Martel Electronics LC-110, LC-110H Specifications

Calibration Technology Starts Here

-NEW-

FEATURES

Precision Current Loop Calibrator with HART Communications/Diagnostics

The Standard of Loop Calibration just got better with additional

Knob). This combination dramatically reduces the time it takes to measure, or source

HART capability!

The LC-110H differs from the standard LC-110 in that it incorporates HART communications and supports a select set of the HART universal and common practice commands. This unique

feature allows the LC-110H to be used as both a loop calibrator and communication tool.

In the communicator mode the user will be able to read basic device information, perform diagnostic

tests, and trim the calibration on most HART enabled transmitters. In the past, this could only be done with a

dedicated communicator, high-end multifunction calibrator costing thousands of dollars, or a laptop computer

with HART modem. The LC-110H will allow many more technicians to service and support HART devices.

In addition to HART communications, we also gave the user the ability to get information out of the LC-110H.

Need to quickly document the parameters of all the HART transmitters in your plant? Just add the

BetaLOG HART software/cable to capture and upload to twenty configurations in either

LC-110 & LC-110H

The Martel LC-110 and LC-110H are mA (loop) calibrators designed to

take the loop calibrator class to the next level. The new LC-110 series features

a user friendly interface with dedicated buttons and a rotary encoder (Quick-Set

voltage or current and power up a loop. The rugged case is contoured to easily fit a

technician’s hand and the large back lit graphics LCD is best in class.

(.csv) or (.txt) format.

We did not stop there! How about the ability to data log or record data on a

particular transmitter for troubleshooting? The data log tool features

selectable capture interval from 1 to 60 seconds and a logging

capacity of 9800 records or 99 individual sessions. Each data

sample contains the LC110H measurement, all four process

variables, and the standard status conditions

General Features

Best in Class Accuracy at 0.01% Reading

Small Rugged design operates on (6) standard AAA batteries

Intuitive interface that features a Quick-Set Knob

24VDC loop power with mA Measure Mode (-25% to 125%)

Resolution of 1µA on mA ranges and 1mV on voltages ranges

Built in selectable 250Ω Resistor for HART communications

Simple two wire connection for all measurements

Auto Shutdown to conserve battery life (adjustable up to

30 minutes)

Variable step & ramp time in seconds

Adjustable span selection (0 to 20mA or 4 to 20mA)

Valve Test (simulate defined mA values with % keys)

For more information:

- Call us toll free at 800-821-0023 or 603-434-1433

Fax us at 603-434-1653

- Or go to website, www. Martelcalibrators.com and click on LC-110 & LC-110H.

LC-110 & LC-110H

Specifications

Model LC-110 & LC-110H Functions: mA source, mA simulate, mA read, mA read/loop power,

and volts read.

Ranges: mA (0 to 24mA) and Volts (0 to 30VDC) Resolution: 1uA on mA ranges and 1mV on voltage range Accuracy: 0.01% +/- 2LSD all ranges (@23° +/- 5°C) Operating Temp range: -10°C to 55°C Humidity range: 10 to 95% non-condensing Stability: 20ppm of F.S. /°C from -10°C to 18°C and 28°C to 55°C Display: 128 x 64 pixels, LCD Graphic w/backlight, .34” high digits Power: 6AAA alkaline, lithium, or NiMH batteries Battery Life: ≥ 40 hours continuous use (measure mode using alkaline) Loop Compliance Voltage: 24VDC @ 20mA Over-Voltage Protection: 240VAC Overload Current Protection: 28mA DC EMC: EN61326 Annex A (Portable Instruments) Dimensions (L x W x D): 6” x 3.6” x 1.3” (15 cm x 9 cm x 3 cm) Weight: 9.5 ounces (0.3 kg) Included Accessories: NIST traceable calibration certificate with data,

batteries, test leads, and manual

Additional Features (LC110H)

Built in HART modem for communication capability to

perform the following commands:

- Read Message, Descriptor, Cal Date, Short and Long Tag

- Read Sensor PV and Output Information

- Write Short and Long Tag

- Write Descriptor and Message

- Select PV Unit

- Write PV Ranges (Upper and Lower)

- Enter/Exit Fixed Current Mode

- Set Zero Offset

- Trim D/A at 4mA & 20mA

The ability to store up to twenty HART device configuration files for uploading via the BetaLOG Hart software. Configurations can be stored as .csv or .txt files. This allows the end user to document the entire plant for HART devices without spending thousands of dollars for plant assetmanagement software.

NEW

Operation

The LC-110 & LC-110H utilizes a rotary encoder (Quick-Set Knob) to set the output (mA) and also to select the function to implement. The Quick-Set Knob features an integral push button that you press to enter a selection. A dedicated menu key brings up a list of functions. The Quick-Set interface highlights an item on that list, and then pressing the knob (clicking it) selects that item to drive further in the menu. The “Menu/Exit” key is used to go back to the previous menu or exit from menu structure into measure/source mode. All functions and HART commands are accessed in this manner. When used as mA calibrator only, there are dedicated keys for automatic step and ramp generation as well as keys to perform a quick zero and span (4mA, 20mA and 25% steps).

LC110 Series Ordering Information

*Each unit comes standard with batteries, manual, test leads (banana to alligator clips), and NIST Cert with Data

Part Number Description

1919974 LC110 Loop Calibrator 1920024 LC110H Loop Calibrator with HART™ Communications 1920050 BetaLOG HART Software with Lemo to USB Cable 6161102 Soft Carrying Case

1920051 LC110H Loop Calibrator Kit:

BetaLOG HART Software with Lemo to USB Cable Soft Carrying Case

Banana to Mini-grabber® Test Leads 1920049 Lemo to USB Cable 5353050 Test Leads (1 Pair – Banana to Alligator) 5353093 Test Leads (1 Pair – Banana to Minigrabber®)

Martel Electronics Corporation

3 Corporate Park Drive, Unit 1 Derry, NH 03038

Specifications subject to change without notice

Distributed by: