Martin Cyclo 03 Directional User Manual

martinarchitectural

Cyclo 03 Directional

user manual

Dimensions

Measurements are in millimeters

1135

218

285

107

1100

1200

250°

50°

50°

0°

50°

50°

0°

All rights reserved. No part of this manual may be reproduced, in any form or by any means, with-

out permission in writing from Martin Professional A/S, Denmark.

© 2004 Martin Professional A/S, Denmark.

Printed in Denmark.

P/N 35000163, Rev B

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Data linking multiple luminaires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Burning in fluorescent tubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Stand-alone operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Stand-alone operation settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Single stand-alone operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Master/slave stand-alone operation . . . . . . . . . . . . . . . . . . . . . . . . . 16

DMX controlled operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Connecting a DMX control device. . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Setting a luminaire to DMX operation . . . . . . . . . . . . . . . . . . . . . . . . 21

Controlling via DMX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Fluorescent tube replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

DMX protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Cyclo 03 Directional Specifications . . . . . . . . . . . . . . . . . . . 31

Introduction

Thank you for selecting the Martin Cyclo 03 Directional. The Cyclo 03
Directional is a dynamic fluorescent color changing luminaire that can be
programmed for stand-alone operation or controlled via DMX.

The Cyclo 03 Directional is designed for dynamic color illumination of walls
and surfaces. A patented optical system ensures effective color mixing
within the main reflector, allowing the luminaire to be positioned close to the
illuminated surface without color hot-spots. Dimmable T5 fluorescent tubes
combine high efficiency, bright color and long lamp life.

The Cyclo 03 Directional can be surface-mounted or mounted on standard
3-phase lighting track. It can be tilted through 250°, allowing flexibility of
installation.

Control cables are through-wired for easy installation.

The Cyclo 03 Directional features:

• Controllable RGB color-mixing

• Full 0-100% intensity control of the red, green and blue tubes

• High output, long life T5 fluorescent tubes

• Flexible mounting options

• 250° of tilt

Important! Read this manual before attempting to install this product.

The most recent version of this user manual is available from the Support
area of the Martin Architectural website at http://www.martin­architectural.com

Safety information

Warning! This product is for professional use only. It is not for household

use.

These products present risks of lethal or severe injury due to fire and heat,
electric shock and falls. Read this manual before powering or installing
these luminaires, follow the safety precautions listed below and observe all
warnings in this manual and on the luminaires. If you have questions about

Introduction 5

how to operate these luminaires safely, please contact your Martin dealer or
call the Martin 24-hour service hotline at [phone].

Protection from electric shock

• Disconnect the luminaire from AC power before removing or installing a
tube or any part, and when not in use.

• Always ground (earth) the luminaire electrically.

• Use only a source of AC power that complies with local building and
electrical codes and has both overload and ground (earth) fault protection.

• Ensure that the luminaire’s live and neutral conductors are both
connected to the same RCD (ground fault circuit-breaker)

• Do not expose the luminaires to rain or moisture.

• Refer all service to a Martin service technician.

Protection from burns and fire

• Provide a minimum clearance of 0.1 meters (4 inches) around the
luminaire.

• Do not modify the luminaire or install other than genuine Martin parts.

• Do not operate the luminaire if the ambient temperature (Ta) exceeds 40°
C (104° F).

Protection from injury due to falls

• Ensure that all components and installation fittings are securely fastened.

• Ensure that all supporting structures, surfaces and fasteners can bear the
weight of all luminaires installed.

• Block access below the work area whenever installing, servicing or
removing the luminaire.

6 Cyclo 03 Directional user manual

Installation

This section describes in general terms how to install the luminaire, connect
it to AC power and connect control data cables. These procedures must be
performed by qualified professionals.

Mounting

The Cyclo 03 Directional features two mounting options:

• track-mounting on standard 3-phase lighting track

• surface-mounting using mounting brackets that are available as
accessories.

Warning! Check that all fasteners, structures and surfaces used to mount

the Cyclo 03 Directional can bear the total weight of all devices
installed.

Work from a stable platform and block access below the work
area when installing or servicing luminaires above head-height.

Lighting track mounting

The Cyclo 03 Directional can be mounted on lighting track from all major
manufacturers (Nokia, Erco, Zumtobel, iGuzzini, Nordic Aluminium, etc.)

3mm

Installation 7

A 3mm Allen key is required for this operation.

To mount a Cyclo 03 Directional on lighting track:

1. Isolate the lighting track from the power supply and ensure that power
cannot be reapplied, even accidentally.

2. Hold the luminaire up to the lighting track and slide the ends of the
mounting arms into the slot in the track.

3. Supporting the luminaire in position, fully tighten the 3mm Allen screws in
the side of each mounting arm.

4. Check that the luminaire is held firmly in place before reapplying power.

Lighting track dimensions
can vary slightly between
manufacturers. If the Cyclo
03 Directional is not held
firmly in place, you may need
to repeat the above
procedure, adding the square
spacers supplied with the
luminaire to take up any
clearance between the
mounting arms and the
lighting track.

8 Cyclo 03 Directional user manual

Surface mounting

The Cyclo 03 Directional can be
surface-mounted on a floor, wall or
ceiling using a bracket kit that is
available as an accessory.

To surface-mount the Cyclo 03
Directional:

1. Ensure that the surface on which
you want to mount the Cyclo 03
Directional can support the
weight of all the luminaires
installed on it.

2. Mark up two points 1100mm
(43.3 in.) apart as center points
for the mounting brackets. Allow
enough space around the center
points for the 110mm (4.3 in.)
square cover plates

1100

Ø5.5

80

80

3. Hold each mounting bracket against the mounting surface so that the
raised ridge in the bracket runs at 90° to the long side of the Cyclo 03
Directional (see illustrations), and so that the center point you have
marked is visible in the middle of the rectangular hole in the center of the
bracket.

4. Mark the mounting surface using the holes at the corners of each bracket
as guides, and drill holes in the mounting surface for the fasteners.

5. Fasten the mounting brackets to the surface using eight high-tensile
(grade 8.8 or over) M5 fasteners (screws, masonry bolts, etc.). Note that
the ridge in the bracket must be at 90° to the long side of the luminaire.

110

COVERBRACKET

110

Installation 9

6. Clip the bracket covers over the brackets with the long side of the
rectangular hole at 90% to the.Cyclo 03 Directional.

7. Hold the luminaire up to the mounting brackets. Slide the ends of the
mounting arms through the rectangular holes in the bracket covers and
into the mounting brackets.

8. Carefully supporting the luminaire, fully tighten the 3mm Allen screws in
the side of each mounting arm.

9. Check that the luminaire is totally secure.

AC power

It is the installer’s responsibility to ensure that all local safety regulations
and legal requirements are observed when installing and connecting the
Cyclo 03 Directional.

AC mains power compatibility and consumption data are given in the
Specifications section on page 31.

Warning! Many installations use common neutral conductors in branch

circuit distribution boxes. The neutral lead in the cable must be
connected to the same RCD (ground fault circuit breaker) as the
live lead in the cable. If it is not, users are left unprotected from
the risk of potentially lethal electric shock. It is the installer’s
responsibility to ensure that the Cyclo 03 Directional’s neutral
conductor is connected to the same RCD as the live conductor.

Important! Cyclo 03 Directional luminaires incorporate four electronic

ballasts that “leak” a total current of between 0.8mA and 4mA to
ground (earth). Luminaires must be correctly connected to
ground so that this “leakage” current can be absorbed.

It is also important that installation is carried out correctly in
order to avoid unintentional tripping of the RCD (ground fault
circuit breaker). Because of the “leakage” current, we
recommend connecting a maximum of seven Cyclo 03
Directional luminaires per phase when circuits are protected by
a 30mA RCD. Bear in mind that some RCDs rated at 30mA may
trip when current leakage to ground is as low as 20mA.

Connecting to mains power

Cyclo 03 Directional luminaires have an ENSTO male connector built into
the casing for mains power input. A female ENSTO connector is supplied
with the luminaire for installation on the power supply cable.

10 Cyclo 03 Directional user manual

To draw power from lighting track, a suitable power take-off plug from the
lighting track supplier must be installed on the power supply cable in
accordance with the lighting track supplier’s instructions.

Some common color-coding systems for mains wiring is given below:

Wire (EU) Wire (US) Pin Marking

brown black live “L” or “1”

blue white neutral “N”

yellow/green green ground

When installing the female ENSTO connector on the power cable, note the
markings next to the screw terminals:

• The terminal marked 1 must be connected

to the live wire.

• The centre terminal marked must be
connected to the ground (earth) wire.

• The terminal marked

N must be connected

the neutral wire.

The following connectors and cables are available from your Martin dealer:

ENSTO 3-pole 16A/250V male connector . . . . . . . . . . . P/N 05347202

ENSTO 3-pole 16A/250V female connector . . . . . . . . . . P/N 05327202

ENSTO male/female cable (15 cm/5.9in.). . . . . . . . . . . . .P/N 11501019

Installation 11

Data linking multiple luminaires

You need to create a serial data link to:

• Operate two or more Cyclo 03 Directionals in master/slave stand-alone
mode, where all luminaires run a synchronized light show without a
separate DMX control device

• Control luminaires with a DMX control device.

A reliable data connection requires suitable cable. CAT 5 (category 5) UTP
(unshielded twisted pair) network cable is suitable for this purpose. Your
Martin Architectural dealer can advise and supply suitable cable.

Luminaires on a serial data link must be daisy-chained in one single line,
maximum 500 meters (1640 ft.) long, with maximum 32 luminaires. To
exceed 32 luminaires or 500 meters, or to add branches, an optically
isolated amplifier-splitter such as the Martin RS-485 Opto-Splitter (P/N

90758060) must be used.

Data cable can be connected to the Cyclo 03 Directional via RJ-45 sockets
that are wired as follows:

• pins 7 & 8 to ground (earth)

• pin 2 to signal - (cold)

• pin 1 to signal + (hot).

DMX controller

Termination plug

Master

Slave

Slave

Termination plug

DMX control link

12 Cyclo 03 Directional user manual

Master/slave link

To create the data link:

1. Use suitable cable to connect one of the RJ-45 sockets on the first Cyclo
03 Directional to an RJ-45 socket on the next luminaire.

2. Continue connecting up to 32 luminaires using the RJ-45 sockets.

3. Terminate the link by inserting a an RJ-45 DMX termination plug (P/N

91613028) in the RJ-45 data output of the last luminaire.

4. If using a DMX control device, use suitable cable to connect the device’s
DMX output to one of the RJ-45 sockets on the first Cyclo 03 Directional.

TIp! Random “flicker” and other unexplained control problems

during stand-alone master/slave operation can often be cured
by inserting an RJ-45 DMX termination plug into the unused
socket of the first luminaire.

Burning in fluorescent tubes

Optimum tube performance is obtained after burning in new fluorescent
tubes for 100 hours at full power.

Installation 13

Stand-alone operation

In stand-alone operation, the Cyclo 03 Directional can be used without a
DMX controller. Static single colors or two-color mixes can be displayed, or
luminaires can be programmed to change colors in cycles. Changes can be
programmed at 1, 5, 10 or 30 second intervals.

Two stand-alone operation modes are available:

•In single stand-alone operation, luminaires run independently of each
other. No data link is required.

•In master/slave stand-alone operation, luminaires must be linked.
Synchronized action in all luminaires is triggered by one “master”
luminaire.

In both single and master/slave stand-alone operation, luminaires are
programmed via the pins on the DIP switch on the luminaire’s housing as
shown in Table 1.

Pin Function

1 Red active
2 Green active
3 Blue active
4 Not used
5 & 6 Program speed

Pin 6 Pin 5 Speed

OFF OFF 1 sec. steps (fastest setting)
OFF ON 5 sec. steps
ON OFF 10 sec. steps

ON ON 30 sec. steps (slowest setting)
7 OFF = Blackout fading, ON = Crossfading
8 OFF = Run program, ON = Pause program
9 OFF = Master, ON = Slave (Note: do not set more than one luminaire as master)
10 ON = Stand-alone mode.

Table 1. Stand-alone DIP switch settings

14 Cyclo 03 Directional user manual

A quick reference table covering DIP switch functions is also provided on

Blue

100% Blue

0% Red

50% Blue

50% Red

0% Blue

100% Red

the back cover of this manual.

Stand-alone operation settings

Activating colors

DIP switch pins 1 to 3 each activate a color in the stand-alone program.

Setting program speed

Combinations of DIP switch pins 5 and 6 allow one of four different speeds
to be set.

Fading between colors

If DIP switch 7 is set to OFF (blackout fading), colors fade to almost
blackout before the next color fades in.

100%

50%

0%

If DIP switch 7 is set to ON (crossfading), color fading overlaps. If two or
more colors are active, one color fades in while another is fading out, giving
a color mixing effect. For example, if red and blue are activated and
crossfading is selected, colors will crossfade from red through purple to
blue, then back through purple to red in a continuous cycle (see example).

Red

Blue

100% Blue

0% Red

Blue

50% Red
50% Blue

Purple

100% Red

0% Blue

Time

Red

Example: crossfading between red and blue

Stand-alone operation 15

Setting a static color display

In stand-alone operation, a static (non-changing) color display can be set by
pausing the program at the point where it is showing the desired color.
Either one color or a mix of two colors can be “frozen” in this way.

To set a static color display:

1. Activate the color you wish to display (if you wish to display a two-color
mix, activate these two colors) on DIP switch pins 1 to 3.

2. Set the luminaire as master by setting DIP switch pin 9 to OFF.

3. Set DIP switch pins 5 and 6 to ON to activate the slowest program speed.

4. Set DIP switch pin 7 to OFF to activate crossfading and DIP switch pin 8
to OFF to activate the program.

5. When the desired color or color mix appears, pause the program by
moving DIP switch 8 to ON. This color will remain “frozen” until DIP
switch 8 is moved to OFF.

Note that the paused color is lost when the luminaire is powered off. When
powering the luminaire on again, DIP switch pin 8 must be moved to OFF
before the program will start.

Single stand-alone operation

In single stand-alone operation, a luminaire runs its own program
independently of all other luminaires. To do this, the luminaire must be set
as a master.

Activating single stand-alone operation

To activate single stand-alone operation:

1. Set DIP switch pin 10 to ON (activates stand-alone mode).

2. Set DIP switch pin 9 to OFF (activates master mode).

3. Apply power and program the luminaire using DIP switch pins 1 - 8 (see
"Table 1. Stand-alone DIP switch settings" on page 14).

Master/slave stand-alone operation

Important! Do not set more than one luminaire on a data link as master,

and do not set a luminaire as master on a data link with a DMX

16 Cyclo 03 Directional user manual

controller. Doing so may cause damage to the electronics that is
not covered by the product warranty.

In master/slave stand-alone operation, one master luminaire transmits a
synchronizing signal to slave luminaires over the data link each time it starts
a new action. Slave luminaires start their next programmed action when
they receive this signal from the master luminaire. Programs can be
identical on all luminaires, or luminaires can – subject to certain practical
constraints – run programs that are synchronized but not identical.

Note that:

• Colors are always displayed in the order: red, then green, then blue. This
means that if red is activated, it will always be first in the program. If red is
not activated but green is activated, green will be first in the program.

• Each luminaire follows the program set on its own DIP switch as
described in "Table 1. Stand-alone DIP switch settings" on page 14.

More sophisticated light shows can be programmed using a DMX controller
(see “DMX controlled operation” on page 21).

The synchronization signal used by the Cyclo 03 Directional is identical to
that used in other 3-tube Cyclo luminaires, allowing these products to be
combined in master/slave operation on one data link. However, it is not
compatible with 4-tube Cyclos. Consult your Martin Architectural dealer if
you need advice on combining and controlling products.

Identical light shows

Master and slave luminaires can be set to behave identically. In this mode,
the master sends synchronizing signals to the slaves, and all luminaires run
the same light show. Each slave luminaire follows the program set on its
own DIP switch, so for identical operation, all luminaires’ DIP switch settings
must be the same apart from pin 9, which is set to ON for slaves and OFF
for the master.

Synchronized non-identical light shows

It is also possible to synchronize changes but program slave luminaires to
behave differently from the master. To use this feature effectively, you need
to plan your light show using scenes as building blocks and set the
luminaires’ DIP switches accordingly.

A scene is a change from one ouput to another. When a luminaire is in slave
mode, it starts a scene when it receives a synchronization signal from the
master. The time taken by the scene is determined by the speed setting of
the DIP switch. A slave will not respond to new synchronization signals until
its scene is complete.

Stand-alone operation 17

When crossfading is selected, each color takes up one scene (fade in only).
When blackout fading is selected, each color takes up two scenes (fade in
and fade out). This means that a maximum of 6 scenes can be programmed
with all 3 colors activated and blackout fading selected.

Each time the master luminaire starts at scene 1, it sends a signal to all the
slave luminaires to start at scene 1. This means that if a slave luminaire has:

1. Fewer scenes than the master luminaire, it will run these in a cycle until
the master luminaire signals that the program should start from the
beginning again.

2. More scenes than the master, the additional scenes will never run,
because the program will reset to the first scene when the master starts
its program from the beginning.

Here is an example of what will happen when a slave luminaire has fewer
scenes than the master luminaire:

Luminaire setting Scene pattern

Master with 6 scenes 123456 123456 123456 ...
Slave with 4 scenes 123412 123412 123412...

Program examples

The following examples show how an individual luminaire’s program is
made up of scenes.

The following symbols are used in program diagrams:

Tube turned fully off

Fade in

Fade out
Fade to 50% and back to 100% in one scene

(applies when only one color is active and
crossfading is selected)

Example 1

DIP switch 7 is set to ON (crossfading) and only red is activated:

18 Cyclo 03 Directional user manual

Red

Scene

1 1 11 111 1 111 1

Example 2

DIP switch 7 is set to OFF (blackout fading) and only red is activated:

Red

Scene

21 21 21 21 21 21

Example 3

DIP switch 7 is set to ON (crossfading) and red and blue are activated:

Red

Blue

Scene

1 2 21 211 2 21 21

Example 4

DIP switch 7 is set to OFF (blackout fading) and red and blue are activated:

Red

Blue

Scene

21 43 421 3 421 3

Example 5

To achieve a rainbow effect, activate red, green and blue and set DIP switch
pin 7 to ON (crossfading).

Red

Green

Blue

Scene

1 2 3 1 2 3 1 2 3 1 2 3

Activating master/slave stand-alone operation

To activate master/slave stand-alone operation:

1. Power all luminaires off.

2. Set all luminaires as slaves and put them into stand-alone mode by
setting DIP switch pins 9 and 10 to ON.

3. Decide which luminaire to use as master and set this luminaire’s DIP
switch pin 9 to OFF. Note that any luminaire can be set as master, but

Stand-alone operation 19

you will obtain the most reliable data signal by either setting the first
luminaire on the link as master or using RJ-45 DMX termination plugs at
both ends of the data link.

4. When power is applied, slave luminaires will go to the next scene in their
program each time the master goes to its next scene. Slave luminaires
will also start scene 1 of their programs each time the master starts
scene 1 of its program.

20 Cyclo 03 Directional user manual

DMX controlled operation

The Cyclo 03 Directional may be programmed and operated with any
lighting control device that is compatible with the USITT DMX standard.

See also “DMX protocol” on page 30.

Connecting a DMX control device

Connect a data cable to the DMX control device’s data output and one of the
Cyclo 03 Directional’s RJ-45 DMX sockets. If your control device has an
XLR data output socket, you may need to buy or wire an XLR-to-RJ45
converter. For details of wiring and polarity, see “Data linking multiple
luminaires” on page 12.

Setting a luminaire to DMX
operation

DMX operation is enabled by setting pin 10 on the DIP switch to OFF. Pins
1 - 9 are then used to set the luminaire’s control address.

Setting a DMX control address

The Cyclo 03 Directional uses 3 DMX control channels. The DMX address,
also known as the start channel, is the first of these channels. It must be set
on the luminaire and selected on the DMX controller before the controller
can send commands to the luminaire via a DMX link.

The Cyclo 03 Directional responds to commands sent to the DMX address
and the next two channels. If the DMX address is set to 100, the Cyclo 03
Directional uses channels 100, 101 and102.

Allow enough channels when setting the DMX address. If control channels
for one luminaire overlap control channels for another luminaire, one of the
luminaires will receive the wrong commands.

If two or more Cyclo 03 Directionals share the same DMX address, they will
receive the same commands and respond identically. Individual control will
be impossible.

DMX controlled operation 21

The default factory-set control address is ‘1’.

To set the Cyclo 03 Directional’s DMX address:

1. Set DIP switch pin 10 to OFF.

2. Decide on a DMX address for the luminaire. If you are calculating the
DMX addresses for multiple fixtures, save time by using the online Martin
Address Calculator at
http://www.martin.dk/service/utilities/AddrCalc/index.asp (see illustration
below).

3. You can also look up DIP-switch settings using the Martin DIP Switch

Calculator, available for use and downloadable at
http://www.martin.dk/service/dipswitchpopup.htm
If you do not have Internet access, refer to "Table 2: DIP switch address
settings" on page 23.

4. Set DIP switch pins 1 through 9 to ON (1) or OFF (0) with reference to

the table.

22 Cyclo 03 Directional user manual

Find the address in the table. Read the settings for pins 1 - 5 to the left and
read the settings for pins 6 - 9 above the address. “0” means OFF and “1”
means ON. Pin 10 is always OFF for DMX operation.

For example, to set the DMX address to 101, you need to set DIP-switch
pins 1, 3, 6 and 7 to ON. The DIP switch settings for Channel 101 are
highlighted in the table.

DIP switch Setting

0 = OFF

1 = ON

#1 #2 #3 #4 #5

0 0 0 0 0 32 64 96 128 160 192 224 256 288 320 352 384 416 448 480
1 0 0 0 0 1 33 65 97 129 161 193 225 257 289 321 353 385 417 449 481
0 1 0 0 0 2 34 66 98 130 162 194 226 258 290 322 354 386 418 450 482
1 1 0 0 0 3 35 67 99 131 163 195 227 259 291 323 355 387 419 451 483
0 0 1 0 0 4 36 68 100 132 164 196 228 260 292 324 356 388 420 452 484
1 0 1 0 0 5 37 69 101 133 165 197 229 261 293 325 357 389 421 453 485
0 1 1 0 0 6 38 70 102 134 166 198 230 262 294 326 358 390 422 454 486
1 1 1 0 0 7 39 71 103 135 167 199 231 263 295 327 359 391 423 455 487
0 0 0 1 0 8 40 72 104 136 168 200 232 264 296 328 360 392 424 456 488
1 0 0 1 0 9 41 73 105 137 169 201 233 265 297 329 361 393 425 457 489
0 1 0 1 0 10 42 74 106 138 170 202 234 266 298 330 362 394 426 458 490
1 1 0 1 0 11 43 75 107 139 171 203 235 267 299 331 363 395 427 459 491
0 0 1 1 0 12 44 76 108 140 172 204 236 268 300 332 364 396 428 460 492
1 0 1 1 0 13 45 77 109 141 173 205 237 269 301 333 365 397 429 461 493
0 1 1 1 0 14 46 78 110 142 174 206 238 270 302 334 366 398 430 462 494
1 1 1 1 0 15 47 79 111 143 175 207 239 271 303 335 367 399 431 463 495
0 0 0 0 1 16 48 80 112 144 176 208 240 272 304 336 368 400 432 464 496
1 0 0 0 1 17 49 81 113 145 177 209 241 273 305 337 369 401 433 465 497
0 1 0 0 1 18 50 82 114 146 178 210 242 274 306 338 370 402 434 466 498
1 1 0 0 1 19 51 83 115 147 179 211 243 275 307 339 371 403 435 467 499
0 0 1 0 1 20 52 84 116 148 180 212 244 276 308 340 372 404 436 468 500
1 0 1 0 1 21 53 85 117 149 181 213 245 277 309 341 373 405 437 469 501
0 1 1 0 1 22 54 86 118 150 182 214 246 278 310 342 374 406 438 470 502
1 1 1 0 1 23 55 87 119 151 183 215 247 279 311 343 375 407 439 471 503
0 0 0 1 1 24 56 88 120 152 184 216 248 280 312 344 376 408 440 472 504
1 0 0 1 1 25 57 89 121 153 185 217 249 281 313 345 377 409 441 473 505
0 1 0 1 1 26 58 90 122 154 186 218 250 282 314 346 378 410 442 474 506
1 1 0 1 1 27 59 91 123 155 187 219 251 283 315 347 379 411 443 475 507
0 0 1 1 1 28 60 92 124 156 188 220 252 284 316 348 380 412 444 476 508
1 0 1 1 1 29 61 93 125 157 189 221 253 285 317 349 381 413 445 477 509
0 1 1 1 1 30 62 94 126 158 190 222 254 286 318 350 382 414 446 478 510
1 1 1 1 1 31 63 95 127 159 191 223 255 287 319 351 383 415 447 479 511

#90000 000011111111
#80000 111100001111
#70011 001100110011
#60101 010101010101

Table 2: DIP switch address settings

DMX controlled operation 23

Controlling via DMX

The Cyclo 03 Directional’s advanced fluorescent tubes can be dimmed
from maximum output right down to zero using three channels on a
DMX controller. This allows a wide range of color shades with almost
infinitely variable intensity to be obtained using additive color mixing.
The color temperature of white light can also be fine-tuned.

Depending on the functions available on the controller, sophisticated
light shows on the Cyclo 03 Directional can be programmed over time,
allowing constantly and rapidly shifting color mixes, or color displays
which change slowly according to the time of day, or even year, for
example. See the controller’s manual for details.

Your Martin Architectural dealer can advise about available controllers
and control options.

Service

With long-life fluorescent tubes and no moving parts, the Cyclo 03
Directional is almost service-free.

Fluorescent tube replacement

The Osram high output T5 tubes fitted as standard meet color specifications
for at least 10 000 hours, after which color intensity may gradually fall.
Average tube life is 20 000 hours, but note that tube life will vary depending
on operating conditions.

No tools are required to replace a fluorescent tube on the Cyclo 03
Directional.

The reflector and diffuser must be removed for access to the tubes. These
two components are attached to the luminaire housing by safety wires and
can be left hanging from these wires during tube replacement.

Diffuser

Reflector

Service 25

To change a tube:

1. Isolate the luminaire from
the power supply and
ensure that power cannot
be reapplied, even
accidentally.

2. Ensure that the luminaire is
securely mounted before
beginning any servicing
work.

3. The reflector is held in
place by metal spring clips.
Hold the second fin from
each end firmly and pull
downwards to release the
reflector. If the reflector is
difficult to move by pulling,
insert a small screwdriver
between the reflector and
the housing, next to the
second fin from the end, to
help release the clip.

26 Cyclo 03 Directional user manual

4. The diffuser is held in place
by metal clips at each end of
the luminaire. Push a clip
back and remove the
diffuser. You now have
access to the tubes.

5. Pressing on the metal caps
at both ends of the tube, rotate
the tube 1/4 turn in whichever
direction is easiest, and slide
the tube’s terminal pins out of
their sockets. Support the tube
at both ends as it is released.

6. To install a new tube, line it up so that the manufacturer’s markings on all
tubes are at the same end of the luminaire. Slide the tube’s terminal pins
fully into their sockets and rotate the tube 1/4 turn to engage the pins.
Check that the tube is held securely in the sockets.

7. Replace the diffuser and then the reflector by pushing them onto their
clips before reapplying power.

Service 27

Tube positions

Tube positions in the Cyclo 03 Directional are identified as follows:

Marking in
luminaire

R

G

B

The burning positions of fluorescent tubes affect their operating
temperature, light output and tube life. For best results:

• Install tubes so that the manufacturer’s markings are all at the same end
of the luminaire.

• If the luminaire is mounted in a vertical position or at an angle from the
horizontal, place the ends of the tubes that carry the manufacturer’s
markings at the lower end of the luminaire.

Marking on
tube Reference illustration

OSRAM FQ
54W/60 RED

OSRAM FQ
54W/66 GREEN

OSRAM FQ
54W/67 BLUE

R G B

Cleaning

Turn off power to the luminaire before cleaning, and use a damp cloth to
wipe clean.

28 Cyclo 03 Directional user manual

Troubleshooting

Problem Probable cause(s) Remedy

No response from fixture when
power is applied.

Fixture does not respond
correctly to DMX control.

In stand-alone mode, DIP
switch pin 8 set to ON (pause).

No power to luminaire. Check power connections.
No power to lighting track. Check power connection to

Ground fault protection circuit
breaker (RCD) has tripped.

Controller not connected. Check DMX data link. Inspect

Incorrect DMX addressing. Check address setting on

Data link not terminated. Insert RJ-45 termination plug

Two devices transmitting on
link.

Set DIP switch pin 8 to OFF to
resume stand-alone program.

lighting track.
Reset RCD. If problem

persists, have an electrician
replace the RCD or reduce the
number of fixtures powered
via one RCD.

connections and test cables.
Repair or replace as
necessary.

fixture and controller.

in unused socket of last fixture
on data link.

Check that all luminaires are
set as slaves (DIP s witch pin 9
ON).

Fixtures do not behave
correctly in master/slave mode

Poor quality light output and/or
color rendering.

Defective luminaire. Bypass luminaires one at a

time until normal operation is
regained.

Two luminaires transmitting on
link.

Defective luminaire. Bypass luminaires one at a

Tube or tubes not burnt in. Run luminaire for at least 100

Tube defective. Disconnect luminaire and

Check that only one luminaire
is set to operate as master.

time until normal operation is
regained.

hours to burn in tubes.

replace tube.

Troubleshooting 29

DMX protocol

Channel Value Percent Function

1

2

3

0-2

3-252

253-255

0-2

3-252

253-255

0-2

3-252

253-255

1 - 99

100

1 - 99

100

1 - 99

100

Start code = 0

Red intensity

0

0

0

Tube off
Intensity 1
Intensity 100%

Green intensity

Tube off
Intensity 1
Intensity 100%

Blue intensity

Tube off
Intensity 1
Intensity 100%

→100%

→100%

→100%

30 Cyclo 03 Directional user manual

Cyclo 03 Directional

PHYSICAL

L x W x H (with mounting arms) . . . . . . . . . . . . . .1200 x 107 x 285 mm

L x W x H (without mounting arms) . . . . . . . . . . . .1200 x 107 x 218 mm

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7 kg (19.3 lbs)

Luminaire colors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Titanium, white

SOURCE

Light source. . . . . . . . . . . . . . . . . . . . . . . T5 fluorescent tubes (3x54W)

Approved lamp type . . . . . . . . . . . . . . . . . OSRAM T5 high output 54W

Color authenticity . . . . . . . . . . . . . . . . . . . Guaranteed to 10 000 hours

Average tube life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 000 hours

DYNAMIC EFFECTS

0-100% dimmable tubes . . . . . . . . . . . . . . . . . . . . .Red, green and blue

Specifications

(47.3 x 4.2 x 11.2 in.)

(47.3 x 4.2 x 8.6 in.)

CONTROL AND PROGRAMMING

Control options . . . . . . . . . . . . . . . DMX512, stand-alone, master/slave

Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RS-485

Setting and addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DIP switch

Data input/ output . . . . . . . . . . . . . . . . . . . . . . . . RJ-45 (through-wired)

Number of DMX channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

INSTALLATION

3-phase lighting track mounting with universal track adaptor
Surface mounting with optional mounting brackets

Orientation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Any

Minimum free space around luminaire . . . . . . . . . . . . . . 25 mm (1 inch)

THERMAL

Maximum ambient temperature (T

Maximum total heat dissipation. . . . . . . . . . . . . . . . . . . . . . 618 BTU/hr.

Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Convection

POWER

AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 V - 254 V, 50 / 60 Hz

Maximum power and current @ 208 V / 50 Hz . . . . . . . . 0.87 A / 180 W

Maximum power and current @ 230 V / 50 Hz . . . . . . . . 0.80 A / 181 W

Maximum power and current @ 250 V / 50 Hz . . . . . . . . 0.73 A / 179 W

AC input . . . . . . . . . . . . . . . . . . . . . . . . . . EnstoNet Installation System

) . . . . . . . . . . . . . . . . 40° C (104° F)

a

Cyclo 03 Directional Specifications 31

CONSTRUCTION

Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mild steel

Optics . . . . . . . . . . . . . . . . . . . . . . . . . . High specular 99.9% aluminum

INCLUDED ITEMS

Red T5 high output fluorescent tube . . . . . . . . . . . OSRAM FQ 54W/60

Green T5 high output fluorescent tube . . . . . . . . . OSRAM FQ 54W/66

Blue T5 high output fluorescent tube. . . . . . . . . . . OSRAM FQ 54W/67

ENSTO 3 pole 16A/250V male connector . . . . . . . . . . . . P/N 05347202

ENSTO 3 pole 16A/250V female connector . . . . . . . . . . P/N 05327202

User manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 35000163

ACCESSORIES

Wall/ceiling bracket (set of 2), titanium . . . . . . . . . . . . . . .P/N 91611187

Wall/ceiling bracket (set of 2), white . . . . . . . . . . . . . . . . .P/N 91611186

Termination plug RJ-45 . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91613028

RJ-45 connector (15 cm/ 5.9 in.) . . . . . . . . . . . . . . . . . . P/N 11840088

ENSTO male/female cable (15 cm/5.9in.) . . . . . . . . . . . P/N 11501019

XLR male to RJ-45 converter . . . . . . . . . . . . . . . . . . . . . P/N 11840087

XLR female to RJ-45 connector . . . . . . . . . . . . . . . . . . . P/N 11840086

50 x CAT5 network cables - 2 m (6.5 ft) . . . . . . . . . . . . . P/N 91611044

30 x CAT5 network cables - 5 m (16.4 ft) . . . . . . . . . . . . P/N 91611045

15 x CAT5 network cables - 10 m (32.8 ft) . . . . . . . . . . . P/N 91611046

ORDERING INFORMATION

Cyclo 03 Directional, titanium . . . . . . . . . . . . . . . . . . . . . P/N 90550055

Cyclo 03 Directional, white . . . . . . . . . . . . . . . . . . . . . . . P/N 90550050

32 Cyclo 03 Directional user manual

3. Blue

8. ON = Pause
OFF = Play

9. ON = Slave or DMX
OFF = Master

2. Green

1. Red

4. Not used

5/6. Program speed

10. ON = Stand-alone
OFF = DMX

1 2 3 4 5 6 7 8 9 10

ON

7. ON = Crossfading
OFF = Blackout fading

Quick reference

Cyclo 03 Directional DIP switch settings

www.martin-architectural.com • Olof Palmes Allé 18 • 8200 Aarhus N • Denmark

Tel: [phone] •

Fax [phone]