that all fixtures on the data link are in DMX mode.
2. Select one fixture to be the master and set it to auto trig or music trig
mode (see “Selecting DMX, music trig or auto trig operating modes” on
page 17)
3. When a slave fixture receives signals from the master, it will
automatically begin operating in slave mode.
display and the green Data LED will light to show that the fixture is
receiving control data.
910 will appear in its
Slave mode
Data LED lit
[Mode] button
Fixtures return to their DMX/auto trig/music trig settings when powered off
and on, so you should only need to set fixtures as masters/slaves once.
DMX controller operation
Setting DMX mode 1 or 2
T wo DMX modes are available: DMX mode 1 (normal) and DMX mode 2
(extended). Mode 2 uses two extra DMX channels that allow you to select
pre-programmed macros and set the speed of effects movement from the
DMX controller. The fixture is supplied set to DMX mode 2.
•The EFX500 uses seven DMX channels in DMX mode 1 and nine
channels in DMX mode 2.
•The EFX600 uses six DMX channels in DMX mode 1 and eight
channels in DMX mode 2.
•The EFX700 uses four channels in DMX mode 1 and six channels in
DMX mode 2.
18 Mania EFX user manual
Page 19
• The EFX800 uses five DMX channels in DMX mode 1 and seven
X100 X10 X1 Mode
DMX Address
X100 X10 X1
oMode
DMX Address
channels in DMX mode 2
To toggle between DMX modes 1 and 2:
1. Apply power to the fixture and wait for
the fixture to reset.
2. Hold the [Mode] button pressed in for 5
seconds to enter the fixture control
menu.
3. Press the [X100] button repeatedly until
0 appears in the left of the display.
Press the [X1] button to toggle between
DMX mode 2
1 (to set DMX mode 1) and 2 (to set
DMX mode 2) in the right of the display.
4. Press the [Mode] button again to save your setting.
Setting DMX addresses
If you intend to use a DMX controller, you will need to set the DMX
address for each fixture. The DMX address, also known as the start
channel, is the first channel used to receive instructions from the
controller. It is set using the three addressing buttons on the fixture’s
control panel.
For individual control, each fixture must be assigned its own DMX address
and control channels. Control channels must not overlap with those of
other fixtures. Fixtures of the same type with the same DMX address will
receive the same instructions and behave identically.
As an example, a Mania EFX500 set to DMX mode 2 will use 9 channels.
If you give it DMX address 100, it will use channels 100 , 101, 102, 103,
104, 105, 106, 107 and 108. Channel 109 is available for the next fixture.
The default factory-set DMX address is ‘1’.
To set a fixture’s DMX address:
1. Decide on suitable DMX addresses for all
the fixtures on the data link (note that 512
channels are available in one DMX
universe).
2. Apply power to the fixture and wait while it
resets.
M
DMX addressing
buttons
Operation 19
Page 20
3. Use the three addressing buttons on the fixture’s control panel to enter
the DMX address. The [X1] button increases the last digit in the DMX
address, the [X10] button increases the address by 10 and the [X100]
button increases the address by 100.
Fixtures remember their DMX address when they are powered off and on.
DMX control options
See also the DMX protocols starting on page 37 for an overview of DMX
commands and channels.
Control options
In DMX modes 1 and 2, the following functions can be controlled on all
models:
Strobe effect: A strobe effect with variable flash rate can be selected.
Auto trig: While in DMX mode, the Mania EFX can be remotely set to
auto trig.
Reset:
using channel 1. The reset command must be sent for 5 seconds before it
takes effect.
When a fixture is reset via DMX,
Dimming: The Mania EFX500 can be dimmed from 0% (blackout) up to
100% intensity using channel 2. All other Mania EFX fixtures can be
dimmed from 0% to 100% using the shutter on channel 1.
Gobo wheel position, rotation and music trig: The gobo wheel can be
positioned to project one of the gobos (or at blackout on the EFX500). The
gobo wheel can also be spun in either direction or set to music trig, in
which gobos change with the music beat.
Mirror dish rotation and music trig: The mirror dish can be spun in
either direction for dynamic projection effects or set to music trig.
In DMX mode 2, the following additional functions can be controlled on
two extra channels:
Macros: On the first extra channel, you can select one of twelve factoryset macros. Macros are pre-programmed dynamic shows that use all the
fixture’s effects.
All effects can be reset to their index positions from the controller
800 should appear in the digital display.
Effect speed: On the second extra channel, you can either select the
speed at which effects change or select tracking. Selecting a speed allows
you to adjust fade times when using DMX controllers that do not feature
20 Mania EFX user manual
Page 21
fade time programming (a fade time is the time taken for effects to change
DMX Address
from one scene to the next). If you select tracking, the DMX controller
defines fade times.
EFX500 and EFX600 models only
Pan: The mirror drum pans (swivels) approx. 180°. A pan position can be
selected, pan can be set to narrow or wide shake, or pan can be set to
music trig.
Tilt: The mirror drum tilts (rotates) 360°. The drum can be held in a
stationary position, set to rotate in either direction, set to narrow or wide
shake, or set to music trig.
EFX800 models only
Tilt: The color paddlewheel tilts (rotates) 360°. The paddlewheel can be
held in a stationary position, set to rotate in either direction, set to narrow
or wide shake, or set to music trig.
Unsure about speed and tracking?
Set the fixture to tracking if you are using programmed fade times or
macros on your DMX controller. Select an effects speed if you are not
using programmed fade times or macros on your DMX controller.
However, if you are using fade times on your controller and have set the
fixture to tracking, but effects movement is rough and irregular, setting
fade times on your controller to zero and selecting an effects speed may
give smoother movement.
Effects movement is set to ‘tracking’ if the fixture is in DMX mode 1 and by
default.
DMX signal indicator
When a Mania EFX fixture
receives a valid DMX
signal, the green Data
LED will light to show that
the fixture is receiving
control data.
DMX signal received
Data LED
lit
Operation 21
Page 22
Changing personality settings
X100 X10 X1 Mode
DMX Address
X100 X10 X1 Mode
DMX Address
You can change certain personality settings using the buttons on the
control panel:
• on all models, you can adjust music trig sensitivity
• on the EFX500 and EFX600, you can invert mirror drum rotation
• on the EFX800, you can invert color paddlewheel rotation
To change these personality settings:
• Hold the [Mode] button pressed in for 5 seconds to access the control
menu.
• Use the [X100] button to select the personality feature.
• Use the [X1] button to change the setting for that feature.
Personality feature Setting
Adjusting music trig sensitivity
The music trig sensitivity can be adjusted on all models for optimum
synchronization with the music. To adjust sensitivity:
1. With the fixture powered on and in music
trig mode, play a typical music track at
typical volume for your location.
2. Hold the [Mode] button on the control
panel pressed in for 5 seconds to enter
the control menu.
3. Press the [X100] button repeatedly until
3 appears on the left of the display.
4. Press the [X1] button to select a music
trig sensitivity setting on the right of the display from
sensitivity) to 9 (maximum sensitivity). The default setting is 6 .
1 (minimum
5. Press the [Mode] button again to save your setting and exit the control
menu.
22 Mania EFX user manual
Page 23
Inverting effects movement
X100 X10 X1 Mode
DMX Address
X100 X10 X1 Mode
DMX Address
You can create symmetrical action across multiple EFX500, EFX600 and
EFX800 fixtures in synchronized and DMX operation by inverting the
effects movement on some fixtures so that they ‘mirror’ the acti on of
others. When one fixture tilts left, for example, a fixture on the other side
of the dance floor can bet set to tilt right.
Inverting tilt on the EFX500, EFX600 and EFX800
To invert tilt (mirror drum rotation on the EFX500 and EFX600, color
paddlewheel rotation on the EFX800):
1. Power the fixture on.
2. Hold the [Mode] button on the control
panel pressed in for 5 seconds to enter
the control menu.
3. Press the [X100] button repeatedly until
2 appears on the left of the display.
4. Press the [X1] button to change the tilt
setting on the right of the display from
(normal tilt) to 1 (inverted tilt).
5. Press the [Mode] button again to save
your setting and exit the control menu.
0
Inverting pan on the EFX500 and EFX600
To invert pan (mirror drum swivel) on EFX500 and EFX600 fixtures:
1. Power the fixture on.
2. Hold the [Mode] button on the control
panel pressed in for 5 seconds to enter
the control menu.
3. Press the [X100] button repeatedly until
1 appears on the left of the display.
4. Press the [X1] button to change the pan
setting on the right of the display from
(normal pan) to
5. Press the [Mode] button again to save
your setting and exit the control menu.
1 (inverted pan).
0
Operation 23
Page 24
Error messages
In the event of an error, the following messages appear in the fixture
display:
701 Gobo wheel error (all fixtures). There is a problem with the gobo
wheel positioning system.
702 Hot restrike protection (EFX600, EFX700 and EFX800). You have
tried to restrike a lamp by DMX within 8 minutes of extinguishing the lamp
via DMX.
703 Color paddlewheel error (EFX800). There is a problem with the
color paddlewheel positioning system.
If an error message is displayed, try powering the fixture off and then on
again to reset it. If the problem persists, contact your Martin dealer.
Restriking the discharge lamp
If the discharge lamp in the EFX600, EFX700 and EFX800 is powered off
via DMX during operation, you must wait eight minutes before the lamp
can be restruck.
If you try to strike the lamp anyway, the message
display.
702 will appear in the
24 Mania EFX user manual
Page 25
Adjusting focus
Focus can be adjusted from
approx. 2 meters (6.6 ft.) to
approx. 20 meters (66 ft.) using
the focus adjustment knob.
On EFX500 and EFX600 fixtures,
the focus adjustment knob is close
to the lens aperture in the mirror
drum cutout.
On EFX700 and EFX800 fixtures,
the focus adjustment knob is close
to the beam aperture on the front
plate.
EFX500, EFX600
EFX700, EFX800
Operation 25
Page 26
Service and maintenance
Mania EFX fixtures require simple routine maintenance. The maintenance
schedule depends heavily on the operating environment. Please consult a
Martin service technician for recommendations.
Refer any service procedure not described here to a qualified technician.
Warning! Disconnect the fixture from power and allow it to cool for at
least 10 minutes before removing any cover.
Cleaning
Important! Excessive dust, grease, and smoke fluid buildup degrades
performance and causes overheating and damage to the
fixture that is not covered by the warranty. Check and, if
necessary, clean fixtures at regular intervals.
Cleaning the fan and air vents
To maintain adequate cooling, dust must be cleaned from the fan and air
vents periodically.
1. Disconnect the fixture from power and allow it to cool for at least 10
minutes.
2. Loosen the lamp cover release thumbscrew and slide and lift the lamp
cover out of the fixture housing. Let the cover hang on its safety strap.
3. Remove the four torx
screws holding the main
cover (see illustration on
right) and slide and lift
the cover out of the
housing. Let the cover
hang on its safety strap.
4. Remove dust and dirt
from the fan blades and
vent grills using a soft
brush, cotton swab,
vacuum, or compressed air.
5. Reinstall the main cover and lamp cover securely before reapplying
power.
26 Mania EFX user manual
Page 27
Cleaning optical components
Use care when cleaning
optical components. The
coated surfaces are fragile
and even small scratches
may be visible in the
fixture’s light output.
1. Disconnect the fixture
from power and allow it to
cool for at least 10
minutes.
2. Open the covers as
described in “Cleaning
the fan and air vents”
above.
3. Blow or vacuum away
loose dust. Remove dirt
from lenses, gobos and
mirror wheel with a soft
cloth or cotton swabs
wetted with isopropyl
alcohol. Regular glass cleaner may also be used, but no residues may
remain. To avoid scratches, do not rub. Instead, press repeatedly to lift
dirt off surfaces.
EFX600
EFX700
EFX800
EFX500
EFX500
EFX600
EFX800
Optical path
4. Any remaining residues or streaking can be removed with distilled
water. Mixing the water with a small amount of wetting agent such as
Kodak Photoflo will help prevent streaking and spotting.
5. Dry with a clean, soft, lint-free cloth or compressed air.
6. Reinstall all covers before reapplying power.
Lamp replacement and
adjustment
Warning! Wear safety glasses and gloves and allow the fixture to cool for
at least 10 minutes before replacing the lamp.
Halogen lamp (Mania EFX500)
The Mania EFX500 uses a 250 watt halogen lamp. Replace the lamp
when it reaches the average life specified by the manufacturer. The
halogen lamp has an integral reflector and does not require adjustment
when correctly installed.
Service and maintenance 27
Page 28
Important! Use only this type of lamp. See “Accessories” on page 51 for
details of replacement lamps. Installing any other lamp may
damage the fixture.
Installing a halogen lamp
1. Disconnect the fixture
from power and allow it to
cool for at least 10
minutes.
2. Loosen the lamp cover
release thumbscrew
enough to slide and lift the
lamp cover out of the
fixture housing. The lamp
cover is attached to the
housing with a safety
strap.
3. If replacing an old lamp,
remove it together with its
ceramic socket from the
lampholder clip and, being
careful not to strain any wires, gently pull the lamp off the socket.
4. Hold the new lamp by its base (do not touch any other part of the lamp).
Push the lamp pins squarely into the ceramic socket.
5. If you touched the bulb, the reflector or any optical components, clean
them with a clean, soft, lint-free cloth wetted with isopropyl alcohol and
dry with a clean, soft, lint-free cloth or compressed air.
6. Replace the lamp and socket in the lampholder clip, ensuring that the
reflector sits flat against its plate and is held securely in place. When
installed correctly, the rim of the reflector locates under the heads of
two stop screws so that the reflector is held firmly between these
screws and the lampholder clip.
7. Close the lamp cover, checking that no wires are trapped, and retighten
the thumbscrew.
Discharge lamp (EFX600, EFX700 & EFX800)
The Mania EFX600, EFX700 and EFX800 use a 150 watt long-life
discharge lamp.
For optimum lamp life, always allow discharge lamps to warm up for at
least 5 minutes before dousing.
28 Mania EFX user manual
Page 29
Restriking a discharge lamp
Lamp
adjustment
Lamp
adjustment
Lamp
adjustment
Note that, when a discharge lamp is powered off, it must be allowed to
cool for 8 minutes before it is restruck.
Installing a discharge lamp
Warning! Wear safety glasses and gloves and allow the fixture to cool for
at least 10 minutes before replacing the lamp.
1. Disconnect the fixture from power and allow it to cool for at least 10
minutes.
2. Loosen the screw
holding the lamp
cover (see illustration
on right: EFX600
illustrated) and open
the cover. The cover
is attached to the
housing with a safety
strap.
3. Loosen the four small
screws (see illustration on right)
holding the lampholder and pull
the lampholder gently out of the
fixture. Note which edge faces
outwards, as the lampholder must
be reinstalled in the same
position.
4. If replacing an old lamp, remove it
from its ceramic socket.
5. Hold the new lamp by its base (do
not touch any other part of the
lamp). Push the lamp pins
squarely into the socket.
6. If you touched the bulb, the
reflector or any optical
components, clean them with a
clean, soft, lint-free cloth wetted
with isopropyl alcohol and dry with
a clean, soft, lint-free cl oth or
compressed air.
This edge
faces out
Service and maintenance 29
Page 30
7. Replace the lampholder in the housing, making sure that the edge with
Lamp
adjustment
Lamp
adjustment
Lamp
adjustment
the semicircular cutout in its center faces out towards the edge of the
and reinstall the four screws. Close the lamp cover, checking that no
wires are trapped, and replace the lamp cover screw.
8. Reapply power.
Discharge lamp
adjustment
The discharge lamp alignment can
be adjusted to optimize the
projected image using the
adjustment screws on the
lampholder (see illustration on
right). Experiment with turning the
screws until the brightest part of
the beam is centered in the
projected images.
Replacing the main fuse
Mania EFX fixtures use a slow-blow fuse for protection against current
overload. An indication that the fuse may have blown is that when power
is applied and the lamp is switched on, no light is produced.
If the fuse blows repeatedly, there is probably a fault. Disconnect the
fixture from power and data and contact a Martin service technician.
Never bypass the fuse or replace it with one of another type or rating.
To replace the main fuse:
1. Disconnect the power cable.
2. Pry open the fuse holder next to the
power cable inlet with a flat-head
screwdriver and remove the fuse.
3. Replace the fuse with one of the
same type and rating. Fuse ratings
are listed on serial number labels and
under “Electrical” on page 49.
4. Replace the fuse holder before
30 Mania EFX user manual
reapplying power.
Page 31
Firmware and hard boot uploads
It is possible to upload new firmware to via the data IN connector using,
for example, an uploader such as the Martin MP-2 Uploader, or a PC
using a Martin DABS interface device and suitable software. The latest
firmware versions for Mania EFX fixtures can be downloaded from the
Support area of the Martin website at http://www.martin.com
If a fixture will not accept normal firmware uploads, it can be forced to
accept an upload by starting it in hard boot mode. To start in hard boot
mode, hold both the [Mode] button and the [X100] button pressed in while
powering on the fixture. When the fixture is in hard boot mode, the data
LED blinks.
If you are not sure how to carry out uploads, your Martin dealer will be
able to give advice or carry out the upload for you.
Service and maintenance 31
Page 32
Circuit board layouts
EFX500 Main PCB
J11
J8
J13
J4J2J6J7
J12
Mirror
Dish
Color /
Gobo
Power
BCBA J9
Display PCBA
Power PCBA
J6
MCU
J4J2J6J7
Tilt
J10
J3
DMX
Hall
Sensor
Gobo
Pan
Mirror
Dish
Power
PCB
J9
Tilt
Pan
Color /
Gobo
Display
Mania EFX600 EU / US
Main
PCB
J6J7
J13
J4J2 J16J15
Shutter
J10
Hall
sensor
gobo
J8
DMX
J3
Power
PCB
J6
J12
J17
MCU
EFX500 Main PCB, all models
Display PCBA
EFX500 Main PCB
Power PCBA
J6
Power BCBA J9
Gobo
Hall Sensor
EFX600 Main PCB, all models
Power
32 Mania EFX user manual
PCB
J6
Mania EFX600 EU / US
Main PCB
Mirror
Dish
Mirror
Dish
Color /
Gobo
Color /
Gobo
Hall
sensor
gobo
Power
PCB J9
Page 33
Mirror
Dish
Power
PCB
J9
Color /
Gobo
Display
Mania EFX700 EU / US
Main
PCB
J6J7
J13
J4J2 J16J15
Shutter
J10
Hall
sensor
gobo
J8
DMX
J3
Power
PCB
J6
J12
J17
MCU
EFX700 Main PCB, all models
Mirror
Dish
Power
PCB
J9
Gobo
Display
Mania EFX800 EU / US
Main
PCB
J6J7
J13
J4J2 J16J15
Shutter
J10
Hall
sensor
gobo
J8
DMX
J3
Power
PCB
J6
J12
J17
MCU
Hall
Sensor
Paddle
Wheel
Paddle
Wheel
Mania EFX700 EU / US
Main PCB
Power
PCB
J6
Hall
sensor
gobo
Power
PCB J9
EFX800 Main PCB, all models
Mania EFX800 EU / US
Power
PCB
J6
Paddle
Wheel
Mirror
Dish
Main PCB
Mirror
Dish
Color /
Gobo
Hall
Sensor
Paddle
Wheel
Hall
sensor
gobo
Power
PCB J9
Circuit board layouts 33
Page 34
J5
J8
J7
C1
Toroidal
Transformer
Fan
J3
J1
Voltage Selector
Switch
Main PCBA
J13
Teroidal
Transformer
Lamp
Main
PCBA
J12
J6
J13 J9
Toroidal
Transformer
EFX500 Power PCB, all models
Mania EFX6-7-800
EU
Power
PCB
J2
J5
Main
Filter
J8
Toroidal transformer
Fuse
5A / 250V
J7
J9
J6
C1
Ballast
Main PCB
J13
Fan
Main PCB
J12
J1
J3
Mania EFX6-7-800
US
Power
PCB
J2
J5
Ballast
Capacitor
J8
Toroidal transformer
Fuse
5A / 250V
J7
J9
J6
C1
Transformer
Main PCB
J13
Fan
Main PCB
J12
J1
J3
J12
Main PCBA
Teroidal
Transformer
Toroidal
Transformer
Toroidal
Transformer
Voltage Selector
Switch
Main PCBA
EFX600, EFX700 and EFX800 Power PCB
EU models US models
Toroidal transformer
Main
Filter
Toroidal transformer
Mania EFX6-7-800
EU
Power PCB
5A / 250V
Main PCB
J13
Main PCB
J12
Ballast
Capacitor
J13
Mania EFX6-7-800
US
Power PCB
5A / 250V
Main PCB
J13
Main PCB
J12
34 Mania EFX user manual
Page 35
Troubleshooting
Problem Possible cause(s) Suggested remedy
Shutter closed (EFX600,
No light
No action in music trig mode
EFX700 & EFX800 using
DMX control)
No power to the fixture Check connections
Blown fuse
Burned out lamp Install new lamp
Fixture too hot
Sound too low to activate
control circuit
Open shutter via DMX
If power is applied and the
lamp is switched on but
does not light, check and
replace fuse if necessary
Allow to cool
Improve airflow around
fixture
Adjust music level
sensitivity
Increase music volume
Move fixture closer to music
source
No action in music trig and
auto trig modes
Unsatisfactory action in
synchronized operation
Poor action in a new fixture
Fuse blows repeatedly Electrical malfunction
EFX600, EFX700, EFX800:
Impossible to restrike lamp
after dousing via DMX.
Fixtures reset correctly but
behave erratically or do not
respond during DMX or
synchronized operation
Electrical malfunction
Fixtures incorrectly linked
More than one fixture set as
master
Some transport packaging
has not been removed
8 minute hot restrike
protection delay activated
Data link not terminated
Refer to a Martin service
technician
Check data link connections
between fixtures
Check that all slave fixtures
are set to DMX mode
Remove all plastic ties from
mirror drum until drum
rotates freely
Refer to a Martin service
technician
Wait 8 minutes before
restriking a hot discharge
lamp
Insert DMX termination plug
in output of last fixture on
link. In synchronized
operation, insert DMX
termination plug in input of
first fixture
Troubleshooting 35
Page 36
Control panel overview
EFX500 and EFX600 control panel settings
Personality feature Setting*
0
DMX mode
2
1
1
2
Pan (mirror drum
swivel) invert
Tilt (mirror drum
rotation) invert
0
1
0
1
1
3
Music trig
sensitivity**
↓
9
Mode 1 (normal)
Mode 2 (extended)
Pan normal
Pan inverted
Tilt normal
Tilt inverted
Minimum
Maximum
EFX700 control panel settings
Personality feature Setting*
0
DMX mode
2
1
1
3
Music trig
sensitivity**
↓
9
Mode 1 (normal)
Mode 2 (extended)
Minimum
Maximum
↓
↓
EFX800 control panel settings
Personality feature Setting*
0
2
3
* Default settings are shown in bold type.
** Music trig sensitivity is
36 Mania EFX user manual
DMX mode
Tilt (color paddlewheel rotation) invert
Music trig
sensitivity**
1
2
0
1
1
↓
9
6 by default.
Mode 1 (normal)
Mode 2 (extended)
Tilt normal
Tilt inverted
Minimum
↓
Maximum
Page 37
Mania EFX500 DMX protocol
Channel Value Percent Function
Strobe effect, auto trig, music trig, reset
1
2
0 - 4
5 - 68
69 - 100
101 - 132
133 - 249
250 - 255
0 - 255 0 - 100
0 - 9
10 - 19
20 - 29
30 - 39
40 - 49
50 - 59
60 - 69
0 - 1
2 - 26
27 - 39
40 - 51
52 - 97
98 - 100
0 - 3
4 - 7
8 - 11
12 - 15
16 - 19
20 - 23
24 - 26
No function
Strobe (fast to slow)
Remote stand-alone, auto trig
Remote stand-alone, music trig
Reserved, no function
Reset fixture (value must be held for 5 seconds)
Intensity
0 - 100%
Colored gobo wheel positions, gobo wheel rotation,
gobo wheel music trig
Full gobo positions
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
3
70 - 79
80 - 89
90 - 99
100 - 109
110 - 119
120 - 175
176 - 207
208 - 239
240 - 244
245 - 249
250 - 255
27 - 30
31 - 35
36 - 38
39 - 42
43 - 46
47 - 68
69 - 81
82 - 93
94 - 95
96 - 97
98 - 100
Mania EFX500 DMX protocol 37
Gobo 8
Gobo 9
Gobo 10
Gobo 11
Gobo 12 (Blackout)
Reserved (Blackout, gobo 12)
Continuous Rotation
Clockwise (fast
Counterclockwise (slow
Music function
Gobo wheel music trig fast
Gobo wheel music trig slow
Gobo wheel music trig dynamic
→ slow)
→ fast)
Page 38
Channel Value Percent Function
Colored gobo wheel shake
4
5
0 - 1
2 - 128
129 - 255
0 - 1
2 - 65
66 - 129
130 - 192
193 - 208
209 - 239
240 - 244
245 - 249
250 - 255
0
63
0
1 - 50
51 - 100
0
1 - 25
26 - 50
51 - 75
76 - 81
82 - 93
94 - 95
96 - 97
98 - 100
0
24
No function
Narrow shake (slow
Wide shake (slow
Mirror dish rotation, shake and music trig
Stop
Counterclockwise rotation (fast
Clockwise rotation (slow
Shake (slow
Random shake
Reserved, stop
Mirror dish music trig, fast
Mirror dish music trig, slow
Mirror dish music trig, dynamic
Pan (mirror drum swivel) position, shake and music
trig
Maximum left pan
Neutral
→ fast)
→ fast)
→ fast)
→ slow)
→ fast)
6
7
127
128 - 182
183 - 239
240 - 244
245 - 249
250 - 255
0 - 1
2 - 63
64 - 65
66 - 127
128 - 129
130 - 184
185 - 239
240 - 244
245 - 249
250 - 255
50
51 - 71
72 - 93
94 - 95
96 - 97
98 - 100
0
1 - 24
25
26 - 49
50
51 - 72
73 - 93
94 - 95
96 - 97
98 - 100
Maximum right pan
Narrow shake (slow
Wide shake (slow
Music trig pan, fast
Music trig pan, slow
Music trig pan, dynamic
Tilt (mirror drum rotation) rotation, shake and music
trig
No rotation
Clockwise rotation (slow
No rotation
Counterclockwise rotation (fast
No rotation
Narrow shake (slow
Wide shake (slow
Mirror drum rotation music trig, fast
Mirror drum rotation music trig, slow
Mirror drum rotation music trig, dynamic
→ fast)
→ fast)
→ fast)
→ slow)
→ fast)
→ fast)
38 Mania EFX user manual
Page 39
Channel Value Percent Function
Macros (DMX mode 2 only)
8*
9*
0 - 15
16 - 31
32 - 47
48 - 63
64 - 79
80 - 95
96 - 111
112 - 127
128 - 143
144 - 159
160 - 175
176 - 191
192 - 207
208 - 255
0 - 1
2 - 255
0 - 5
6 - 11
12 - 18
19 - 24
25 - 30
31 - 37
38 - 43
44 - 49
50 - 55
56 - 62
63 - 68
69 - 74
75 - 81
82 - 100
0
1 - 100
No Macro
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8
Macro 9
Macro 10
Macro 11
Macro 12
Reserved. No function
Effects speed (DMX mode 2 only)
Tracking (default)
→ slow
Fast
* Channels 8 and 9 are available in DMX mode 2 only. In DMX mode 1, effects speed is
set to ‘tracking’.
Mania EFX500 DMX protocol 39
Page 40
Mania EFX600 DMX protocol
Channel Value Percent Function
Intensity, strobe effect, auto trig, reset, lamp off
1
0 - 4
5 - 122
123 - 129
130 - 189
190 - 199
200 - 209
210 - 219
220 - 239
240 - 249
250 - 255
0 - 9
10 - 19
20 - 29
30 - 39
0 - 1
2 - 47
48 - 50
51 - 74
75 - 78
79 - 82
83 - 86
87 - 94
95 - 98
99 - 100
0 - 3
4 - 7
8 - 11
12 - 15
Blackout (shutter closed)
Intensity 0-100%, lamp on
Shutter open
Strobe (fast to slow)
Shutter closed
Random strobe
Remote stand-alone, auto trig
Blackout (shutter closed)
Reset fixture (value must be held for 5 seconds)
Lamp off (value must be held for 5 seconds and channels
2 & 3 must be set to more than 252 / 99%). Note that
there is an 8-minute delay before lamp can be restruck.
Colored gobo wheel position, rotation and music trig
Full gobo positions
Gobo 1
Gobo 2
Gobo 3
Gobo 4
40 - 49
50 - 59
60 - 69
70 - 79
80 - 89
2
40 Mania EFX user manual
90 - 99
100 - 109
110 - 119
120 - 175
176 - 207
208 - 239
240 - 244
245 - 249
250 - 255
16 - 19
20 - 23
24 - 26
27 - 30
31 - 35
36 - 38
39 - 42
43 - 46
47 - 68
69 - 81
82 - 93
94 - 95
96 - 97
98 - 100
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Gobo 9
Gobo 10
Gobo 11
Gobo 12
Reserved (gobo 12)
Continuous Rotation
Clockwise (fast
Counterclockwise (slow
Music function
Gobo wheel music trig fast
Gobo wheel music trig slow
Gobo wheel music trig dynamic
→ slow)
→ fast)
Page 41
Channel Value Percent Function
Colored gobo wheel shake
3
4
0 - 1
2 - 128
129 - 255
0 - 1
2 - 65
66 - 129
130 - 192
193 - 208
209 - 239
240 - 244
245 - 249
250 - 255
0
63
0
1 - 50
51 - 100
0
1 - 25
26 - 50
51 - 75
76 - 81
82 - 93
94 - 95
96 - 97
98 - 100
0
24
No function
Narrow shake (slow
Wide shake (slow
Mirror dish rotation, shake and music trig
Stop
Counterclockwise rotation (fast
Clockwise rotation (slow
Shake (various shakes)
Random shake
Reserved, stop
Mirror dish music trig, fast
Mirror dish music trig, slow
Mirror dish music trig, dynamic
Pan (mirror drum swivel) position, shake and music
trig
Maximum left pan
Neutral
→ fast)
→ fast)
→ slow)
→ fast)
5
6
127
128 - 182
183 - 239
240 - 244
245 - 249
250 - 255
0 - 1
2 - 63
64 - 65
66 - 127
128 - 129
130 - 184
185 - 239
240 - 244
245 - 249
250 - 255
50
51 - 71
72 - 93
94 - 95
96 - 97
98 - 100
0
1 - 24
25
26 - 49
50
51 - 72
73 - 93
94 - 95
96 - 97
98 - 100
Maximum right pan
Narrow shake (slow
Wide shake (slow
Music trig pan, fast
Music trig pan, slow
Music trig pan, dynamic
Tilt (mirror drum rotation) rotation, shake and music
trig
No rotation
Clockwise rotation (slow
No rotation
Counterclockwise rotation (fast
No rotation
Narrow shake (slow
Wide shake (slow
Mirror drum rotation music trig, fast
Mirror drum rotation music trig, slow
Mirror drum rotation music trig, dynamic
→ fast)
→ fast)
→ fast)
→ slow)
→ fast)
→ fast)
Mania EFX600 DMX protocol 41
Page 42
Channel Value Percent Function
Macros (DMX mode 2 only)
7*
8*
0 - 15
16 - 31
32 - 47
48 - 63
64 - 79
80 - 95
96 - 111
112 - 127
128 - 143
144 - 159
160 - 175
176 - 191
192 - 207
208 - 255
0 - 1
2 - 255
0 - 5
6 - 11
12 - 18
19 - 24
25 - 30
31 - 37
38 - 43
44 - 49
50 - 55
56 - 62
63 - 68
69 - 74
75 - 81
82 - 100
0
1 - 100
No Macro
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8
Macro 9
Macro 10
Macro 11
Macro 12
Reserved. No function
Effects speed (DMX mode 2 only)
Tracking (default)
→ slow
Fast
* Channels 7 and 8 are available in DMX mode 2 only. In DMX mode 1, effects speed is
set to ‘tracking’.
42 Mania EFX user manual
Page 43
Mania EFX700 DMX protocol
Channel Value Percent Function
Intensity, strobe effect, auto trig, reset, lamp off
1
0 - 4
5 - 122
123 - 129
130 - 189
190 - 199
200 - 209
210 - 219
220 - 239
240 - 249
250 - 255
0 - 9
10 - 19
20 - 29
30 - 39
0 - 1
2 - 47
48 - 50
51 - 74
75 - 78
79 - 82
83 - 86
87 - 94
95 - 98
99 - 100
0 - 3
4 - 7
8 - 11
12 - 15
Blackout (shutter closed)
Intensity 0-100%, lamp on
Shutter open
Strobe (fast to slow)
Shutter closed
Random strobe
Remote stand-alone, auto trig
Blackout (shutter closed)
Reset fixture (value must be held for 5 seconds)
Lamp off (value must be held for 5 seconds and channels
2 & 3 must be set to more than 252 / 99%). Note that
there is an 8-minute delay before lamp can be restruck.
Colored gobo wheel position, rotation and music trig
Full gobo positions
Gobo 1
Gobo 2
Gobo 3
Gobo 4
2
40 - 49
50 - 59
60 - 69
70 - 79
80 - 89
90 - 99
100 - 109
110 - 119
120 - 175
176 - 207
208 - 239
240 - 244
245 - 249
250 - 255
16 - 19
20 - 23
24 - 26
27 - 30
31 - 35
36 - 38
39 - 42
43 - 46
47 - 68
69 - 81
82 - 93
94 - 95
96 - 97
98 - 100
Mania EFX700 DMX protocol 43
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Gobo 9
Gobo 10
Gobo 11
Gobo 12
Reserved (gobo 12)
Continuous Rotation
Clockwise (fast
Counterclockwise (slow
Music function
Gobo wheel music trig fast
Gobo wheel music trig slow
Gobo wheel music trig dynamic
→ slow)
→ fast)
Page 44
Channel Value Percent Function
Colored gobo wheel shake
3
4
0 - 1
2 - 128
129 - 255
0 - 1
2 - 65
66 - 129
130 - 192
193 - 208
209 - 239
240 - 244
245 - 249
250 - 255
0 - 15
16 - 31
0
1 - 50
51 - 100
0
1 - 25
26 - 50
51 - 75
76 - 81
82 - 93
94 - 95
96 - 97
98 - 100
0 - 5
6 - 11
No function
Narrow shake (slow
Wide shake (slow
Mirror dish rotation, shake and music trig
Stop
Counterclockwise rotation (fast
Clockwise rotation (slow
Shake (various shakes)
Random shake
Reserved, stop
Mirror dish music trig, fast
Mirror dish music trig, slow
Mirror dish music trig, dynamic
Macros (DMX mode 2 only)
No Macro
Macro 1
→ fast)
→ fast)
→ slow)
→ fast)
5*
6*
32 - 47
48 - 63
64 - 79
80 - 95
96 - 111
112 - 127
128 - 143
144 - 159
160 - 175
176 - 191
192 - 207
208 - 255
0 - 1
2 - 255
12 - 18
19 - 24
25 - 30
31 - 37
38 - 43
44 - 49
50 - 55
56 - 62
63 - 68
69 - 74
75 - 81
82 - 100
0
1 - 100
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8
Macro 9
Macro 10
Macro 11
Macro 12
Reserved. No function
Effects speed (DMX mode 2 only)
Tracking (default)
→ slow
Fast
* Channels 5 and 6 are available in DMX mode 2 only. In DMX mode 1, effects speed is
set to ‘tracking’.
44 Mania EFX user manual
Page 45
Mania EFX800 DMX protocol
Channel Value Percent Function
Intensity, strobe effect, auto trig, reset, lamp off
1
0 - 4
5 - 122
123 - 129
130 - 189
190 - 199
200 - 209
210 - 219
220 - 239
240 - 249
250 - 255
0 - 9
10 - 19
20 - 29
30 - 39
0 - 1
2 - 47
48 - 50
51 - 74
75 - 78
79 - 82
83 - 86
87 - 94
95 - 98
99 - 100
0 - 3
4 - 7
8 - 11
12 - 15
Blackout (shutter closed)
Intensity 0-100%, lamp on
Shutter open
Strobe (fast to slow)
Shutter closed
Random strobe
Remote stand-alone, auto trig
Blackout (shutter closed)
Reset fixture (value must be held for 5 seconds)
Lamp off (value must be held for 5 seconds and channels
2 & 3 must be set to more than 252 / 99%). Note that
there is an 8-minute delay before lamp can be restruck.
Gobo wheel position, rotation and music trig
Full gobo positions
Gobo 1
Gobo 2
Gobo 3
Gobo 4
2
40 - 49
50 - 59
60 - 69
70 - 79
80 - 89
90 - 99
100 - 109
110 - 119
120 - 175
176 - 207
208 - 239
240 - 244
245 - 249
250 - 255
16 - 19
20 - 23
24 - 26
27 - 30
31 - 35
36 - 38
39 - 42
43 - 46
47 - 68
69 - 81
82 - 93
94 - 95
96 - 97
98 - 100
Mania EFX800 DMX protocol 45
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Gobo 9
Gobo 10
Gobo 11
Gobo 12
Reserved (gobo 12)
Continuous Rotation
Clockwise (fast
Counterclockwise (slow
Music function
Gobo wheel music trig fast
Gobo wheel music trig slow
Gobo wheel music trig dynamic
→ slow)
→ fast)
Page 46
Channel Value Percent Function
Gobo wheel shake
3
4
0 - 1
2 - 128
129 - 255
0 - 1
2 - 65
66 - 129
130 - 192
193 - 208
209 - 239
240 - 244
245 - 249
250 - 255
0 - 3
4 - 103
0
1 - 50
51 - 100
0
1 - 25
26 - 50
51 - 75
76 - 81
82 - 93
94 - 95
96 - 97
98 - 100
0-1
2 - 40
No function
Narrow shake (slow
Wide shake (slow
Mirror dish rotation, shake and music trig
Stop
Counterclockwise rotation (fast
Clockwise rotation (slow
Shake (various shakes)
Random shake
Reserved, stop
Mirror dish music trig, fast
Mirror dish music trig, slow
Mirror dish music trig, dynamic
Color paddlewheel position, rotation, shake and
music trig
No rotation
Fixed positions 0-360°
→ fast)
→ fast)
→ slow)
→ fast)
5
104 - 105
106 - 155
156 - 157
158 - 207
208 - 209
210 - 224
225 - 239
240 - 244
245 - 249
250 - 255
40-41
42 - 59
60-61
62 - 80
81 - 82
83 - 87
88 - 93
94 - 95
96 - 97
98 - 100
No rotation
Clockwise rotation (slow
No rotation
Counterclockwise rotation (fast
No rotation
Narrow shake (slow
Wide shake (slow
Music trig pan, fast
Music trig pan, slow
Music trig pan, dynamic
→ fast)
→ fast)
→ fast)
→ slow)
46 Mania EFX user manual
Page 47
Channel Value Percent Function
Macros (DMX mode 2 only)
6*
7*
0 - 15
16 - 31
32 - 47
48 - 63
64 - 79
80 - 95
96 - 111
112 - 127
128 - 143
144 - 159
160 - 175
176 - 191
192 - 207
208 - 255
0 - 1
2 - 255
0 - 5
6 - 11
12 - 18
19 - 24
25 - 30
31 - 37
38 - 43
44 - 49
50 - 55
56 - 62
63 - 68
69 - 74
75 - 81
82 - 100
0
1 - 100
No Macro
Macro 1
Macro 2
Macro 3
Macro 4
Macro 5
Macro 6
Macro 7
Macro 8
Macro 9
Macro 10
Macro 11
Macro 12
Reserved. No function
Effects speed (DMX mode 2 only)
Tracking (default)
→ slow
Fast
* Channels 6 and 7 are available in DMX mode 2 only. In DMX mode 1, effects speed is
set to ‘tracking’.
Mania EFX800 DMX protocol 47
Page 48
Mania EFX Series
specifications
Physical
Dimensions EFX500 & EFX600 (LxWXH) 410 x 500 x 230mm (16.2 x 19.7 x 9.1 in.)
Dimensions EFX700 & EFX800 (LxWXH) 400 x 500 x 230mm (15.8 x 19.7 x 9.1 in.)
EFX500 weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.5 kg (27.6 lb.)
EFX600 EU model weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 kg (31 lb.)
EFX600 US model weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 kg (36.5 lb.)
EFX700 EU model weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.1 kg (31.1 lb.)
EFX700 US model weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.6 kg (36.6 lb.)
EFX800 EU model weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.7 kg (32.4 lb.)
EFX800 US model weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17.2 kg (38 lb.)
All dimensions and weights include the supplied mounting plate
Installation
Orientation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .any
Minimum distance to combustible material . . . . . . . . . . . . . . . . . . . . . . . 0.1 m (4 in.)
Minimum distance to illuminated surface . . . . . . . . . . . . . . . . . . . . . . . 0.3 m (12 in.)
Minimum clearance around air vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.1 m (4in)
Suitable for mounting on combustible surfaces (wood, etc.) using
mounting bracket and plate and respecting minimum distances specified
Construction
Housing. . . . . . . . . . . . . . . . . . . . . . . .steel and aluminum, rubber corner protectors
Lamp
EFX500, all models
Lamp type . . . . . . . . . . . . . . . . . . . .24 V, 250 W halogen lamp with integral reflector
Lamp socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .GX5.3
EFX600, EFX700 & EFX800, all models
Lamp type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150 W discharge lamp
Lamp socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . G12
Control and programming
Control options . . . . . . . . . . . DMX, stand-alone music trig & auto trig, master/slave
Individual effects can be set to music trig remotely via DMX
EFX500: number of DMX channels. . . . . . . . . . . . . . . . . . .7 (mode 1) or 9 (mode 2)
EFX600: number of DMX channels. . . . . . . . . . . . . . . . . . .6 (mode 1) or 8 (mode 2)
EFX700: number of DMX channels. . . . . . . . . . . . . . . . . . .4 (mode 1) or 6 (mode 2)
EFX800: number of DMX channels. . . . . . . . . . . . . . . . . . .5 (mode 1) or 7 (mode 2)
Data protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .USITT DMX-512 (1990)
Page 49
Dynamic effects
EFX500, all models
Motorized rotating parabolic mirror dish
Motorized rotating gobo wheel, 11 colored gobos plus blackout
Motorized mirror drum, 180° swivel (pan) & 360° rotation (tilt)
0-100% dimmer
Strobe effect shutter
EFX600, all models
Motorized rotating parabolic mirror dish
Motorized rotating gobo wheel, 12 colored gobos
Motorized mirror drum, 180° swivel (pan) & 360° rotation (tilt)
Electromechanical 0-100% dimmer
Strobe effect shutter
EFX700, all models
Motorized rotating parabolic mirror dish
Motorized rotating gobo wheel, 12 colored gobos
Electromechanical 0-100% dimmer
Strobe effect shutter
EFX800, all models
Motorized rotating parabolic mirror dish
Motorized rotating gobo wheel, 12 gobos
Motorized color paddlewheel, 360° rotation (tilt)
Electromechanical 0-100% dimmer
Strobe effect shutter
Electrical
EFX500, all models
AC power . . switch-selectable, 110-120 VAC, 60 Hz / 220-240 VAC, 50 Hz nominal
Main fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.15 AT
Typical power and current*
@ 110 V, 60 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . 229 W, 2.1 A, PF = 0.997
@ 115 V, 60 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . 248 W, 2.2 A, PF = 0.997
@ 120 V, 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . 264 W, 2.2 A, PF = 0.997
@ 220 V, 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . 229 W, 1.1 A, PF = 0.995
@ 230 V, 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . 247 W, 1.1 A, PF = 0.995
@ 240 V, 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . 265 W, 1.2 A, PF = 0.994
EFX600, EFX700 & EFX800, EU models
AC power . . . . . . . . . . . . . . . . switch-selectable, 220-230/240 VAC, 50 Hz nominal
Main fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AT
Typical power and current*
@ 220 V, 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . 181 W, 0.9 A, PF = 0.950
@ 230 V, 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . 197 W, 1.0 A, PF = 0.926
@ 240 V, 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . 204 W, 1.0 A, PF = 0.923
Page 50
EFX600, EFX700 & EFX800, US models
AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110-120 VAC, 60 Hz nominal
Main fuse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.15 AT
Typical power and current*
@ 110 V, 60 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . 189 W, 1.8 A, PF = 0.963
@ 115 V, 60 Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . 207 W, 1.9 A, PF = 0.964
@ 120 V, 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . 226 W, 2.0 A, PF = 0.957
* V = volts, Hz = hertz, W = watts, A = amps, PF = power factor
Allow for a deviation of +/- 10% from typical figures listed above.
Measurements made at nominal voltage. Local supply voltages can vary by +/-10%.
Connections
Power input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-prong IEC male socket
Data in/out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-pin locking XLR)
Thermal
Time required to cool before handling. . . . . . . . . . . . . . . . . . . . minimum 10 minutes
Maximum ambient temperature (T
EFX500, all models
Maximum surface temperature, steady state, T
) . . . . . . . . . . . . . . . . . . . . . .40° C (104° F)
a
= 40° C . . . . . . . . . . 100°C (212° F)
a
EFX600, EFX700 & EFX800, all models
Maximum surface temperature, steady state, T
= 40° C . . . . . . . . . . . 80°C (176° F)
a
Approvals
EU EMC . . . . . . . . . . . . . . . . . EN 55015, EN 61547, EN 61000-3-3, EN 61000-3-2
EU safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN 60598-1, EN 60598-2-17
US safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UL 1573
Canadian safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..CSA C22.2 NO 166
Included items
EFX500, all models
Long-life 250 W halogen lamp
3 m (9.8 ft) EU mains cable 3x1.0mm
3 m (9.8 ft) EU mains cable 3x1.0mm
2 m (6.5 ft) US mains cable 18AWG with US male connector (UL approved)
5 meter (16.4 ft.) RS-485 XLR cable for data link . . . . . . . . . . . . . . . . P/N 11820008
User manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 35000168
2
with Schuko male connector
2
with no male connector
EFX600, EFX700 & EFX800, EU models
Long-life 150 W discharge lamp
3 m (9.8 ft) EU mains cable 3x1.0mm
3 m (9.8 ft) EU mains cable 3x1.0mm
5 meter (16.4 ft.) RS-485 XLR cable for data link . . . . . . . . . . . . . . . . P/N 11820008
User manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 35000168
2
with Schuko male connector
2
with no male connector
Page 51
EFX600, EFX700 & EFX800, US models
Long-life 150 W discharge lamp
2 m (6.5 ft) US mains cable 18AWG with US male connector (UL approved)
5 meter (16.4 ft.) RS-485 XLR cable for data link . . . . . . . . . . . . . . . . P/N 11820008
User manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 35000168
Accessories
DMX termination plug (end of link), XLR male . . . . . . . . . . . . . . . . . . P/N 91613017
DMX termination plug, (start of link, master/slave), XLR female. . . . . P/N 91613018
G-clamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91602003
Half-coupler clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91602005
5-pin male to 3-pin female XLR adaptor cable . . . . . . . . . . . . . . . . . . P/N 11820005
5 meter (16.4 ft.) RS-485 XLR cable for data link . . . . . . . . . . . . . . . . P/N 11820008
EFX500, all models
Philips ELC 10H 250 W halogen lamp . . . . . . . . . . . . . . . . . . . . . . . . P/N 97000109
Main fuse, 3.15 AT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 05020043
EFX600, EFX700 & EFX 800, EU models
Philips CDM SA-T 150 W discharge lamp. . . . . . . . . . . . . . . . . . . . . . P/N 97010111
Osram HSD 150/70 150 W discharge lamp . . . . . . . . . . . . . . . . . . . . P/N 97010117
Main fuse, 2 AT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 05020009
EFX600, EFX700 & EFX 800, US models
Philips CDM SA-T 150 W discharge lamp. . . . . . . . . . . . . . . . . . . . . . P/N 97010111
Osram HSD 150/70 150 W discharge lamp . . . . . . . . . . . . . . . . . . . . P/N 97010117
Main fuse, 3.15 AT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 05020043
Ordering information
Mania EFX500, 115/230 V, 50/60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . P/N 90430050
Mania EFX600 EU model, 220-240 V, 50 Hz . . . . . . . . . . . . . . . . . . . P/N 90430052
Mania EFX600 US model, 110-120 V, 60 Hz . . . . . . . . . . . . . . . . . . . P/N 90430053
Mania EFX700 EU model, 220-240 V, 50 Hz . . . . . . . . . . . . . . . . . . . P/N 90430054
Mania EFX700 US model, 110-120 V, 60 Hz . . . . . . . . . . . . . . . . . . . P/N 90430055
Mania EFX800 EU model, 220-240 V, 50 Hz . . . . . . . . . . . . . . . . . . . P/N 90430056
Mania EFX800 US model, 110-120 V, 60 Hz . . . . . . . . . . . . . . . . . . . P/N 90430057
Page 52
Page 53
Page 54
Page 55
A
A A
50
50
40
40
Ø13.5
Ø9
Ø18
Page 56
www.martin.com • Olof Palmes Allé 18 • 8200 Aarhus N • Denmark
Tel: +45 8740 0000 •
Fax +45 8740 0010
Loading...