Page 1
Marshall Electronics
Model No. V-LCD70W-SH
7” 3G-SDI / HDMI Professional Camera-Top Monitor
Broadcast A/V Division
Operating Instructions
Ver. 1.0
Page 2
V-LCD70W-SH Operation Manual
Table of Contents
1. Installation & Initial Setup...........................................……..... .................. 3
2. Top & Front Panel Features ...................................................................... 4
3. Rear Panel Features ................................................................................. 5
4. Compatible Input Formats ....................................................................... 6
5. Main Menu & Navigation.................................................…... ................... 7
6. Specifications ........................................................................................... 10
7. Sun Hood Installation………................................................….... ............. 11
8. Included Accessories………................................................…...... ........... 11
9. Troubleshooting………................................................…...... ................... 11
10. Maintenance………................................................…...... ........................ 12
11. Warranty………................................................…...... ............................... 13
IMPORTANT SAFETY INSTRUCTIONS:
The V-LCD70W-SH has been tested for conformance to safety regulations
and requirements, and has been certied for international use. However, like
all electronic equipment, the V-LCD70W-SH should be used with care. Please
read and follow the safety instructions to protect yourself from possible injury
and to minimize the risk of damage to the unit.
• Please do not place the display screen towards the ground to avoid scratching the LCD surface.
• Please avoid heavy impact.
• Please do NOT use chemical solutions to clean this product. Simply wipe with a clean soft cloth to
maintain the brightness of the surface.
• Please do not block any vent hole.
• Please follow the instructions and trouble-shooting to adjust the product.
• Internal adjustments or repairs must be performed by a qualied technician.
2
Marshall Electronics
Page 3
1. Installation & Initial Setup
Unpacking
Carefully unpack the V-LCD70W-SH monitor and verify that the following items are included:
• V-LCD70W-SH Monitor
• 12V-2A Power Supply
• Operating Instructions
• Sun Hood
Supplied mounting screws:
• KM2.5*6MM x4 (used for Marshall base plate Part# 0032-1308A)
• PM2.5*12MM x4 (used for Marshall VM mount Part# 0032-1301A for IDX battery)
• PM4*6MM x4 (used for VESA mount screw holes)
Inspect the unit for any physical damage that may have occurred during shipping. Should there be
any damage, immediately contact Marshall Electronics at (800) 800-6608.
If you are not located within the continental United States, call +1 (310) 333-0606.
Connections, Power-On and Initial Setup
a. Plug the power supply into an AC power source (100-240 V @ 50/60 Hz).
b. Attach the Power connector to the back of the monitor.
c. Connect the required cables for video signal input and output.
d. Press the Power button to turn the unit on, then press Input to select either HDMI or SDI source
as derived.
www.LCDracks.com
3
Page 4
V-LCD70W-SH Operation Manual
2. Top & Front Panel Features
1
4
5
2
3
F1~F3 user-de ned function buttons.
1
Shortcut: Long press on any function button (3-5 seconds) pops up menu for setting.
Press Up/Down buttons to choose settings, then press the Menu button to con rm the
selection.
Functions of F1-F3 buttons can be set to:
Center Marker, Aspect Marker, Check Field, Underscan, Scan, Aspect, DSLR, Freeze,
H/V delay, Peaking, False Color, Exposure, Histogram, Level Meter, Waveform and Time
Code.
Default function: F1: Waveform F2: Scan F3: Aspect
POWER button
2
Battery indicator light. ( Red light - OFF mode, green light - Operating mode).
3
6
7
INPUT: Switch between SDI and HDMI.
4
▲/▼ Select option in the menu. Increase or decrease the option value.
5
Menu: Select button
6
Headphone jack. Accepts standard 3.5mm mini-phone plug.
7
4
Marshall Electronics
Page 5
3. Rear Panel Features
4
21 3
1. Serial Digital “BNC” Connectors
SDI input and loop out. Conversion is possible between HDMI and SDI inputs. See System
section of menu. Compatible with SDI, HD SDI and 3G SDI inputs. Embedded audio may be
monitored at the Headphone jack and visually monitored on-screen.
2. TALLY Connector
The tally light above each monitor is controlled by grounding the appropriate pin on the Tally
connector as shown in the table.
Caution: External power should never be applied to the Tally connector.
3. HDMI Digital Video Connectors
HDMI input and loop out. Conversion is possible between HDMI and SDI inputs. See System
section of menu. Embedded audio may be monitored at the Headphone jack and visually
monitored on-screen.
4. Power Connector. DC power input.
www.LCDracks.com
5
Page 6
V-LCD70W-SH Operation Manual
4. Compatible Input Formats
3G-HD-SDI Input
525i/59.94, 60, 625i/50
720p/25, 29.97, 30, 50, 59.94, 60
1080p/23.98, 23.98sF, 24, 24sF, 25, 29.97, 30
1080i/50, 59.94, 60
3G – Level A
1080p/ 60, 59.94, 50
HDMI Input
480p59.94, 576p50
720p/25, 29.97, 30, 50, 59.94, 60
1080p/23.98, 23.98sF, 24, 24sF, 25, 29.97, 30
1080p/ 50, 59.94, 60
1080i/50, 59.94, 60
HDMI / SDI Conversions
480i59.94, 576i50
720p/25, 29.97, 30, 50, 59.94, 60
1080p/23.98, 23.98sF, 24, 24sF, 25, 29.97, 30
1080p/ 50, 59.94, 60
1080i/50, 59.94, 60
6
Marshall Electronics
Page 7
5. Main Menu & Navigation
1. Using the menu buttons
When power on, press “MENU” on the device. The menu will display on the screen.
Press ▲ / ▼ button to choose menu item
Then press “MENU” button to conrm
ITEMS OPTIONS
Exit
Video Conguration
Marker Conguration
Function Conguration
Waveform Conguration
Audio Conguration Volume, Level Meter, Audio Ch
System Conguration
Brightness, Contrast, Saturation, Sharpness, Color Temp, R Gain, G
Gain, B Gain, R Oset, G Oset, B Oset
Center Marker, Aspect Marker, Safety Marker, Marker Color, Marker
Mat, Thickness.
Scan, Aspect, Underscan, H/V Delay,
Check Field, Zoom, Freeze,3G Format, DSLR
Waveform, Waveform Trans, Peaking, Peaking Color, Peaking Level,
False Color, Exposure, Exposure Level, Histogram, Time Code
Language, HDMI/SDI Convert, Color Bar, Menu Timer, Image Flip,
Back Light, Fan, Reset, Version
www.LCDracks.com
7
Page 8
V-LCD70W-SH Operation Manual
ITEMS OPTIONS
Exit
Brightness 0~100
Contrast 0~100
Saturation 0~100
Sharpness 0~100
Color Temp
ITEMS OPTIONS
Exit
Center Marker On, O
Aspect Marker O, 3: 2, 4:3, 2.35:1, 1.85:1, 16:9
Safety Marker O, 80%, 85%, 88%, 90%, 93%, 95%
Marker Color Red, Green, Blue, White, Black
Marker Mat O, 1~7
Thickness 2, 4, 6
5500ºK / 6500ºK / 7500ºK / 9300ºK / User
R Gain 0-255
G Gain 0-255
B Gain 0-255
R Oset 0-511
G Oset 0-511
B Oset 0-511
Note:
Only available under
“User” mode to meet
the color value you
need.
8
ITEMS OPTIONS
Exit
Scan Pix.To Pix. Zoom, Aspect,
Aspect 16:9, 1.85:1, 2.35:1, 4:3, 3:2, Full
Underscan On, O
H/V Delay O, H, V, H/V
Check Field O, Red, Green, Blue
Zoom ×2, ×3, ×4, ×5, ×6, ×7, ×8
Freeze ON, O
SDI INPUT
3G Format
HDMI INPUT
DSLR
Normal, GBRA444 10Bit, YCbCrA444 10Bit,
YCbCrA422 12Bit, GBR444 12Bit, YCbCr444
12Bit
5D3
5D2 DSLR MODE
OFF
Marshall Electronics
Page 9
ITEMS OPTIONS
Exit
Waveform O, Multi, Y, YCbCr, RGB
Waveform Trans. O, 20%, 50%
Peaking On, O
Peaking Color Red, Green , Blue, White
Peaking Level 0~100
False Color On, O
Exposure On, O
Exposure Level 0~100
Histogram Y, RGB, Color
TimeCode (SDI Input Only) O, VITC, LTC
ITEMS OPTIONS
Exit
Volume 0~100
Level Meter On, O
Audio Ch Ch1&Ch2, Ch3&Ch4, Ch5&Ch6, Ch7&Ch8,
ITEMS OPTIONS
Exit
Language English, Chinese
HDMI/SDI Convert On, O
Color Bar On, O
r
Menu Timer 10s, 20s, 30s
Image Flip O, H, V, H/V
Back Light 0~100
Fan O, Low, High
Exposure Level On, O
Version V1.3
www.LCDracks.com
9
Page 10
V-LCD70W-SH Operation Manual
6. Specifications
Screen Size 7” Diagonal
Aspect Ratio 16:10
PANEL
VIDEO INPUT / OUTPUT*
CONNECTORS
Tally Hardware Interface HD-15 Female
Stereo Headphone Jack 1/8” (3.5mm) Female Jack
Power Input DC Connector
ELECTRICAL
MECHANICAL
DIMENSIONS (H x W x D) 125mm x 196mm x 28.2mm / 4.9” x 7.7” x 1.11”
Resolution 1920 x 1200
Viewing Angle (h x v) 170° x 170° (H/V)
Brightness 450 cd/m
Contrast Ratio 1000:1
3G-HD-SDI Input / Output 2 x BNC Female (75 Ω)
HDMI Input / Output 2 x HDMI Female
HDMI Video Input
HDMI Video Output
3G-HD-SDI Video Input
3G-HD-SDI Video Output
Power Consumption 1.1A @ 12VDC (13 W)
Voltage Requirement 12 VDC (7 – 15VDC)
Weight 1.20 lbs
Operating Temperature -4°F ~ 140°F (-20°C ~ 60°C)
Storage Temperature -22°F ~ 158°F (-30°C ~ 70°C)
2
* Maximum 1 loop out for the best result
TALLY HARDWARE INTERFACE (HD-15)
Activation requires contact closure of pin to ground on the HD-15 connector:
Pin No. Signal
1 Green
2 Red
3 Yellow
4 Ground
5 NC
6 N/C
7 N/C
8 N/C
9 N/C
10 N/C
11
12
13
14
15
N/C
N/C
N/C
N/C
N/C
10
Marshall Electronics
Page 11
7. Sun Hood Installation
Sun Hood is designed for use with
V-LCD70W-SH to shield the monitor from glare.
It features three-sided folding design.
Snap the Sun Hood to the front of the monitor.
8. Included Accessories
1. Sun Hood
2. DC 12V Power adapter
3. Operations Manual
9. Troubleshooting
1. Power on, but no picture:
Check whether the cables are correctly connected. Also, please use the standard power adapter
coming with the product package or other power supply with the correct voltage and pin
con guration.
2. Only black-and-white display:
Check whether the color saturation and brightness are properly set. Access the Video menu and
make sure Check Field is Off
3. Wrong or abnormal colors:
Check whether the cables are correctly connected. Broken or loose pins of the cables may cause a
bad connection. Access the Waveform menu and make sure False Color is off.
4. Picture is “stuck” on screen:
Access the Video menu page and check that FREEZE INPUT is off.
5. Other problems:
The monitor can be reset to Factory original settings. This is sometimes useful to eliminate the
possibility that an improperly set menu item is interfering with the operation. To reset the monitor,
access the “System Con guration” menu page, press the Menu knob then rotate left or right to
select “Reset”. Press the knob once then rotate the knob to cause the unit to reset.
www.LCDracks.com
11
Page 12
V-LCD70W-SH Operation Manual
10. Maintenance
Screen Cleaning
Periodically clean the screen surface using ammonia-free cleaning wipes (Marshall Part No.
V-HWP-K). A clean micro-ber cloth can also be used using only non-abrasive and ammonia-free
cleaning agents. Do not use paper towels. Paper towel bers are coarse and may scratch the
surface of the polycarbonate faceplate or leave streaks on the surface. Antistatic and ngerprint
resistant cleaning agents are recommended. Do not apply excessive pressure to the screen to
avoid damaging the LCD.
Faceplate Dusting
Dust the unit with a soft, damp cloth or chamois. Dry or abrasive cloths may cause electrostatic
charge on the surface, attracting dust particles. Neutralize static electricity effects by using the
recommended cleaning and polishing practice.
12
Marshall Electronics
Page 13
11. Warranty
Marshall Electronics warranties to the rst consumer that this V-LCD70W-SH LCD monitor will,
under normal use, be free from defects in workmanship and materials, when received in its original
container, for a period of one year from the purchase date.
This warranty is extended to the rst consumer only, and proof of purchase is necessary to honor
the warranty. If there is no proof of purchase provided with a warranty claim, Marshall Electronics
reserves the right not to honor the warranty set forth above.
Therefore, labor and parts may be charged to the consumer. This warranty does not apply to the
product exterior or cosmetics. Misuse, abnormal handling, alterations or modications in design
or construction void this warranty. It is considered normal for a minimal amount of pixels, not to
exceed three, to fail on the periphery of the display active viewing area. Marshall Electronics
reserves the option to refuse service for display pixel failure if deemed unobtrusive to effective use
of the monitor by our technicians.
No sales personnel of the seller or any other person is authorized to make any warranties other
than those described above, or to extend the duration of any warranties on behalf of Marshall
Electronics, beyond the time period described above.
Due to constant effort to improve products and product features, specications may change
without notice.
www.LCDracks.com
13
Page 14
Marshall Electronics, Inc.
20608 Madrona Avenue
Torrance, CA 90503
Tel: (800) 800-6608 / (310) 333-0606 • Fax: 310-333-0688
www.LCDracks.com
support@marshall-usa.com
V-LCD70W-SH Operation Manual • Version 1.0
Loading...